Na_(2)CO_(3)·10H_(2)O-Na_(2)HPO_(4)·12H_(2)O/SiO_(2)复合定形相变材料的制备及应用

以Na_(2)CO_(3)·10H_(2)O(SCD)、Na_(2)HPO_(4)·12H_(2)O(DHPD)为相变主体制备了共晶体系,通过绘制凝固点变化图与DSC测试共同确定在m(SCD)∶m(DHPD)=4∶6时形成共晶,FTIR和XRD结果显示,2种水合盐间没有发生化学反应,但其晶型结构发生改变。通过添加质量分数为2%的Na2SiO3·9H_(2)O作为成核剂降低体系的过冷度,且经历50次相变循环体系未出现相分离,相变焓值仅下降0.25%。进一步使用质量分数为25%的气相SiO_(2)作为支撑材料,采用浸渍法制备了相变前后形状稳定的共晶水合盐/SiO_(2)定形相变材料(SSPCM)。所得SSPCM的相变温度为24.08℃,相变焓值为146.6J/g,过冷度为0.55℃,热导率为0.4571W/(m·K)。同保温泡沫相比,其可将模拟房内部中心温度的升温时间延长了1.81倍,降温时间延长了0.39倍。

A Fiber Optic Sensor for 2,4-dichlorophenol Analysis based on Optical Composite Oxygen-sensitive Film

A novel fiber optic sensor based on optical composite oxygen-sensitive film was developed for determination of 2,4-dichlorophenol(DCP).The optical composite oxygen-sensitive film consists of tris(2,2’-bipyridyl)dichloro ruthenium(II)hexahydrate(Ru(bpy)3Cl2)as the fluorescence indicator and iron(III)tetrasulfophthalocyanine(Fe(III)PcTs)as bionic enzyme.A lock-in amplifier was used for detecting the lifetime of the composite oxygen-sensitive film by measuring the phase delay of the sensor head.The different variables affecting the sensor performance were evaluated and optimized.Under the optimal conditions(i e,pH 6.0,25℃,Fe(III)PcTs concentration of 5.0×10^-5 mol/L),the linear detection range,detection limit and response time of the fiber optic sensor are 3.0×10^-7-9.0×10^-5 mol/L,4.8×10^-8 mol/L(S/N=3),and 220 s,respectively.The sensor displays high selectivity,good repeatability and stability,which have good potentials in analyzing DCP concentration in practical water samples.

Ag_(3)PO_(4)/Cu_(2)O复合材料的制备及其性能研究

对磷酸银复合材料制备及光催化性能进行了研究。讨论了水热温度、反应溶液的酸碱度等对Cu_(2)O制备的影响。同时,比较了不同摩尔百分比Ag_(3)PO_(4)含量的Ag_(3)PO_(4)/Cu_(2)O复合材料的光催化降解活性。结果显示,球状Cu_(2)O颗粒制备条件为:温度100℃,pH值为10。采用直接沉淀法Ag_(3)PO_(4)纳米颗粒能够均匀附着Cu_(2)O表面,达到最佳复合效果。Ag_(3)PO_(4)/Cu_(2)O复合材料光催化活性高于纯Cu_(2)O,随着Ag_(3)PO_(4)的摩尔百分量的增加,复合光催化剂的催化性能先是增强后逐渐减弱。60%Ag_(3)PO_(4)/Cu_(2)O时,催化活性最强,90 min内罗丹明B几乎完全降解。

The effects of radiation damage on power VDMOS devices with composite SiO_2-Si_3N_4 films

Total dose effects and single event effects on radiation-hardened power vertical double-diffusion metal oxide semiconductor（VDMOS） devices with composite SiO2-Si3N4 film gates are investigated.The relationships among the important electrical parameters of the samples with different thickness SiO2-Si3N4 films,such as threshold voltage,breakdown voltage,and on-state resistance in accumulated dose,are discussed.The total dose experiment results show that the breakdown voltage and the on-state resistance barely change with the accumulated dose.However,the relationships between the threshold voltages of the samples and the accumulated dose are more complex,and not only positively drift,but also negatively drift.At the end of the total dose experiment,we select the group of samples which have the smaller threshold voltage shift to carry out the single event effect studies.We find that the samples with appropriate thickness ratio SiO2-Si3N4 films have a good radiation-hardening ability.This method may be useful in solving both the SEGR and the total dose problems with the composite SiO2-Si3N4 films.

Corrosion resistance evaluation of highly dispersed MgO–MgAl2O4–ZrO2 composite and analysis of its corrosion mechanism: A chromium-free refractory for RH refining kilns

The corrosion resistance behavior of a highly dispersed MgO-MgAl2O4-ZrO2 composite refractory material is examined by testing with high-basicity and low-basicity RH(Ruhrstahl-Hereaeus)slags.The composite material exhibits greater resistance to the RH slags than the traditional MgO-Cr2O3 composite,MgO-ZrO2 composite,and MgO-MgAl2O4-ZrO2 composite.On the basis of the microstructural analysis and mechanisms calculations,the corrosion resistance behavior of the MgO-MgAl2O4-ZrO2 composite is attributable to its highly dispersed structure,which helps protect the high activity of ZrO2.When in contact with the slag,ZrO2 reacts with CaO to form the stable phase CaZrO3,which protects MgAl2O4 against corrosion,thereby enhancing the corrosion resistance of the composite.

Effect of Al2O3np on the Properties and Microstructure of B4Cp/Al Composites

Aluminum-matrix boron carbide (B4Cp/Al) is a kind of neutron absorbing material widely used in nuclear spent fuel storage. In order to improve the tensile property of B4Cp/Al composites, a new type of nano-Al2O3 particle (Al2O3np) reinforced B4Cp/Al + Al2O3np composites were prepared by powder metallurgy method. The Monte Carlo particle transport program (MCNP) was used to determine the influence of Al2O3np on the thermal neutron absorptivity of composites. The universal material testing machine and scanning electron microscope (SEM) were used to study the mechanical properties, microstructure and fracture morphology of B4Cp/Al composites. The results indicated that the neutron absorption properties of B4Cp/Al composites were not affected by the addition of nano-Al2O3 particles in the range of 1 wt%-15 wt%. The addition of Al2O3np can obviously reduce the grain size of B4Cp/Al matrix metals thus improve the tensile strength of the composites. The addition threshold of Al2O3np is about 2.5 wt%. Both B4Cp and Al2O3np change the fracture characteristics of the composites from toughness to brittleness, and the latter is more important.

Fabrication of Fine-Grained Si_3N_4-Si_2N_2O Composites by Sintering Amorphous Nano-sized Silicon Nitride Powders

Si3N4-Si2N2O composites were fabricated with amorphous nano-sized silicon nitride powders by the liquid phase sintering （ LPS ）. The Si2 N2O phase was generated by an in-situ reaction 2 Si3 N4 （ s ） ＋ 1.5 02 （ g ） = 3 Si2 N2O （ s ） ＋ N2 （ g ） . The content of Si2 N2 O phase up to 60% in the volume was obtained at a sintering temperature of 1 650℃ and reduced when the sintering temperature increased or decreased, indicating the reaction is reversible. The mass loss, relative density and average grain size increased with increasing the sintering temperature. The average grain size was less than 500 nm when the sintering temperature was below 1 700 ℃. The sintering procedure contains a complex crystallization and a phase transition ： amorphous silicon nitride→equiaxial α- Si3 N4→ equiaxial β- Si3 N4→ rod- like Si2 N2O→ needle- like β- Si3N4 . Small round-shaped β→ Si3 N4 particles were entrapped in the Si2 N2O grains and a high density of staking faults was situated in the middle of Si2 N2O grains at a sintering temperature of 1 650 ℃. The toughness inereased from 3.5 MPa·m^1/2 at 1 600 ℃ to 7.2 MPa· m^1/2 at 1 800 ℃ . The hardness was as high as 21.5 GPa （Vickers） at 1 600 ℃ .

Preparation and characterization of SnO_2-Li_4Ti_5O_(12) composite by sol-gel technique

SnO2-Li4Ti5O12 was prepared by sol-gel method using tin tetrachloride,lithium acetate,tetrabutylorthotitanate and aqueous ammonia as starting materials.The composite was characterized by thermogravimertric(TG)analysis and differential thermal analysis(DTA),X-ray diffractometry(XRD)and transmission electron microscopy(TEM)combined with electrochemical tests.The results show that SnO2-Li4Ti5O12 composite derived by sol-gel technique is a nanocomposite with core-shell structure, and the amorphous Li4Ti5O12 layer with 20?40 nm in thickness is coated on the surface of SnO2 particles.Electrochemical tests show that SnO2-Li4Ti5O12 composite delivers a reversible capacity of 688.7 mA·h/g at 0.1C and 93.4%of that is retained after 60 cycles at 0.2C.The amorphous Li4Ti5O12 in composite can accommodate the volume change of SnO2 electrode and prevent the small and active Sn particles from aggregating into larger and inactive Sn clusters during the cycling effectively,and enhance the cycling stability of SnO2 electrode significantly.

Kinetics and Thermodynamics of Adsorption Methylene Blue onto Tea Waste/CuFe₂O₄Composite

Tea waste/CuFe2O4 (TW/C) composite was prepared by co-precipitation method. The TW and TW/C samples are characterized by FTIR, XRD, SEM and N2 physical adsorption. The results showed that specific surface area of 350 and 570 m2·g?1 for TW and TW/C, respectively. The average pore size of TW/C is ca. 100 nm. Adsorption of methylen blue onto TW/C composite has been studied. Measurements are performed at various contact time, pH and adsorbent dosage. The adsorption kinetics of methylen blue (MB) could be described by the pseudo-second order kinetic model. The adsorption isotherms are described by means of Langmuir and Freundlich isotherms. It was found that the Freundlich model fit better than the Langmuir model. The thermodynamic constants of the adsorption were calculated to predict the nature of adsorption. The values of thermodynamic parameters indicate that a spontaneous and endothermic process was occurred.

NiO-ZnFe_2O_4复合薄膜光波导传感元件的气敏性研究

用溶胶凝胶法制成了Ni O掺杂的Zn Fe2O4溶胶并用浸渍提拉法将其固定在锡参杂玻璃光波导表面,研制了Ni O-Zn Fe2O4复合薄膜/锡掺杂玻璃光波导气敏元件,并对挥发性有机气体进行了检测。实验结果表明,该传感元件对二甲苯气体具有较好的响应,并能够检测到体积比浓度为1.0×10-7mg/m3的二甲苯气体。该元件具有灵敏度高,响应-恢复快、重复性好、在室温下便于操作等特点。

Synthesis and Characterization of Superparamagnetic Fe₃O₄@SiO₂Core-Shell Composite Nanoparticles

The Fe3O4@SiO2 composite nanoparticles were obtained from as-synthesized magnetite (Fe3O4) nanoparticles through the modified St?ber method. Then, the Fe3O4 nanoparticles and Fe3O4@SiO2 composite nanoparticles were characterized by means of X-ray diffraction (XRD), Raman spectra, scanning electron microscope (SEM) and vibrating sample magnetometer (VSM). Recently, the studies focus on how to improve the dispersion of composite particle and achieve good magnetic performance. Hence effects of the volume ratio of tetraethyl orthosilicate (TEOS) and magnetite colloid on the structural, morphological and magnetic properties of the composite nanoparticles were systematically investi-gated. The results revealed that the Fe3O4@SiO2 had better thermal stability and dispersion than the magnetite nanoparticles. Furthermore, the particle size and magnetic property of the Fe3O4@SiO2 composite nanoparticles can be adjusted by changing the volume ratio of TEOS and magnetite colloid.

Fabrication and Magnetic Properties of Composite Ni_(0.5)Zn_(0.5)Fe_2O_4/Pb(Zr_(0.52)Ti_(0.48))O_3 Nanofibers by Electrospinning

One-dimensional and quasi-one-dimensional nanostructure materials are promising building blocks for electromagnetic devices and nanosystems.In this work,the composite Ni0.5Zn0.5Fe2O4（NZFO）/ Pb（Zr0.52Ti0.48）O3（PZT） nanofibers with average diameters about 65 nm are prepared by electrospinning from poly（vinyl pyrrolidone） （PVP） and metal salts.The precursor composite NZFO/PZT/PVP nanofibers and the subsequent calcined NZFO/PZT nanofibers are investigated by Fourier transform infrared spectroscopy （FT- IR） ,X-ray diffraction （XRD）,scanning electron microscopy （SEM）.The magnetic properties for nanofibers are measured by vibrating sample magnetometer（VSM）.The NZFO/PZT nanofibers obtained at calcination temperature of 900 °C for 2 h consist of the ferromagnetic spinel NZFO and ferroelectric perovskite PZT phases,which are constructed from about 37 nm NZFO and 17 nm PZT grains.The saturation magnetization of these NZFO/PZT nanofibers increases with increasing calcination temperature and contents of NZFO in the composite.

Electric and Magnetic Properties of the (1 -x)Bao.6Sr0.4TiO3-xCoFe2O4 Multiferroic Composite Ceramics

The(1-x)Bao.6Sro.4 TiO3-xCoFe2O4 multiferroic composite ceramics (x=0.15-0.45) were fabricated by using the solid-state reaction method.X-ray diffraction shows that the composites are composed of the perovskite Ba0.6Sr0.4TiO3 phase and cubic spinel CoFe2O4 phase,without the other secondary phase.Scanning electron microscopy shows that the morphology of the composites is dense and comparatively homogenous.The variations of the dielectric constant and loss with frequency and temperature indicate that the composites behave as relaxor ferroelectrics.The composites display ferromagnetic and ferroelectric properties simultaneously.The saturated polarization of the composites decreases with increasing ferrite content,while the remnant polarization increases with the increasing ferrite content.The remnant polarization of the composite with x =0.45 is even larger than that of the pure Ba0.6Sr0.4TiO3 ceramic.The enhanced ferroelectricity of the composites may be attributed to the space charge effect in the composites.

Oxidation Behavior of Fe26Cr1Mo Stainless Steel in the Presence of Ni-La_2O_3 Electrodeposited Composite Film

The oxidation behaviors of Fe26Cr1Mo with and without the Ni La 2O 3 electrodeposited composite film have been investigated by thermogravimetric analysis (TGA) and a scanning electron microscope equipped with an energy dispersive analytical X ray system(SEM/EDAX). The experimental results show that the oxide scale growing on Fe26Cr1Mo exposed at 900 ℃ spalled severely during cooling, while after the stainless steel was coated with the Ni La 2O 3 electrodeposited composite film, its high temperature cyclic oxidation resistance was significantly improved. The reason is that a La 2O 3 modified NiO scale, which has a superior adhesion to the substrate, was formed on the Fe26Cr1Mo stainless steel coated with Ni La 2O 3 composite film.

Synthesis and electrochemical properties of LiMn_2O_4/Li_4Ti_5O_(12) composite

LiMn2O4/Li4Ti5O12 composite was synthesized by in-situ composite technique using LiMn2O4,lithium acetate,tetrabutyl titanate as starting materials and characterized by various electrochemical methods in combination with X-ray diffractometry(XRD), infrared(IR)spectroscopy and scanning electron microscopy(SEM).The results show that Li4Ti5O12 is coated on the surface of crystalline LiMn2O4 to form LiMn2O4/Li4Ti5O12 composite.The structure of LiMn2O4 does not change due to the introduction of Li4Ti5O12.By being coated with Li4Ti5O12,the rate capability and high temperature cyclability of LiMn2O4 is improved greatly.At room temperature,the discharge capacity of LiMn2O4/Li4Ti5O12 composite is more than 108.4 mA·h/g and the capacity loss per cycle is only 0.053%after 20 cycles at 2.0C.While at 55℃,the discharge capacity of LiMn2O4/Li4Ti5O12 composite is more than 109.9 mA·h/g and the capacity loss per cycle is only 0.036%after 60 cycles at 1.0C.

Low-Frequency Dependence of Conductivity and Dielectric Properties of Polyaniline/ZnFe_(2)O_(4) Nanocomposites

Conducting polyaniline/ZnFe_(2)O_(4) nanocomposites are synthesized by using a simple and inexpensive one-step in-situ polymerization method in the presence of ZnFe2O4 nanoparticles.The structural,morphological and electrical properties of the samples are characterized by x-ray diffraction,Fourier transform infrared spectra and scanning electron microscopy.These results reveal the formation of polyaniline/ZnFe2O4 nanocomposites.The morphology of these samples is studied by scanning electron microscopy.Further,the ac conductivity(σac)of these composites is investigated in the frequency range of 1 kHz–10 MHz.The presence of polarons and bipolarons are responsible for the frequency dependence of ac conductivity in these nanocomposites.The ac conductivity is found to be constant up to 1MHz and thereafter it increases steeply.The ac conductivity of 0.695 S・cm^(−1) at room temperature is observed as the maxima for the polyaniline with 40wt%of the ZnFe2O4 nanocomposite.

Thermodynamic Analysis of Combusion Synthesis and Reaction Hot Pressing of Al_2O_3/B_4C Composite

The equilibrium phases and adiabatic temperature for combustion synthesis and reaction hot pressing of Al 2O 3/B 4C employing ① Al, B 2O 3 and C ② C, B, Al 2O 3 as starting reactants were analyzed by the CALPHAD technique. It is shown that the equilibrium phases at the adiabatic temperature in the combusion system (1) are not the intended composite Al 2O 3/B 4C but other phases. Good agreement with the experimental data was achieved for the calculated adiabatic temperature. The results were discussed with respect to the elimination of the by product in the combustion synthesis. It also revealed that the reactant mixture (2) is a weak exothermic or endothermic reaction system, which can be employed in the reaction hot pressing.

BaZr_(0.9)Y_(0.1)O_(2.95)/Na_2SO_4 Composite with Enhanced Protonic Conductivity

Heterogeneous composite BaZr0.9Y0.1O2.95/Na2SO4 was designed and fabricated with Y-doped BaZrO3 as matrix and Na2SO4 as dispersant by conventional powder processing to improve the total conductivity of barium zirconate. The electrical conduction of the composite was studied by electrical and electrochemical methods. Microstructure of the heterogeneous composite was examined by SEM. The experimewtal results show that the protonic conductivity of Y-doped BaZrO3 is greatly improved upon incorporating Na2SO4 in the material. Microstructure observation indicates that a multiphase structure with Na2SO4 disperses at the grain boundaries of BaZr0.1Y0.9O2.95. Electromotive force （EMF） measurements under fuel cell conditions reveal that the total ionic transport number of the composite is more than 0.9 at 750 ℃.

Mass Production of Bi3NbO7/Bi2Zn(2/3)Nb(4/3)O7 Composites and Their Visible-light Photocatalytic Activity

Series Bi3NbO7/Bi2Zn（2/3）Nb（4/3）O7 （BN/BZN） composites were synthesized through a facile solid state reaction method. The products were characterized by X-ray diffraction（XRD）, field emission scanning electron microscopy（FE-SEM） and UV-vis diffuse reflectance spectroscopy（DRS）. When BN： BZN=0.1 mole ratio, the BN/BZN composite showed the best visible-light-driven photocatalytic performance, which decomposed nearly 100% of Rh B（10 ppm, p H=3-4） within 40 min. The results demonstrated that in-situ solid state synthesis of BN/BZN composites could be an efficient strategy to develop new photocatalyst for environmental remediation.

LiMn_2O_4 thin films derived by rapid thermal annealing and their performance as cathode materials for Li ion battery

The LiMn2O4 thin film as a cathode material was prepared through solution deposition followed by rapid thermal annealing （RTA）. The phase identification and the study of surface morphology were carried out by X-my diffraction and scanning electron microscopy. Electrochemical properties were examined by cyclic voltammetry, galvanostatic charge-discharge experiments, and electrochemical impedance spectroscopy. The results show that the film prepared by this method is homogeneous, dense, and crack-free. The thin film has a capacity of 38 μtAh/（cm^2·μm） with the capacity loss of 0.037% per cycle after being cycled for 100 times. The average diffusion coefficient for lithium ions in the RTA-derived LiMn2O4 thin film is 1×10 ^-10 cm^2·s^-1.