Electroless Ni-P plating on Mg-Li alloy by two-step method

Pretreated Mg-Li alloy sheets were pre-plated in a NiCO3？2Ni（OH）2？4H2O solution to form a thin Ni-P alloy film and then plating in a NiSO4？6H2O solution was carried out to obtain a protective coating.The surface morphology,structure and corrosion resistance of the coating were studied.The results showed that a flat,bright and compact plating layer,which was integrated into the matrix metal,was obtained.The P content of the Ni-P coating reached 13.56%（mass fraction）.The hardness value of the Ni-P coating was about HV 549.The polarization curve showed that the corrosion potential of the Ni-P coating reached ？0.249 V（vs SCE）.A long passivation region was found on the polarization curve,and this phenomenon indicated that the coating has an excellent anti-corrosion property.

An in situ measure method to study deposition mechanism of electroless Ni-P plating on AZ31 magnesium alloy

An in situ method was designed to measure a continuous open circuit potential （OCP） curve of AZ31 magnesium alloy and to observe the morphology variation of Ni-P coating during the process of the electroless plating. The deposition mechanism of the electroless Ni-P plating on AZ31 Mg alloy was studied by OCP curve, scanning electron microscopy （SEM）, and energy dispersion spectroscopy （EDS）. The process of electroless Ni-P plating contains the coating formation stage and the coating growth stage. The formation stage includes three procedures, i.e., the nucleation and growth of Ni crystallites, the extension of the coating in two-dimensional （2D） direction and the coalescence of the coating along three-dimensional （3D） direction. SEM investigations demonstrate that the spherical nodules of the Ni-P coating are not only formed during the coating growth stage, but also generated in the initial deposition stage of electroless Ni-P plating. The variation of the coating rates at different deposition stages corresponds to the deposition mechanism of their respective deposition stage.

Effect of novel ternary ligand system on acidic electroless Ni-P plating on AZ91D magnesium alloy

The electroless Ni-P coatings on AZ91 D magnesium alloy substrate were prepared using the acidic hypophosphite-reduced electroless nickel bath containing the novel ternary ligand system. The results indicate that the deposition rate varies with the ternary ligand concentration in plating solution. The structural and morphological characteristics of the coatings were analyzed by XRD and SEM. The anticorrosion properties of the Ni-P coatings were evaluated in 3.5% NaCl solution by electrochemical impedance and potentiodynamic polarization methods. The amount of ternary ligands in electroless plating bath has an significant effect on the surface morphology and structure of Ni-P coatings. The decrease of crystallization temperature and increase of crystallization heat of all the deposits with an increase in ternary ligand concentration are found by DSC measurements. The coating obtained with 0.035 mol/L ternary ligand additive in plating bath can offer a better surface homogeneity and improve corrosion resistance.

Homogenization pretreatment and electroless Ni-P plating on AZ91D magnesium alloy

Electroless nickel plating on AZ91D substrate with a new and eco-friendly pretreatment process based on tuning an electrochemical homogeneous surface was investigated. The morphology, deposition process, chemical composition and microstructure of Ni-P coating were studied. It is indicated that β phases are selectively removed, producing a microstructural homogeneous surface and the subsequent uniform and compact Zn immersion layer. A defect-free and well adhesive Ni-P coating can be successfully obtained due to its uniform nucleation and growth based on such pretreatment. Potentiodynamic polarization and electrochemical impedance spectroscopy （EIS） tests reveal that Ni-P coating could significantly improve the corrosion resistance of AZ91D substrate.

Pretreatment-free Ni-P plating on magnesium alloy at low temperatures

Electrochemically promoted electroless plating(EPEP)was used for the application of pretreatment-free Ni-P coating on AM60B magnesium alloy at low temperatures and the obtained coating was characterized by SEM,AFM,EDS and XRD techniques.Compact,uniform,and medium-phosphorus Ni-P coating with mixed crystalline-amorphous microstructure was obtained by applying a cathodic current density of4mA/cm^2at50℃.Also,island-like nickel clusters were deposited on the alloy surface under the same plating condition but without applying the cathodic current.In addition,the durability of the magnesium alloy against corrosion was strongly improved after plating via EPEP technique which was revealed by electrochemical examinations in3.5%NaCl(mass fraction)corrosive electrolyte.The results of the electrochemical examinations were confirmed by microscopic observations.Thickness,microhardness,porosity and adhesive strength of the deposits were also qualified.

Corrosion and wear properties of electroless Ni-P plating layer on AZ91D magnesium alloy

A direct electroless Ni-P plating treatment was applied to AZ91D magnesium alloy for improving its corrosion resistance and wear resistance. Corrosion resistance of the Ni-P coatings was evaluated by potentiodynamic polarization and immersing experiments in 3.5% NaCl solution. The wear resistance of the coatings was investigated by the wear track and the mass change after ball-on-disk experiment. The results show that corrosion resistance and wear resistance of the AZ91D alloy are greatly improved after direct electroless Ni-P plating. No discoloration is noticed until 4 d of immersion in 3.5% NaCl solution. Potentiodynamic polarization experiments show that the free corrosion potential of magnesium alloy is shifted from -1 500 mV to -250 mV and passivation occurs at 1 350 mV after direct electroless plating. The friction coefficients and wear rates of Ni-P coating and Ni-P coating after tempering are 0.10-0.351, 9.038×10-3 mm3/m and 0.13-0.177, 3.056×10-4 mm3/m, respectively, at a load of 1.5 N with dry sliding. Although minor hurt on corrosion resistance was caused, significant improvement of wear resistance was obtained after tempering treatment of the coating.

Direct electroless Ni-P plating on AZ91D magnesium alloy

An electroless Ni-P plating treatment was applied on AZ91D magnesium alloy to improve its corrosion resistance. Optimum pretreatment conditions and optimum bath of electroless nickel plating for magnesium alloy were found through many experiments. In order to avoid bother of pre-plating medium layer, a set of procedure of direct electroless Ni-P under the acid condition was investigated. The properties of the coating with 10% phosphorus were investigated. The results show that a coating with high hardness, low porosity and good adhesive strength is obtained. X-ray diffraction patterns show that the structure of the coating is an amorphous phase. After annealing at 400℃, the amorphous phase of Ni-P is transformed to crystalline phases, and some intermetallics as Ni3P and Ni5P2 are deposited from Ni-P solid solution along with an enhancing hardness from Hv 450 to Hv 910.

Electroless plating and growth kinetics of Ni-P alloy film on SiC_p/Al composite with high SiC volume fraction

After Sn/Pd activating, the SiCp/Al composite with 65% SiC (volume fraction) was coated by electroless Ni?P alloy plating. Surface morphology of the composite and its effect on the Ni?P alloy depositing process and bonding action of Ni and P atoms in the Ni?P alloy were studied. The results show that inhomogeneous distribution of the Sn/Pd activating points results in preferential deposition of the Ni?P alloy particles on the Al alloy and rough SiC particle surfaces and in the etched caves. The Ni?P alloy film has an amorphous structure where chemical bonding between Ni and P atoms exists. After a continuous Ni?P alloy film formed, electroless Ni?P alloy plating is not affected by surface morphology and characteristics of the SiCp/Al composite any longer, but by the electroless plating process itself. The Ni?P alloy film follows linear growth kinetics with an activation energy of 68.44 kJ/mol.

TWIP钢表面Ni-P化学镀层组织结构及性能研究

目的在孪生诱发塑性钢(TWIP)表面制备Ni-P镀层,提高TWIP钢的耐腐蚀性能。方法通过化学镀工艺在TWIP钢表面制备了高磷Ni-P镀层,并进行不同温度的热处理,利用扫描电镜及能谱仪、X射线衍射仪及原子力显微镜等探究了热处理温度和时间对Ni-P镀层形貌和组织结构的影响。通过电化学方法研究了TWIP钢表面镀层的耐蚀性能。结果随着热处理温度的升高,镍磷原子发生迁移,胞状组织边界模糊,粗糙度降低,其中600℃热处理镀层表面最为致密平整。随着热处理温度的升高,镀层组织结构演变过程如下:非晶态(普通镀层)→非晶态部分晶化,Ni12P5、Ni5P2等亚稳态镍磷化合物析出(300℃)→非晶态完全晶化、稳态Ni3P相长大(400℃)→晶粒长大(500℃、600℃)。Ni-P镀层能够明显提升TWIP钢的耐腐蚀性能。随着热处理温度的升高,镀层的耐蚀性能先降低后升高。600℃热处理1h镀层的腐蚀电流密度为0.25μA/cm^(2),与普通Ni-P镀层相比降低了80.9%,与TWIP钢基体相比降低了99.6%。600℃热处理镀层光滑致密无缺陷的表面促进了保护性氧化膜的产生,使镀层的耐蚀性能提高。结论合适的热处理工艺提高了Ni-P镀层的致密性和保护能力,光滑致密无缺陷的镀层能够为TWIP钢提供良好的防护。

低浓度硫酸铜对化学镀Ni-P镀层微观结构及性能的影响

为改善镍磷(Ni-P)镀层的表面质量、提高Ni-P镀层的性能,在化学镀Ni-P镀液中加入少量的硫酸铜(CuSO_(4)·5H_(2)O)制备Ni-P镀层。利用扫描电镜、能谱仪、X射线衍射仪分析了镀层的表面形貌、成分和结构,研究了CuSO_(4)·5H_(2)O浓度对镀层的微观结构、表面粗糙度、光泽度、硬度、耐磨性和耐蚀性的影响。研究表明:当CuSO_(4)·5H_(2)O浓度为0.1 g/L时,镀层为致密的非晶态节瘤状组织,具有最佳的耐蚀性;当CuSO_(4)·5H_(2)O浓度为0.2 g/L时,镀层表面质量最好,硬度高、耐磨性优异,但镀层中出现少量微晶态Ni-Cu固溶体,耐蚀性下降;当CuSO_(4)·5H_(2)O浓度超过0.2 g/L后,镀层为混晶态菜花状组织,镀层表面的质量和耐蚀性随CuSO_(4)·5H_(2)O浓度的增加不断恶化。

无界域上具有记忆的非自治Plate方程随机吸引子的存在性

研究无界域上一类具有衰退记忆和加性噪声的非自治Plate方程解的长时间行为.利用一致估计验证了解的拉回渐近紧性,获得了其随机吸引子的存在性.

化学镀Ni-P/Sn2.5Ag0.7Cu0.1RE微连接焊点热时效过程组织与性能

为探究化学镀Ni-P无铅焊点在热时效作用下的组织与性能,采用化学镀方法在T2紫铜表面制备Ni-P层,使用Sn_(2.5)Ag_(0.7)Cu_(0.1)RE钎料通过回流焊方法制备化学镀Ni-P无铅焊点。结果表明:微焊点Ni-P/钎缝过渡区域金属间化合物(IMC)初始组织为呈块状的(Ni,Cu)_(3)Sn_(4),平均厚度为1.5μm。在180℃条件下时效100 h过程中,微焊点Ni-P/钎缝过渡区(Ni,Cu)_(3)Sn_(4)IMC形貌逐渐转变为层状并增厚至3.3μm,微焊点剪切断裂位置由钎缝处向Ni-Sn-P/IMC交界处转移,断裂方式由韧性断裂转变为脆性断裂,相应微焊点的推剪力由初始的16 N下降11.9%。

Study of Electroless Ni-P-CNTs Composite Plating

The electroless Ni-P-carbon nanotubes composite plating was studied on the copper substrate. Metallurgical microscope, scanning electronic microscope, X-ray diffractometer and micro hardness tester were used to study the structure, constitution and performance of the electroless Ni-P-carbon nanotubes composite deposit. Experiential results show that, with the increment of carbon nanotubes content in electroless plating solution, the grain size on the sample surface decreases whereas the density of grains and the hardness for composite deposit increases. Moreover, adding carbon nanotubes not only improves the degree of crystallization for the composite deposit but also helps their transformation from the amorphous state to the nanocrystal state.

High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

Ti/(Ti,Cr)N/CrN multilayer coated 316L stainless steel by arc ion plating as bipolar plates for proton exchange membrane fuel cells

Arc ion plating (AIP) is applied to form Ti/(Ti,Cr)N/CrN multilayer coating on the surface of 316L stainless steel (SS316L) as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The characterizations of the coating are analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Interfacial contact resistance (ICR) between the coated sample and carbon paper is 4.9 m Omega cm(2) under 150 N/cm(2), which is much lower than that of the SS316L substrate. Potentiodynamic and potentiostatic tests are performed in the simulated PEMFC working conditions to investigate the corrosion behaviors of the coated sample. Superior anticorrosion performance is observed for the coated sample, whose corrosion current density is 0.12 mu A/cm(2). Surface morphology results after corrosion tests indicate that the substrate is well protected by the multilayer coating. Performances of the single cell with the multilayer coated SS316L bipolar plate are improved significantly compared with that of the cell with the uncoated SS316L bipolar plate, presenting a great potential for PEMFC application. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

Electrochemical behavior of Cu-Zn-Al shape memory alloy after surface modification by electroless plated Ni-P

The electrochemical behavior of Cu-Zn-Al shape memory alloy (SMA) with andwithout electroless plated Ni-P was investigated by electrochemical methods, in artificial Tyrode'ssolution. The results showed that Cu-Zn-Al SMA engendered dezincification corrosion in Tyrode'ssolution. The anodic active current densities as well as electrochemical dissolution sensitivity ofthe electroless plated Ni-P Cu-Zn-Al SMA increased with NaCl concentration rising, pH of solutiondecreasing and environmental temperature uprising. X-ray diffraction analysis indicated that aftersurface modification by electroless plated Ni-P, an amorphous plated film formed on the surface ofCu-Zn-Al SMA. This film can effectively isolate matrix metal from corrosion media and significantlyimprove the electrochemical property of Cu-Zn-Al SMA in artificial Tyrode's solution.

Wear and Corrosion Resistance of Electroless Plating Ni-P Coating on P110 Steel

In order to improve the surface performance and increase the lifetime of P 110 oil casing tube steel during operation, electroless plating was conducted to form Ni-P coating onto its surface. The surface morphology/element distribution and phase constitution of the Ni-P coating were analyzed using scanning electron microscope （SEM） equipped with energy dispersive spectrometry （EDS） and X-ray diffraction （XRD）. Tribological and electrochemical measurement tests were applied to investigate the wear and corrosion resistance of P110 steel and the Ni-P coating. The results showed that a uniform and compact, high phosphorous Ni-P coating was formed. The obtained Ni-P coating indicated certain friction-reduction effect and lower mass loss during friction-wear tests. The Ni-P coating also exhibited higher corrosion resistance in comparison with bared P 110 steel. The obtained N i-P coating has significantly improved the surface performance of P110 steel.

Mechanical assisted electroless barrel-plating Ni-P coatings on magnesium alloy

A mechanically assisted electroless barrel-plating Ni-P was carried out in a rolling drum containing Mg alloy specimens and ceramic balls, which was submerged in a bath containing electroless plating solution deposited by this novel technique have a It is demonstrated that the Ni-P coatings crystallized Ni-P solid solution structure, showing fine-grains, higher hardness, and higher corrosion resistance compared with the conventional electroless plated amorphous Ni-P coatings. After heat treatment at 400 ℃ for 1 h, the structure of such Ni-P coatings were transformed to a structure with Ni-Ni3P double phases, and cracks in these coatings could not be observed, whereas cracks appeared seriously in the conventional electroless plated Ni-P coating after same heat treatment. Therefore, both hardness and corrosion resistance of these Ni-P coatings can be improved further by heat treatment. All of these beneficial effects can be attributed to the role of mechanical attrition during the mechanically assisted electroless barrel-plating process.

Evaluation of residual stress and corrosion behaviour of electroless plated Ni-P/Ni-Mo-P coatings

Single Ni-P and Ni-Mo-P coatings as well as duplex Ni-P/Ni-Mo-P coatings with the same compositions were prepared by electroless plating.The residual stresses of the coatings on the surface and cross sections were measured by nanoindentation and AFM analysis,and the corrosion behaviour of the coatings in10%HCl solution was evaluated by electrochemical methods,to establish the correlation between the residual stresses and corrosion behaviour of the coatings.The results showed that the single Ni-P and duplex Ni-P/Ni-Mo-P coatings presented residual compressive stresses of241and206MPa respectively,while the single Ni-Mo-P coating exhibited a residual tensile stress of257MPa.The residual compressive stress impeded the growth of the pre-existing porosity in the coatings,protecting the integrity of the coating.The duplex Ni-P/Ni-Mo-P coatings had better corrosion resistance than their respective single coating.In addition,the stress states affect the corrosive form of coatings.

Fabrication and thermal stability of Ni-P coated diamond powder using electroless plating

Ni-P coated diamond powder was fabricated successfully by using electroless plating.Effects of active solutions,plating time,reaction temperature,and the components of the plating bath on the Ni-P coating were investigated systematically.Moreover,a study on the thermal stability of Ni-P coated diamond under various atmospheres was performed.The results indicate that Pd atoms absorbed on the diamond surface as active sites can consequently enhance the deposition rate of Ni effectively.The optimized plating bath and reaction conditions improve both the plating speed and the coverage rate of Ni-P electroless plating on the diamond surface.Compared to the diamond substrate,the diamond coated with Ni-P films exhibits very high thermal stability and can be processed up to 900°C in air and 1300°C in protective atmosphere such as H2.