To enhance the accuracy of mechanical simulation in the directional solidification process of turbine blades for heavy-duty gas turbines,a new constitutive model that employs machine learning methods was developed.Thi...To enhance the accuracy of mechanical simulation in the directional solidification process of turbine blades for heavy-duty gas turbines,a new constitutive model that employs machine learning methods was developed.This model incorporates incremental learning and transfer learning,thus improves the predictive accuracy and generalization performance.To account for the anisotropy of the directionally solidified alloy,a deformation direction parameter is added to the model,enabling prediction of the stress-strain relationship of the alloy under different deformation directions.The predictive capabilities of both models are evaluated using correlation coefficient(R),average relative error(δ),and value of relative error(RE).Compared to the traditional model,the machine learning constitutive model achieves higher prediction accuracy and better generalization performance.This offers a new approach for the establishment of flow constitutive models for other directionally solidified and single-crystal superalloys.展开更多
The present research aims to establish a quantitative relation between microstructure and chemical composition (i.e., Ti, Al, and Nb) of newly designed nickel-based superalloys. This research attempts to identify an...The present research aims to establish a quantitative relation between microstructure and chemical composition (i.e., Ti, Al, and Nb) of newly designed nickel-based superalloys. This research attempts to identify an optimum microstructure at which the minimum quanti- fies of γ/γ' and γ/γ" compounds are achieved and the best castability is predicted. The results demonstrate that the highest quantity of inter- metallic eutectics (i.e., 41.5wt%) is formed at 9.8wt% (Ti + A1). A significant quantity of intermetallics formed in superalloy 1 (with a com- position of7 - 9.8wt% (Ti + A1)), which can deteriorate its castability. The type and morphology of the eutectics changed and the amount considerably decreased with decreasing Ti + A1 content in superalloy 2 (with a composition ofy - 7.6wt% (Ti + A1), 1.Swt% Nb). Thus, it is predicted that the castability would improve for superalloy 2. The same trend was observed for superalloy 4 (with a composition of 7 - 3.7wt% (Ti + A1), 4.4wt% Nb). This means that the amount of Laves increases with increasing Nb (to 4.4wt%) and decreasing Ti + A1 (to 3.7wt%) in su- peralloy 4. The best castability was predicted for superalloy 3 (with a composition ofy - 5.7wt% (Ti + A1), 2.8wt% Nb).展开更多
Heavy elements(X=Ta/W/Re)play an important role in the performance of superalloys,which enhance the strength,anti-oxidation,creep resistance,and anti-corrosiveness of alloy materials in a high-temperature environment....Heavy elements(X=Ta/W/Re)play an important role in the performance of superalloys,which enhance the strength,anti-oxidation,creep resistance,and anti-corrosiveness of alloy materials in a high-temperature environment.In the present research,the heavy element doping effects in FCC-Ni(γ)and Ni_(3)Al(γ')systems are investigated in terms of their thermodynamic and mechanical properties,as well as electronic structures.The lattice constant,bulk modulus,elastic constant,and dopant formation energy in non-spin,spin polarized,and spin-orbit coupling(SOC)calculations are compared.The results show that the SOC effects are important in accurate electronic structure calculations for alloys with heavy elements.We find that including spin for bothγandγ'phases is necessary and sufficient for most cases,but the dopant formation energy is sensitive to different spin effects,for instance,in the absence of SOC,even spin-polarized calculations give 1%to 9%variance in the dopant formation energy in our model.Electronic structures calculations indicate that spin polarization causes a split in the metal d states,and SOC introduces a variance in the spin-up and spin-down states of the d states of heavy metals and reduces the magnetic moment of the system.展开更多
Fracture toughness plays a vital role in damage tolerance design of materials and assessment of structural integrity.To solve these problems of com-plexity,time-consuming,and low accuracy in obtaining the fracture tou...Fracture toughness plays a vital role in damage tolerance design of materials and assessment of structural integrity.To solve these problems of com-plexity,time-consuming,and low accuracy in obtaining the fracture toughness value of nickel-based superalloys through experiments.A combination prediction model is proposed based on the principle of materials genome engineering,the fracture toughness values of nickel-based superalloys at different temperatures,and different compositions can be predicted based on the existing experimental data.First,to solve the problem of insufficient feature extraction based on manual experience,the Deep Belief Network(DBN)is used to extract features,and an attention mechanism module is introduced.To achieve the purpose of strengthen-ing the important features,an attention weight is assigned to each feature accord-ing to the importance of the feature.Then,the feature vectors obtained by the DBN module based on the Attention mechanism(A-DBN)are spliced with the original features.Thus,the prediction accuracy of the model is improved by extracting high-order combined features and low-order linear features between input and output data.Finally,the spliced feature vectors are put into the Support Vector Regression(SVR)model to further improve the regression prediction abil-ity of the model.The results of the contrast experiment show that the model can effectively improve the prediction accuracy of the fracture toughness value of nickel-based superalloys.展开更多
Laser-induced breakdown spectroscopy (LIBS) was developed to detect aluminum in nickel-based superalloys (K417, GH4033, DZ125L, З ∏742y) using a non-intensified, non-gated, low-cost detection system. The precisi...Laser-induced breakdown spectroscopy (LIBS) was developed to detect aluminum in nickel-based superalloys (K417, GH4033, DZ125L, З ∏742y) using a non-intensified, non-gated, low-cost detection system. The precision of LIBS depends strongly on the experimental conditions. The calibration curves of Al(I)394.4 nm and Al(I)396.2 nm under the optimum experimental parameters are presented. Finally the limit of detection (LOD) for aluminum is calculated from the experimental data, which is in the range of 0.09% to 0.1% by weight.展开更多
The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results th...The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results that show improved resistance to sulfidation by niobium. Research results from a current program on the role of niobium in the Russian powder metallurgy alloy EP741NP are presented. Future research plans on the role of niobium in superalloys are also discussed.展开更多
A new directionally solidified Ni-based superalloy DZ24, which is a modification of K24 alloy without rare and expensive elemental additions, such as Ta and Hf, was studied in this paper. The microstructure and stress...A new directionally solidified Ni-based superalloy DZ24, which is a modification of K24 alloy without rare and expensive elemental additions, such as Ta and Hf, was studied in this paper. The microstructure and stress rupture properties of conventionally cast and directionally solidified superalloys were comparatively analyzed. It is indicated that the microstructure of K24 alloy is composed of γ, γ', γ/γ' eutectics and MC carbides. Compared with the microstructure of K24 polycrystalline alloy, γ/γ' eutectic completely dissolves into the γ matrix, the fine and regular γ' phase reprecipitates, and MC carbides decompose to M6C/M23C6 carbides after heat treatment in DZ24 alloy. The rupture life of DZ24 alloy is two times longer than that of K24 alloy. The more homogeneous the size of γ' precipitate, the longer the rupture life. The coarsening and rafting behaviors of γ' precipitates are observed in DZ24 alloy after the stress-rupture test.展开更多
The creep and fracture behavior of the cast K417 and forged GH4049 nickel-based superalloys were investigated in the temperature range of 700-900℃ C. Within the ranges of stress and temperature studied, the steady st...The creep and fracture behavior of the cast K417 and forged GH4049 nickel-based superalloys were investigated in the temperature range of 700-900℃ C. Within the ranges of stress and temperature studied, the steady state creep rates exhibited a power law relationship with the applied stress and temperature. The time to rupture is inversely proportional to the steady state creep rate. Under all testing conditions, the creep fracture process was mainly controled by crack initiation and growth of the intergranular oxidation. Casting porosities, pores and carbides were also prefecentral locations of creep crack initiation in the cast K417 alloy. In addition, the intergranular fracture feature in the forged GH4049 alloy was apparently associated with the formation and coalescence of the cavitations on the grain boundaries.展开更多
The excessive use of nonrenewable energy has brought about serious greenhouse effect.Converting CO_(2) into high-value-added chemicals is undoubtedly the best choice to solve energy problems.Due to the excellent cost-...The excessive use of nonrenewable energy has brought about serious greenhouse effect.Converting CO_(2) into high-value-added chemicals is undoubtedly the best choice to solve energy problems.Due to the excellent cost-effectiveness and dramatic catalytic performance,nickel-based catalysts have been considered as the most promising candidates for the electrocatalytic CO_(2) reduction reaction(eCO_(2)RR).In this work,the electrocatalytic reduction mechanism of CO_(2) over Ni-based materials is reviewed.The strategies to improve the eCO_(2)RR performance are emphasized.Moreover,the research on Ni-based materials for syngas generation is briefly summarized.Finally,the prospects of nickel-based materials in the eCO_(2)RR are provided with the hope of improving transition-metal-based electrocatalysts for eCO_(2)RR in the future.展开更多
Nickel-based superalloys have been widely used in aerospace fields,especially for engine hot-end parts,because of their excellent high-temperature resistance.However,they are difficult to machine and process because o...Nickel-based superalloys have been widely used in aerospace fields,especially for engine hot-end parts,because of their excellent high-temperature resistance.However,they are difficult to machine and process because of their special properties.High-energy beam additive manufacturing(HEB-AM)of nickel-based superalloys has shown great application potential in aerospace and other fields.However,HEB-AM of nickel-based superalloys faces serious cracking problems because of the unique characteristics of superalloys,and this has become the most significant bottleneck restricting their application.In this review,the current research status related to the types,formation mechanisms,and suppression methods of cracks in nickel-based superalloys produced by HEB-AM is described.The initiation and propagation mechanisms of cracks and their multiple influencing factors are also analyzed and discussed.Then,several possible research directions to solve the cracking problems in nickel-based superalloys produced by HEB-AM are outlined.This review provides an in-depth and comprehensive understanding of the cracking problem in AM nickel-based superalloys.It also provides valuable references for AM crack-free nickel-based superalloy components.展开更多
The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindric...The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.展开更多
The conventional fabrication process for single-crystal nickel-based superalloy materials is directional solidifica-tion,which is classified as casting.With the rapid development of additive manufacturing(AM)technolog...The conventional fabrication process for single-crystal nickel-based superalloy materials is directional solidifica-tion,which is classified as casting.With the rapid development of additive manufacturing(AM)technologies,a novel process for fabricating single-crystal superalloys has become possible.This article reviews recent research on the AM of single-crystal nickel-based superalloys.Laser AM technologies,particularly directed energy deposition,are mainly used to repair single-crystal materials.Electron beam powder bed fusion is an innovative method for the direct fabrication of single-crystal materials.Accordingly,the mechanisms of single-crystal formation during AM are analyzed to elucidate the potential of this process route.Furthermore,this article discusses the challenges faced by AM for single-crystal fabrication,and provides perspectives on the trends of future developments.展开更多
Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at ...Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at high temperatures.Fusion welding serves as an effective means for joining and repairing these alloys;however,fusion welding-induced liquation cracking has been a challenging issue.This paper comprehensively reviewed recent liquation cracking,discussing the formation mechanisms,cracking criteria,and remedies.In recent investigations,regulating material composition,changing the preweld heat treatment of the base metal,optimizing the welding process parameters,and applying auxiliary control methods are effective strategies for mitigating cracks.To promote the application of nickel-based superalloys,further research on the combination impact of multiple elements on cracking prevention and specific quantitative criteria for liquation cracking is necessary.展开更多
The low-cycle fatigue (LCF) properties of DD10 (single-crystal) and DZ53 (columnar-grained) superalloys solidified by liquid-metal cooling (LMC) and high-rate solidification (HRS) processes have been systema...The low-cycle fatigue (LCF) properties of DD10 (single-crystal) and DZ53 (columnar-grained) superalloys solidified by liquid-metal cooling (LMC) and high-rate solidification (HRS) processes have been systematically investi- gated. It was found that the LCF life of DZ53 solidified by LMC was obviously better than that solidified by HRS. In contrast, for DD10, LMC showed no remarkable influences on LCF properties at high temperature and only improved LCF properties at intermediate temperature. Microstructure examination showed that the cracks generally initiated at microp- ores in the subsurface at intermediate temperature. However, the cracks occurred on the surface due to oxidation, or persistent slip bands near script-MC at high temperature. Therefore, the benefits of LMC technique can be attributed to both of the reduced casting defects which significantly affect the LCF properties at intermediate temperature and the improved microstructural homogeneity which was strongly correlated to the LCF properties of alloys at high temperature.展开更多
The evolution of microstructure and formation mechanism of incipient melting microstructure of DD5 single crystal superalloy during solution heat treatment were studied by scanning electron microscopy(SEM),electron pr...The evolution of microstructure and formation mechanism of incipient melting microstructure of DD5 single crystal superalloy during solution heat treatment were studied by scanning electron microscopy(SEM),electron probe microanalysis(EPMA),and energy dispersive spectroscopy(EDS).The solidus and liquidus of single crystal alloy were obtained by differential scanning calorimetry(DSC).Results show that the mosaic-like eutectic and fan-like eutectic are dissolved at first,and the coarseγ'phase is dissolved later during the solution heat treatment of 1,390°C/2 h+1,310°C/4 h+1,320°C/10 h+air cooling(AC).The composition segregations of Al,Ta,W and Re are 0.99,0.96,1.04 and 1.16,respectively,which close to 1.The incipient melting is caused by the low local temperature of the alloy,and the micropore region with a lower melting point is the preferred position for incipient melting.展开更多
Ni-based superalloys are one of the most important materials employed in high-temperature applications within the aerospace and nuclear energy industries and in gas turbines due to their excellent corrosion,radiation,...Ni-based superalloys are one of the most important materials employed in high-temperature applications within the aerospace and nuclear energy industries and in gas turbines due to their excellent corrosion,radiation,fatigue resistance,and high-temperature strength.Linear friction welding(LFW)is a new joining technology with near-net-forming characteristics that can be used for the manu-facture and repair of a wide range of aerospace components.This paper reviews published works on LFW of Ni-based superalloys with the aim of understanding the characteristics of frictional heat generation and extrusion deformation,microstructures,mechanical proper-ties,flash morphology,residual stresses,creep,and fatigue of Ni-based superalloy weldments produced with LFW to enable future optim-um utilization of the LFW process.展开更多
Co-Ni-based superalloys are known for their capability to function at elevated temperatures and superior hot corrosion and thermal fatigue resistance.Therefore,these alloys show potential as crucial high-temperature s...Co-Ni-based superalloys are known for their capability to function at elevated temperatures and superior hot corrosion and thermal fatigue resistance.Therefore,these alloys show potential as crucial high-temperature structural materials for aeroengine and gas turbine hot-end components.Our previous work elucidated the influence of Ti and Ta on the high-temperature mechanical properties of alloys.However,the intricate interaction among elements considerably affects the oxidation resistance of alloys.In this paper,Co-35Ni-10Al-2W-5Cr-2Mo-1Nb-xTi-(5−x)Ta alloys(x=1,2,3,4)with varying Ti and Ta contents were designed and compounded,and their oxidation resistance was investigated at the temperature range from 800 to 1000℃.After oxidation at three test conditions,namely,800℃for 200 h,900℃for 200 h,and 1000℃for 50 h,the main structure of the oxide layer of the alloy consisted of spinel,Cr_(2)O_(3),and Al_(2)O_(3)from outside to inside.Oxides consisting of Ta,W,and Mo formed below the Cr_(2)O_(3)layer.The interaction of Ti and Ta imparted the highest oxidation resistance to 3Ti2Ta alloy.Conversely,an excessive amount of Ti or Ta resulted in an adverse effect on the oxidation resistance of the alloys.This study reports the volatilization of W and Mo oxides during the oxidation process of Co-Ni-based cast superalloys with a high Al content for the first time and explains the formation mechanism of holes in the oxide layer.The results provide a basis for gaining insights into the effects of the interaction of alloying elements on the oxidation resistance of the alloys they form.展开更多
The use of high-temperature materials is especially important in power station construction, heating systems engineering, furnace industry, chemical and petrochemical industry, waste incineration plants, coal gasifica...The use of high-temperature materials is especially important in power station construction, heating systems engineering, furnace industry, chemical and petrochemical industry, waste incineration plants, coal gasification plants and for flying gas turbines in civil and military aircrafts and helicopters. Particularly in recent years, the development of new processes and the drive to improve the economics of existing processes have increased the requirements significantly so that it is necessary to change from well-proven materials to new alloys. Hitherto, heat resistant ferritic steels sufficed in conventional power station constructions for temperatures up to 550℃ newly developed ferritic/martensitic steels provide sufficient strength up to about 600 - 620℃. In new processes, e.g. fluidized-bed combustion of coal, process temperatures up to 900℃ occur. However, this is not the upper limit, since in combustion engines, e.g. gas turbines. Material temperatures up to 1100℃ are reached locally. Similar development trends can also be identified in the petrochemical industry and in the heat treatment and furnace engineering. The advance to ever higher material temperatures now not only has the consequence of having to use materials with enhanced high-strength properties, considerable attention now also has to be given to their chemical stability in corrosive media. Therefore not only examples of the use of high-temperature alloys for practical applications will be given but also be contributed to some general rules for material selection with regard to their high-temperature strength and corrosion resistance.展开更多
The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indi...The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indicate that the surface microstructure of powderschanges from dendrite into cellular stricture as the particle size of powders decrease, and thepredominant precipitates solidified on the particle surfaces were identified as MC' type carbidesenriched with Nb and Ti. It was also indicated that along with the depth of particle surfaces, thesegregation layer of S, C and O elements are thick, and that of Ti, Cr elements are thin for largesire powders while they are in reverse for median size particles.展开更多
基金supported by the National Science and Technology Major Project(2017-VII-0008-0101).
文摘To enhance the accuracy of mechanical simulation in the directional solidification process of turbine blades for heavy-duty gas turbines,a new constitutive model that employs machine learning methods was developed.This model incorporates incremental learning and transfer learning,thus improves the predictive accuracy and generalization performance.To account for the anisotropy of the directionally solidified alloy,a deformation direction parameter is added to the model,enabling prediction of the stress-strain relationship of the alloy under different deformation directions.The predictive capabilities of both models are evaluated using correlation coefficient(R),average relative error(δ),and value of relative error(RE).Compared to the traditional model,the machine learning constitutive model achieves higher prediction accuracy and better generalization performance.This offers a new approach for the establishment of flow constitutive models for other directionally solidified and single-crystal superalloys.
文摘The present research aims to establish a quantitative relation between microstructure and chemical composition (i.e., Ti, Al, and Nb) of newly designed nickel-based superalloys. This research attempts to identify an optimum microstructure at which the minimum quanti- fies of γ/γ' and γ/γ" compounds are achieved and the best castability is predicted. The results demonstrate that the highest quantity of inter- metallic eutectics (i.e., 41.5wt%) is formed at 9.8wt% (Ti + A1). A significant quantity of intermetallics formed in superalloy 1 (with a com- position of7 - 9.8wt% (Ti + A1)), which can deteriorate its castability. The type and morphology of the eutectics changed and the amount considerably decreased with decreasing Ti + A1 content in superalloy 2 (with a composition ofy - 7.6wt% (Ti + A1), 1.Swt% Nb). Thus, it is predicted that the castability would improve for superalloy 2. The same trend was observed for superalloy 4 (with a composition of 7 - 3.7wt% (Ti + A1), 4.4wt% Nb). This means that the amount of Laves increases with increasing Nb (to 4.4wt%) and decreasing Ti + A1 (to 3.7wt%) in su- peralloy 4. The best castability was predicted for superalloy 3 (with a composition ofy - 5.7wt% (Ti + A1), 2.8wt% Nb).
基金the National Key Research and Development Program of China(Grant Nos.2017YFB0701603 and 2017YFB0701502).
文摘Heavy elements(X=Ta/W/Re)play an important role in the performance of superalloys,which enhance the strength,anti-oxidation,creep resistance,and anti-corrosiveness of alloy materials in a high-temperature environment.In the present research,the heavy element doping effects in FCC-Ni(γ)and Ni_(3)Al(γ')systems are investigated in terms of their thermodynamic and mechanical properties,as well as electronic structures.The lattice constant,bulk modulus,elastic constant,and dopant formation energy in non-spin,spin polarized,and spin-orbit coupling(SOC)calculations are compared.The results show that the SOC effects are important in accurate electronic structure calculations for alloys with heavy elements.We find that including spin for bothγandγ'phases is necessary and sufficient for most cases,but the dopant formation energy is sensitive to different spin effects,for instance,in the absence of SOC,even spin-polarized calculations give 1%to 9%variance in the dopant formation energy in our model.Electronic structures calculations indicate that spin polarization causes a split in the metal d states,and SOC introduces a variance in the spin-up and spin-down states of the d states of heavy metals and reduces the magnetic moment of the system.
基金supported by Beijing Advanced Innovation Center for Materials Genome Engineering,Beijing Information Science and Technology University,Beijing Key Laboratory of Internet Culture and Digital Dissemination Research(No.ICDDXN004).
文摘Fracture toughness plays a vital role in damage tolerance design of materials and assessment of structural integrity.To solve these problems of com-plexity,time-consuming,and low accuracy in obtaining the fracture toughness value of nickel-based superalloys through experiments.A combination prediction model is proposed based on the principle of materials genome engineering,the fracture toughness values of nickel-based superalloys at different temperatures,and different compositions can be predicted based on the existing experimental data.First,to solve the problem of insufficient feature extraction based on manual experience,the Deep Belief Network(DBN)is used to extract features,and an attention mechanism module is introduced.To achieve the purpose of strengthen-ing the important features,an attention weight is assigned to each feature accord-ing to the importance of the feature.Then,the feature vectors obtained by the DBN module based on the Attention mechanism(A-DBN)are spliced with the original features.Thus,the prediction accuracy of the model is improved by extracting high-order combined features and low-order linear features between input and output data.Finally,the spliced feature vectors are put into the Support Vector Regression(SVR)model to further improve the regression prediction abil-ity of the model.The results of the contrast experiment show that the model can effectively improve the prediction accuracy of the fracture toughness value of nickel-based superalloys.
基金supported by National Natural Science Foundation of China(No.60878023)the postgraduate research and innovation project in Jiangsu province of China(No.CX10B_116Z)
文摘Laser-induced breakdown spectroscopy (LIBS) was developed to detect aluminum in nickel-based superalloys (K417, GH4033, DZ125L, З ∏742y) using a non-intensified, non-gated, low-cost detection system. The precision of LIBS depends strongly on the experimental conditions. The calibration curves of Al(I)394.4 nm and Al(I)396.2 nm under the optimum experimental parameters are presented. Finally the limit of detection (LOD) for aluminum is calculated from the experimental data, which is in the range of 0.09% to 0.1% by weight.
文摘The role of niobium in nickel-based superalloys is reviewed. The importance of niobium as a strengthener is discussed. New developments in nickel-based superalloys are also briefly mentioned, including some results that show improved resistance to sulfidation by niobium. Research results from a current program on the role of niobium in the Russian powder metallurgy alloy EP741NP are presented. Future research plans on the role of niobium in superalloys are also discussed.
文摘A new directionally solidified Ni-based superalloy DZ24, which is a modification of K24 alloy without rare and expensive elemental additions, such as Ta and Hf, was studied in this paper. The microstructure and stress rupture properties of conventionally cast and directionally solidified superalloys were comparatively analyzed. It is indicated that the microstructure of K24 alloy is composed of γ, γ', γ/γ' eutectics and MC carbides. Compared with the microstructure of K24 polycrystalline alloy, γ/γ' eutectic completely dissolves into the γ matrix, the fine and regular γ' phase reprecipitates, and MC carbides decompose to M6C/M23C6 carbides after heat treatment in DZ24 alloy. The rupture life of DZ24 alloy is two times longer than that of K24 alloy. The more homogeneous the size of γ' precipitate, the longer the rupture life. The coarsening and rafting behaviors of γ' precipitates are observed in DZ24 alloy after the stress-rupture test.
文摘The creep and fracture behavior of the cast K417 and forged GH4049 nickel-based superalloys were investigated in the temperature range of 700-900℃ C. Within the ranges of stress and temperature studied, the steady state creep rates exhibited a power law relationship with the applied stress and temperature. The time to rupture is inversely proportional to the steady state creep rate. Under all testing conditions, the creep fracture process was mainly controled by crack initiation and growth of the intergranular oxidation. Casting porosities, pores and carbides were also prefecentral locations of creep crack initiation in the cast K417 alloy. In addition, the intergranular fracture feature in the forged GH4049 alloy was apparently associated with the formation and coalescence of the cavitations on the grain boundaries.
基金support from the National Natural Science Foundation of China(52072389,52311530113)the Science and Technology Commission of Shanghai Municipality(22DZ1205600,20520760900)+2 种基金the Program of Shanghai Academic Research Leader(20XD1424300)for financial support.The authors also would like to express their gratitude to Tangshan Basic Research Funding Projects(23130210E),Hebei Province High-level Talent(Postdoctor)Funding Project(B2022003025)Key R&D projects of North China University of Science and Technology(ZD-ST-202301)Tangshan Talent Funding Project(A202202007)for their financial support.
文摘The excessive use of nonrenewable energy has brought about serious greenhouse effect.Converting CO_(2) into high-value-added chemicals is undoubtedly the best choice to solve energy problems.Due to the excellent cost-effectiveness and dramatic catalytic performance,nickel-based catalysts have been considered as the most promising candidates for the electrocatalytic CO_(2) reduction reaction(eCO_(2)RR).In this work,the electrocatalytic reduction mechanism of CO_(2) over Ni-based materials is reviewed.The strategies to improve the eCO_(2)RR performance are emphasized.Moreover,the research on Ni-based materials for syngas generation is briefly summarized.Finally,the prospects of nickel-based materials in the eCO_(2)RR are provided with the hope of improving transition-metal-based electrocatalysts for eCO_(2)RR in the future.
基金National Natural Science Foundation of China(Grant Nos.52201040,52275333)China Postdoctoral Science Foundation(Grant No.2021M701291)+2 种基金AVIC Manufacturing Technology Institute of China(Grant No.KZ571801)Hubei Provincial Department of Science and Technology 2020 Provincial Key R&D Plan of China(Grant No.2020BAB049)Wuhan Science and Technology Project of China(Grant No.2020010602012037).
文摘Nickel-based superalloys have been widely used in aerospace fields,especially for engine hot-end parts,because of their excellent high-temperature resistance.However,they are difficult to machine and process because of their special properties.High-energy beam additive manufacturing(HEB-AM)of nickel-based superalloys has shown great application potential in aerospace and other fields.However,HEB-AM of nickel-based superalloys faces serious cracking problems because of the unique characteristics of superalloys,and this has become the most significant bottleneck restricting their application.In this review,the current research status related to the types,formation mechanisms,and suppression methods of cracks in nickel-based superalloys produced by HEB-AM is described.The initiation and propagation mechanisms of cracks and their multiple influencing factors are also analyzed and discussed.Then,several possible research directions to solve the cracking problems in nickel-based superalloys produced by HEB-AM are outlined.This review provides an in-depth and comprehensive understanding of the cracking problem in AM nickel-based superalloys.It also provides valuable references for AM crack-free nickel-based superalloy components.
基金financially supported by Guangdong Province Key Field R&D Program, China (No. 2019B01 0935001)the National Nature Science Foundation of China (No. 51905192)the Fundamental Research Funds for the Central Universities (No. FRT-TP-20-006A2)
文摘The Shima yield criterion used in finite element analysis for nickel-based superalloy powder compact during hot isostatic pressing(HIP) was modified through uniaxial compression experiments. The influence of cylindrical capsule characteristics on FGH4096M superalloy powder compact deformation and densification behavior during HIP was investigated through simulations and experiments. Results revealed the simulation shrinkage prediction fitted well with the experimental shrinkage including a maximum shrinkage error of 1.5%. It was shown that the axial shrinkage was 1.7% higher than radial shrinkage for a cylindrical capsule with the size of ∮50 mm × 100 mm due to the force arm difference along the axial and radial direction of the capsule. The stress deviated from the isostatic state in the capsule led to the uneven shrinkage and non-uniform densification of the powder compact. The ratio of the maximum radial displacement to axial displacement increased from0.47 to 0.75 with the capsule thickness increasing from 2 to 4 mm. The pressure transmission is related to the capsule thickness, the capsule material performance, and physical parameters in the HIP process.
基金supported by National Key R&D Program of China(Grant No.2017YFB1103300).
文摘The conventional fabrication process for single-crystal nickel-based superalloy materials is directional solidifica-tion,which is classified as casting.With the rapid development of additive manufacturing(AM)technologies,a novel process for fabricating single-crystal superalloys has become possible.This article reviews recent research on the AM of single-crystal nickel-based superalloys.Laser AM technologies,particularly directed energy deposition,are mainly used to repair single-crystal materials.Electron beam powder bed fusion is an innovative method for the direct fabrication of single-crystal materials.Accordingly,the mechanisms of single-crystal formation during AM are analyzed to elucidate the potential of this process route.Furthermore,this article discusses the challenges faced by AM for single-crystal fabrication,and provides perspectives on the trends of future developments.
基金financially supported by the National Science and Technology Major Project of China(No.J2019-VI-0004-0117)。
文摘Nickel-based superalloys are extensively used in the crucial hot-section components of industrial gas turbines,aeronautics,and astronautics because of their excellent mechanical properties and corrosion resistance at high temperatures.Fusion welding serves as an effective means for joining and repairing these alloys;however,fusion welding-induced liquation cracking has been a challenging issue.This paper comprehensively reviewed recent liquation cracking,discussing the formation mechanisms,cracking criteria,and remedies.In recent investigations,regulating material composition,changing the preweld heat treatment of the base metal,optimizing the welding process parameters,and applying auxiliary control methods are effective strategies for mitigating cracks.To promote the application of nickel-based superalloys,further research on the combination impact of multiple elements on cracking prevention and specific quantitative criteria for liquation cracking is necessary.
基金financially supported by the National Natural Science Foundation of China under Grant Nos.51631008,51101160 and 2010CB631201
文摘The low-cycle fatigue (LCF) properties of DD10 (single-crystal) and DZ53 (columnar-grained) superalloys solidified by liquid-metal cooling (LMC) and high-rate solidification (HRS) processes have been systematically investi- gated. It was found that the LCF life of DZ53 solidified by LMC was obviously better than that solidified by HRS. In contrast, for DD10, LMC showed no remarkable influences on LCF properties at high temperature and only improved LCF properties at intermediate temperature. Microstructure examination showed that the cracks generally initiated at microp- ores in the subsurface at intermediate temperature. However, the cracks occurred on the surface due to oxidation, or persistent slip bands near script-MC at high temperature. Therefore, the benefits of LMC technique can be attributed to both of the reduced casting defects which significantly affect the LCF properties at intermediate temperature and the improved microstructural homogeneity which was strongly correlated to the LCF properties of alloys at high temperature.
基金The authors would like to express their sincere thanks to the financial support from the Key Project of National Natural Science Foundation of China(No.U16642548).
文摘The evolution of microstructure and formation mechanism of incipient melting microstructure of DD5 single crystal superalloy during solution heat treatment were studied by scanning electron microscopy(SEM),electron probe microanalysis(EPMA),and energy dispersive spectroscopy(EDS).The solidus and liquidus of single crystal alloy were obtained by differential scanning calorimetry(DSC).Results show that the mosaic-like eutectic and fan-like eutectic are dissolved at first,and the coarseγ'phase is dissolved later during the solution heat treatment of 1,390°C/2 h+1,310°C/4 h+1,320°C/10 h+air cooling(AC).The composition segregations of Al,Ta,W and Re are 0.99,0.96,1.04 and 1.16,respectively,which close to 1.The incipient melting is caused by the low local temperature of the alloy,and the micropore region with a lower melting point is the preferred position for incipient melting.
基金supported by the National Natural Science Foundation of China(Nos.52074228,52305420,and 51875470)the China Postdoctoral Science Foundation(No.2023M742830)the Xi’an Beilin District Science and Technology Planning Project,China(No.GX2349).
文摘Ni-based superalloys are one of the most important materials employed in high-temperature applications within the aerospace and nuclear energy industries and in gas turbines due to their excellent corrosion,radiation,fatigue resistance,and high-temperature strength.Linear friction welding(LFW)is a new joining technology with near-net-forming characteristics that can be used for the manu-facture and repair of a wide range of aerospace components.This paper reviews published works on LFW of Ni-based superalloys with the aim of understanding the characteristics of frictional heat generation and extrusion deformation,microstructures,mechanical proper-ties,flash morphology,residual stresses,creep,and fatigue of Ni-based superalloy weldments produced with LFW to enable future optim-um utilization of the LFW process.
基金the National Major Science and Technology Projects of China(Nos.J2019-VII-0010-0150 and J2019-VI-0009-0123)National Natural Science Foundation of China(Nos.52022011 and 52090041)+3 种基金Beijing Nova Program(No.Z211100002121170)Science Center for Gas Turbine Project(No.P2021-A-IV-001-002)Science and Technology on Advanced High Temperature Structural Materials Laboratory(No.6142903210306)Xiaomi Young Scholars Program.
文摘Co-Ni-based superalloys are known for their capability to function at elevated temperatures and superior hot corrosion and thermal fatigue resistance.Therefore,these alloys show potential as crucial high-temperature structural materials for aeroengine and gas turbine hot-end components.Our previous work elucidated the influence of Ti and Ta on the high-temperature mechanical properties of alloys.However,the intricate interaction among elements considerably affects the oxidation resistance of alloys.In this paper,Co-35Ni-10Al-2W-5Cr-2Mo-1Nb-xTi-(5−x)Ta alloys(x=1,2,3,4)with varying Ti and Ta contents were designed and compounded,and their oxidation resistance was investigated at the temperature range from 800 to 1000℃.After oxidation at three test conditions,namely,800℃for 200 h,900℃for 200 h,and 1000℃for 50 h,the main structure of the oxide layer of the alloy consisted of spinel,Cr_(2)O_(3),and Al_(2)O_(3)from outside to inside.Oxides consisting of Ta,W,and Mo formed below the Cr_(2)O_(3)layer.The interaction of Ti and Ta imparted the highest oxidation resistance to 3Ti2Ta alloy.Conversely,an excessive amount of Ti or Ta resulted in an adverse effect on the oxidation resistance of the alloys.This study reports the volatilization of W and Mo oxides during the oxidation process of Co-Ni-based cast superalloys with a high Al content for the first time and explains the formation mechanism of holes in the oxide layer.The results provide a basis for gaining insights into the effects of the interaction of alloying elements on the oxidation resistance of the alloys they form.
文摘The use of high-temperature materials is especially important in power station construction, heating systems engineering, furnace industry, chemical and petrochemical industry, waste incineration plants, coal gasification plants and for flying gas turbines in civil and military aircrafts and helicopters. Particularly in recent years, the development of new processes and the drive to improve the economics of existing processes have increased the requirements significantly so that it is necessary to change from well-proven materials to new alloys. Hitherto, heat resistant ferritic steels sufficed in conventional power station constructions for temperatures up to 550℃ newly developed ferritic/martensitic steels provide sufficient strength up to about 600 - 620℃. In new processes, e.g. fluidized-bed combustion of coal, process temperatures up to 900℃ occur. However, this is not the upper limit, since in combustion engines, e.g. gas turbines. Material temperatures up to 1100℃ are reached locally. Similar development trends can also be identified in the petrochemical industry and in the heat treatment and furnace engineering. The advance to ever higher material temperatures now not only has the consequence of having to use materials with enhanced high-strength properties, considerable attention now also has to be given to their chemical stability in corrosive media. Therefore not only examples of the use of high-temperature alloys for practical applications will be given but also be contributed to some general rules for material selection with regard to their high-temperature strength and corrosion resistance.
基金This work is financially supported by The National Defence Committee of ChineseTechnology(No.95-YJ-20)
文摘The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indicate that the surface microstructure of powderschanges from dendrite into cellular stricture as the particle size of powders decrease, and thepredominant precipitates solidified on the particle surfaces were identified as MC' type carbidesenriched with Nb and Ti. It was also indicated that along with the depth of particle surfaces, thesegregation layer of S, C and O elements are thick, and that of Ti, Cr elements are thin for largesire powders while they are in reverse for median size particles.