Effect of Shot Peening on Surface Damage Evolution Behavior of Cu-19Ni Alloy

Shot peening is a surface modification technology with the metal surface nano machine(SNC),which can modify the surface microstructure and extend the fatigue life of Cu-19Ni alloy.The hardness,damage evolution and mechanical properties were investigated and characterized by scanning electron microscope(SEM),laser confocal microscope(LSM)and material surface performance tester(CFT).The results showed that the surface roughness and friction coefficient of Cu-19Ni alloy decreased with the increase of shot peening duration and diameter,while the microhardness and strength increased.Moreover,with the increase in shot peening duration and diameter,SEM observation showed that the fracture dimples became smaller,meanwhile,with the increase of small cleavage planes,shear tearing ridges and the thickness of the surface nano layer,the fracture mode gradually evolved from plastic to brittle fracture.The uniaxial tensile test of shot peened Cu-19Ni alloy was carried out by MTS testing machine combined with digital image correlation technology(DIC).The evolution of Cu-19Ni surface damage was analyzed,and the evolution equations describing the damage of large deformation zone and small deformation zone were established.The effect of shot peening on the damage evolution behavior of Cu-19Ni alloy was revealed.

Influence of heat treatment on electrochemical properties of Ti_(1.4)V_(0.6)Ni alloy electrode containing icosahedral quasicrystalline phase

The structures and electrochemical properties of the Ti1.4V0.6Ni ribbon before and after heat treatment are investigated systematically. The structure of the sample is characterized by X-ray powder diffraction analysis. Electrochemical properties including the discharge capacity, the cyclic stability and the high-rate discharge ability are tested. X-ray powder diffraction analysis shows that after heat treatment at 590 °C for 30 min, all samples mainly consist of the icosahedral quasicrystal phase (I-phase), Ti2Ni phase (FCC), V-based solid solution phase (BCC) and C14 Laves phase (hexagonal). Electrochemical measurements show that the maximum discharge capacity of the alloy electrode after heat treatment is 330.9 mA?h/g under the conditions that the discharge current density is 30 mA/g and the temperature is 30 °C. The result indicates that the cyclic stability and the high-rate discharge ability are all improved. In addition, the electrochemical kinetics of the alloy electrode is also studied by electrochemical impedance spectroscopy (EIS) and hydrogen diffusion coefficient (D).

Effect of rare earths on corrosion resistance of Cu-30Ni alloys in simulated seawater

Cu-30Ni-xRE(x=0–0.213 wt.%) alloy was prepared by adding rare earths(RE) in melted Cu-30Ni alloy using metal mould casting method.The effects of RE on corrosion resistance of the alloy in simulated seawater were investigated using optical microscope,scanning electronic microscope with energy-dispersive spectrometer and electrochemical measurement system.The results showed that the corrosion resistance of Cu-30Ni alloy was greatly improved by adding proper amount of RE,whereas excess addition of RE worsened ...

Microstructure features and mechanical/electrochemical behavior of directionally solidified Al−6wt.%Cu−5wt.%Ni alloy

The effects of the addition of 5.0 wt.%Ni to an Al−6wt.%Cu alloy on the solidification cooling rate(T),growth rate(V_(L)),length scale of the representative phase of the microstructure,morphology/distribution of intermetallic compounds(IMCs)and on the resulting properties were investigated.Corrosion and tensile properties were determined on samples solidified under a wide range of T along the length of a directionally solidified Al−6wt.%Cu−5.0wt.%Ni alloy casting.Experimental growth laws were derived relating the evolution of primary(λ_(1))and secondary(λ_(2))dendritic spacings with T and V_(L).The elongation to fracture(δ)and the ultimate tensile strength(σ_(U))were correlated with the inverse of the square root of λ_(1) along the length of the casting by Hall−Petch type experimental equations.The reinforcing effect provided by the addition of Ni in the alloy composition is shown to surpass that provided by the refinement of the dendritic microstructure.The highest corrosion resistance is associated with a microstructure formed by thin IMCs evenly distributed in the interdendritic regions,typical of samples that are solidified under higher T.

Effects of solid solution treatment and cooling on morphology of LPSO phase and precipitation hardening behavior of Mg-Dy-Ni alloy

Effects of solid solution treatment and cooling on the morphology of long period stacking order(LPSO)phase and precipitation hardening behavior of Mg?2Dy?0.5Ni(molar fraction,%)alloy were investigated.Microstructures of the as-cast alloy mainly consisted ofα-Mg phase,bamboo-like Mg12DyNi phase with LPSO structure distributed between dendrites and small amounts of cubic Dy phases.During solid solution treatment at565oC for12h and subsequent different cooling conditions,dot-shaped,block,fine lamellar and rod-shaped LPSO phases precipitate in Mg matrix,respectively.For continuous cooling conditions(furnace and air cooling),the fine lamellar LPSO phase generally forms in grain interior and its volume fraction increases and block LPSO phase coarsens with increasing cooling time.For discontinuous cooling conditions(air cooling after furnace cooling to415and265°C),the dot-shaped LPSO grows into the rod-shaped phase,which results in an decrease of cooling hardening behavior of alloy.

Properties of oxide films grown on 25Cr20Ni alloy in air-H_2O and H_2-H_2O atmospheres

The oxidation kinetics,surface morphology and phase structure of oxide films grown on 25Cr20Ni alloy in air-H2O and H2-H2O atmospheres at 900 ℃ for 20 h were investigated.The anti-coking performance and resistance to carburization of the two oxide films were compared using 25Cr20Ni alloy tubes with an inner diameter of 10 mm and a length of 850 mm in a bench scale naphtha steam pyrolysis unit.The oxidation kinetics followed a parabolic law in an air-H2O atmosphere and a logarithm law in a H2-H2O atmosphere in the steady-state stage.The oxide film grown in the air-H2O atmosphere had cracks where the elements Fe and Ni were enriched and the un-cracked area was covered with octahedral-shaped MnCr2O4 spinels and Cr1.3Fe0.7O3 oxide clusters,while the oxide film grown in the H2-H2O atmosphere was intact and completely covered with dense standing blade MnCr2O4 spinels.In the pyrolysis tests,the anti-coking performance and resistance to carburization of the oxide film grown in the H2-H2O atmosphere were far better than that in the air-H2O atmosphere.The mass of coke formed in the oxide film grown in the H2-H2O atmosphere was less than 10％ of that in the air-H2O atmosphere.The Cr1.3Fe0.7O3 oxide clusters converted into Cr23C6 carbides and the cracks were filled with carbon in the oxide film grown in the air-H2O atmosphere after repeated coking and decoking tests,while the dense standing blade MnCr2O4 spinels remained unchanged in the oxide film grown in the H2-H2O atmosphere.The ethylene,propylene and butadiene yields in the pyrolysis tests were almost the same for the two oxide films.

Effect of hot rolling on microstructure and tribology behaviors of Ti-50.8Ni alloy

We link different microstructures to tribological behaviors of Ti-50.8 Ni(mole fraction, %) in reciprocating mode at room temperature(20 ℃). Hot-rolled alloys with B2 phase exhibit lower coefficient of friction and wear rate compared to the ones with B19?. Stress-induced martensitic transformation occurs during sliding. However, multi-pass hot rolling weakens the wear resistance. In this study, microstructures were characterized through electron backscatter diffraction and transmission electron microscopy(EBSD/TEM). From the concept of energy conservation, the effects of weak intensity of hot-rolled textures on the wear resistance are minimal. Based on the result that the alloy with a higher portion of coincidence site lattice boundaries shows lower martensitic start transformation temperature in the DSC curves than that with higher KAM values, the delay on B2-B19? transformation from {112}B2 twins outweighs dislocations. Moreover, widely distributed small-angle grain boundaries owing to dynamic recovery improve the wear resistance effectively compared to those that are well-recrystallized.

Pre-bainitic Transformation in Fe-Ni Alloy

The behaviour of the pre bainitic transformation in Fe Ni alloy was investigated by using SAM, X ray diffraction and TEM. The results show that there is segregation of Ni atoms in austenite and that bainite forms in depleted regions of Ni atoms.

Influence of microstructure and surface condition on antifouling property of 90Cu-10Ni alloy in seawater

Through the experiment of natural seawater exposure corrosion, the antifouling properties of the plate specimens of 90Cu 10Ni alloy were studied, which were processed by different deformations, annealing treatments and surface treatments. The results indicate that after exposure corrosion for half a year, the antifouling properties of the specimens are quite different. The specimens processed by suitable deformations, annealing treatment at 650?℃ and pretreatment of surface film possess both good corrosion resistance and antifouling properties. However, the specimens processed by different deformations and annealing treatment at 450?℃ possess lower corrosion resistance, although they are also treated by the pretreatment of surface film; their antifouling properties change with different deformations. The relationships among the corrosion morphology and microstructure with the antifouling property of 90Cu 10Ni alloy are observed under the scanning electron microscopy (SEM).

Magnetization-Enhanced Dislocation Motion and Decreased Yield Strength of 60Fe40Ni Alloy

Using a special constant deflection device, the changes in dislocation configuration ahead of a loaded crack tip for 60Fe40Ni alloy. before and after magnetization in a magnetic field, have been studied in TEM. The results showed that the magnetization for 60Fe40Ni alloy could enhance dislocation emission, multiplication and motion. Also, the mechanical properties of 60Fe40Ni alloy, in air and in the magnetic field respectively have been investigated using the slow strain rate tension. And the results indicated that magnetization could make the yield strength corresponding to decrease by 26 percent, but did not influence the ultimate tensile strength and the fracture strain, which showed that magnetization could enhance plastic deformation.

Hydriding-dehydriding properties of Mg_2Ni alloy modified by ball-milling in tetrahydrofuran

A new approach of ball-milled Mg_2Ni in tetrahydrofuran (THF) to improve thehydriding kinetics of Mg_2Ni alloy is suggested and studied. It is found that the modified alloydisplayed the improved activity for hydriding even at relatively low temperature (e.g., 323-373 K).In the case of the sample milled in THF for 20 h, the hydrogen content (mass fraction) reaches 1.6 %at 323 K, 2.1% at 348 K and 3.4% at 448 K, respectively. The use of THF during grinding led to thechange of the structure, which is reflected by the broadening and weakening of the diffraction peaksin the XRD spectra. The XPS analysis shows that Mg (2s) binding energy peak of Mg_2Ni aftermodification shifted from a lower binding energy to a higher one, indicating the charge transferencebetween Mg and THF and the formation of catalytically active electron donor-acceptor (EDA)complexes on the surface of modified Mg_2Ni alloy.

Electrochemical Isolation and Determination of GCP Phase in a Fe-Cr-Ni Alloy

Geometrical Close Packed (GCP) phase in Fe Cr Ni alloy was quantitatively isolated and precisely determined when electrolyzed in 10 % H 3PO 4 electrolyte at a low current density of 5 mA/cm 2 and 22 ℃±1 ℃. The transpassive dissolution potential of the alloy matrix under above conditions is about 1 140 mV (SCE), at which GCP phase is in passive state and can be isolated from the alloy.[WT5”HZ〗

EFFECT OF INTERGRANULAR CARBIDES ON CREEP RUPTURE PROPERTIES OF Fe-15Cr-25Ni ALLOY

The intergranular carbides may significantly increase rupture life and ductility of the Fe-15Cr-25Ni alloy.This seems due to the grain boundary sliding and diffusion hindered by precipitation of intergranular carbides,so the nucleation and growth rate of cracks or cavities are reduced.

Influence of Rare Earth Elements on Mechanical Properties and Corrosion Resistance of Cu-15Ni Alloy

In order to improve the mechanical property and Cl- ＋ S2- corrosion resistance of B15 copper.nickel alloy, Cu.15Ni-xRE （x： 0-0.1% by weight） alloy was prepared by adding rare earth （RE） in melted Cu-15Ni alloy using metal mould casting method. Optical microscopy（ OM）, electronic tensile testing machine, X-ray diffraction （ XRD ）, scanning electron microscope （ SEM ）, and electrochemical testing system were used to analyze mechanical property, corrosion resistance property, and surface microstructure of different treatment samples. The results of OM and tensile testing show that the RE addition can effectively deoxidize the alloy melt and the microstructura of the alloy changes from coarse dendrite to small equlaxed grain. By addition of 0.05 % RE, the tensile strength and elongation of Cu-15Ni alloys are improved from 294 MPa to 340 MPa, and 8 % to 33.5 % respectively. The results of electrochemical testing show that the corrosion resistance of Cu-15Ni alloy is greatly improved by adding proper amount of RE, whereas excess addition of RE worsens the corrosion resistance. The optimum RE content was about 0.05 % by weight. In comparison with the alloy without RE, the corrosion potential and corrosion current density of Cu-15Ni alloy containing proper RE decreased by about - 0. 28 V and 70 A/cm2, respectively.

Cavitation Erosion Behavior of as-Welded Cu12Mn8Al3Fe2Ni Alloy

Cavitation erosion behavior of as-welded Cu12Mn8Al3Fe2Ni alloy in 3.5% NaCl aqueous solution was studied bymagnetostrictive vibratory device for cavitation erosion. The results show that the cavitation erosion resistance ofthe as-welded Cu12Mn8Al3Fe2Ni alloy is much more superior to that of the as-cast one. The cumulative mass lossand the mass loss rate of the as-welded Cu12Mn8Al3Fe2Ni alloy are almost 1/4 that of the as-cast one. SEM analysisof eroded specimens reveals that the as-cast Cu12Mn8Al3Fe2Ni alloy is attacked more severely than the as-weldedone. Microcracks causing cavitation damage initiate at the phase boundaries.

Electrochemical Hydrogen Absorbing/Desorbing Behavior of Double Phase Mg-Ni Alloy

The electrochemical performance of double phase Mg Ni alloy was characterized at 25°C and 70°C, in order to evaluate briefly its utility as negative electrode materials in nickel metal hydride batteries. The results show that the electrochemical capacity of double phase Mg Ni alloy is rarely low at 25°C, but increased rapidly when the temperature is enhanced, and the double phase Mg Ni alloy has its maximum capacity at the first discharge cycle, but the capacity degrades rapidly with cycling number.

First-principles calculations of Ni–(Co)–Mn–Cu–Ti all-d-metal Heusler alloy on martensitic transformation,mechanical and magnetic properties

The martensitic transformation,mechanical,and magnetic properties of the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) (x=0.125,0.25,0.375,0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5)[(x=0.125,y=0.125,0.25,0.375,0.5) and (x=0.125,0.25,0.375,y=0.625)]alloys were systematically studied by the first-principles calculations.For the formation energy,the martensite is smaller than the austenite,the Ni–(Co)–Mn–Cu–Ti alloys studied in this work can undergo martensitic transformation.The austenite and non-modulated (NM) martensite always present antiferromagnetic state in the Ni_(2)Mn_(1.5-x)Cu_(x)Ti_(0.5) and Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) (y<0.625) alloys.When y=0.625 in the Ni_(2-y)Co_(y)Mn_(1.5-x)Cu_(x)Ti_(0.5) series,the austenite presents ferromagnetic state while the NM martensite shows antiferromagnetic state.Cu doping can decrease the thermal hysteresis and anisotropy of the Ni–(Co)–Mn–Ti alloy.Increasing Mn and decreasing Ti content can improve the shear resistance and normal stress resistance,but reduce the toughness in the Ni–Mn–Cu–Ti alloy.And the ductility of the Co–Cu co-doping alloy is inferior to that of the Ni–Mn–Cu–Ti and Ni–Co–Mn–Ti alloys.The electronic density of states was studied to reveal the essence of the mechanical and magnetic properties.

Microstructure and high temperature tribological behavior of laser cladding Ni60A alloys coatings on 45 steel substrate

The crack-free Ni60 A coating was fabricated on 45 steel substrate by laser cladding and the microstructure including solidification characteristics, phases constitution and phase distribution was systematically investigated. The high temperature friction and wear behavior of the cladding coating and substrate sliding against GCr15 ball under different loads was systematically evaluated. It was found that the coating has homogenous and fine microstructure consisting of γ（Ni） solid solution, a considerable amount of network Ni-Ni3 B eutectics, m^23C6 with the floret-shape structure and Cr B with the dark spot-shape structure uniformly distributing in interdendritic eutectics. The microhardness of the coating is about 2.6 times as much as that of the substrate. The coating produces higher friction values than the substrate under the same load condition, but the friction process on the coating keeps relatively stable. Wear rates of the coating are about 1/6.2 of that of the substrate under the higher load（300 g）. Wear mechanism of the substrate includes adhesion wear, abrasive wear, severe plastic deformation and oxidation wear, while that of the coating is merely a combination of mild abrasive wear and moderate oxidation wear.

Electrodeposition of Er-Ni Alloy Film in Dimethylsulfoxide

The cyclic voltammetry and chronoamperometry were used to investigate the electrochemical behaviors of Er(Ⅲ) and Ni(Ⅱ) in LiClO 4 DMSO(dimethylsufoxide) system on Pt and Cu electrodes. Experimental results indicated that the reduction of Er(Ⅲ) to Er and Ni(Ⅱ) to Ni were irreversible in one step on Pt and Cu electrodes. The diffusion coefficient and electron transfer coefficient of Er(Ⅲ) in 0.01 mol·L -1 ErCl 3 -0.1 mol·L -1 LiClO 4 DMSO system at 303K were 1.47×10 -10 m 2·s -1 and 0.108 respectively, and the diffusion coefficient and electron transfer coefficient of Ni(Ⅱ) in 0.01 mol·L -1 NiCl 2-0.1 mol·L -1 LiClO 4 DMSO system at 303K were 3.38×10 -10 m 2·s -1 and 0.160 respectively. The homogeneous, strong adhesive Er Ni alloy films with metallic lu- stre was prepared by potentiostatic electrolysis on Cu electrode in ErCl 3 NiCl 2 LiClO 4 DMSO system at -1.90～ -2.55 V (vs SCE).

Hot corrosion behavior of Ni–16Cr–xAl based alloys in mixture of Na_2SO_4-NaCl at 600 ℃

The hot corrosion behaviors of Ni–16Cr–xAl（x=4.5%, 6.8%, 9.0%, mass fraction） based alloys in Na2SO4–25% NaCl molten salts at 600 °C were investigated. The effects of pre-oxidation and Al content on the resistance to hot corrosion were examined. The hot corrosion resistance of Ni–16Cr–xAl based alloy with Al addition from 4.5% to 9.0% increases with increasing Al content. The alloy with Al content of 9.0% shows the highest hot corrosion resistance among the examined alloys because more β–NiAl phases are obtained to sustain the Al2O3 scale repaired during hot corrosion. Pre-oxidized specimens have a superior hot corrosion resistance compared with the as-cast specimens, due to a protective oxide scale formed after pre-treatment.