Anisotropy of mechanical properties of 2297-T87 Al–Li alloy thick plates

The tensile properties of 2297-T87 Al–Li alloy thick plates at different thickness position and in different direction were analyzed via tensile testing,optical microscopy(OM),X-ray diffraction(XRD),scanning electron microscopy(SEM),energy dispersive spectrometry(EDS),and transmission electron microscopy(TEM).Results indicated that the ultimate tensile strength(UTS)and yield strength(YS)of the alloy decreased firstly and then increased from the 1/8T position to the 1/2T position,whereas elongation to failure(Ef)decreased gradually such that its value along the rolling direction(RD)was higher than those along the transverse direction(TD)at the same thickness position.From the 1/8T position to the 3/8T position of the alloy,the UTS and YS along the TD were higher than those along the RD.At the 1/2T position of the alloy,the UTS,YS,and Ef along the RD were the highest,whereas those along the normal direction(ND)were the lowest.Microstructural observations further revealed that the anisotropy of tensile properties was related to grain morphology,crystal texture,second-phase particles,and Li atom segregation.

High-Performance 3D Li-B-C-Al Alloy Anode and its Twofold Li Electrostripping and Plating Mechanism Revealed by Synchrotron X-Ray Tomography

The uncontrollable Li electrostripping and plating process that results in dendritic Li growth and huge volume change of Li anode limits the practicality of Li metal batteries(LMBs).To simultaneously address these issues,designing three-dimensional(3D),lithiophilic and mechanically robust electrodes seems to be one of the cost-effective strategies.Herein,a new 3D Li-B-C-Al alloy anode is designed and fabricated.The prepared 3D alloy anode exhibits not only superior lithiophilicity that facilitates uniform Li nucleation and growth but also sufficient mechanical stability that maintains its structural integrity.Superior performance of the prepared 3D alloy is demonstrated through comprehensive electrochemical tests.In addition,non-destructive and 3D synchrotron X-ray computed tomography(SX-CT)technique is employed to investigate the underlying working mechanisms of the prepared alloy anode.A unique twofold Li electrostripping and plating mechanism under different electrochemical cycling conditions is revealed.Lastly,improved performance of the full cells built with the 3D alloy anode and LiNi_(0.8)Co_(0.1)Mn_(0.1)O_(2)(NCM811)cathode corroborate its potential application capability.Overall,the current work not only showcases the superiority of the 3D alloy as potential anode material for LMBs but also provides fundamental insights into its underlying working mechanisms that may further propel its research and development.

Impact Damage Identification of Aluminum Alloy Reinforced Plate Based on GWO-ELM Algorithm

As a critical structure of aerospace equipment,aluminum alloy stiffened plate will influence the stability of spacecraft in orbit and the normal operation of the system.In this study,a GWO-ELM algorithm-based impact damage identification method is proposed for aluminum alloy stiffened panels to monitor and evaluate the damage condition of such stiffened panels of spacecraft.Firstly,together with numerical simulation,the experimental simulation to obtain the damage acoustic emission signals of aluminum alloy reinforced panels is performed,to establish the damage data.Subsequently,the amplitude-frequency characteristics of impact damage signals are extracted and put into an extreme learning machine(ELM)model to identify the impact location and damage degree,and the Gray Wolf Optimization(GWO)algorithm is employed to update the weight parameters of the model.Finally,experiments are conducted on the irregular aluminum alloy stiffened plate with the size of 2200 mm×500 mm×10 mm,the identification accuracy of impact position and damage degree is 98.90% and 99.55% in 68 test areas,respectively.Comparative experiments with ELM and backpropagation neural networks(BPNN)demonstrate that the impact damage identification of aluminum alloy stiffened plate based on GWO-ELM algorithm can serve as an effective way to monitor spacecraft structural damage.

The study of electroless Ni-W-P alloy plating on glass fibers

Ni-W-P coatings were deposited on the surface of glass fibers by the electroless plating process. The bath was very stable through the palladium salt test. There was no phenomenon of peeling and blistering on the surface of the Ni-W-P alloy glass fibers in the thermal shock test. It showed that the deposit had high impact strength and good adhesion. The morphology of the coatings was observed by scanning electron microscope （SEM）. The elements and their contents were tested and analyzed by energy dispersion spectrometer （EDS）. The tungsten content reached up to 12.1 wt.%. The effects of the concentrations of NiSO4, Na2WO4, and NaH2PO2.H20 on the conductivity of the coatings were studied. The resistivity of the Ni-W-P alloy glass fibers reached 7.39 × 10^-3 Ωcm. The alloy coatings on glass fibers were analyzed by XRD. The results indicated that the deposit had an amorphous structure and good heat stability. The suitable work temperature range was lower than 190℃. Finally, the electromagnetic parameters of the Ni-W-P alloy glass fibers were tested and analyzed primarily. The magnetic loss reached 0.04023 and the dielectric loss reached -5.80239. The plated alloy is a kind of soft magnetic material.

Ageing behavior of an Al-Zn-Mg-Cu alloy pre-stretched thick plate

The ageing behavior of a pre-stretched thick plate of Al-Zn-Mg-Cu alloy was systemically studied including one-step ageing, two-step ageing, and retrogression and reageing treatment （RRA）. One-step ageing of the alloy resulted in peak ultimate tensile strengths of 595 and 575 MPa after 22 and 6 h at 120 and 135°C, respectively. The strengthening phase in peak aged （T6 temper） alloy contained GP zones and the η′ phase predominantly. After two-step ageing, the electrical conductivity was increased markedly, but the pre-stretched thick plate sacrificed a great loss of strength. RRA treatment provided a method for maintaining the strength close to that obtained by T6 temper and for obtaining the high electrical conductivity close to that obtained by T7 temper; the ultimate tensile strength and electrical conductivity were 583 MPa and 21.0 MS/m, respectively. TEM analysis of T7 and RRA specimens revealed two types of precipitates that contributed to age strengthening i.e. the η′ and η phases.

High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

Composition and Morphology of Zn-Co Alloy Coatings Deposited by Means of Pulse Plating Containing Reverse Current

The influence of bath constituents and pulse parameters on cobalt content, surface morphologies and grain size of Zn-Co alloy deposits was studied using a pulse plating technique with a square- wave current containing reverse pulse, It is found that Zn-Co alloy coatings obtained from the bath with the cobalt ion concentration over 60 wt% have a higher cobalt content in deposits. The results of pulse plating show that the average current density and reverse anodic current density amongst the variables investigated have very strong effects on the cobalt content in the Zn-Co alloy deposits. It is possible to electrodeposit Zn-Co alloy coatings with 10-90 wt% cobalt by modulating pulse parameters. The grain size, surface appearance and internal stress in the deposit were improved significantly by introducing the reverse current.

Effect of Heat Treatment on Structure and Magnetic Performance of Ni-Fe-P Alloy Obtained by Electroless Plating

The electroless deposition of Ni68-Fe10.5-P21.5 alloy has been investigated. The crystallization behavior of the deposit was comparatively studied by using differential scanning calorimetry and X-ray diffractometry. The deposit transforms into a square Ni3P phase at 380. 0 ℃, then changes into a cubic FeNi3 phase at 490. 0 ℃. The microhardness, the size of the formed grains and the magnetic performance of the deposit increase with the increase of the heat treatment temperature below 500 ℃, then they decrease after this temperature. The effect of heat treatment time at 500 ℃ on the surface micromorphology, the structure and the magnetic performance of the deposit were also studied. The resuits show that with the increase of heat treatment time, the extent of crystallization of the deposit increases and the size of the formed grains becomes uniform. The results also show that the magnetic performance of the deposit under heat treatment for 40 min is maximal and then decreases with the increase of heat treatment time. The property change of the deposit is related to the crystal structure and the size of the formed grains of the deposit.

STUDY ON THE RESPONSE TO LOW-VELOCITY IMPACT OF A COMPOSITE PLATE IMPROVED BY SHAPE MEMORY ALLOY

Improvement from the pseudo-elastic effect of shape memory alloy （SMA） on the low-velocity impact （LVI） resistance of a composite plate is investigated by the finite element method （FEM）. The stiffness matrix of the dynamic finite element equation is established step by step and the martensite fraction is obtained at each time step. The direct Newmark integration method is employed in solving the dynamic finite element equation, while the impact contact force is determined using the modified Hertz＇s law. It is found that SMA can effectively improve the performance of a composite structure subjected to low-velocity impact. Numerical results show that the deflection of a SMA-hybrid composite plate has been reduced approximately by thirty percent when the volume fraction of the embedded SMA reaches 0.3.

Transverse stress-strain evolution during welding of thin aluminum alloy plate

The FE simulation results of transverse stresses and strains during welding of thin aluminum alloy plate are presented. The results indicate that restraint condition is the main factor that determines whether or not hot cracking will occur. With rigid restraint hot cracking (crater cracking) will occur at the arc-stopping end, and such cracking usually will not occur without external restraint. But under restraint-free condition it is easy for terminal cracks to occur.

PRIMARY STUDY FOR THE TECHNOLOGY OF ELECTROLESS PLATING Fe-Al-P ALLOYS

Manuscript received 24 June 1999 The Fe Al P alloy deposits were plated on copper sheets by electroless plating. The change law of the deposition rate, composition, surface appearance and structure for the deposits was studied by changing the metallic salt ratios (AlCl 3/AlCl 3+FeSO 4), the concentration of metallic salt AlCl 3 and reductant NaH 2PO 2. The optimum plating bath was obtained. It was found that the choices of ligand and reductant were the key of increasing Al content for the deposits.

Nonlinear dynamic characteristics and optimal control of a giant magnetostrictive film-shaped memory alloy composite plate subjected to in-plane stochastic excitation

The nonlinear dynamic characteristics and optimal control of a giant magnetostrictive film （GMF）-shaped memory alloy （SMA） composite plate subjected to in-plane stochastic excitation are studied. GMF is prepared based on an SMA plate, and combined into a GMF-SMA composite plate. The Van der Pol item is improved to explain the hysteretic phenomena of GMF and SMA, and the nonlinear dynamics model of a GMF-SMA composite cantilever plate subjected to in-plane stochastic excitation is developed. The stochastic stability of the system is analyzed, and the steady-state probability density function of the dynamic response of the system is obtained. The condition of stochastic Hopf bifurcation is discussed, the reliability function of the system is provided, and then the probability density of the first-passage time is given. Finally, the stochastic optimal control strategy is proposed by the stochastic dynamic programming method. Numerical simulation shows that the stability of the trivial solution varies with bifurcation parameters, and stochastic Hopf bifurcation appears in the process; the system＇s reliability is improved through stochastic optimal control, and the first- passage time is delayed. A GMF-SMA composite plate combines the advantages of GMF and SMA, and can reduce vibration through passive control and active control effectively. The results are helpful for the engineering applications of GMF-SMA composite plates.

Low temperature bonding of LD31 aluminum alloys by electric brush plating Ni and Cu coatings

Soldering of LD31 aluminum alloys using Sn-Pb solder paste after electric brush plating Ni and Cu coatings was investigated. The technology of electric brush plating Ni and Cu was studied and plating solution was developed. The microstructure of the coatings, soldered joint and fracture face were analyzed using optic microscopy, SEM and EDX. The shear strength of soldered joint could reach as high as 26.83MPa. The results showed that reliable soldered joint could be obtained at 230℃, the adhesion of coatings and LD31 aluminum alloy substrate was high enough to bear the thermal process in the soldering.

Investigation on a Non-cyanide Plating Process of Ni-P Coating on Magnesium Alloy AZ91D

In this research we presented a non-cyanide plating process of Ni-P alloy coating on Mg alloy AZ91D. By applying a new process flow of electroless nickel plating in which zinc coating is used as transition of Ni-P coating on Mg alloy AZ91D, the process of copper transition coating plated in the cyanides bath can be replaced. A new bath composed of NiSO4 was established by orthogonal test. The results show that zinc transition coating can increase the adhesion and protect the Mg alloy substrate from the bath corrosion. The optimal plating bath composition is NiSO4·6H2O 20 g/L, NaH2PO2·H2O20g/L and C6H8O7·H2O 2.5 g/L, and optimal bath acidity and optimal plating temperature are pH 4.0 and 95℃, respectively. The present process flow is composed of ultrasonic cleaning→alkaline cleaning→acid pickling→activation→double immersing zinc→electroplating zinc→electroless nickel plating→passivation treatment. The present non-cyanide process of electroless nickel plating is harmless to our surroundings and Ni-P coating on Mg alloy AZ91D produced by present process possesses good adhesion and corrosion resistance.

Pulse Plating of Zn-Co Alloy Coatings

Pulse plating of Zn-Co alloys was studied using square pulse containing reverse current.The surface morphologies of Zn-Co alloy deposits were examined using scanning elecron microscopy （SEM）, and an attendant energy dispersive X-ray analyzer （EDA） was used to analyze the composition of Zn-Co alloy deposits. Results obtained showed that the average current density and reverse current density amongst all the variables investigated had very strong effects on the cobalt content and surface morphologies of Zn-Co alloy deposits. It is possible to elecrodeposit Zn-Co alloy coatings with a very wide cobalt content range of 10-90 wt% by modulating pulse parameters.

Electrochemical behavior of Cu-Zn-Al shape memory alloy after surface modification by electroless plated Ni-P

The electrochemical behavior of Cu-Zn-Al shape memory alloy (SMA) with andwithout electroless plated Ni-P was investigated by electrochemical methods, in artificial Tyrode'ssolution. The results showed that Cu-Zn-Al SMA engendered dezincification corrosion in Tyrode'ssolution. The anodic active current densities as well as electrochemical dissolution sensitivity ofthe electroless plated Ni-P Cu-Zn-Al SMA increased with NaCl concentration rising, pH of solutiondecreasing and environmental temperature uprising. X-ray diffraction analysis indicated that aftersurface modification by electroless plated Ni-P, an amorphous plated film formed on the surface ofCu-Zn-Al SMA. This film can effectively isolate matrix metal from corrosion media and significantlyimprove the electrochemical property of Cu-Zn-Al SMA in artificial Tyrode's solution.

Effect of electroless plating nickel treatment on electrode properties of Zr-based AB_2 type alloy

An electroless plating nickel treatment was processed to improve the active behaviors and discharge capacities of Zr based AB 2 alloys. The effects of the nickel coating on the surface appearance, the structure of the alloy powders and the electrode characteristics were investigated. It is found that the Ni rich layer formed through electroless plating nickel treatment plays an important role on the initial activation property and the discharge capacity of Zr based alloy. The optimal content of electroless plating nickel is about 15%, and the discharge capacity of the electrode can be increased to 400?mA·h·g -1 after 6 cycles. Although coated nickel is beneficial for quick activation and discharge capacity, excessive electroless plating nickel can result in a decreased discharge capacity.

Modified Layer-Removal Method for Measurement of Residual Stress in Pre-stretched Aluminium Alloy Plate

Residual stress is one of the factors affecting the machining deformation of monolithic structure parts in the aviation industry. Thus,the studies on machining deformation rules induced by residual stresses largely depend on correctly and efficiently measuring the residual stresses of workpieces. A modified layer-removal method is proposed to measure residual stress by analysing the characteristics of a traditional layer-removal method. The coefficients of strain release are then deduced according to the simulation results using the finite element method( FEM). Moreover,the residual stress in a 7075T651 aluminium alloy plate is measured using the proposed method,and the results are then analyzed and compared with the data obtained by the traditional methods. The analysis indicates that the modified layer-removal method is effective and practical for measuring the residual stress distribution in pre-stretched aluminium alloy plates.

Progress of electroplating and electroless plating on magnesium alloy

The current research processes of electroplating and electroless Ni-P alloy plating on magnesium alloys were reviewed. Theoretically,the reason for difficulties in electroplating and electroless plating on magnesium alloys was given.The zinc immersion, copper immersion,direct electroless Ni-P alloy plating and electroplating and electroless plating on magnesium alloys prepared by chemical conversion coating were presented in detail.Especially,the research development of magnesium alloy AZ91 and AZ31 was discussed briefly.Based on the analysis,the existing problems and future research directions were then given.

Variations of properties across plate thickness for Al alloy 7010

The variations of electrical conductivity and hardness across the thickness of an Al alloy 7010 plate under the temper condition T7651 were investigated. The electrical conductivity and hardness respond in a reciprocal manner. Cross-sectional slices of the plate subjected to re-solutionising/natural ageing and re-solutionising/artificial ageing show the similar tendencies in property changes as in the as-received raw material. This clearly suggests that the property inhomogeneity across the plate thickness is inherent of the manufacturing route. The differences in properties through the plate thickness are due to the changes in the concentrations of the strengthening alloying elements in the solid solution and the associated changes in microstructure; these are believed to be mainly due to the nature of plate solidification and prolonged high temperature during the rolling operation. The combination of electrical conductivity and hardness can be used as an integral quality property indicator for assessing inhomogeneity of thick products.