Directionally solidified （DS） specimens of Nb-Ti-Si based ultrahigh temperature alloy were heat-treated at （1 500 ℃, 50 h） and （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, respectively. The results show that the mic...Directionally solidified （DS） specimens of Nb-Ti-Si based ultrahigh temperature alloy were heat-treated at （1 500 ℃, 50 h） and （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, respectively. The results show that the microstructures become uniform, the long and big primary （Nb,X）sSi3 （X represents Ti and Hf elements） plates in the DS specimens are broken into small ones, and the eutectic cells lose their lamellar morphology and their interfaces become blurry after heat-treatment. Meanwhile, the （Nb,X）sSi3 slices in the eutectic cells of the DS specimens coarsen obviously after heat-treatment. Homogenizing and aging treatments could effectively eliminate elemental microsegregation, and the segregation ratios of all elements in niobium solid solution （Nbss） in different regions tend to 1. After heat-treatment, the microhardness of retained eutectic cells increases evidently, and the maximum value reaches HV1 404.57 for the specimen directionally solidified with a withdrawing rate of 100 μm/s and then heat-treated at （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, which is 72.8 % higher than that under DS condition.展开更多
Zr-Y jointly modified silicide coatings were prepared on an Nb-Ti-Si-Cr based ultrahigh temperature alloy by pack cementation process. The wear behaviors of both the base alloy and coatings were comparatively studied ...Zr-Y jointly modified silicide coatings were prepared on an Nb-Ti-Si-Cr based ultrahigh temperature alloy by pack cementation process. The wear behaviors of both the base alloy and coatings were comparatively studied at room temperature and 800 ℃ using SiC balls as the counterpart. The Zr-Y jointly modified silicide coating is mainly composed of a thick （Nb,X）Si2 outer layer and a thin （Ti,Nb）5Si4 inner layer. The coatings possess much higher microhardness than the base alloy. The wear rates of both the base alloy and coatings increase with increasing the sliding loads. However, the coatings have much lower wear rates than the base alloy under the same sliding conditions. The coatings have superior anti-friction property, and can provide effective protection for the base alloy at both room temperature and 800 ℃ in air.展开更多
The isothermal sections of the Nb Ti Si ternary system at 1?473?K and 1?373?K were determined by means of diffusion triple technique and electron microprobe analysis. By analyzing the diffusion layers in the diffusion...The isothermal sections of the Nb Ti Si ternary system at 1?473?K and 1?373?K were determined by means of diffusion triple technique and electron microprobe analysis. By analyzing the diffusion layers in the diffusion couples, the titanium silicides and niobium silicides forming in this system were identified. The results show that no ternary compounds formed in the Nb Ti Si ternary system at the test temperatures. The phase transformations occurring on cooling from 1?473?K to 1?373?K were discussed.展开更多
基金Project(51071124)supported by the National Natural Science Foundation of ChinaProject(CX200605)supported by the Doctorate Foundation of Northwestern Polytechnical University,ChinaProject(20096102110012)supported by a Special Research Fund for Doctoral Disciplines in Colleges and Universities of the Ministry of Education,China
文摘Directionally solidified （DS） specimens of Nb-Ti-Si based ultrahigh temperature alloy were heat-treated at （1 500 ℃, 50 h） and （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, respectively. The results show that the microstructures become uniform, the long and big primary （Nb,X）sSi3 （X represents Ti and Hf elements） plates in the DS specimens are broken into small ones, and the eutectic cells lose their lamellar morphology and their interfaces become blurry after heat-treatment. Meanwhile, the （Nb,X）sSi3 slices in the eutectic cells of the DS specimens coarsen obviously after heat-treatment. Homogenizing and aging treatments could effectively eliminate elemental microsegregation, and the segregation ratios of all elements in niobium solid solution （Nbss） in different regions tend to 1. After heat-treatment, the microhardness of retained eutectic cells increases evidently, and the maximum value reaches HV1 404.57 for the specimen directionally solidified with a withdrawing rate of 100 μm/s and then heat-treated at （1 500 ℃, 50 h） ＋ （1 100 ℃, 50 h）, which is 72.8 % higher than that under DS condition.
基金Projects(51371145,51431003,U1435201,51401166)supported by the National Natural Science Foundation of ChinaProject(B080401)supported by the Programme of Introducing Talents of Discipline to Universities,China
文摘Zr-Y jointly modified silicide coatings were prepared on an Nb-Ti-Si-Cr based ultrahigh temperature alloy by pack cementation process. The wear behaviors of both the base alloy and coatings were comparatively studied at room temperature and 800 ℃ using SiC balls as the counterpart. The Zr-Y jointly modified silicide coating is mainly composed of a thick （Nb,X）Si2 outer layer and a thin （Ti,Nb）5Si4 inner layer. The coatings possess much higher microhardness than the base alloy. The wear rates of both the base alloy and coatings increase with increasing the sliding loads. However, the coatings have much lower wear rates than the base alloy under the same sliding conditions. The coatings have superior anti-friction property, and can provide effective protection for the base alloy at both room temperature and 800 ℃ in air.
文摘The isothermal sections of the Nb Ti Si ternary system at 1?473?K and 1?373?K were determined by means of diffusion triple technique and electron microprobe analysis. By analyzing the diffusion layers in the diffusion couples, the titanium silicides and niobium silicides forming in this system were identified. The results show that no ternary compounds formed in the Nb Ti Si ternary system at the test temperatures. The phase transformations occurring on cooling from 1?473?K to 1?373?K were discussed.
