Improving creep strength of the fine-grained heat-affected zone of novel 9Cr martensitic heat-resistant steel via modified thermo-mechanical treatment

The infamous type Ⅳ failure within the fine-grained heat-affected zone (FGHAZ) in G115 steel weldments seriously threatens the safe operation of ultra-supercritical (USC) power plants.In this work,the traditional thermo-mechanical treatment was modified via the replacement of hot-rolling with cold rolling,i.e.,normalizing,cold rolling,and tempering (NCT),which was developed to improve the creep strength of the FGHAZ in G115 steel weldments.The NCT treatment effectively promoted the dissolution of preformed M_(23)C_(6)particles and relieved the boundary segregation of C and Cr during welding thermal cycling,which accelerated the dispersed reprecipitation of M_(23)C_(6) particles within the fresh reaustenitized grains during post-weld heat treatment.In addition,the precipitation of Cu-rich phases and MX particles was promoted evidently due to the deformation-induced dislocations.As a result,the interacting actions between precipitates,dislocations,and boundaries during creep were reinforced considerably.Following this strategy,the creep rupture life of the FGHAZ in G115 steel weldments can be prolonged by 18.6%,which can further push the application of G115 steel in USC power plants.

Surface Nanocrystallization of Steel 20 Induced by Fast Multiple Rotation Rolling

In order to expand the application of steel 20 in precision device,fast multiple rotation rolling( FMRR) is applied to fabricate a nanostructured layer on the surface of steel 20. The FMRR samples are then Cr-Rare earth-boronized under low-temperature. The microstructure of the top surface layer is characterized by transmission electron microscopy( TEM). Microhardness of the top surface is measured by a Vickers microhardness tester. The boride layer is characterized by using scanning electron microscopy( SEM).Experimental results show that a nanostructured layer with their grain size range from 200 to 400 nm is obtained in the top surface layer. The microhardness of FMRR sample changes gradiently along the depth from about274 HV in the top surface layer to about 159 HV in the matrix,which is nearly 1.7 times harder than that of the original sample. The penetrating rate is enhanced significantly when the FMRR samples are Cr-Rare earthboronized at 600 ℃ for 6 h. Thickness of the boride layer increases to around 20 μm,which is nearly twice thicker than that of the original sample.

Study of welding technology on Baosteel high-strength heavy steel Bweldy620QL6

This study aims to conduct the weldability test for a high-strength structural steel, Bweldy620QL6, developed by Baosteel. This steel was subjected to welding,and the effects of two kinds of shielding gas,a binary gas of 80% Ar ＋ 20% CO, and ternary gas of 90% Ar ＋ 8% CO, ＋ 2% O2, on the performance of the welded joints of high-strength heavy steel were compared. The results show that Bweldy620QL6 has good weldability,and the joints obtained using binary gas and ternary gas meet common requirements.

Nonlinear Study on the Mechanical Performance of Built-Up Cold-Formed Steel Concrete-Filled Columns under Compression

Given their numerous functional and architectural benefits,such as improved bearing capacity and increased resistance to elastic instability modes,cold-formed steel(CFS)built-up sections have become increasingly developed and used in recent years,particularly in the construction industry.This paper presents an analytical and numerical study of assembled CFS two single channel-shaped columns with different slenderness and configurations(backto-back,face-to-face,and box).These columns were joined by double-row rivets for the back-to-back and box configurations,whereas they were welded together for the face-to-face design.The built-up columns were filled with ordinary concrete of good strength.Finite element models were applied,using ABAQUS software,to assess mechanical performance and study the influence of assembly techniques on the behavior of cold-formed columns under axial compression.Analytical approaches based on Eurocode 3 and Eurocode 4 recommendations for un-filled and concrete-filled columns respectively were followed for the numerical analysis,and concrete confinement effects were also considered per American Concrete Institute(ACI)standards for face-to-face and box configurations.The obtained results indicated a good correlation between the numerical results and the proposed analytical methodology which did not exceed 8%.The failure modes showed that the columns failed due to instabilities such as local and global buckling.

Prospects for green steelmaking technology with low carbon emissions in China

The steel industry is a major source of CO_(2) emissions,and thus,the mitigation of carbon emissions is the most pressing challenge in this sector.In this paper,international environmental governance in the steel industry is reviewed,and the current state of development of low-carbon technologies is discussed.Additionally,low-carbon pathways for the steel industry at the current time are proposed,emphasizing prevention and treatment strategies.Furthermore,the prospects of low-carbon technologies are explored from the perspective of transitioning the energy structure to a“carbon-electricity-hydrogen”relationship.Overall,steel enterprises should adopt hydrogen-rich metallurgical technologies that are compatible with current needs and process flows in the short term,based on the carbon substitution with hydrogen(prevention)and the CCU(CO_(2) capture and utilization)concepts(treatment).Additionally,the capture and utilization of CO_(2) for steelmaking,which can assist in achieving short-term emission reduction targets but is not a long-term solution,is discussed.In conclusion,in the long term,the carbon metallurgical process should be gradually supplanted by a hydrogen-electric synergistic approach,thus transforming the energy structure of existing steelmaking processes and attaining near-zero carbon emission steelmaking technology.

Bulging Distortion of Austenitic Stainless Steel Sheet on the Partially Penetrated Side of Non-Penetration Lap Laser Welding Joint

Non-penetration laser welding of lap joints in austenitic stainless steel sheets is commonly preferred in fields where the surface quality is of utmost importance.However,the application of non-penetration welded austenitic stainless steel parts is limited owing to the micro bulging distortion that occurs on the back surface of the partial penetration side.In this paper,non-penetration lap laser welding experiments,were conducted on galvanized and SUS304 austenitic stainless steel plates using a fiber laser,to investigate the mechanism of bulging distortion.A comparative experiment of DC01 galvanized steel-Q235 carbon steel lap laser welding was carried out,and the deflection and distortion profile of partially penetrated side of the sheets were measured using a noncontact laser interferometer.In addition,the cold-rolled SUS304 was subjected to heat holding at different temperatures and water quenching after bending to characterize its microstructure under tensile and compressive stress.The results show that,during the heating stage of the thermal cycle of laser lap welding,the partial penetration side of the SUS304 steel sheet generates compressive stress,which extrudes the material in the heat-affected zone to the outside of the back of the SUS304 steel sheet,thereby forming a bulge.The findings of these experiments can be of great value for controlling the distortion of the partial penetrated side of austenitic stainless steel sheet during laser non-penetration lap welding.

Micropores in G20Mn5N cast steel and their influence on stress distribution

To accurately analyze the impact of casting pores in steel,high-resolution 3D X-ray tomography technology was used to gather detailed statistical information about micropores.These micropores were classified as gas,shrinkage,and gas-shrinkage pores depending on their formation origin and morphology.Clustering tendencies and affinity parameters were defined to characterize the spatial correlations among these three types of pores.The 3D data from X-ray tomography scans were then integrated into finite element analysis(FEA)software to predict how micropore shape,size,and distribution influence stress distribution within the material.The results show that certain inflection points with small local radii within the cast pores are major contributors to stress concentration.Therefore,cast pores cannot be simply modeled as ideal spherical pores.The sphericity and volume of pores have a significant impact on the stress concentration of the model.Specifically,lower sphericity and larger pore volumes result in higher stress concentrations.Moreover,the internal pores of steel castings exhibit specific global distribution characteristics.Pores located on the surface of the specimen lead to significantly higher stress concentrations compared to those located inside the specimen.

Novel wood-plastic composite fabricated via modified steel slag:Preparation,mechanical and flammability properties

A novel method was developed to enhance the utilization rate of steel slag(SS).Through treatment of SS with phosphoric acid and aminopropyl triethoxysilane(KH550),we obtained modified SS(MSS),which was used to prepare MSS/wood-plastic composites(MSS/WPCs)by replacing talcum powder(TP).The composites were fabricated through melting blending and hot pressing.Their mechanical and combustion properties,which comprise heat release,smoke release,and thermal stability,were systematically investigated.MSS can improve the mechanical strength of the composites through grafting reactions between wood powder and thermoplastics.Notably,MSS/WPC#50(16wt%MSS)with an MSS-to-TP mass ratio of 1:1 exhibited optimal comprehensive performance.Compared with those of WPC#0 without MSS,the tensile,flexural,and impact strengths of MSS/WPC#50 were increased by 18.5%,12.8%,and 18.0%,respectively.Moreover,the MSS/WPC#50 sample achieved the highest limited oxygen index of 22.5%,the highest vertical burning rating at the V-1 level,and the lowest horizontal burning rate at 44.2 mm/min.The formation of a dense and stable char layer led to improved thermal stability and a considerable reduction in heat and smoke releases of MSS/WPC#50.However,the partial replacement of TP with MSS slightly compromised the mechanical and flame-retardant properties,possibly due to the weak grafting caused by SS powder agglomeration.These findings suggest the suitability of MSS/WPCs for high-value-added applications as decorative panels indoors or outdoors.

Novel Brick Technology for Carbon Reduction Footprint in Steel Shop Linings

Clean steel encompasses a multitude of concepts that are based on fulfilling customer requirements and can be produced in many ways depending on the existing equipment and detailed customer demands.A common feature of all clean steel production is tight process control along with continuous monitoring.To meet an increasing demand for cold-rolled(CR)steel sheets of improved mechanical properties,and to cope with the change of the annealing process from a batch-type to a continuous process,it is necessary to establish a technique for making ultralow carbon(ULC)steel with a C-concentration lower than 20 ppm for the steelmaking process associated with a major challenge to guarantee the competitiveness with observance of environmental requirements.Steel ladle lining plays an important role on the energy consumption during the production and the refractory lining design contributes to minimize thermal bath loss,carbon pick up and shell temperature.A new generation of unfired zero carbon refractories was developed with two specific approaches:(1)replacement of firing bricks reducing CO_(2) footprint and(2)replacement of carbon containing with performance increasing.Bricks can be used in working and safety linings with a unique microstructure with better heat scattering and similar thermomechanical properties.This work presents customers’performance compared to traditional products highlighting energy savings.

Study on Key Joining Technology and Test Method of Steel/Al Hybrid Structure Body-in-White

Green and low carbon promote the application and development of light-weight materials in body-in-white. Large-scale die-casting Al alloy (DCAA) and high-strength thermo-formed steel sheet (TFSS) have put forward higher requirements for the application of joining technology of high-strength steel/Al dissimilar materials. Taking the new die-casting Al alloy body as an example, this paper systematically studies the progress of the latest joining methods of steel/Al dissimilar material with combination of two-layer plate and three-layer plate. By analyzing the joining technologies such as FSPR, RES, FDS and SPR, the technology and process characteristics of steel/Al dissimilar material joining are studied, and the joining technical feasibility and realization means of different material combination of the body are analyzed. The conditions of material combination, material thickness, material strength, flange height, preformed holes and joint spacing for achieving high-quality joining are given. The FSPR joining technology is developed and tested in order to meet with the joining of parts with DCAA and TFSS, especially for the joining of three-layer plates with them. It finds the method and technical basis for the realization of high quality joining of dissimilar materials, provides the early conditions for the application of large DCAA and TFSS parts in body-in-white, and meets the design requirements of new energy body. .

基于Voronoi法的120方坯拉矫过程微晶塑性演化数值模拟研究

结合拉坯矫直机现场实际工况,基于Voronoi法建立了方坯拉矫过程钢坯三维随机微晶模型,通过纳米压痕实验统计晶粒异质性信息确定晶粒异质性特性并划分晶粒类型,由晶粒异质性系数确定各类晶粒材料属性。基于Python脚本编程将不同材料属性按概率随机赋予Voronoi元胞。建立了考虑晶粒异质性的SUS301L-HT不锈钢方坯拉矫过程热力耦合微晶模型,计算并揭示了拉坯矫直过程温度场、应力场瞬时演化规律。结果表明:考虑晶粒异质性模型能更好地揭示拉坯矫直过程温度场、应力场的不均匀性分布状态,尤其是钢坯相邻晶粒边界处的应力会发生突变,且随着晶粒间力学性能差异越大,突变现象越显著。基于Voronoi法建立考虑晶粒异质性的拉坯矫直数值模型可有效反馈拉坯矫直过程中微观演化机理。

基于转录组学分析Xenorhabdus bovienii肽基脯氨酰异构酶ppia-l20基因的表达调控

[目的]前期从广谱抗菌的Xenorhabdus bovienii NN6菌株的胞外蛋白中分离出一种新型杀菌蛋白PPIA-L20,为肽基脯氨酰异构酶A类似物,该蛋白能够抑制尖孢镰刀菌西瓜专化型的孢子的萌发,致使孢子死亡。经过多次试验验证ppia-l20基因的表达水平不稳定,与发酵时间没有明显的相关性。本文旨在探寻调控ppia-l20基因表达的调控因子,进而推测ppia-l20基因表达调控的分子机制,为进一步提高抗菌蛋白的产量提供参考。[方法]对ppia-l20的转录水平进行Real-time PCR分析并与菌株生长曲线进行相关性分析,选择ppia-l20基因表达量差异显著的2个发酵时间点进行转录组学比较,并对表达差异显著的DEG(differential expressed gene)进行GO功能注释、KEGG富集通路和蛋白网络互作分析。[结果]4~84 h发酵菌体中的ppia-l20基因表达趋势不稳定,其转录水平与时间不相关。与ppia-l20低表达量的8 h发酵菌体相比,ppia-l20高表达量的12 h发酵菌体中有466个DEG,包括193个上调基因和273个下调基因。Real-time PCR验证表明基因表达差异趋势与转录组测序结果一致,证明测序结果可信。对差异表达的基因进行GO功能注释、KEGG富集分析,发现DEG的功能与膜形成相关,富集通路与双组分调节系统、磷酸转移酶系统和阳离子抗菌肽抵制通路相关。其中,双组分调节系统中的qseC基因和opmR基因表达量均上调2倍,ppia-l20基因位于阳离子抗菌肽抵制通路,该通路上的nlpE基因(负责编码外膜脂蛋白)显著下调。蛋白互作网络中,PPIA-L20蛋白与位于外膜的AMP结合蛋白TycC、GrsB有互作关系,NlpE蛋白与双组分调节系统中cpxR基因、cpxA基因表达的蛋白有互作关系。[结论]Xenorhabdus bovienii NN6菌株可能通过双组分调节系统通路、阳离子抗菌肽抵制通路上的关键基因nlpE和磷酸转移酶系统共同调控ppia-l20的表达。

Phenomenological modelling of flow behaviour of 20MnMoNi55 reactor pressure vessel steel at cryogenic temperature with different strain rates

In the present study a phenomenological constitutive model is developed to describe the flow behaviour of 20MnMoNi55 low carbon reactor pressure vessel (RPV) steel at sub-zero temperature under different strain rates. A set of uniaxial tensile tests is done with the variation of strain rates and temperature ranging from 10^-4s^-1 to 10^-1s^-1 and -80℃ to 140℃ respectively. From the experimental data, family of flow curves at different temperatures and strain rates are generated and fitted exponentially. The strain rate and temperature dependence of the coefficients of the exponential flow curves are extracted from these curves and characterised through a general phenomenological constitutive coupled equation. The coefficients of this coupled equation are optimised using genetic algorithm. Finite element simulation of tensile tests at different strain rates and temperatures are done using this coupled equation in material model of Abaqus FEA software and validated with experimental results. The novelties of proposed model are:(a) it can predict precisely the flow behaviour of tensile tests (b) it is a simple form of equation where fitting parameters are both function of strain rate ratio and temperature ratio,(c) it has ability to characterize flow behaviour with decreasing subzero temperatures and increasing strain rates.

Quickly obtaining densely dispersed coherent particles in steel matrix and its related mechanical property

Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.

Defect Inspection Technology for Steel Truss Suspension Bridges

Steel truss suspension bridges are prone to developing defects after prolonged use.These defects may include corrosion of the main cable or the steel truss.To ensure the normal and safe functioning of the suspension bridge,it is necessary to inspect for defects promptly,understand the cause of the defect,and locate it through the use of inspection technology.By promptly addressing defects,the suspension bridge’s safety can be ensured.The author has analyzed the common defects and causes of steel truss suspension bridges and proposed specific inspection technologies.This research is intended to aid in the timely discovery of steel truss suspension bridge defects.

Electronic structure and ultraviolet spectra of p-C_(6)H_(4)-C_(20)

Geometry optimization of p-C_(6)H_(4)-connected cyclo[20]carbon(p-C_(6)H_(4)-C_(20))was carried out at M062X/6-311G(d,p)level,three kinds of bond orders(Mayer,Laplacian,and Wiberg),electron-hole distributions,localized orbital locators(LOL),and infrared(IR)spectrum were also performed at the same level.Based on TD-DFT M062X/6-311G(d,p)method,the first 20 excited states and ultraviolet(UV)spectra of p-C_(6)H_(4)-C_(20) were calculated.Calculation results of π-electron delocalization analyses prove thatπ-electron delocalization of p-C_(6)H_(4)-C_(20) is more likely to occur on shorter C-C bonds rather than longer C-C bonds,and inside/outside of the ring plane rather than above/below the ring plane.Two absorption peaks of p-C_(6)H_(4)-C_(20) locate at about 319 nm and 236 nm,respectively.

Preparation of 20 (S)-protopanaxadiol PLGA Nanoparticles

[Objectives]To prepare 20(S)-protopanaxadiol PLGA nanoparticles(20(S)-PPD-PLGA-NPs).[Methods]20(S)-PPD-PLGA-NPs were prepared by emulsion solvent evaporation method,and the optimal formulation was screened by Box-Behnken experiment with particle size and drug loading as the indicators through single factor experiment,and the drug release in vitro was carried out.[Results]The average diameter of the nanoparticles was(119.60±2.29)nm and the polydispersity index was(0.12±0.02),the size was uniform.The encapsulation efficiency and drug loading of protopanaxadiol were(87.99±1.29)%and(14.86±0.25)%,respectively.[Conclusions]The 20(S)-PPD-PLGA-NPs were successfully prepared by emulsion solvent evaporation method,and the 20(S)-PPD-PLGA-NPs had good stability,to lay a foundation for the study of 20(S)-PPD-PLGA-NPs in vitro and in vivo.

Enhancement of endogenous midbrain neurogenesis by microneurotrophin BNN-20 after neural progenitor grafting in a mouse model of nigral degeneration

We have previously shown the neuroprotective and pro-neurogenic activity of microneurotrophin BNN-20 in the substantia nigra of the“weaver”mouse,a model of progressive nigrostriatal degeneration.Here,we extended our investigation in two clinically-relevant ways.First,we assessed the effects of BNN-20 on human induced pluripotent stem cell-derived neural progenitor cells and neurons derived from healthy and parkinsonian donors.Second,we assessed if BNN-20 can boost the outcome of mouse neural progenitor cell intranigral transplantations in weaver mice,at late stages of degeneration.We found that BNN-20 has limited direct effects on cultured human induced pluripotent stem cell-derived neural progenitor cells,marginally enhancing their differentiation towards neurons and partially reversing the pathological phenotype of dopaminergic neurons generated from parkinsonian donors.In agreement,we found no effects of BNN-20 on the mouse neural progenitor cells grafted in the substantia nigra of weaver mice.However,the graft strongly induced an endogenous neurogenic response throughout the midbrain,which was significantly enhanced by the administration of microneurotrophin BNN-20.Our results provide straightforward evidence of the existence of an endogenous midbrain neurogenic system that can be specifically strengthened by BNN-20.Interestingly,the lack of major similar activity on cultured human induced pluripotent stem cell-derived neural progenitors and their progeny reveals the in vivo specificity of the aforementioned pro-neurogenic effect.

Running States of China's Iron & Steel,Nonferrous,and Building Materials Industries in 2012

Iron ＆ Steel Industry China＇s outputs of crude steel, steel products, coke and ferrous alloys in 2012 were 716.54 million tons （up 3.1% YOY）, 051.86 million tons （up 7.7% YOY）, 443.23 million tons （up 5.2% YOY） and 31.29 million tons （up 15% YOY）,

N_2O_5/HNO_3硝化硝解TAIW制备CL-20

以2,6,8,12-四乙酰基-2,4,6,8,10,12-六氮杂四环[5,5,0,03,1105,9]十二烷(TAIW)为原料,利用硝化剂N2O5在HNO3介质中硝化硝解TAIW制得CL-20。该方法可避免浓H2SO4污染,最佳反应条件为:反应温度为40℃,反应时间为1 h,n(TAIW)∶n(N2O5)∶n(HNO3)=1∶4∶36,产率为86.1%,纯度达到99%。产物经元素分析、核磁共振、质谱等测试技术对其结构进行了检测和表征。