Electroless plating and growth kinetics of Ni-P alloy film on SiC_p/Al composite with high SiC volume fraction

After Sn/Pd activating, the SiCp/Al composite with 65% SiC (volume fraction) was coated by electroless Ni?P alloy plating. Surface morphology of the composite and its effect on the Ni?P alloy depositing process and bonding action of Ni and P atoms in the Ni?P alloy were studied. The results show that inhomogeneous distribution of the Sn/Pd activating points results in preferential deposition of the Ni?P alloy particles on the Al alloy and rough SiC particle surfaces and in the etched caves. The Ni?P alloy film has an amorphous structure where chemical bonding between Ni and P atoms exists. After a continuous Ni?P alloy film formed, electroless Ni?P alloy plating is not affected by surface morphology and characteristics of the SiCp/Al composite any longer, but by the electroless plating process itself. The Ni?P alloy film follows linear growth kinetics with an activation energy of 68.44 kJ/mol.

High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

Effects of the Composition of Electrodeposited Fe-Ni-P Alloy on the Thermostability and Magnetic Properties

The magnetic properties, structure defects of electrodeposited Fe-Ni-P alloys with various compositions and the thermostability at amorphous state have been studied by DSC, positron annihilation and electronic integrating instrument methods. The results show that the thermostability of amorphous Fe-Ni-P alloys increases with Fe content. Emergence and recrystallization of stable phases defer as the P content of the coating increases. The minimum H-c, B-r and P-h occur at 9.4 P (wt pet) content. Maximum H-c, B-r and P-h occur at the weight ratio of Fe to Ni equaling to 1/9.

TEMPERATURE DEPENDENCE UPON VISCOSITY OF Ni-P ALLOY ON AMORPHOUS FORMATION

The viscous flow of amorphous alloys near T_gis closely related to the viscosity of liquid alloys. On the basis of the measured surface tension and density for Ni-P binary alloys,the correla- tion between the viscosity of the melt and viscous flow process of the amorphous alloy is inves- tigated.The relationship between viscosity and temperature for Ni-P alloys going from liquid to amorphous solid may be described by the following formula:

EFFECT OF PRE-ANNEALING ON CRYSTALLIZATION KINETICS OF AMORPHOUS Ni-P ALLOYS

The effect of pre-annealing treatment on the crystallization kinetics parameters of amorphous Ni-P alloys has been investigated.Experimental results showed that the crystallization tem- perature,T_p and T_x,the apparent activation energy,E_c,as well as the Avrami exponent for isothermal crystallization,n,decrease significantly,while ΔT_(px)=T_p-T_x increases with the elongation of pre-annealing time at 570 K.

Researches on Ni-P Alloys

Worldwide researches on Ni-P alloys have been briefly reviewed,including their corrosion resistance, crystallisation behaviour,amorphisation by ion implantation,and usage as underlayer for thin film magnet- ic media.

TWIP钢表面Ni-P化学镀层组织结构及性能研究

目的在孪生诱发塑性钢(TWIP)表面制备Ni-P镀层,提高TWIP钢的耐腐蚀性能。方法通过化学镀工艺在TWIP钢表面制备了高磷Ni-P镀层,并进行不同温度的热处理,利用扫描电镜及能谱仪、X射线衍射仪及原子力显微镜等探究了热处理温度和时间对Ni-P镀层形貌和组织结构的影响。通过电化学方法研究了TWIP钢表面镀层的耐蚀性能。结果随着热处理温度的升高,镍磷原子发生迁移,胞状组织边界模糊,粗糙度降低,其中600℃热处理镀层表面最为致密平整。随着热处理温度的升高,镀层组织结构演变过程如下:非晶态(普通镀层)→非晶态部分晶化,Ni12P5、Ni5P2等亚稳态镍磷化合物析出(300℃)→非晶态完全晶化、稳态Ni3P相长大(400℃)→晶粒长大(500℃、600℃)。Ni-P镀层能够明显提升TWIP钢的耐腐蚀性能。随着热处理温度的升高,镀层的耐蚀性能先降低后升高。600℃热处理1h镀层的腐蚀电流密度为0.25μA/cm^(2),与普通Ni-P镀层相比降低了80.9%,与TWIP钢基体相比降低了99.6%。600℃热处理镀层光滑致密无缺陷的表面促进了保护性氧化膜的产生,使镀层的耐蚀性能提高。结论合适的热处理工艺提高了Ni-P镀层的致密性和保护能力,光滑致密无缺陷的镀层能够为TWIP钢提供良好的防护。

化学镀Ni-P/Sn2.5Ag0.7Cu0.1RE微连接焊点热时效过程组织与性能

为探究化学镀Ni-P无铅焊点在热时效作用下的组织与性能,采用化学镀方法在T2紫铜表面制备Ni-P层,使用Sn_(2.5)Ag_(0.7)Cu_(0.1)RE钎料通过回流焊方法制备化学镀Ni-P无铅焊点。结果表明:微焊点Ni-P/钎缝过渡区域金属间化合物(IMC)初始组织为呈块状的(Ni,Cu)_(3)Sn_(4),平均厚度为1.5μm。在180℃条件下时效100 h过程中,微焊点Ni-P/钎缝过渡区(Ni,Cu)_(3)Sn_(4)IMC形貌逐渐转变为层状并增厚至3.3μm,微焊点剪切断裂位置由钎缝处向Ni-Sn-P/IMC交界处转移,断裂方式由韧性断裂转变为脆性断裂,相应微焊点的推剪力由初始的16 N下降11.9%。

低浓度硫酸铜对化学镀Ni-P镀层微观结构及性能的影响

为改善镍磷(Ni-P)镀层的表面质量、提高Ni-P镀层的性能,在化学镀Ni-P镀液中加入少量的硫酸铜(CuSO_(4)·5H_(2)O)制备Ni-P镀层。利用扫描电镜、能谱仪、X射线衍射仪分析了镀层的表面形貌、成分和结构,研究了CuSO_(4)·5H_(2)O浓度对镀层的微观结构、表面粗糙度、光泽度、硬度、耐磨性和耐蚀性的影响。研究表明:当CuSO_(4)·5H_(2)O浓度为0.1 g/L时,镀层为致密的非晶态节瘤状组织,具有最佳的耐蚀性;当CuSO_(4)·5H_(2)O浓度为0.2 g/L时,镀层表面质量最好,硬度高、耐磨性优异,但镀层中出现少量微晶态Ni-Cu固溶体,耐蚀性下降;当CuSO_(4)·5H_(2)O浓度超过0.2 g/L后,镀层为混晶态菜花状组织,镀层表面的质量和耐蚀性随CuSO_(4)·5H_(2)O浓度的增加不断恶化。

Accelerated design of high-performance Mg-Mn-based magnesium alloys based on novel bayesian optimization

Magnesium(Mg),being the lightest structural metal,holds immense potential for widespread applications in various fields.The development of high-performance and cost-effective Mg alloys is crucial to further advancing their commercial utilization.With the rapid advancement of machine learning(ML)technology in recent years,the“data-driven''approach for alloy design has provided new perspectives and opportunities for enhancing the performance of Mg alloys.This paper introduces a novel regression-based Bayesian optimization active learning model(RBOALM)for the development of high-performance Mg-Mn-based wrought alloys.RBOALM employs active learning to automatically explore optimal alloy compositions and process parameters within predefined ranges,facilitating the discovery of superior alloy combinations.This model further integrates pre-established regression models as surrogate functions in Bayesian optimization,significantly enhancing the precision of the design process.Leveraging RBOALM,several new high-performance alloys have been successfully designed and prepared.Notably,after mechanical property testing of the designed alloys,the Mg-2.1Zn-2.0Mn-0.5Sn-0.1Ca alloy demonstrates exceptional mechanical properties,including an ultimate tensile strength of 406 MPa,a yield strength of 287 MPa,and a 23%fracture elongation.Furthermore,the Mg-2.7Mn-0.5Al-0.1Ca alloy exhibits an ultimate tensile strength of 211 MPa,coupled with a remarkable 41%fracture elongation.

Relationship between the unique microstructures and behaviors of high-entropy alloys

High-entropy alloys(HEAs),which were introduced as a pioneering concept in 2004,have captured the keen interest of nu-merous researchers.Entropy,in this context,can be perceived as representing disorder and randomness.By contrast,elemental composi-tions within alloy systems occupy specific structural sites in space,a concept referred to as structure.In accordance with Shannon entropy,structure is analogous to information.Generally,the arrangement of atoms within a material,termed its structure,plays a pivotal role in dictating its properties.In addition to expanding the array of options for alloy composites,HEAs afford ample opportunities for diverse structural designs.The profound influence of distinct structural features on the exceptional behaviors of alloys is underscored by numer-ous examples.These features include remarkably high fracture strength with excellent ductility,antiballistic capability,exceptional radi-ation resistance,and corrosion resistance.In this paper,we delve into various unique material structures and properties while elucidating the intricate relationship between structure and performance.

Microstructure and damping properties of LPSO phase dominant Mg-Ni-Y and Mg-Zn-Ni-Y alloys

This work studied the microstructure,mechanical properties and damping properties of Mg_(95.34)Ni_(2)Y_(2.66) and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys systematically.The difference in the evolution of the long-period stacked ordered(LPSO)phase in the two alloys during heat treatment was the focus.The morphology of the as-cast Mg_(95.34)Ni_(2)Y_(2.66)presented a disordered network.After heat treatment at 773 K for 2 hours,the eutectic phase was integrated into the matrix,and the LPSO phase maintained the 18R structure.As Zn partially replaced Ni,the crystal grains became rounded in the cast alloy,and lamellar LPSO phases and more solid solution atoms were contained in the matrix after heat treatment of the Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloy.Both Zn and the heat treatment had a significant effect on damping.Obvious dislocation internal friction peaks and grain boundary internal friction peaks were found after temperature-dependent damping of the Mg_(95.34)Ni_(2)Y_(2.66)and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys.After heat treatment,the dislocation peak was significantly increased,especially in the alloy Mg_(95.34)Ni_(2)Y_(2).66.The annealed Mg_(95.34)Ni_(2)Y_(2.66)alloy with a rod-shaped LPSO phase exhibited a good damping performance of 0.14 atε=10^(−3),which was due to the difference between the second phase and solid solution atom content.These factors also affected the dynamic modulus of the alloy.The results of this study will help in further development of high-damping magnesium alloys.

High corrosion and wear resistant electroless Ni–P gradient coatings on aviation aluminum alloy parts

A Ni–P alloy gradient coating consisting of multiple electroless Ni–P layers with various phosphorus contents was prepared on the aviation aluminum alloy. Several characterization and electrochemical techniques were used to characterize the different Ni–P coatings’ morphologies, phase structures, elemental compositions, and corrosion protection. The gradient coating showed good adhesion and high corrosion and wear resistance, enabling the application of aluminum alloy in harsh environments. The results showed that the double zinc immersion was vital in obtaining excellent adhesion (81.2 N). The optimal coating was not peeled and shredded even after bending tests with angles higher than 90°and was not corroded visually after 500 h of neutral salt spray test at 35℃. The high corrosion resistance was attributed to the misaligning of these micro defects in the three different nickel alloy layers and the amorphous structure of the high P content in the outer layer. These findings guide the exploration of functional gradient coatings that meet the high application requirement of aluminum alloy parts in complicated and harsh aviation environments.

Influence of heat treatment on microstructure,mechanical and corrosion behavior of WE43 alloy fabricated by laser-beam powder bed fusion

Magnesium(Mg)alloys are considered to be a new generation of revolutionary medical metals.Laser-beam powder bed fusion(PBF-LB)is suitable for fabricating metal implants withpersonalized and complicated structures.However,the as-built part usually exhibits undesirable microstructure and unsatisfactory performance.In this work,WE43 parts were firstly fabricated by PBF-LB and then subjected to heat treatment.Although a high densification rate of 99.91%was achieved using suitable processes,the as-built parts exhibited anisotropic and layeredmicrostructure with heterogeneously precipitated Nd-rich intermetallic.After heat treatment,fine and nano-scaled Mg24Y5particles were precipitated.Meanwhile,theα-Mg grainsunderwent recrystallization and turned coarsened slightly,which effectively weakened thetexture intensity and reduced the anisotropy.As a consequence,the yield strength and ultimate tensile strength were significantly improved to(250.2±3.5)MPa and(312±3.7)MPa,respectively,while the elongation was still maintained at a high level of 15.2%.Furthermore,the homogenized microstructure reduced the tendency of localized corrosion and favoredthe development of uniform passivation film.Thus,the degradation rate of WE43 parts was decreased by an order of magnitude.Besides,in-vitro cell experiments proved their favorable biocompatibility.

An ionic liquid-assisted strategy for enhanced anticorrosion of low-energy PEO coatings on magnesium–lithium alloy

A low-energy plasma electrolytic oxidation(LePEO)technique is developed to simultaneously improve energy efficiency and anti-corrosion.Ionic liquids(1-butyl-3-methylimidazole tetrafluoroborate(BmimBF_(4)))as sustainable corrosion inhibitors are chosen to investigate the corrosion inhibition behavior of ionic liquid(ILs)during the LePEO process for LA91 magnesium-lithium(Mg-Li)alloy.Results show that the ionic liquid BmimBF_(4)participates in the LePEO coating formation process,causing an increment in coating thickness and surface roughness.The low conductivity of the ionic liquid is responsible for the voltage and breakdown voltage increases during the LePEO with IL process(LePEO-IL).After adding BmimBF_(4),corrosion current density decreases from 1.159×10^(−4)A·cm^(−2)to 8.143×10^(−6)A·cm^(−2).The impedance modulus increases to 1.048×10^(4)Ω·cm^(−2)and neutral salt spray remains intact for 24 h.The superior corrosion resistance of the LePEO coating assisted by ionic liquid could be mainly attributed to its compact and thick barrier layer and physical absorption of ionic liquid.The ionic liquid-assisted LePEO technique provides a promising approach to reducing energy consumption and improving film performance.

Revealing the role of pyramidal slip in the high ductility of Mg-Li alloy

The high ductility of Mg-Li alloy has been mainly ascribed to a high activity of pyramidal<c+a>slip to accommodate plastic strain.In the present study,however,a quantitative analysis reveals that Li-addition can only slightly stimulate the activation of pyramidal<c+a>slip under compression along the normal direction of a hot-rolled Mg-4.5 wt.%Li plate,with a relative activity of approximately 18%.Although the limited activity of pyramidal<c+a>slip alone cannot accommodate a large plastic strain,it effectively reduces the number of{10.11}−{10.12}double twins,which are believed to be favorable sites for crack initiation.The evidently reduced activity of double twins leads to a lower cracking tendency,and therefore improves ductility.

Machine learning-assisted efficient design of Cu-based shape memory alloy with specific phase transition temperature

The martensitic transformation temperature is the basis for the application of shape memory alloys(SMAs),and the ability to quickly and accurately predict the transformation temperature of SMAs has very important practical significance.In this work,machine learning(ML)methods were utilized to accelerate the search for shape memory alloys with targeted properties(phase transition temperature).A group of component data was selected to design shape memory alloys using reverse design method from numerous unexplored data.Component modeling and feature modeling were used to predict the phase transition temperature of the shape memory alloys.The experimental results of the shape memory alloys were obtained to verify the effectiveness of the support vector regression(SVR)model.The results show that the machine learning model can obtain target materials more efficiently and pertinently,and realize the accurate and rapid design of shape memory alloys with specific target phase transition temperature.On this basis,the relationship between phase transition temperature and material descriptors is analyzed,and it is proved that the key factors affecting the phase transition temperature of shape memory alloys are based on the strength of the bond energy between atoms.This work provides new ideas for the controllable design and performance optimization of Cu-based shape memory alloys.

Microstructures,corrosion behavior and mechanical properties of as-cast Mg-6Zn-2X(Fe/Cu/Ni)alloys for plugging tool applications

Mg-6Zn-2X(Fe/Cu/Ni)alloys were prepared through semi-continuous casting,with the aim of identifying a degradable magnesium(Mg)alloy suitable for use in fracturing balls.A comparative analysis was conducted to assess the impacts of adding Cu and Ni,which result in finer grains and the formation of galvanic corrosion sites.Scanner electronic microscopy examination revealed that precipitated phases concentrated at grain boundaries,forming a semi-continuous network structure that facilitated corrosion penetration in Mg-6Zn-2Cu and Mg-6Zn-2Ni alloys.Pitting corrosion was observed in Mg-6Zn-2Fe,while galvanic corrosion was identified as the primary mechanism in Mg-6Zn-2Cu and Mg-6Zn-2Ni alloys.Among the tests,the Mg-6Zn-2Ni alloy exhibited the highest corrosion rate(approximately 932.9 mm/a)due to its significant potential difference.Mechanical testing showed that Mg-6Zn-2Ni alloy possessed suitable ultimate compressive strength,making it a potential candidate material for degradable fracturing balls,effectively addressing the challenges of balancing strength and degradation rate in fracturing applications.

Influence of layer thickness on formation quality,microstructure,mechanical properties,and corrosion resistance of WE43 magnesium alloy fabricated by laser powder bed fusion

Laser powder bed fusion(L-PBF)of Mg alloys has provided tremendous opportunities for customized production of aeronautical and medical parts.Layer thickness(LT)is of great significance to the L-PBF process but has not been studied for Mg alloys.In this study,WE43 Mg alloy bulk cubes,porous scaffolds,and thin walls with layer thicknesses of 10,20,30,and 40μm were fabricated.The required laser energy input increased with increasing layer thickness and was different for the bulk cubes and porous scaffolds.Porosity tended to occur at the connection joints in porous scaffolds for LT40 and could be eliminated by reducing the laser energy input.For thin wall parts,a large overhang angle or a small wall thickness resulted in porosity when a large layer thicknesses was used,and the porosity disappeared by reducing the layer thickness or laser energy input.A deeper keyhole penetration was found in all occasions with porosity,explaining the influence of layer thickness,geometrical structure,and laser energy input on the porosity.All the samples achieved a high fusion quality with a relative density of over 99.5%using the optimized laser energy input.The increased layer thickness resulted to more precipitation phases,finer grain sizes and decreased grain texture.With the similar high fusion quality,the tensile strength and elongation of bulk samples were significantly improved from 257 MPa and 1.41%with the 10μm layer to 287 MPa and 15.12%with the 40μm layer,in accordance with the microstructural change.The effect of layer thickness on the compressive properties of porous scaffolds was limited.However,the corrosion rate of bulk samples accelerated with increasing the layer thickness,mainly attributed to the increased number of precipitation phases.

Ni-P/金刚石超硬复合涂层制备及其性能研究

【目的】解决Ni-P复合涂层本身硬度较低的问题。【方法】选择添加金刚石微粉制备Ni-P/金刚石复合涂层。首先通过正交试验得到了制备Ni-P/金刚石复合涂层的最佳工艺参数,其次通过单因素试验研究了各工艺参数对复合涂层力学性能的影响,最后通过SEM,XRD,EDS对最佳工艺参数下的复合涂层进行表征。【结果】根据试验成功计算出最佳工艺参数。【结论】制备Ni-P/金刚石复合涂层的最佳工艺参数为电流密度4 A/dm2、金刚石浓度5 g/L、搅拌速度150 r/min、镀液温度60℃,研究了各工艺参数对复合涂层力学性能的影响。