Developing high photocatalytic antibacterial Zn electrodeposited coatings through Schottky junction with Fe3+-doped alkalized g-C_(3)N_(4) photocatalysts

Pure Zn coatings easily lose their protective performance after biofouling because they have no antibacterial effect under visible light.In this study,we fabricate a new antibacterial Zn composite coating using electrodeposition to couple Fe3+-doped alkalized g-C_(3)N_(4)(AKCN-Fe)into an existing Zn coating and show that the AKCN-Fe enhances antibacterial property of the Zn coating under visible light.We attribute this enhancement to the high photocatalytic performance,high loading content,and good dispersion of AKCN-Fe.In addition,the photocatalytic antibacterial mechanism of the composite coating is supported by scavenger experiments and electron paramagnetic resonance(EPR)measurements,suggesting that superoxide(·O_(2)^(-))and hydroxyl radical(·OH)play main and secondary roles,respectively.

Fabrication and characterization of electrodeposited nanocrystalline Ni-Fe alloys for NiFe_2O_4 spinel coatings

Nanocrystalline Ni-Fe FCC alloy coatings with Fe content of 1.3%-39%（mass fraction） were fabricated on the nickel substrates using a DC electrodeposition technique. The crystal structure, lattice strain, grain size and lattice constant of the Ni-Fe alloy coatings were studied by X-ray diffraction technique. The chemical composition and surface morphology of the FCC Ni-Fe alloy coatings were investigated with the energy dispersive X-ray spectroscopy（EDS） and atomic force microscopy（AFM）. The results show that the Fe content of the Ni-Fe alloy coatings has a great influence on the preferred orientation, grain size, lattice constant and lattice strain. FCC Ni-Fe alloy coatings exhibit preferred orientations of（200） or（200）（111）. With an increase of Fe content, the preferred growth orientation of（200） plane is weakened gradually, while the preferred growth orientation of（111） increases. An increase of the Fe content in the range of 1.3%-25%（mass fraction） results in a significant grain refinement of the coatings. Increasing the Fe content beyond 25% does not decrease the grain size of FCC Ni-Fe alloys further. The lattice strain increases with increasing the Fe content in the FCC Ni-Fe alloys. Since the alloys with Fe content not less than 25% has similar grain size（~11 nm）, the increase in the lattice strain with the increase of Fe content cannot be attributed to the change in the grain size.

MICROSTRUCTURE OF ELECTRODEPOSITED Ni-W-P-SiC COMPOSITE COATINGS

ＭＩＣＲＯＳＴＲＵＣＴＵＲＥＯＦＥＬＥＣＴＲＯＤＥＰＯＳＩＴＥＤＮｉＷＰＳｉＣＣＯＭＰＯＳＩＴＥＣＯＡＴＩＮＧＳ①ＧｕｏＺｈｏｎｇｃｈｅｎｇ，ＹａｎｇＸｉａｎｗａｎ，ＬｉｕＨｏｎｇｋａｎｇＤｅｐａｒｔｍｅｎｔｏｆＭｅｔａｌｕｒｇｙ，Ｋｕｎｍｉｎ...

PROPERTIES OF ELECTRODEPOSITED AMORPHOUS Ni-W-P-SiC COMPOSITE COATINGS

The Effects of heat treatment temperature on the hardness,wear resistance and structure of the amorphous Ni-W-P-SiC composite coatings have been investigated.The results show that Ni-W-P-SiC composite coatings are amorphous under 300℃, partially crystalline at 300-400℃,and crystalline when heat treatment temperature reaches 400℃,the crystals being fine Ni3P phase particles.The hardness,wear resistance and the crystallization temperature of the composite coatings increase when an additive is added into the bath.The hardness and wear resistance of the coatings increase with increasing heat treatment temperature,and they will reach their peak values when the heat treatment temperature reaches 400℃.Corrosion experiment indicates that the corrosion resistance of amorphous Ni-W-P-SiC composite coatings in various kinds of corrosive media except nitric acid is better than that of stainless steel 1Cr18Ni9Ti.Scanning electron microscopy observation shows that the additive has no effect on the surface appearance of the coatings,but the current density and the pH value have considerable effects on the surface appearance.

STUDY ON PROPERTIES OF PULSE ELECTRODEPOSITED RE-Ni-W-P-SiC COMPOSITE COATINGS

The effects of pulse frequency f and duty cycle r on the deposition rate, composition, morphology, and hardness of pulse electrodeposited RE （rare earth）-Ni-W-P-SiC composite coatings have been studied. The results indicate that pulse current can improve the deposition rate of RE-Ni-W-P-SiC composite coatings; W, P, and SiC contents in the coating decrease with the increase of pulse frequency and reach the lowest value at f = 33Hz, whereas the RE content in the composite coatings increases with the increase of pulse frequency. SiC content decreases with the increase of duty cycle, W content reaches the lowest value, and P content reaches the highest value at r = 0.4; pulse current and RE can lead to smaller size of the crystalline grains; however, the effects of different pulse frequency and duty cycle on the morphologies of RE-Ni-W-P-SiC composite coatings are not obvious. The hardness of RE-Ni-W-P-SiC composite coatings is the highest when the duty cycle is at 0.6 and 0.8 and pulse frequency is at 50Hz. At the same pulse frequency, the hardness of RE-Ni-W-P-SiC composite coatings at r= 0.8 is higher than that at r= 0.6.

Corrosion resistance of electrodeposited RE-Ni-W-P-SiC composite coating

Immersion experiment results show that corrosion rate of the as deposited RE Ni W P SiC composite coating in HCl solutions increases with the rise of HCl concentration. On the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing HCl concentration. The corrosion rates of the composite coatings in as deposited state and after heat treatment in H 2SO 4 and H 3PO 4 solutions respectively decrease with the rise of H 2SO 4 and H 3PO 4 concentrations. The corrosion rate of the composite coating as deposited in FeCl 3 solutions decreases with increasing FeCl 3 concentration, while the rate of the composite coating after heat treatment increases with the rise of FeCl 3 concentration. The corrosion rate of 316L stainless steel in the corrosion media of H 2SO 4, HCl, H 3PO 4 and FeCl 3 solutions at different concentrations increases with rising concentration. In addition, the corrosion rate of 316L stainless steel in the corrosion media of H 2SO 4, HCl, H 3PO 4 and FeCl 3 solutions respectively is much greater than that of the RE Ni W P SiC composite coating as deposited and after heat treatment in the same corrosion media. [

Microstructure of electrodeposited RE-Ni-W-P-SiC composite coating

The components and microstructure of the RE Ni W P SiC composite coating were analyzed by means of EPXDS, SEM and XRD. The results showed that the composite coating containing 5%～14%RE, 4%～7%SiC, 12%～15%P and 5%～6%W was obtained by use of appropriate bath composition and plating conditions. The as deposited composite coating is amorphous and it becomes mixture when the temperature is raised from 200 ℃ to 400 ℃. However, the composite coating is crystal when the temperature is over 400 ℃. Scanning electron microscopy indicates that the heat treatment temperature has no effect on the surface morphologies of the RE Ni W P SiC composite coating. This is to say that the composite coating has a better heat stability of microstructure and high temperature oxidation.

Preparation and tribological performance of electrodeposited Ni-TiB_2-Dy_2O_3 composite coatings

TiB2 and Dy2O3 were used as codeposited particles in the preparation of Ni-TiB2-Dy2O3 composite coatings to improve its performance. Ni-TiB2-Dy2O3 composite coatings were prepared by electrodeposition method with a nickel cetyltrimethylammonium bromide and hexadecylpyridinium bromide solution containing TiB2 and Dy2O3 particles. The content of codeposited TiB2 and Dy2O3 in the composite coatings was controlled by adding TiB2 and Dy2O3 particles of different concentrations into the solution, respectively. The effects of TiB2 and Dy2O3 content on microhardness, wear mass loss and friction coefficients of composite coatings were investigated. The composite coatings were characterized by X-ray diffraction （XRD）, inductively coupled plasma-atomic emission spectrometer （ICP-AES） and scanning electron microscopy （SEM） techniques. Ni-TiBE-Dy2O3 composite coatings showed higher microhardness, lower wear mass loss and friction coefficient compared with those of the pure Ni coating and Ni-TiB2 composite coatings. The wear mass loss of Ni-TiB2-Dy2O3 composite coatings was 9 and 1.57 times lower than that of the pure Ni coating and Ni-TiB2 composite coatings, respectively. The friction coefficient of pure Ni coating, Ni-TiB2 and Ni-TiB2-Dy2O3 composite coatings were 0.723, 0.815 and 0.619, respectively. Ni-TiBE-Dy2O3 composite coatings displayed the least friction coefficient among the three coatings. Dy2O3 particles in composite coatings might serve as a solid lubricant between contact surfaces to decrease the friction coefficient and abate the wear of the composite coatings. The loading-bearing capacity and the wear-reducing effect of the Dy2O3 particles were closely related to the content of Dy2O3 particles in the composite coatings.

Thermodynamics of electrodeposited Ni-B-SiC composite coatings

The φ pH diagram of Ni B H 2O system was drawn, and the mechanism of electrodepositing Ni B SiC composite coatings was discussed. The results show that the deposition of Ni and B occurs prior to that of H 2 because of the over potential of H 2 evolution on the Fe substrate. Boron can not singly deposit in aqueous solution. Nickel and boron can co deposit in the form of Ni 4B 3 without evolution of hydrogen when the cathodical potential is kept to be -1.415 ～ -1.700?V.

Effect of sodium lauryl sulphate on microstructure, corrosion resistance and microhardness of electrodeposition of Ni-Co3O4 composite coatings

Ni?Co3O4 composite coatings were electrodeposited on mild steel surface from a Watts-type bath in the presence of sodium lauryl sulfate(SLS).The dispersed Co3O4 particles in the presence of SLS have a greater tendency to move towards cathode and get incorporated in the coating.SLS modifies chemical composition,surface morphology and microstructure of the Ni?Co3O4 composite coating.The developed composite coating exhibits higher corrosion resistance and microhardness than the pure nickel coating.The loadings of bath solution with different concentrations of Co3O4 particles in the presence of SLS provide hydrophobic nature to the coating surface,which is much effective in enhancing the corrosion resistance of Ni?Co3O4 composite coating.The agglomeration of Co3O4 particles(>3 g/L)under high bath load condition develops defects and dislocation on the coating surface,which results in lower corrosion resistance of the deposit.The mechanical properties of the hydrophobic coatings were assessed by the linear abrasion test.

Effect of Rare Earth on Microstructure and Corrosion Resistance of Pulse Reversal Current Electrodeposition Ni-Co Alloy Coatings

The effect of adding RE to plating bath on microstructure and corrosion resistance of Ni-Co alloy coatings prepared by pulse reversal current electrodeposition was studied by means of SEM/EDS, electrochemical analysis and corrosion mass loss etc. The results show that adding proper RE to plating solution can promote the microstructure of coatings compacter, the surface smoother and the crystal finer, and improve the corrosion resistance. The coatings exhibite the highest corrosion resistance when the concentration of RE reaches 0.25 g·L -1. The reason of increasing corrosion resistance by adding RE was also investigated.

Effects of ultrasonic dispersion on structure of electrodeposited Ni coating on AZ91D magnesium alloy

To obtain the refined electrodeposited nickel layer on AZ91D magnesium alloy,ultrasonic technology was applied in the processes of pre-treatment and electrodeposition.The phases of pre-treatment layer and the nickel coating were analyzed by X-ray diffractometry(XRD)and X-ray photoelectron spectroscopy(XPS),and the microstructure was observed by scanning electron microscopy(SEM).Then,the effects of ultrasonic dispersion on the microstructure of pre-treatment layer and the grain refinement of electrodeposited nickel layer were discussed.The results showed that the pre-treatment electrodeposited Cu-Sn layer with compact microstructure could be synthesized in alkaline copper-tin liquid with ultrasonic agitation,as a result,smooth and refined nickel coating formed on AZ91D magnesium alloy.On the other hand,preferred orientation in the coating decreased because of the refined grains.

Sliding wear behaviors of electrodeposited Ni composite coatings containing micrometer and nanometer Cr particles

Micrometer and nanometer Cr particles were co-deposited with Ni by electroplating from a nickel sulfate bath containing a certain content of Cr particles. Cr microparticles are in a size range of 1-5 μm and Cr nanoparticles have an average size of 40 nm. The friction and the wear performance of the co-deposited Ni-Cr composite coatings were comparatively evaluated by sliding against Si3N4 ceramic balls under non-lubricated conditions. It is found that the incorporation of Cr particles enhances the microhardness and wear resistance of Ni coatings. The wear resistance of Ni composite coating containing Cr nanoparticles is higher than that of the Ni composite coating containing Cr microparticles with a comparable Cr particle content. The co-deposition of smaller nanometer Cr particles with Ni effectively reduces the size of Ni crystals and significantly increases the hardness of the composite coatings due to grain-refinement strengthening and dispersion-strengthening,resulting in a significant improvement of wear resistance of the Ni-Cr nanocomposite coatings.

Structure and characteristics of electrodeposited RE-Ni-W-P-B_4C-PTFE composite coatings

Hardness, friction and wear characteristics of electrodeposited RE Ni W P B 4C PTFE composite coatings were studied, and the reason for these fine characteristics was explained in respect of structure. The results show that 1) the structure of RE Ni W P B 4C PTFE composite coatings experiences a transformation process from amorphous to mixture then to crystal as the heat treatment temperature rises; 2) incorporating of B 4C greatly increases the hardness of the coating; 3) the wear resistance of the coating is best with heat treatment for 1?h at 300?℃, which is greatly superior to that of the other traditional coatings.

Effects of pulse current on properties of electrodeposited RE-Ni-W-P-SiC composite coating

Effects of pulse current on properties of electrodeposited RE-Ni-W-P-SiC composite coating were studied. The results show that hardness of the pulse current electrodeposited composite coatings is higher than that of the direct current electrodeposited composite coatings while other parameters are the same. Otherwise, the deposited velocity is higher, and wear resistance and corrosion resistance of the pulse current electrodeposited composite coatings are also improved when the average current density is 10 A/dm2 , pulse frequency is 800 Hz and duty ratio is 1: 5. The hardness of the coating as-deposited is HV500 - 700, and it reaches HV1300 after heat treatment at 400 ℃ for 1 h.

Characteristics of electrodeposited RE-Ni-W-B-B_4C-MoS_2 composite coating

The high temperature oxidation resistance of RE Ni W B B 4C MoS 2 composite coating, the effects of electrodeposition conditions on the morphologies of the coating and the effect of heat treatment temperature on its hardness, abrasion resistance and phase structure were investigated by using scanning electron microscope(SEM), X ray diffractometer, microhardness tester and abrasion machine. The results show that the oxidation degree of RE Ni W B B 4C MoS 2 composite coating is small when the temperature is lower than 700 ℃, but it increases sharply when the temperature is higher than 700 ℃. The hardness of RE Ni W B B 4C MoS 2 composite coating increases with increasing heat treatment temperature, it comes up to the maximum value at 400 ℃,but it decreases gradually if the temperature rises continuously. The most favourable abrasion resistance was attained after RE Ni W B B 4C MoS 2 composite coating being heat treated at 400 ℃. Without heat treating, it is mainly amorphous and partially crystallized, but wholly crystallized after being heat treated at 500 ℃. RE in the composite coating is in the form of CeO 2 and additions of CeO 2 and B 4C can enhance the thermostability of RE Ni W B B 4C MoS 2 composite coating.

Effect of Y_2O_3 on microstructure and oxidation of γ-Ni+γ′-Ni_3Al coatings transformed from electrodeposited Ni-Al films at 1000℃

The electrodeposited Y2O3-dispersedγ-Ni+γ′-Ni3Al coatings on Ni substrates were developed by the conversion of electrodeposited Ni-Al-Y2O3 films with dispersed Al microparticles in Ni matrix into Ni3Al by vacuum annealing at 800℃for 3 h. For comparison,Y2O3-freeγ-Ni+γ′-Ni3Al coatings with a similar Al content were also prepared by vacuum annealing the electrodeposited microparticle-dispersed composite coatings of Ni-Al under the same condition.SEM and TEM characterizations show that the electrodeposited Y2O3-dispersedγ+γ′coatings exhibit finer grains,a more homogeneous distribution ofγ′,and a narrowedγ′phase spacing compared with the electrodeposited Y 2 O3-freeγ+γ′coatings.The oxidation at 1 000℃shows that the addition of Y2O3 significantly improves the oxidation resistance of the electrodepositedγ+γ′coatings.The effect of Y2O3 particles on the microstructure and oxidation behavior of the electrodepositedγ+γ′coatings was discussed in detail.

Micromorphology and texture of niobium coating electrodeposited in NaCl−KCl−CsCl molten salt system

A low-toxicity and environment-friendly NaCl−KCl−CsCl−K_(2)NbF_(7) system was used to prepare Nb coatings on Mo substrates.The effects of temperature,current density and electrodeposition time on the micromorphologies and textures of the electrodeposited Nb coatings were studied.The results showed that Nb coatings obtained at 30−70 mA/cm^(2) in the temperature range of 700−750℃ were continuous and compact,with a hardness range of 2.16−2.45 GPa.As the columnar crystals grew with time,the preferential growth orientations of the Nb coatings changed from<200>to<211>and then became disordered.With increasing polarization,the morphologies of the Nb coatings changed from hexagonal star-like surface to conical or pyramid-like surface.

Electrodeposition of Ni-Co-Fe_2O_3 composite coatings

Ni-Co-Fe2O3 composite coatings were electrodeposited using cetyltrimethylammonium bromide(CTAB)-modified Watt's nickel bath with Fe2O3 particles dispersed in it.The effects of the plating parameters on the chemical composition,structural and morphological characteristics of the electrodeposited Ni-Co-Fe2O3 composite coatings were investigated by energy dispersive X-ray(EDS) spectroscopy,X-ray diffractometry(XRD) and scanning electron microscopy(SEM).The results reveal that Fe2O3 particles can be codeposited in the Ni-Co matrix.The codeposition of Fe2O3 particles with Ni-Co is favoured at high Fe2O3 particle concentration and medium stirring,and the deposition of Co is favoured at high concentration of CTAB.Moreover,the study of the textural perfection of the deposits reveals that the presence of particles leads to the worsening of the quality of the observed <220> preferred orientation.Composites with high concentration of embedded particles exhibit a preferred crystal orientation of <111>.The more the embedded Fe2O3 particles in the metallic matrix,the smaller the sizes of the crystallite for the composite deposits.

Effect of tension deformation on microstructure and mechanism of electrodeposited nickel coating

Nickel coating deposits with better ductility on a lower carbon steel sheet were produced by electrodeposition method and the electrodeposited nickel coating was deformed with the strain of 10%. Then the surface morphology,the deformation texture and the mechanical properties were analyzed by scanning electron microscopy(SEM),X-ray diffractometry(XRD) and nano-indentation measurement,respectively. The principle of nano-indentation to measure the hardness and elastic modulus of nickel coating was introduced. The relation curves of the load and displacement were obtained,including the original electrodeposited samples and the samples under tension. The results show that:1) there are only two main texture components Ni(111) and Ni(200) in the nickel coating,and no new texture component is found due to the elongation;2) after tensile deformation in the coating,the surface roughness increases and the microcrack is found;3) The hardness and the elastic modulus decrease after tensile deformation;and 4) for the original electrodeposited sample,the indentation depths change with the load,the hardness and the elastic modulus decrease with the increase of the depth. In addition,the investigation of creep shows that the value of creep increases when the tensile strain ε>10%.