NICKEL-BASE ALLOY SHEET ALLOYS USED IN AEROSPACE APPLICATIONS

Many gas turbine components are made from nickel alloy sheet. Most are used for directing or containing gases at high temperatures and pressures where metal temperatures can be as high as 1090℃ (2000°F). These applications included combustor systems, casings and liners, transition and exhaust ducting, afterburners, and thrust reversere. Light weight components and sub-assemblies call for alloy sheet with high levels of stength and oxidation resistance. Complex component design calls for excellent ductility and ease of fabrication.The wide range of nickel alloy sheet alloys presently used in aircraft and land-based gas turbines is briefly described and typical properties presented. New sheet alloy developments, involving INCONEL￣* alloys 625LCF, 718SPF and MA754, are presented including the process routes involved and material properties.

XPS analysis of passive film formed on the G3 nickel-base alloy tubing under corrosive conditions

In the present study, the passive film formed on the G3 nickel-base alloy tubing under corrosive conditions including H2S ,CO2 ,and Cl-at 130 ℃ and 205 ℃ is studied with X-ray photoelectron spectroscopy（XPS）. The results reveal that the passive film formed at 205℃ consists of Cr, Ni, Fe, S and O elements and is over 470 nm in thickness. The passive film can be divided into three layers, the outer-layer is composed of NiS2 and Cr2 S3 , the intermediate-layer of Cr（OH） 3, Ni （OH） 2, NiS2, Cr2 $3 and a small quantity of NiO and Cr2 O3, and the inner-layer of NiO, Cr2 O3, and alloy elements. Due to the invasion of S2 - into the passive film and the decrease of the content of chromium oxide in the film, the corrosion resistance of the G3 alloy in the sour environment at 205 ℃ is weakened.

Structural Characterization of Nickel-Base Alloy C-276 Irradiated with Ar Ions

The irradiation damage in nickel-base alloy C-276 irradiated with 115 keV Ar ions from low to very high doses was investigated. Structural characterization was performed using transmission electron microscopy （TEM）, grazing incident X-ray diffraction （GIXRD） and atomic force microscopy （AFM）. High density of interstitial type dislocation loops could be observed at a dose level of around 2.75 displacements per atom （dpa）. With the irradiation dose increased to 27.5 dpa, the average size of loops increased from 5 nm to 16 nm, while the density of the loops decreased from 1.4 × 1011/cm2 to 4.6 × 1010/cm2. When the irradiation dose reached 82.5 dpa, original grains were transformed into subgrains whose sizes observed from TEM were about 20-60 nm. The fragmentation of grains was confirmed by GIXRD. The mean subgrain size was 40 nm, which was obtained from the full width at half maximum （FWHM） of the X-ray diffraction lines using the Scherrer formula and Williamson formula. AFM micrographs showed that nanometer-sized hillocks formed at the dose of 82.5 dpa, which provided further evidence of grain fragmentation at a high irradiation dose.

Thermal desorption characteristic of helium ion irradiated nickel-base alloy

The nickel-base alloy is one of the leading candidate materials for generation IV nuclear reactor pressure vessel.To evaluate its stability of helium damage and retention,helium ions with different energy of 80 keV and 180 keV were introduced by ion implantation to a certain dose(peak displacement damage 1-10 dpa).Then thermal desorption spectroscopy(TDS)of helium atoms was performed to discuss the helium desorption characteristic and trapping sites.The desorption peaks shift to a lower temperature with increasing dpa for both 80 keV and 180 keV irradiation,reflecting the reduced diffusion activation energy and faster diffusion within the alloy.The main release peak temperature of 180 keV helium injection is relatively higher than that of 80 keV at the same influence,which is because the irradiation damage of 180 keV,helium formation and entrapment occur deeper.The broadening of the spectra corresponds to different helium trapping sites(He-vacancies,grain boundary)and desorption mechanisms(different Hen Vm size).The helium retention amount of 80 keV is lower than that of 180 keV,and a saturation limit associated with the irradiation of 80 keV has been reached.The relatively low helium retention proves the better resistance to helium bubbles formation and helium brittleness.

THE SEGREGATION OF SULFUR AND PHOSPHORUS IN NICKEL-BASE ALLOY 718

The segregation behavior of sulfur and phosphorus has been studied by means of scanning Auger microprobe (SAM) on microstructural interfaces,such as grain boundaries and carbide/matrix interfaces,The experimental results clearly reveal that sulfur strongly segregates on carbide/matrix interfaces,while phosphorus predominantly distributes on grain boundaries. Molybdenum tends to segregat on grain boundaries.

Microstructure Evolution of a Nickel-Base Alloy Resistant to High Temperature during Aging

In the present study, the microstructural evolution during aging at 1023, 1073, 1123 and 1173 K of a 35Cr-45Ni heat resistant alloy, produced in the form of centrifugally cast tubes, was characterized by means of light optical microscopy, scanning electron microscopy (SEM) with secondary and backscattered electron imaging, energy-dispersive X-ray spectroscopy (EDS) and Vickers hardness tests. The evolution of the Vickers hardness at 1023 K for aged samples shows that the microstructure is stable during the analyzed aging period. At 1073 K, the rate of increase in hardness is lower than 1023 K and this behavior would be associated with morphological changes observed in primary interdendritic carbides and secondary carbides in the matrix. At 1123 K and 1173 K, an atypical behavior in Vickers hardness curve is presented;where it can be seen that at certain aging times, the hardness decreases significantly. A microstructural analysis of these samples indicates that they have a region free of precipitates (near interdendritic edges) where the hardness is lower. Probably, these regions are areas poor in chromium.

Effect of the capsule on deformation and densification behavior of nickel-based superalloy compact during hot isostatic pressing

The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.

Recent advances in nickel-based catalysts in eCO_(2)RR for carbon neutrality

The excessive use of nonrenewable energy has brought about serious greenhouse effect.Converting CO_(2) into high-value-added chemicals is undoubtedly the best choice to solve energy problems.Due to the excellent cost-effectiveness and dramatic catalytic performance,nickel-based catalysts have been considered as the most promising candidates for the electrocatalytic CO_(2) reduction reaction(eCO_(2)RR).In this work,the electrocatalytic reduction mechanism of CO_(2) over Ni-based materials is reviewed.The strategies to improve the eCO_(2)RR performance are emphasized.Moreover,the research on Ni-based materials for syngas generation is briefly summarized.Finally,the prospects of nickel-based materials in the eCO_(2)RR are provided with the hope of improving transition-metal-based electrocatalysts for eCO_(2)RR in the future.

Effect of Interface Form on Creep Failure and Life of Dissimilar Metal Welds Involving Nickel-Based Weld Metal and Ferritic Base Metal

For dissimilar metal welds(DMWs)involving nickel-based weld metal(WM)and ferritic heat resistant steel base metal(BM)in power plants,there must be an interface between WM and BM,and this interface suffers mechanical and microstructure mismatches and is often the rupture location of premature failure.In this study,a new form of WM/BM interface form,namely double Y-type interface was designed for the DMWs.Creep behaviors and life of DMWs containing double Y-type interface and conventional I-type interface were compared by finite element analysis and creep tests,and creep failure mechanisms were investigated by stress-strain analysis and microstructure characterization.By applying double Y-type interface instead of conventional I-type interface,failure location of DMW could be shifted from the WM/ferritic heat-affected zone(HAZ)interface into the ferritic HAZ or even the ferritic BM,and the failure mode change improved the creep life of DMW.The interface premature failure of I-type interface DMW was related to the coupling effect of microstructure degradation,stress and strain concentrations,and oxide notch on the WM/HAZ interface.The creep failure of double Y-type interface DMW was the result of Type IV fracture due to the creep voids and micro-cracks on fine-grain boundaries in HAZ,which was a result of the matrix softening of HAZ and lack of precipitate pinning at fine-grain boundaries.The double Y-type interface form separated the stress and strain concentrations in DMW from the WM/HAZ interface,preventing the trigger effect of oxide notch on interface failure and inhibiting the interfacial microstructure cracking.It is a novel scheme to prolong creep life and enhance reliability of DMW,by means of optimizing the interface form,decoupling the damage factors from WM/HAZ interface,and then changing the failure mechanism and shifting the failure location.

Nickel-base superalloys for USC power plants

The advanced ultra-supercritical power plants of the future will utilize steam pressures and temperatures that are too high for traditional ferritic steels,thus requiring austenitic materials.Older nickel-base superalloys such as 263 and 617 were initially evaluated under the European THERMIE project beginning in the 1990s.An entirely new age-hardened alloy 740 which possesses exceptional fireside corrosion resistance and creep strength was also developed for boiler tubing capable of serving at 700C.Subsequently,interest in the USA considered other product forms such as steam header piping and steam turbine forgings for service as high as 760C.A more stable and weldable alloy version now called 740H was developed to meet these more demanding conditions.This paper summarizes the current status of work on alloys 740 and 740H.

Impulse Capacitor Discharge Welding of Hollow Structure Made of Nickel-Base Alloy

Future steam turbines will use hollow structures so that the turbine inlet temperature can be increased to improve the thermal efficiency. These hollow structures are made of the nickel-base alloy Nicrofer 6025 HT and consist of a wire mesh between two cover sheets. The cover sheets can be joined to the wire mesh by capacitor discharge welding due to its extremely short welding duration. The goal of this research is to investigate suitable welding parameters so that the weld spots form in an optimum way to increase the tensile shear strength and reduce spattering. Tensile shear tests, three-point bending tests, and micrographs were used to judge the joint quality of structures made with various welding parameters. The results show that the best welds are obtained with a transmission ratio of 1：200, welding energy of 70% to 95%, and electrode force of 7 to 9 MPa.

Research on CMT welding of nickel-based alloy with stainless steel

Cold Metal Transfer （CMT） welding technique is a new welding technique introduced by Fronins company. CMT welding of nickel-based alloy with stainless steel was carried out using CuSi3 filler wire in this paper. Effects of welding parameters, including welding current, welding speed, etc, on weld surface appearance were tested. Microstructure and mechanical properties of CMT weld were studied. The results shaw that the thickness of interface reaction layer of the nickel- based alloy is 14. 3 μm, which is only 4. 33% of base material. The weld is made up of two phases, α-copper and iron-based solid solution. Rupture occurs initially at the welded seam near the edge of stainless steel in shear test. The maximum shear strength of the CuSi3 welded joint is 184. 9 MPa.

Simulation and experiments of ultrasonic propagation in nickel-based alloy weldments

In order to obtain good understanding of complicated beam propagation behaviors in nickel-based alloy weldments , ray tracing simulation is established to predict the ultrasonic beam path in a special welded structure of dissimilar steels. Also experimental examinations are carried out to measure the ultrasonic beam paths in the weldment. Then comparisons of the modeling predictions with experimental results are presented to reveal the complicated beam propagation behaviors.

The microscopic mechanical performance for nonuniform welded joint of nickel-based alloy with nanoindentation

To quantify the nonuniform micromechanical performance of welded joint,the load-displacement curves by nanoindentation test were introduced to examine different zones including base metal,coarse grained heat affected zone,partially melted zone,weld metal near the fusion boundary and weld metal center.The results showed that the strengthening effect of weld metal was more obvious than that of heat affected zone for nickel based welded joint and especially in coarse grained heat affected zone,the hardening resulted from overheating was not apparent.Nickel based weld metal with high content of alloying elements which were often segregated at interdendritic regions or precipitated in grain interior under nonequilibrium solidification contributed to the characteristics that differ from conventional low alloy steel welded joint.

DENDRITE REFINING AND EUTECTIC TRANSFORMATION BEHAVIOR OF NICKEL-BASE SINGLE CRYSTAL (NBSC) SUPERALLOY

Because of the low temperature gradient and growth rate, the microstructure of the conventional single crystal superalloy made by HRS processing is coarse dendrite with well developed sidebranches and has serious segregation. With the help of the high tem

Effects of heat treatment on mechanical properties of ODS nickel-based superalloy sheets prepared by EB-PVD

A Y2O3 dispersion strengthened nickel-based superalloy sheet（0.15 mm thick） was prepared by electron beam physical vapor deposition（EB-PVD） technology.Different heat treatments were used to improve the mechanical properties of the alloy sheet.Differential thermal analysis（DTA） was used to examine the thermal stability of the as-deposited sheet.Element contents,phase composition and microstructure investigations on as-deposited and heat treated specimens were performed by X-ray fluorescence spectrometer（XRF）,X-ray diffraction（XRD） and scanning electron microscopy（SEM）.Tensile tests were conducted at room temperature on specimens as-deposited and heat treated.The results show that the as-deposited sheet is composed of equiaxed grains on the substrate side and columnar grains on the evaporation side.The as-deposited sheet shows poor ductility due to micropores between columnar grains.The strength and ductility can be improved effectively by annealing at 800°C for 3 h.For samples treated at 1100°C,the strength drops down due to the precipitates of Y3Al5O12（YAG）.

Optimality analysis of multiplex A-TIG welding flux for nickel-base superalloy

Orthogonal experiment is employed to study a new kind of multiplex flux for nickel-base superalloy. This activated TIG welding flux is composed of NaF, MgF2 and CaF2, and their proportion is 5：4：1. Compared with conventional TIG welding, the penetration increases 164% by the action of the flux. Tensile test result indicates that the fracture strength of the mixed flux A-TIG weld bead is higher than base metal, and it increases along with the decrement of the welding current. The average extensibility of the weldment is beyond 100%, which means perfect ductility. MetaUographs elucidate that there exist lots of deep and evenly distributed dimples on the fiacture section of weld bead while on that of base metal there only exists a few shallow dimples and massive tearing ridge.

Review on synergistic damage effect of irradiation and corrosion on reactor structural alloys

The synergistic damage effect of irradiation and corrosion of reactor structural materials has been a prominent research focus.This paper provides a comprehensive review of the synergistic effects on the third-and fourth-generation fission nuclear energy structural materials used in pressurized water reactors and molten salt reactors.The competitive mechanisms of multiple influencing factors,such as the irradiation dose,corrosion type,and environmental temperature,are summarized in this paper.Conceptual approaches are proposed to alleviate the synergistic damage caused by irradiation and corrosion,thereby promoting in-depth research in the future and solving this key challenge for the structural materials used in reactors.

TEMPERATURE EFFECT ON LOW-CYCLE FATIGUE BEHAVIOR OF NICKEL-BASED SINGLE CRYSTALLINE SUPERALLOY

The low-cycle fatigue （LCF） behavior of a nickel-based single crystal superalloy with [001] orientation was studied at an intermediate temperature of T0℃ and a higher temperature of To ＋ 250℃ under a constant low strain rate of 10^-3 s^-1 in ambient atmosphere. The superalloy exhibited cyclic tension-compression asymmetry which is dependent on the temperature and applied strain amplitude. Analysis on the fracture surfaces showed that the surface and subsurface casting micropores were the major crack initiation sites. Interior Ta-rich carbides were frequently observed in all specimens. Two distinct types of fracture were suggested by fractogaphy. One type was characterized by Mode-I cracking with a microscopically rough surface at To ＋ 250℃. Whereas the other type at lower temperature T0℃ favored either one or several of the octahedral {111} planes, in contrast to the normal Mode-I growth mode typically observed at low loading frequencies （several Hz）. The failure mechanisms for two cracking modes are shearing of γ＇ precipitates together with the matrix at T0℃ and cracking confined in the matrix and the γ/γ＇interface at To - 250℃.