Preparation and mechanical properties of two nickel base alloy coatings achieved by electrospark deposition

Ni398 and Ni818 base alloy coatings were deposited on 1045 steel by electrospark deposition technique （ESD）. Forming properties, thickness, microhardness and wear resistance of the coatings were investigated. The chemical composition and cross- section morphology were analyzed through energy dispersive spectrum （EDS） and metalloscope. The results show that the technological parameter window of Ni398 is larger than that of Ni818 electrode. However, other properties of the Ni818 coating, such as thickness and microhardness, were better than those of the Ni398 coating. Especially the wornout volume of Ni818 coating is only 1/6 of that for 1045 steel and 1/3 for Ni398 coating. Chemical composition analysis indicated that the addition of Mo promoted grain refinement of nickel alloy. Metallographic analysis shows that the molten droplets of Ni398 coatings have an average structure thickness of 20-40 #m while the microstructure of Ni818 coatings is flat with width of 5-20 #m.

NOTCH WEAR OF MACHINING NICKEL BASED ALLOYS WITH CERAMIC TOOLS

The performances of mixed ceramic and sialon ceramic tools in machining nickel based alloy are tested.The negative cutting edge inclination and small tool lead angle are recommended for reducing ceramic tool failure. So called“notching at depth of cut”is not actually at the depth of cutting line, but out of cutting area。 The real reason of notching is caused by shocking of “sawtooth”on sawtooth- shaped burr and fin- shaped edges of chip

Laser repairing surface crack of Ni-based superalloy components

Surface crack of components of the cast nickel base superalloy was repaired with twin laser beams under proper technological conditions. One laser beam was used to melt the substrate material of crack, and the other to fill in powder material to the crack region. The experimental results show that the surface crack with the width of 0.1 ～ 0.3?mm could be repaired under the laser power of 3?kW and the scanning speed of 6 ～ 8?mm/s. The repaired deepness of crack region is below 6.5?mm. The microstructure of repaired region is the cellular crystal, columnar crystal dendrite crystal from the transition region to the top filled layer. The phases in repaired region mainly consisted of supersaturated α Co with plenty of Ni, some Cr and Al, Cr 23 C 6, Co 2B, Co Ni Mo, Ni 4B 3, TiSi and VSi. The hardness of filled layer in repaired region ranged from HV 0.2 450 to HV 0.2 500, and the hardness decreases gradually from the filled layer to joined zone.

Surface Metallurgy of Nickle Base Superalloy

The Double Glow Plasma Surface Alloying Technique, the Xu-Tee Process, is a new method to produce high quality alloying layer on the surface of less expensive materials. By using thes technique, the surface alloying layer similar to superalloy Inconel 625 has been obtained on the surface of three kinds of melallic materials (low carbon steel, industrial pure iron, stainless steel Cr18Ni9). The results of the composition and microstructure analyzed by Scanning Electron Microscopy (SEM) and X-Ray Uffrachon (XRD) show that the alloying layer consistS of y matrix and several precipitates (Laves intermetallic phase and carbide etc.). The electrochemical corrosion results show that the surface alloying layer formed on the surface of stainless steel and industrial pure iron have better corrosion resistance than that of nickel base alloy inconel 625 and stainless steel Cr18Ni9 in 3.5%NaCl solution. The exper iments indicate that it is an effective way to obtain the gradient surface alloying layer on the surfaces of steels by using Double Glow Plasma Surface Alloying Technique.

OBSERVATION ON SPUTTERING SURFACE OF ALLOYS IN GLOW DISCHARGE

Glow discharge cathodic sputtering of alloys containing second phase precipitates or injected oxide particles has been observed with energy dispersive X-ray spectrometer and scanning electron microprobe.It was shown that the formation of cones during the sputtering in these alloys is due to masking of the matrix by glow sputtering second phase precipitates or oxide particles.At steady state,the density of cottes were found to be a function of the densities pre- cipitates or oxide particles in bulk alloy.In addition to the changes of local sputtering rate,the electrostatic effect may play a role on the formation fo cones.

Material Characterization of Ni Base Alloy for Very High Temperature Reactor

The generation of highly efficient electricity and the production of massive hydrogen are possible using a very high temperature reactor （VHTR） among generation IV nuclear power plants. The structural material for an intermediate heat exchanger （IHX） among numerous components should be endurable at high temperature of up to 950 °C during long-term operation. Impurities inevitably introduced in helium as a coolant facilitate the material degradation by corrosion at high temperature. In the present work, the surface reactions available under controlled impure helium at 950 °C were investigated based on the thermodynamics and the corrosion tests were performed in a temperature range of 850-950 °C during 10-250 h for commercial Alloy 617 as a candidate material for an IHX. Moreover, the mechanical property and microstructure for nickel-based alloys fabricated in laboratory were evaluated as a function of the processing parameters such as hot rolling and heat treatment conditions. From the reaction rate constant obtained from an impure helium control system for a material evaluation, it was predicted that the outer oxide layer thickness, internal oxide depth, and carbide- depleted zone depth reach about 116, 600 and 1000 μm, respectively when Alloy 617 is exposed to an impure helium environment at 950 ~C for 20 years. For Ni-Cr-Co-Mo alloy, subsequent annealing and a combination of cold working and subsequent annealing following solution annealing caused increases in the grain boundary carbide coverage and size. The angular distribution of the grain boundary as well as the carbide distribution was also changed leading to a consequent improvement of the mechanical property at 950 °C in air.

First-principles study of the effects of selected interstitial atoms on the generalized stacking fault energies, strength, and ductility of Ni

We analyze the influences of interstitial atoms on the generalized stacking fault energy （GSFE）, strength, and ductility of Ni by first-principles calculations. Surface energies and GSFE curves are calculated for the （112） （111） and / 101） （ 1 1 1） systems. Because of the anisotropy of the single crystal, the addition of interstitials tends to promote the strength of Ni by slipping along the （10T） direction while facilitating plastic deformation by slipping along the （115） direction. There is a different impact on the mechanical behavior of Ni when the interstitials are located in the slip plane. The evaluation of the Rice criterion reveals that the addition of the interstitials H and O increases the brittleness in Ni and promotes the probability of cleavage fracture, while the addition of S and N tends to increase the ductility. Besides, P, H, and S have a negligible effect on the deformation tendency in Ni, while the tendency of partial dislocation is more prominent with the addition of N and O. The addition of interstitial atoms tends to increase the high-energy barrier γmax, thereby the second partial resulting from the dislocation tends to reside and move on to the next layer.