Silica Gel Supported Trifluoromethanesulfonic Acid Catalyzed Beckmann Rearrangement of Cyclohexanone Oxime in Liquid Phase

The liquid phase Beckmann rearrangement of cyclohexanone oxime (CHO) using fuming sulfuric acid as a catalyst is a traditional method for preparing ε-caprolactam (CPL). This process has drawbacks, such as environmental pollution, corrosion of equipment, and low added value of by-product ammonium sulfate. This article designed and prepared a green silica gel-supported trifluoromethanesulfonic acid catalyst for the liquid-phase Beckmann rearrangement of CHO to prepare (CPL). The influencing factors of catalyst preparation and the optimal reaction conditions for Beckmann rearrangement were investigated. It was found that the optimal conditions for catalyst preparation were as follows: raw material silica gel:trifluoromethanesulfonic acid = 1:0.2 (mass ratio), room temperature, stirring time of 2.5 hours, and solvent of acetonitrile, silica gel mesh size is 100 - 200. The optimal reaction conditions for Beckmann rearrangement are CHO: catalyst = 1:2 (mass ratio), temperature of 130˚C, solvent of benzonitrile, volume of 30 mL/g CHO, and reaction time of 4 hours. Under the above conditions, the conversion of CHO is 90%, and the selectivity of CPL is 90%.

Gypsum-based Silica Gel Humidity-controlling Composite Materials:Preparation,Characterization,and Performance

Gypsum was used as substrate,and silica gel was mixed into substrate at a certain mass ratio to prepare humidity-controlling composites;moreover,the moisture absorption and desorption properties of gypsum-based composites were compared with adding different silica gel particle size and proportion.The morphological characteristics,the isothermal equilibrium moisture content curve,moisture absorption and desorption rate,moisture absorption and desorption stability,and humidity-conditioning performance were tested and analyzed.The experimental results show that,compared with pure-gypsum,the surface structure of the gypsum-based composites is relatively loose,the quantity,density and aperture of the pores in the structure increase.The absorption and desorption capacity increase along with the increase of silica gel particle size and silica gel proportion.When 3 mm silica gel particle size is added with a mass ratio of 40%,the maximum equilibrium moisture content of humidity-controlling composites is 0.161 g/g at 98% relative humidity(RH),3.22 times that of pure-gypsum.The moisture absorption and desorption rates are increased,the equilibrium moisture absorption and desorption rates are 2.68 times and 1.61 times that of pure-gypsum at 58.5% RH,respectively.The gypsum-based composites have a good stability,which has better timely response to dynamic humidity changes and can effectively regulate indoor humidity under natural conditions.

Preparation of Silica Gels with High Adsorption Activity for Extraction of Zirconium

Silica gels with a high specific surface area and high adsorption activity ,which have high selectivity and high adsorption capacity for zirconium in acidic high level radioactive liquid waste (HLLW), have been prepared from water-glass and hydrochloric acid through adding surfactants. The surfactant modifies the surface of the primary sol particles, thus suppresses the growth of the primary particle,but accelerates their agglomeration. The action of the surfactant is similar to that of the organic structure-directing agent and makes the sol cluster cross-linkage ring-like network in short order. The specific surface area of the silica gel is 998 m 2/g; the static adsorption capacity and the adsorption distribution coefficient for zirconium in HLLW are 32.6 mg/g and 56.1 mL/g, respectively.

Ni/ZrO_(2)-SO_(4)^(2-)催化剂的制备及其催化甲烷与CO_(2)制乙酸性能

以Zr(NO_(3))4·5H_(2)O和Ni(NO_(3))2·6H_(2)O为原料、(NH4)2CO_(3)为沉淀剂,采用溶胶凝胶-硫酸酸化两步法制备了Ni/ZrO_(2)-SO_(4)^(2-)催化剂,采用XRD,FTIR,SEM,N_(2)吸附-脱附,H_(2)-TPR,NH3-TPD等方法对Ni/ZrO_(2)-SO_(4)^(2-)催化剂进行表征,考察了Ni的引入方式对催化剂的结构和性能的影响。实验结果表明,与共沉淀方式引入Ni制备的Ni/ZrO_(2)-SO_(4)^(2-)催化剂相比,采用溶胶凝胶方式引入Ni制备的催化剂的四方相ZrO_(2)占比更高,表面酸量更多,且具有良好的热稳定性和较强的L酸性;采用溶胶凝胶方式引入Ni制备的Ni/ZrO_(2)-SO_(4)^(2-)催化剂的乙酸生成量明显优于共沉淀方式引入Ni制备的Ni/ZrO_(2)-SO_(4)^(2-)催化剂。四方相ZrO_(2)、酸性位点和过渡金属Ni之间的协同作用促进了甲烷与CO_(2)直接反应合成乙酸。

The Adsorption of Pb(II)Using Silica Gel Synthesized from Chemical Bottle Waste:Optimization Using Box-Behnken Design

The adsorption of Pb(II)on silica gel synthesized from chemical glass bottle waste has been studied.The effect of independent variables(adsorbent dose,initial concentration of Pb(II),contact time,and pH)on the Pb(II)removal from water was evaluated and optimized using the Response Surface Methodology(RSM).Under optimized conditions(adsorbent dose:20 mg;contact time:30 min;initial Pb(II)concentration:120 mg.L^(−1);and pH:8),the removal of Pb(II)was 99.77%.The adsorption equilibrium data obtained from the batch experiment were investigated using different isotherm models.The Langmuir isotherm model fits the experimental data.This shows that the surface of the silica gel synthesized from chemical bottles waste was covered by a Pb(II)monolayer.XRF analysis showed that the synthesized silica gel had a SiO_(2) content of 75.63%.Amorphous silica was observed from XRD analysis.SEM-EDX characterization showed that Pb was adsorbed on the silica gel surface.SEM analysis showed that silica gel has irregular particles with a surface area of 297.08 m2.g^(−1) with a pore radius of 15.74 nm calculated from BET analysis.

Silica Gel from Chemical Glass Bottle Waste as Adsorbent for Methylene Blue:Optimization Using BBD

This research focuses on the effective removal of methylene blue dye using silica gel synthesized from chemical glass bottle waste as an environmentally friendly and cost-effective adsorbent.The adsorption process was optimized using Box-Behnken Design(BBD)and Response Surface Methodology(RSM)to investigate the influence of pH(6;8 and 10),contact time(15;30 and 45 min),adsorbent mass(30;50 and 70 mg),and initial concentration(20;50 and 80 mg/L)of the adsorbate on the adsorption efficiency.The BBD was conducted using Google Colaboratory software,which encompassed 27 experiments with randomly assigned combinations.The silica gel synthesized from chemical glass bottle was characterized by XRD,FTIR,SEM-EDX and TEM.The adsorption result was measured by spectrophotometer UV-Vis.The optimized conditions resulted in a remarkable methylene blue removal efficiency of 99.41%.Characterization of the silica gel demonstrated amorphous morphology and prominent absorption bands characteristic of silica.The Langmuir isotherm model best described the adsorption behavior,revealing chemisorption with a monolayer coverage of methylene blue on the adsorbent surface,and a maximum adsorption capacity of 82.02 mg/g.Additionally,the pseudo-second-order kinetics model indicated a chemisorption mechanism during the adsorption process.The findings highlight the potential of silica gel from chemical glass bottle waste as a promising adsorbent for wastewater treatment,offering economic and environmental benefits.Further investigations can explore its scalability,regenerability,and reusability for industrial-scale applications.

Preparation of organically functionalized silica gel as adsorbent for copper ion adsorption

A novel adsorbent （AMPS-silica） was synthesized by bounding AMPS （2-acrylamido-2-methylpropanesulfonic acid） onto silica surface, which functioned with γ-methacryloxypropyltrimethoxysilane reagent. The adsorbent was characterized by nitrogen adsorption/desorption measurement, thermogravimetric analysis （TGA） and potentiometric titration analysis. The TGA result indicated that the surface modification reactions introduced some organic functional groups onto the surface of silica. The surface area of AMPSsilica was 389.7 m2/g. The adsorbent was examined for copper ion removal in series of batch adsorption experiments. Results showed that the adsorption of Cu2＋ onto AMPS-silica was pH dependent, and the adsorption capacity increased with increasing pH from 2 to 6. The adsorption kinetics showed that Cu^2＋ adsorption was fast and the data fitted well with a pseudo secondorder kinetic model. The adsorption of Cu^2＋ onto AMPS-silica obeyed both Freundlich and Langmuir isotherms, with r^2 = 0.993 and r^2 = 0.984, respectively. The maximum Cu^2＋ adsorption capacity was 19.9 mg/g. The involved mechanism might be the adsorption through metal binding with organic functional groups such as carboxyl, amino and sulfonic groups. Cu^2＋ loaded on AMPS-silica could be desorbed in HNO3 solution, and the adsorption properties remain stable after three adsorption-desorption cycles.

Separation and purification of deoxynivalenol(DON) mycotoxin from wheat culture using a simple two-step silica gel column chromatography

Deoxynivalenol（DON） is a type B trichothecenes mycotoxin produced by several Fusarium species, often found in foodstuffs for humans and animals. DON is in great demand for the toxicological researches both in vivo and in vitro. In this work, wheat culture was inoculated with a Fusarium graminearum PH-1 strain for DON production. The solvent system for crude extraction was acetonitrile-water（84：16, v/v）. A simple two-step silica gel column chromatography was employed to separate the DON mycotoxin from wheat culture, combined with preparative high performance liquid chromatography（preparative HPLC） to purify the compound. The solvent system for the second silica gel column chromatography was methylene chloride-methanol（17：1, v/v）, which provided a good elution effect selected on thin layer chromatography（TLC）. The target compound was identified by HPLC, and the chemical structure was confirmed by mass spectrometry（MS） and ~1H and ^（13）C nuclear magnetic resonance（NMR） spectroscopy. A total of 433 mg of purified DON was obtained from 1 kg of wheat culture, with a purity of 99.01%. The study had provided an easy-operating and cost-effective method to isolate an expensive compound in a simple way.

Ag-Ni/KCC-1的制备及其在草酸二甲酯加氢制乙醇酸甲酯中的催化性能

针对草酸二甲酯(DMO)加氢制备乙醇酸甲酯(MG)反应中,银(Ag)基催化剂成本较高、催化性能不稳定等问题,为降低成本并提高催化性能,以水热合成法制备的树枝状纤维形二氧化硅纳米球(KCC-1)为载体,采用等体积浸渍法制备Ag/KCC-1、Ag-Ni/KCC-1负载型催化剂。考察了Ag的较优负载量及总负载量不变时,Ag与镍(Ni)较佳的质量比。结果表明,Ag/KCC-1催化剂中,不同Ag负载量的催化剂,其结构和催化性能均有所不同,Ag负载量(质量分数)为15%时,性能较好;Ag-Ni/KCC-1催化剂中,适量Ni的引入对催化剂的结构和催化性能均有明显提高,当Ag和Ni的负载量分别为12%和3%时,催化性能较佳,与单组分负载的Ag/KCC-1催化剂相比,DMO转化率由90.37%提高至96.75%,MG转化率由90.77%提高至92.48%,MG收率由82.04%提高至89.47%。

Novel Silica Gel Supported Polyether Ionic Liquids: Efficient Catalysts Applied in Transformation of Carbon Dioxide

Three new catalysts based on the silica gel supported polyether ionic liquids(ILs), i.e., [HO-PECH-MIM]ClSi, [H2N-PECH-MIM]Cl-Si, and [HOOC-PECH-MIM]Cl-Si, were prepared, and their chemical structures were characterized by infrared(IR) spectroscopy and nuclear magnetic resonance(NMR) spectroscopy. Thermogravimetric analyzer(TG), X-ray diffractometer(XRD) and scanning electron microscope(SEM) were used to evaluate their thermal stability,crystalline structure and apparent morphology, respectively. Surface areas of the prepared catalysts were calculated by the Brunauer-Emmett-Teller(BET) method. The catalytic reaction for the synthesis of propylene carbonate(PC) using CO_2 and propylene oxide(PO) in the presence of the prepared catalysts was studied. The influences of times of recycling and catalyst structure on catalytic performance were also investigated. The experimental results showed that the silica gel supported polyether ILs catalysts successfully prepared under mild condition could possess the advantages of high activity, excellent thermal stability, good selectivity and easy recycling, while the phase transition of the liquid polyether ILs catalysts was also achieved. When the reaction temperature was 90 °C, the CO_2 pressure was 2.0 MPa and the dosage of the catalyst was 2.5%, [HOOC-PECH-MIM]Cl-Si was found to have the best catalytic performance in the catalytic process, with the conversion rate reaching 100% and the selectivity equating to 98.2%. The conversion rate and selectivity still could reach more than 90% even after the catalyst was reused for 15 times.

Mechanical Properties of Silica Aerogels Prepared from a Mixture of TEOS and Organo-alkoxysilanes of Type R_1SiX_3

Silica aerogels were prepared from a mixture of tetraethylorthosilicate and organo- alkoxysilanes. The effects of organo-alkoxysilanes on the mechanical properties of the silica aerogels were studied. The flexibility of silica aerogels was significantly improved by incorporation of organo-alkoxysilanes. When MTES and TEOS were combined as precursors of silica areogels, with the increased amount of MTES, the apparent elastic modulus and apparent compressive strength monotonously rose. At the same organo- alkoxysilanes to TEOS ratio, the size of alkyl groups of the organo-alkoxysilanes had little effect on the mechanical properties. In series of MTES and TEOS, the lowest elastic modulus of silica skeleton and the highest compressive strength of silica skeleton were observed at MTES to TEOS ratio of around 50：50. At a certain organo-alkoxysilanes to TEOS ratio, the elastic modulus of silica skeleton increased and the compressive strength of silica skeleton decreased with the size increase of the alkvl grouns.

Preparation and characterization of silica microcapsules containing butyl-stearate via sol-gel method

For thermal energy storage application in energy-saving building materials,silica microcapsules containing phase change material were prepared using sol-gel method in O/W emulsion system. In the system droplets in microns are formed by emulsifying an organic phase consisting of butyl-stearate as core material. The silica shell was formed via hydrolysis and condensation from tetraethyl silicate with acetate as catalyst. The SEM photographs show the particles possess spherical morphology and core-shell structure. The as-prepared silica microcapsules mainly consist of microsphere in the diameter of 3-7 μm and the median diameter of these microcapsules equals to 5.2 μm. The differential scanning calorimetry(DSC) curves indicate that the latent heat and the melting point of microcapsules are 86 J/g and 22.6 ℃,respectively. The results of DSC and TG further testify the microcapsules with core-shell structure.

Formation of macroporous gel morphology by phase separation in the silica sol-gel system containing nonionic surfactant

The phase separation and gel formation behavior in an alkoxy-derived silica sol-gel system containing C16EO15 has been investigated. Various gel morphologies similar to other sol-gel systems containing organic additives were obtained by changing the preparation conditions. Micrometer-range interconnected porous gels were obtained by freezing transitional structures of phase separation in the sol-gel process. The dependence of the resulting gel morphology on several important reaction parameters such as the starting composition, reaction temperature and acid catalyst concentration was studied in detail. The experimental results indicate that the gel morphology is mainly determined by the time relation between the onset of phase separation and gel formation.

Silica Gel Supported Hydrophobic Ionic Liquid for Selective Extraction and Determination of Coumarin

In this study, a modified silica gel surface with a hydrophobic ionic liquid (SG-1,10-PhenanNTf2) was used as an adsorbent for a selective extraction of coumarin prior to its determination by use of high performance liquid chromatography. Results demonstrated that SG-1,10-PhenanNTf2 phase had a good adsorption capacity up to 85.29 mg?g?1, high selectivity, good site accessibility and fast binding kinetics toward coumarin. The adsorption capacity for coumarin was improved by 62.33% with the SG-1,10-PhenanNTf2 phase as compared to activated silica gel. Adsorption isotherm data displayed that the adsorption process was mainly monolayer on a homogeneous adsorbent surface, confirming the validity of Langmuir adsorption isotherm model. The adsorption of coumarin on the SG-1,10-PhenanNTf2 phase was accomplished after only 60 min contact time. Results of kinetic models showed that the adsorption of coumarin on the SG-1,10-PhenanNTf2 phase obeyed a pseudo second-order kinetic model. Finally, the efficiency of this methodology was confirmed by applying it to real water samples.

Solid-Phase Aromatic Nitration with Mg(NO₃)₂on Silica Gel

Nitroaromatics are usually prepared using a mixed acid of nitric acid with strong acids. However, the use of strong acids caused dangerous work-up and the disposal of large amounts of acid-waste. Therefore, much effort has been made on the improvement of nitration process without strong acids. We examined solid-phase aromatic nitration with Mg(NO3)2 on silica gel in order to establish the nitration process without strong acids. The nitration of 1,2- and 1,3-, 1,4-dimethoxybenzenes and 4-methylanisole with Mg(NO3)2 proceeded by heating on silica gel at 150°C for 4 - 5 h to produce the nitroaromatics. The nitration of 1,3,5-trimethoxybenzene produced the nitrated dimer, 2,4,6,2’, 4’,6’-hexamethoxy-3-nitrobiphenyl, which was not isolated in other solid-phase nitration. In the cases of naphthalene derivatives, the α-nitrated compounds were obtained. In the cases of p-cresol and 2-naphthol, the esterification occurred at the hydroxyl group to give 4-tolyl nitrate and 2-naphthyl nitrate, respectively. It is synthetic interest to note that nitrate esters were isolated in solid phase. Thus Mg(NO3)2-SiO2 composite was mild reagent for solid-phase nitration. Acidity of Mg(NO3)2-SiO2 composite was determined to be pH 0.96 by the measurement of absorption spectra on a micro spectrophotometer using meso-tetra(p-cyanophenyl)porphyrin as a pH-indicator. Mg(NO3)2-SiO2 composite made acidic conditions. Therefore, it was suggested that Mg(NO3)2 reacted with proton on silica gel to form the NO+2. Thus, electron-rich aromatic hydrocarbons led the efficient nitration through electrophilic attack of NO+2. After the nitration, acidic Mg(NO3)2-SiO2 composite could be turned into neutrality by exposing wet conditions and disposed safely since the composite did not involve harmful elements. Thus the solid-phase nitration using Mg(NO3)2-SiO2 composite will provide safety and environmentally conscious chemical process.

Metal cation exchanged silica gel for identification of cationic and nonionic surfactants with preliminary separation by thin layer chromatography

Silica gel impregnated with 1% aqueous solutions of different metal cations （Li^＋, Mg^2＋, Zn^2＋, Cu^2＋, Co^2＋, Ni^2＋, Ba^2＋and Th^4＋） has been used for the analysis of nonionic and cationic surfaetants using simple aqueous acetone as mobile phase system. Co^2＋ was found the most suitable impregnant for the mutual separation of nonionic surfactants （Brij-35 and Brij-57） and cationic from nonionic surfactants （tetmdecyltrimethylammonium bromide and Cween-20）. Zinc sulphate impregnation （Zn^2＋-silica gel） shows identical chromatographic behavior and these layers are useful to separate nonionic surfactant （Brij-35） from cationic surfaetant （cetylpyridinium chloride）. The mutual separation of B J-35 and B J-57 is not influenced by the presence of optical brightener in the sample.

Effect of Catalyst on the Formation of Silica Coating on Nickel Substrate by Sol-Gel Processing

In this research work silica coating was produced on nickel substrates by a sol-gel process. In order to increase the rate of hydrolysis and to reduce the rate of polymerization several acid catalysts including nitric acid-hydrochloric acid, acetic acid, hydrochloric acid and nitric acid were add to silica sol. Conversely, in order to control the rate of hydrolysis and to increase the rate of polymerization, basic catalyst of ammonia and ammonia hydroxyl were introduced in to the solution. Nickel specimens of known surface roughness were chemically cleaned and prepared by dipping in the sols. In order to produce a suitable silica coating the drying and firing cycles were optimized on these substrates. The structure and uniformity of the coatings produced were examined by scanning electron microscopy. Coatings composition was determined using glow discharge optical spectroscopy and EDAX microanalysis. Experimental result showed that hydrochloric acid, acetic acid, ammonia and acetic acid - ammonia are suitable catalytic agents for silica coating formation on nickel type substrate.

Immobilization of Functionalized Ionic Liquid on Sol-Gel Derived Silica for Efficient Removal of H_2S

An innovative approach to H2 S capture has been developed using several metal-based ionic liquids([Bmim]Cl·CuCl_2, [Bmim]Cl·FeCl_3, [Bmim]Cl·ZnCl_2, [Bmim]Br·CuCl_2, and [Bmim]Br·FeCl_3) immobilized on the sol-gel derived silica, which is superior to purely viscous ionic liquid with a crucial limit of high temperature, low mass transfer rate,and mass loss. The adsorbents were characterized by the Fourier transform infrared spectrometer, transmission electron microscope, N_2 adsorption/desorption, X-ray photoelectron spectroscopy, and thermal analysis techniques. The effects of the metal and halogen in IL, the loading amount of IL, and the adsorption temperature were studied by dynamic adsorption experiments at a gas flow rate of 100 mL/min. The H2 S adsorption results have showed that the optimal adsorbent and adsorption temperature are 5% [Bmim]Cl·CuCl_2/silica gel and 20—50 ℃, respectively. H_2 S can be captured and oxidized to elemental sulfur, and [Bmim]Cl·CuCl_2/silica gel can be readily regenerated by air. The excellent efficiency of H2 S removal may be attributed to the formation of nano-scaled and high-concentration [Bmim]Cl·CuCl_2 confined in silica gel, indicating that the immobilization of [Bmim]Cl·CuCl_2 on the sol-gel derived silica can be used for H2 S removal promisingly.

A comparative study of drying techniques on the morphology of porous silica gels synthesized via sol-gel process

The effect of drying techniques on the microstructure,morphology and pore structure of porous silica gels was studied in the paper.The gels were prepared by using sol-gel process and different drying routes:freeze-drying (FD),low pressure drying (LPD),high temperature drying (HTD) and chemical modification & ambient drying (CMD) techniques.Observation under pore distribution and structural properties showed that CMD technique leads to homogenous mesoporous silica material with specific surface area of 745 m2/g,and the average pore size around 20 nm,while LPD and HTD result in loosely packed particles with non-isotropic aggregation pattern.The specific surface areas of LPD and HTD samples are 419 and 513 m2/g respectively,and the pore size distribution of the samples are observed distributing widely in range of 10-100 nm.Freeze drying method is a new but prospective way to prepare mesoporous silica.The specific area of FD sample is around 500 m2/g.By the comparison for the properties of the gels,this paper wants to induce a further interest in finding a proper method to synthesize the porous silica gels for low price use.

Selective removal of 2,4-dichlorophenoxyacetic acid from water by molecularly-imprinted amino-functionalized silica gel sorbent

A molecularly-imprinted amino-functionalized sorbent for selective removal of 2,4-dichlorophenoxyacetic acid （2,4-D） was prepared by a surface imprinting technique in combination with a sol-gel process. The 2,4-D-imprinted amino-functionalized silica sorbent was characterized by FT-IR, nitrogen adsorption and static adsorption experiments. The selectivity of the sorbent was investigated by a batch competitive binding experiment using an aqueous 2,4-D and 2,4-dichlorophenol （2,4-DCP） mixture or using an aqueous 2,4-D and 2,4- dichlorophenylacetic acid （DPAC） mixture. The largest selectivity coefficient for 2,4-D in the presence of 2,4-DCP was found to be over 18, the largest relative selectivity coefficient between 2,4-D and 2,4-DCP over 9. The static uptake capacity and selectivity coefficient of the 2,4-D-imprinted functionalized sorbent are higher than those of the non-imprinted sorbent. The imprinted functionalized silica gel sorbent offered a fast kinetics for the extraction/stripping of 2,4-D, 73% of binding capacity （200 mg/L 2,4-D onto 20 mg of imprinted sorbent） was obtained within 5 min and the adsorbed 2,4-D can be easily stripped by the mixture solution of ethanol and 6 mol/L HC1 （V：V =1：1）. In a test of five extraction/stripping cycles, the adsorption capacity of the sorbent was all above 93% of that of the fresh sorbent. Experimental result showed the potential of molecularly-imprinted amino-functionalized sorbent for selective removal of 2,4-D.