期刊文献+
共找到25篇文章
< 1 2 >
每页显示 20 50 100
Study on ReactiveAdsorption Desulfurization of Model Gasoline on Ni/ZnO-HY Adsorbent 被引量:5
1
作者 Huang Huan Salissou M.Nour +2 位作者 Yi Dezhi Meng Xuan Shi Li 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2013年第3期57-64,共8页
The reactive adsorption desulfurization of model gasoline was carried out on Ni/ZnO-HY adsorbent.The Ni/ZnO-HY adsorbent was characterized by N2adsorption-desorption test(BET),X-ray diffractometry(XRD),and temperature... The reactive adsorption desulfurization of model gasoline was carried out on Ni/ZnO-HY adsorbent.The Ni/ZnO-HY adsorbent was characterized by N2adsorption-desorption test(BET),X-ray diffractometry(XRD),and temperature-programmed reduction(TPR)analysis.The test results have demonstrated that HY-zeolite is a feasible support for Ni/ZnO components used in reactive adsorption desulfurization.The results of XRD and TPR analyses showed that most of nickel element was present as Ni2+species with only a small part existing as Ni3+species,and the Ni2+species had interactions with HY-zeolite.Under the conditions of this study,which specified a 50% ratio of HY-zeolite in the adsorbent,a Zn/Ni molar ratio of 10,and a reduction temperature of 400℃,the Ni/ZnO-HY adsorbent showed the best desulfurization performance.The sulfur capacity of Ni/ZnO-HY adsorbent could be recovered to 92.19% of the fresh one after being subjected to regeneration at 500℃,and could be maintained at 82.17% of the fresh one after 5 regeneration cycles. 展开更多
关键词 desulfurization reactive adsorption S-Zorb ni/zno HY-zeolite
下载PDF
Difunctional Adsorbents Ni/ZnO–HZSM-5 on Adsorption Desulfurization and Aromatization of Olef in Reaction 被引量:1
2
作者 Jianzeng Du Yonghong Li Zhenyu Miao 《Transactions of Tianjin University》 EI CAS 2019年第2期143-151,共9页
Novel Ni/ZnO–HZSM-5 adsorbents were synthesized by incipient wetness impregnation. The Ni/ZnO–HZSM-5 adsorbent can achieve deep desulfurization and olefin aromatization at the same time. Thiophene sulfur was removed... Novel Ni/ZnO–HZSM-5 adsorbents were synthesized by incipient wetness impregnation. The Ni/ZnO–HZSM-5 adsorbent can achieve deep desulfurization and olefin aromatization at the same time. Thiophene sulfur was removed from 495 to less than 10 ppm via reactive adsorption desulfurization(RADS). Olefins were also converted into aromatics. HZSM-5 did not only support adsorbents but also cooperated with active Ni sites to catalyze olefins into aromatic hydrocarbons. Aromatization of 1-pentene, 2-pentene, 2-methyl-2-butene, and 1-hexene on adsorbents was investigated. The adsorbents were characterized by the Brunauer–Emmett–Teller, X-ray diffraction, temperature-programmed reduction, and temperature-programmed desorption of ammonia and thermogravimetric analysis. The experimental results showed that strong acids on the adsorbent disappeared after HZSM-5 loaded active metal sites, and almost no coke was generated on adsorbents in RADS. 展开更多
关键词 ni/zno-HZSM-5 desulfurization OLEFIN AROMATIZATION
下载PDF
Fabrication of hierarchical porous ZnO and its performance in Ni/ZnO reactive-adsorption desulfurization 被引量:7
3
作者 Liu Yunqi She Nannan +2 位作者 Zhao Jinchong Peng Tingting Liu Chenguang 《Petroleum Science》 SCIE CAS CSCD 2013年第4期589-595,共7页
To investigate the effect of texture structure on the desulfurization performance in the Ni/ZnO reactive adsorption desulfurization(RADS) system,two kinds of ZnO porous materials with rod-shaped morphology were synt... To investigate the effect of texture structure on the desulfurization performance in the Ni/ZnO reactive adsorption desulfurization(RADS) system,two kinds of ZnO porous materials with rod-shaped morphology were synthesized and their structure was characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),transmission electron microscopy(TEM),and N2 adsorption/desorption.The formation mechanisms of hierarchical porous ZnO(ZnO with meso and macro pores) were also studied.Their application performance was evaluated in the RADS process over Ni/ZnO absorbent.Due to the difference in structure between the two kinds of ZnO,the two ZnO based adsorbents showed different desulfurization activity. 展开更多
关键词 ni/zno reactive adsorption desulfurization texture structure hierarchical pore
下载PDF
Trail of sulfur during the desulfurization via reactive adsorption on Ni/ZnO 被引量:8
4
作者 Ye Song Bo Peng +3 位作者 Xue Yang Qiuqiao Jiang Jun Liu Wei Lin 《Green Energy & Environment》 SCIE CSCD 2021年第4期597-606,共10页
The reactive adsorption behavior of thiophene on the reduced Ni/ZnO sample was investigated by a combination of theoretical and experimental study.It is widely accepted that Ni is responsible for the sulfur-removal of... The reactive adsorption behavior of thiophene on the reduced Ni/ZnO sample was investigated by a combination of theoretical and experimental study.It is widely accepted that Ni is responsible for the sulfur-removal of thiophene to release S-free hydrocarbons.Such surface reaction was simulated by DFT method.It is demonstrated that thiophene is mainly adsorbed as p-complexation mode over metallic Ni.During desulfurization,the Se Ni bond is formed and the Ce S bond is thus split without pre-hydrogenation,resulting in the formation of Ni_(3)S_(2)phase and S-free C4 olefin which can be further saturated in the presence of H_(2).The S-transfer between Ni_(3)S_(2)and ZnO was monitored by in-situ XRD and STEM with EDS mapping.Two essential features were identified for efficient S-transfer,namely,1)the H_(2)atmosphere,and 2)the two phases are presented with close contact.Based on the acquired information,a general scenario of sulfur trail has been proposed for the desulfurization of thiophene on Ni/ZnO. 展开更多
关键词 desulfurization ni/zno Sulfur transfer S zorb process MECHAniSM
下载PDF
New insights into the mechanism of reactive adsorption desulfurization on Ni/ZnO catalysts:Theoretical evidence showing the existence of interfacial sulfur transfer pathway and the essential role of hydrogen
5
作者 Hou-Yu Zhu Nai-You Shi +8 位作者 Dong-Yuan Liu Rui Li Jing-Gang Yu Qi-Tang Ma Tu-Ya Li Hao Ren Yuan Pan Yun-Qi Liu Wen-Yue Guo 《Petroleum Science》 SCIE EI CSCD 2023年第5期3240-3250,共11页
As well known in the petroleum industry and academia,Ni/ZnO catalysts have excellent desulfurization performance.However,the sulfur transfer mechanism of reactive adsorption desulfurization(RADS)that occurs on Ni/ZnO ... As well known in the petroleum industry and academia,Ni/ZnO catalysts have excellent desulfurization performance.However,the sulfur transfer mechanism of reactive adsorption desulfurization(RADS)that occurs on Ni/ZnO catalysts remains controversial.Herein,a periodic Ni nanorod supported on ZnO slab was built to represent the Ni/ZnO system,and density functional theory calculations were performed to study the sulfur transfer process and the role of H_(2)within the process.The results elucidate that the direct solid-state diffusion of S from Ni to interfacial oxygen vacancies(Ov)is more favorable than the hydrogenation of S to SH/H_(2)S on Ni and the subsequent H_(2)S desorption,and accordingly,H_(2)O is produced on Ni rather than on ZnO.Ab initio thermodynamics analysis shows that the hydrogen atmosphere applied in preparing Ni/ZnO catalysts greatly promotes the O_(v)formation on ZnO surface,which accounts for the presence of interfacial O_(v)in freshly prepared catalysts.Under RADS condition,hydrogenation of interfacial O atoms to form O-H groups facilitates the reverse spillover of these lattice O atoms from ZnO to Ni,accompanied with the interfacial O_(v)generation.In contrast to the classic S transfer mechanism via H_(2)S,the present work clearly demonstrates that the interfacial S transfer is a feasible reaction pathway in the RADS mechanism.More importantly,the existence of interfacial O_(v)is an essential prerequisite for this interfacial S diffusion,and H_(2)plays a key role in facilitating the O_(v)formation. 展开更多
关键词 Reactive adsorption desulfurization ni/zno Interface Sulfur transfer Density functional theory
下载PDF
Effect of Mixed Oxide Support for Ni/ZnO in Reactive Adsorption Desulfurization
6
作者 Chen Weicheng Yu Xiaoling +2 位作者 Huang Huan Shi Li Meng Xuan 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2016年第4期11-18,共8页
The effect of mixed oxide support on the performance of Ni/ZnO in the reactive adsorption desulfurization(RADS) reaction was investigated in a fixed bed reactor by using thiophene as the sulfur-containing compound in ... The effect of mixed oxide support on the performance of Ni/ZnO in the reactive adsorption desulfurization(RADS) reaction was investigated in a fixed bed reactor by using thiophene as the sulfur-containing compound in the model gasoline. A series of oxide supports for Ni/ZnO were synthesized by the co-precipitation method and characterized by XRD, N_2-adsorption, TPR and NH_3-TPD techniques. It was found that the desulfurization capacity of Ni/ZnO was enhanced greatly when active components were supported on the proper mixed oxide. Ni/ZnO supported on oxides exhibited much higher desulfurization efficiency and sulfur adsorption capacity than the unsupported Ni/ZnO and the synthesized Ni/ZnO-SA adsorbent exhibited the highest efficiency for thiophene removal. The higher desulfurization activity and sulfur capacity of Ni/ZnO supported on SiO_2-Al_2O_3 with small particle size, high specific surface area and large pore volume could promote the high dispersion of active metal phase and the transfer of sulfur to ZnO with lower mass transfer resistance. γ-Al_2O_3 species could weaken the interaction of active phases and SiO_2 as well as could increase greatly the amount of weak acids. Therefore, these oxides could impose a great influence on the structure and chemical properties of the catalyst. 展开更多
关键词 reactive adsorption desulfurization ni/zno support effect mixed oxide
下载PDF
构筑Ni/ZnCO_(2)O_(4)@ZnO复合金属氧化物脱硫剂及其反应吸附脱硫-再生性能研究
7
作者 代璞 郭梦雅 +4 位作者 葛晖 樊彩梅 李学宽 李瑞 唐明兴 《燃料化学学报(中英文)》 EI CAS CSCD 北大核心 2024年第11期1706-1714,共9页
采用共沉淀法在ZnO中引入金属Co并使其形成复合金属氧化物,通过共沉淀-浸渍法构筑了不同Co含量的复合金属氧化物脱硫剂,考察其脱硫活性和再生性能。采用XRD、TEM、N_2低温吸附-脱附、XPS和H_(2)-TPR等对脱硫剂的结构和性质进行系统表征... 采用共沉淀法在ZnO中引入金属Co并使其形成复合金属氧化物,通过共沉淀-浸渍法构筑了不同Co含量的复合金属氧化物脱硫剂,考察其脱硫活性和再生性能。采用XRD、TEM、N_2低温吸附-脱附、XPS和H_(2)-TPR等对脱硫剂的结构和性质进行系统表征,证实得到了Ni/ZnCO_(2)O_(4)@ZnO结构的复合金属氧化物脱硫剂。复合金属氧化物脱硫剂中ZnCO_(2)O_(4)的形成有利于脱硫剂的颗粒尺寸减小、分散度提升、比表面积增大。反应后XRD显示,ZnCO_(2)O_(4)也可作为H_2S的吸附剂,从而提高了脱硫剂的硫吸附容量。所有的复合金属氧化物脱硫剂的脱硫性能显著优于Ni/ZnO,其中,Zn:Co物质的量比为1:1的脱硫剂NZCo-3具有最优的脱硫性能,该脱硫剂在反应温度300℃,氢压3 MPa,质量空速2.2 h^(-1),氢油体积比300的条件下脱硫率为100%,且经过六次循环后仍能够保持优异的脱硫性能。该研究结果为合理设计Ni/ZnO脱硫剂以提高其脱硫性能和再生性能提供新的思路。 展开更多
关键词 反应吸附脱硫 ZnCO_(2)O_(4)复合金属氧化物 ni/zno 脱硫剂再生
下载PDF
Ni/ZnO-SiO_2-Al_2O_3吸附剂上加氢汽油的深度临氢吸附脱硫 被引量:9
8
作者 周广林 孙文艳 +1 位作者 姜伟丽 周红军 《石油炼制与化工》 CAS CSCD 北大核心 2013年第7期17-21,共5页
采用等体积浸渍法和湿混法制备NiO/ZnO-SiO2-Al2O3吸附剂前体,经还原得到Ni/ZnO-SiO2-Al2O3吸附剂。利用XRD和压汞法对其晶体结构进行表征,采用固定床吸附实验评价吸附剂对加氢汽油的吸附脱硫性能。结果表明,与等体积浸渍法制备的吸附... 采用等体积浸渍法和湿混法制备NiO/ZnO-SiO2-Al2O3吸附剂前体,经还原得到Ni/ZnO-SiO2-Al2O3吸附剂。利用XRD和压汞法对其晶体结构进行表征,采用固定床吸附实验评价吸附剂对加氢汽油的吸附脱硫性能。结果表明,与等体积浸渍法制备的吸附剂前体相比,湿混法制备的吸附剂前体的比表面积大,孔体积相当,还原后所得吸附剂的脱硫活性好。以山东恒源石化公司的加氢汽油为原料,在吸附温度350℃、压力2.0MPa、进料液时体积空速7h-1、氢气与溶剂油体积比60的条件下,可以将加氢汽油中的硫质量分数从69gμ/g降至10gμ/g以下,而汽油RON仅降低0.6个单位,硫容量(w)约为9.98%。该吸附剂对原料有很好的适应性,可再生,多次循环使用后脱硫性能基本不变。 展开更多
关键词 氧化锌 吸附剂 加氢汽油 脱硫
下载PDF
Ni含量对负载型NiO/ZnO-TiO2吸附剂结构及吸附脱硫性能的影响 被引量:2
9
作者 周广林 陈晟 +3 位作者 李芹 姜伟丽 周红军 龚学成 《燃料化学学报》 EI CAS CSCD 北大核心 2019年第8期987-992,共6页
以ZnO-TiO2为载体,采用等体积浸渍法制备了不同Ni含量的NiO/ZnO-TiO2汽油脱硫吸附剂。采用X射线衍射(XRD)、压汞、H2程序升温还原(H2-TPR)和H2程序升温脱附(H2-TPD)等手段对吸附剂进行了表征。同时,采用FCC轻汽油为原料,在固定床反应装... 以ZnO-TiO2为载体,采用等体积浸渍法制备了不同Ni含量的NiO/ZnO-TiO2汽油脱硫吸附剂。采用X射线衍射(XRD)、压汞、H2程序升温还原(H2-TPR)和H2程序升温脱附(H2-TPD)等手段对吸附剂进行了表征。同时,采用FCC轻汽油为原料,在固定床反应装置中对不同Ni含量的NiO/ZnO-TiO2吸附剂进行脱硫性能评价,以考察Ni含量对该吸附剂脱硫性能的影响。结果表明,Ni含量适量增加对于吸附剂比表面积、内部孔道分布和颗粒强度影响较小,同时能够增加具有脱硫活性的Ni0物种,促进吸附剂脱硫活性。当吸附剂中Ni质量分数达到5.48%后,吸附剂的内部孔道分布改变,吸附剂的比表面积和颗粒强度明显降低,对吸附剂脱硫活性极为不利。当Ni质量分数为4.45%时,吸附剂具有最佳脱硫性能,能够将FCC轻汽油中3×10^-4的总硫含量降低至5×10^-6以下,并维持脱硫时间达152 h,穿透硫容达11.24%(112.4 mg S/g吸附剂),且脱硫后FCC轻汽油烯烃含量变化较小。 展开更多
关键词 FCC轻汽油 脱硫吸附 ni/zno-TiO2 ni含量
下载PDF
Ni/ZnO吸附剂上汽油反应吸附脱硫本征动力学 被引量:3
10
作者 周红军 吴青 +3 位作者 毛存彪 张言斌 侯利国 周广林 《工业催化》 CAS 2015年第12期996-1001,共6页
采用小型固定床反应器,对制备的Ni/ZnO吸附剂的动力学进行测定,动力学实验基本条件为:以噻吩和正辛烷混合物作为模拟汽油,反应压力(0.4~0.8)MPa,反应温度(330~370)℃,氢油体积比70:1,空速5h-1。在消除吸附剂内、外扩... 采用小型固定床反应器,对制备的Ni/ZnO吸附剂的动力学进行测定,动力学实验基本条件为:以噻吩和正辛烷混合物作为模拟汽油,反应压力(0.4~0.8)MPa,反应温度(330~370)℃,氢油体积比70:1,空速5h-1。在消除吸附剂内、外扩散影响的备件下,通过设计正交实验,得到固定床反应条件下的动力学实验数据。根据幂函数型速率方程,对实验数据进行多元非线性拟合,得到动力学方程为:r=0.0229×e-22528.51/RTPH0.0013PS0.053C0.95ZnO,并对模型进行统计检验。结果表明,该模型对表面反应控制阶段具有较好的适用性。 展开更多
关键词 化学动力学 ni/zno吸附剂 反应吸附脱硫 本征动力学
下载PDF
焙烧温度对负载型NiO/ZnO-TiO_(2)吸附剂结构及吸附脱硫性能的影响 被引量:1
11
作者 周广林 刘飞 +3 位作者 李芹 陈晟 姜伟丽 龚学成 《中国石油大学学报(自然科学版)》 EI CAS CSCD 北大核心 2021年第3期160-165,共6页
采用等体积浸渍法制备NiO/ZnO-TiO_(2)汽油脱硫吸附剂,吸附剂前体通过不同温度焙烧得到成型吸附剂。考察焙烧温度对NiO/ZnO-TiO_(2)吸附剂脱硫活性的影响,并采用X射线衍射(XRD)、压汞、H_(2)程序升温还原(H_(2)-TPR)和H_(2)程序升温脱附... 采用等体积浸渍法制备NiO/ZnO-TiO_(2)汽油脱硫吸附剂,吸附剂前体通过不同温度焙烧得到成型吸附剂。考察焙烧温度对NiO/ZnO-TiO_(2)吸附剂脱硫活性的影响,并采用X射线衍射(XRD)、压汞、H_(2)程序升温还原(H_(2)-TPR)和H_(2)程序升温脱附(H_(2)-TPD)等手段对吸附剂进行表征。结果表明随焙烧温度升高,NiO与载体相互作用增强,活性组分NiO颗粒粒径增大,但TiO_(2)的存在一定程度上抑制了NiO迁移烧结;焙烧温度过高或过低都不利于吸附剂孔道形成,比表面积降低不利于脱硫过程;当焙烧温度为500℃时,吸附剂具有最大比表面积31.02 m^(2)/g,脱硫活性最佳,穿透时间和穿透硫容分别为152 h和11.21%。 展开更多
关键词 FCC轻汽油 脱硫吸附 ni/zno-TiO_(2) 焙烧温度
下载PDF
Ni/ZnO吸附剂反应吸附脱硫过程研究 被引量:1
12
作者 张冉冉 李永红 孔爱华 《应用化工》 CAS CSCD 2014年第7期1258-1262,共5页
对Ni/ZnO吸附剂脱除模拟汽油中噻吩硫的性能进行了评价,在温度400℃,压力1.0 MPa,液时空速(LHSV)60 h-1,氢气与模拟油的体积流量比为200(氢气体积为标准状态下的气体体积)条件下,Ni/ZnO吸附剂对硫含量为100μg/g的模拟汽油(A)和模拟汽油... 对Ni/ZnO吸附剂脱除模拟汽油中噻吩硫的性能进行了评价,在温度400℃,压力1.0 MPa,液时空速(LHSV)60 h-1,氢气与模拟油的体积流量比为200(氢气体积为标准状态下的气体体积)条件下,Ni/ZnO吸附剂对硫含量为100μg/g的模拟汽油(A)和模拟汽油(B)的穿透硫容分别达到360 mg-S/g-sorb和292 mg-S/g-sorb。通过实验测定了模型化合物在吸附剂上的吸附热,结果显示吸附热的高低顺序为:3-甲基噻吩﹥甲苯﹥2-甲基-2-丁烯﹥噻吩﹥2,3-二甲基-1-丁烯。两种模拟汽油中噻吩硫在吸附剂上吸附性能和吸附热的不同,均表明Ni/ZnO吸附剂与汽油中噻吩硫相互作用形成了S—M键而不是π络合键。 展开更多
关键词 反应吸附 脱硫 吸附热
下载PDF
Box-Behnken效应面法优化Ni/ZnO-SiO_2复合氧化物制备工艺及其吸附脱硫性能研究 被引量:1
13
作者 张玉婷 张景成 于海斌 《化学工程师》 CAS 2016年第3期77-79,共3页
利用响应曲面法对影响Ni/ZnO-SiO_2复合氧化物制备工艺的主要因素:活性金属组分比例、成胶pH值、老化时间进行试验设计。以Ni/ZnO-SiO_2复合氧化物用于低硫石脑油吸附脱硫处理中,产物硫含量为响应函数,建立相应的数学模型,优化试验方法... 利用响应曲面法对影响Ni/ZnO-SiO_2复合氧化物制备工艺的主要因素:活性金属组分比例、成胶pH值、老化时间进行试验设计。以Ni/ZnO-SiO_2复合氧化物用于低硫石脑油吸附脱硫处理中,产物硫含量为响应函数,建立相应的数学模型,优化试验方法。得到的最佳试验条件为:活性金属组分比例(Ni/Zn)为1.09、成胶pH值为5、老化时间为5h。此时Ni/ZnO-SiO_2复合氧化物对低硫石脑油的吸附脱硫性能为最优。Box-Behnke实验设计法用于Ni/ZnO-SiO_2复合氧化物制备工艺优化筛选是可行的,数学模型的预测值与实验观察值相符。 展开更多
关键词 响应曲面法 ni/zno-SiO_2复合氧化物 Box-Behnken实验设计 吸附脱硫
下载PDF
Ni/Al_2O_3-ZnO催化剂在FCC重汽油加氢脱砷的应用研究 被引量:1
14
作者 罗祥生 晁会霞 +2 位作者 刘子杰 刘承芷 庞周瑜 《钦州学院学报》 2018年第3期75-79,共5页
以馏程在100~224℃、砷含量350ng·g^(-1)的FCC重汽油为原料,以镍质量分数28~31%的负载型Ni/Al_2O_3-ZnO催化剂为活性中心,在100ml加氢装置上评价了催化剂的加氢脱砷性能。评价结果表明:在压力1.8MPa、温度120~160℃、氢油比40~80(v... 以馏程在100~224℃、砷含量350ng·g^(-1)的FCC重汽油为原料,以镍质量分数28~31%的负载型Ni/Al_2O_3-ZnO催化剂为活性中心,在100ml加氢装置上评价了催化剂的加氢脱砷性能。评价结果表明:在压力1.8MPa、温度120~160℃、氢油比40~80(v/v)、空速4.0~6.0h^(-1)条件下,FCC重汽油具有良好的深度脱砷性能并保持催化活性稳定性,稳定运转2000h后,加氢产品中砷含量仍小于10ng.g^(-1),脱砷的同时有少量的加氢脱硫和脱烯烃反应发生。 展开更多
关键词 FCC重汽油 加氢脱砷 负载型ni/Al2O3-zno催化剂 加氢脱硫
下载PDF
稀土对Ni-ZnO基脱硫催化剂反应性能的影响机制
15
作者 王鹏 邱丽美 +2 位作者 任奎 田辉平 龙军 《石油学报(石油加工)》 EI CAS CSCD 北大核心 2017年第3期411-418,共8页
为考察La、Ce对还原后的Ni-ZnO催化剂电子结构的调变作用,模拟工业条件对催化剂进行高压还原,对还原后的催化剂进行Ar离子刻蚀-XPS表征。结果表明,还原后的催化剂中以Ni 0为主,La不会被还原,Ce^(4+)被还原为Ce^(3+)。La^(3+)和Ce^(3+)... 为考察La、Ce对还原后的Ni-ZnO催化剂电子结构的调变作用,模拟工业条件对催化剂进行高压还原,对还原后的催化剂进行Ar离子刻蚀-XPS表征。结果表明,还原后的催化剂中以Ni 0为主,La不会被还原,Ce^(4+)被还原为Ce^(3+)。La^(3+)和Ce^(3+)在催化剂外表面富集,并与Ni之间存在相互作用,电子由Ni偏向La^(3+)和Ce^(3+),导致Ni的电子不饱和度增加,从而增强其对硫化物中孤对电子的吸附,使Ni-ZnO催化剂脱硫活性增强。但由于La、Ce与Ni-ZnO的电子配位结构存在明显差别,使用Ce改性的催化剂,在相同脱硫率下,汽油产品辛烷值较高;特别是当催化剂中Ce的质量分数为3.0%时,汽油的平均硫质量分数仅为5.1μg/g,与原料相比,研究法辛烷值增加0.3个单位。 展开更多
关键词 FCC汽油 加氢处理 脱硫 LA CE ni-zno
下载PDF
Ti掺杂对Ni/ZnO-TiO2吸附剂用于FCC轻汽油脱硫性能的影响 被引量:2
16
作者 陈晟 李芹 +3 位作者 王晓胜 龚学成 姜伟丽 周广林 《石油学报(石油加工)》 EI CAS CSCD 北大核心 2020年第2期388-395,共8页
采用混捏法制备了不同Ti含量的ZnO-TiO2载体,采用等体积浸渍法制备了NiO/ZnO-TiO2汽油脱硫吸附剂前驱体,并采用X射线衍射(XRD)、压汞、NH 3程序升温脱附(NH3-TPD)、H2程序升温还原(H2-TPR)和H2程序升温脱附(H2-TPD)等手段对其进行了表... 采用混捏法制备了不同Ti含量的ZnO-TiO2载体,采用等体积浸渍法制备了NiO/ZnO-TiO2汽油脱硫吸附剂前驱体,并采用X射线衍射(XRD)、压汞、NH 3程序升温脱附(NH3-TPD)、H2程序升温还原(H2-TPR)和H2程序升温脱附(H2-TPD)等手段对其进行了表征。以催化裂化轻汽油为原料,于氢气氛围下对NiO/ZnO-TiO2前驱体还原得到Ni/ZnO-TiO2吸附剂,在固定床上考察了Ti掺杂对该吸附剂脱硫性能的影响。结果表明:Ti的掺杂提高了Ni/ZnO吸附剂中活性组分Ni的分散度,增加了Ni活性位点,增强了吸附剂中强酸酸性及酸强度,Ti掺杂的吸附剂脱硫性能显著提高;Ti的掺杂能够减少游离Ni,有效抑制烯烃饱和;吸附剂脱硫性能随着Ti掺杂量的增加呈现先增强后减弱的趋势,当Ti掺杂质量分数为5%时,吸附剂具有最优脱硫性能,能够将FCC轻汽油中硫质量分数由300μg/g降低至5μg/g以下,穿透硫容为6.711%(每克吸附剂吸附硫67.11 mg),烯烃质量分数增加0.6百分点,降低了汽油辛烷值损失。 展开更多
关键词 FCC轻汽油 脱硫吸附剂 TIO2 ni/zno
下载PDF
AXAFS技术在Ni/ZnO吸附剂上模型油反应吸附脱硫机理研究中的应用
17
作者 张涛芝 黄礼春 +7 位作者 胡天斗 师瑞萍 王国富 郑黎荣 储胜启 周英丽 吴敏 安鹏飞 《燃料化学学报》 EI CAS CSCD 北大核心 2014年第2期246-251,共6页
原子X射线吸收精细结构(AXAFS)由吸收原子的外围束缚电子对出射光电子波的背散射引起,AXAFS信号与嵌入原子势能、原子间隙势能和吸收原子电子密度的分布密切相关,可以作为精确的探针来探测原子的电子化学结构。研究利用AXAFS技术,以Ni/... 原子X射线吸收精细结构(AXAFS)由吸收原子的外围束缚电子对出射光电子波的背散射引起,AXAFS信号与嵌入原子势能、原子间隙势能和吸收原子电子密度的分布密切相关,可以作为精确的探针来探测原子的电子化学结构。研究利用AXAFS技术,以Ni/ZnO脱硫吸附剂为研究对象,探讨了模型油在不同气体气氛下的脱硫反应机理。结果表明,在氢气气氛下、350℃和3.0MPa的条件下,从Zn元素的原位AXAFS谱图中可观察到脱硫过程中Zn元素的化学态变化。根据这些结果,揭示了氢气在脱硫过程中的重要作用,阐述了原位反应条件下吸附剂中Zn元素的化学态变化。 展开更多
关键词 AXAFS XAFS ni zno吸附剂 反应吸附脱硫 反应机理
下载PDF
Design and Development of Highly Efficient Ni/ZnO Catalysts Based on Semiconductor Metal Oxide Catalysis Theory
18
作者 Bian Yankun Kang Lei +3 位作者 Wu Feng Wang Haiyan Bai Yingzhi Sun Na 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS CSCD 2023年第2期33-40,共8页
In the context of reactive adsorption desulfurization,the development of an efficient Ni/ZnO desulfurizer has attracted increasing attention.In the work reported here,a novel Ni/Mn-ZnO composite nanowire desulfurizer ... In the context of reactive adsorption desulfurization,the development of an efficient Ni/ZnO desulfurizer has attracted increasing attention.In the work reported here,a novel Ni/Mn-ZnO composite nanowire desulfurizer is designed on the basis of the catalytic theory of semiconductor metal oxides and the characteristics of one-dimensional nanomaterials.X-ray diffraction,scanning electron microscopy,N_(2) adsorption-desorption,and X-ray photoemission spectroscopy demonstrate that Mn doping changes the crystal structure and morphology of the Ni/ZnO desulfurizer,increases the number of quasi-free electrons in the ZnO,and promotes H_(2)S adsorption.The Ni/Mn-ZnO composite nanowire desulfurizer exhibits good desulfurization performance when used with gasoline as the raw material. 展开更多
关键词 ni/zno NANOWIRE Mn desulfurization
下载PDF
大孔对ZnO/SiO_(2)复合脱硫剂常温脱硫性能的影响机制
19
作者 杨超 刘栩妃 +2 位作者 刘植龙 苏哲林 樊惠玲 《煤炭学报》 EI CAS CSCD 北大核心 2024年第6期2851-2859,共9页
煤化工行业作为我国主要的碳排放源,在双碳目标的约束下将面临巨大挑战。煤制气体精脱硫是煤炭高效清洁利用的重要组成部分,对于碳减排意义重大。氧化锌是目前普遍使用的干法精脱硫剂,但受动力学的限制,其在常温下的脱硫活性非常低,无... 煤化工行业作为我国主要的碳排放源,在双碳目标的约束下将面临巨大挑战。煤制气体精脱硫是煤炭高效清洁利用的重要组成部分,对于碳减排意义重大。氧化锌是目前普遍使用的干法精脱硫剂,但受动力学的限制,其在常温下的脱硫活性非常低,无法满足工业应用要求。孔扩散是氧化锌与H_(2)S反应发生的前提,但目前鲜有报道研究孔径,特别是大孔对脱硫性能的影响及影响机制。基于此,采用溶胶凝胶法和胶晶模板法分别制备了以介孔为主和以大孔为主的ZnO/SiO_(2)复合脱硫剂,探究了大孔结构的引入对其常温脱硫性能的影响。研究表明,尽管大孔的引入会增加脱硫剂的比表面积、强化表面碱性、提高氧化锌的分散性以及增加脱硫剂中氧空位浓度,但会导致脱硫剂脱硫性能大幅下降。介孔脱硫剂的穿透硫容为151.9 mg/g,是大孔脱硫剂的脱硫性能的2.3倍。这是因为大孔结构不稳定,在脱硫过程中易坍塌,阻碍了氧化锌反应位点的获取。气氛中的水汽在大孔表面不利于凝聚成水膜,进而抑制了脱硫反应的发生。更为重要的是,大孔制备过程中由于模板剂的燃烧会释放大量热,致使SiO_(2)网络发生深度交联,从而减小了脱硫剂中的介孔孔径。较小的介孔孔径导致其表面物理吸附水的量过多,进而抑制了氧化锌与H_(2)S的反应。 展开更多
关键词 zno/SiO_(2)复合脱硫剂 大孔结构 常温脱硫 水膜 吸附水
下载PDF
Pd-Ni/γ-Al_2O_3吸附剂的制备及其苯吸附脱硫性能研究 被引量:4
20
作者 姜洋 李倩 +2 位作者 李熙 侯莉 董森 《燕山大学学报》 CAS 北大核心 2019年第1期87-94,共8页
针对市售Pd吸附脱硫剂成本高、深度脱硫效果偏低的现状,本文以改性γ-Al_2O_3为载体,采用液相原位还原法制备出一种低成本、高脱硫能力的负载型三维纳米线网状结构的Pd-Ni吸附剂。利用XRD、TEM、SEM、BET等对样品的组成、结构和形貌进... 针对市售Pd吸附脱硫剂成本高、深度脱硫效果偏低的现状,本文以改性γ-Al_2O_3为载体,采用液相原位还原法制备出一种低成本、高脱硫能力的负载型三维纳米线网状结构的Pd-Ni吸附剂。利用XRD、TEM、SEM、BET等对样品的组成、结构和形貌进行表征,并利用催化剂评价装置和GC-MS考察了不同原子比的Pd-Ni/γ-Al_2O_3吸附剂对苯的脱硫效果。结果表明:Pd-Ni纳米线直径为4~5 nm,长达数微米,纳米线与Al_2O_3载体紧密结合,形成负载型三维网状结构吸附剂(活性组分质量分数为1%)。当Pd∶Ni原子比为1∶1时,经0.5 h吸附脱硫后可使苯原料中噻吩含量由300μg/L降至10μg/L以下,脱硫率达95%以上,是工业Pd/Al_2O_3(69.2%)的1.40倍,吸附剂中Pd的使用量约减少50%,极大降低了生产成本。本方法制备工艺简单,可控度高,为高效苯深度脱硫吸附剂的研发提供了理论依据和技术支持,具有重要的指导意义。 展开更多
关键词 液相原位还原 Pd-ni吸附剂 三维纳米线网状结构 脱硫率 苯深度脱硫
下载PDF
上一页 1 2 下一页 到第
使用帮助 返回顶部