Intense up-conversion emissions of yb3＋/Dy3＋ co-doped A12O3 nanopowders prepared by non-aqueous sol-gel method＊

yb3＋/Dy3＋ co-doped A1203 nanopowders have been prepared by the non-aqueous sol-gel method and their up- conversion photoluminescence spectra are measured under excitation by a 980-nm semiconductor laser. The results show that there are comparatively abundant spectra of up-conversion emissions centered at 378, 408, 527 and 543, and 663 nm, corresponding to 4C9/2→ 6H13/2, 4C9/2→ 6Hll/2, 4115/2 → 6H13/2, and 4F9/2 →6Hll/2 transitions of Dy3＋, respectively. Two-photon and three-photon processes are involved in ultraviolet, violet, green, and red up-conversion emissions. The energy transition between Yb3＋ and Dy3＋ is discussed.

Tetrathiafulvalene esters with high redox potentials and improved solubilities for non-aqueous redox flow battery applications

The exploitation of high performance redox-active substances is critically important for the development of non-aqueous redoxflow batteries.Herein,three tetrathiofulvalene(TTF)derivatives with different substitution groups,namely TTF diethyl ester(TTFDE),TTF tetramethyl ester(TTFTM),and TTF tetraethyl ester(TTFTE),are prepared and their energy storage properties are evaluated.It has been found that the redox potential and solubility of these TTF derivatives in conventional carbonate electrolytes increases with the number of ester groups.The battery with a catholyte of 0.2 mol L^(-1) of TTFTE delivers a specific capacity of more than 10 Ah L^(-1) at the current density of 0.5 C with two discharge voltage platforms locating at as high as 3.85 and 3.60 V vs.Li/Liþ.Its capacity retention can be improved from 2.34 Ah L^(-1) to 3.60 Ah L^(-1) after 100 cycles by the use of an anion exchange membrane to block the crossover of TTF species.The excellent cycling stability of the TIF esters is supported by their well-delocalized electrons,as revealed by the density function theory calculations.Therefore,the introduction of more and larger electron-withdrawing groups is a promising strategy to simultaneously increase the redox-potential and solubility of redox-active ma-terials for non-aqueous redoxflow batteries.

Design of the reactive dyes containing large planar multi-conjugated systems and their application in non-aqueous dyeing

The development of pollution-free dyeing technology, including anhydrous dyeing and non-aqueous dyeing technologies, has always been an important way and research hot in energy conservation and emission reduction. Designing new structural dye molecules is the key to water-saving dyeing processes.Herein, three reactive dyes were designed and synthesized, which contained large planar multiconjugated systems and multi-reactive groups. The designed reactive dyes are expected to have high affinity and high fixations in non-aqueous or small bath dyeing processes. The reactive dyes were applied in the decamethylcyclopentasiloxane(DMCS) reverse micelle dyeing for cotton fabric. High exhaustion rate of 99.35%, 98.10% and 98.80%, and fixation rate of 95.15%, 96.34% and 94.40% for three dyes, R1,R2 and R3, could be respectively obtained. The dyes can be fully utilized and had excellent dyeing performance, fastness and levelling properties under the revere micelle dyeing. The cotton fabric is like an oil-water separator in the dyeing process, where the dye micelles rapidly absorb and permeate into the cotton fibers. DMCS circulates around the fabric to transfer mass and energy. After dyeing, the solvent can be separated quickly and reused. The new reactive dyes containing large planar and multi-conjugated systems have potential application in green and sustainable dyeing technology with less wastewater and higher utilization.

Analyses of non-aqueous reactive polymer insulation layer in high geothermal tunnel

The scenario of geothermal tunnel is commonly observed around the world,and increases with the new constructions in the long and deep tunnels,for example in China.Tunnel insulation is generally divided into active and passive insulation.In passive insulation,it is an effective way to set low thermal con-ductivity materials as the thermal insulation layer as the choice of insulation material mainly depends on the thermal conductivity.Polymer is a kind of material with good geothermal performance,but there are relatively few studies.In this context,the transient plane source(TPS)method was used to measure the thermal conductivity of the developed polymer.Then,the temperature field of the high geothermal tunnel insulated by the non-aqueous reactive polymer layer was simulated.With the parametric analysis results,the suggestions for the tunnel layers were proposed accordingly.It revealed that the thermal conductivity of polymer first increases and then decreases with temperature.There are two rising sec-tions(?40e10?C and 20e90?C),one flat section(10e20?C)and one descending section(>90?C).It is observed the thermal conductivity of polymer increases with increase of the density of insulation layer and the density,and the thermal conductivity decreases when exposed to high temperatures.The temperature of the surrounding rocks increases with increase of the thermal conductivity and the thickness of polymer.Finally,a more economical thickness(5 cm)was proposed.Based on the parametric study,a thermal insulation layer with thermal conductivity less than 0.045 W/(m K),thickness of 5 cm and a density less than 0.12 g/cm 3 is suggested for practice.

Development of Modified Glasses by Transparent, Functional Hybrid Sol-Gel Nano-Ceramic Coatings, a Comparative Study

This paper concentrates on the development of glasses with self-cleaning surfaces exhibiting high water contact angles. In this study, we prepared super-hydrophobic nano-ceramic coated glass based on titania & silica using simple sol-gel & dip coating methods and studied the best composition of the coatings by altering ratios of titanium tetraisopropoxide (TTIP)/tetraethyl orthosilicate (TEOS) with different homogenizing agents. We characterized the coatings by surface roughness measurement, percentage of optical transmission, static contact angle, near-infrared (NIR) transmission, and diffuse reflectance. The fabrication of coatings on glass substrates played an important role in increasing the water contact angle of about 95° and visible & NIR transmission of about 90%. We compared our modified glass substrate with commercial low emissivity (Low E) glass using X-ray diffraction (XRD) analysis, which showed pure amorphous surface claiming excellent wettability and thus the prepared glass substrate could have a variety of applications in different fields.

Non-aqueous lithium bromine battery of high energy density with carbon coated membrane

Flow batteries with high energy density and long cycle life have been pursued to advance the progress of energy storage and grid application. Non-aqueous batteries with wide voltage windows represent a promising technology without the limitation of water electrolysis, but they suffer from low electrolyte concentration and unsatisfactory battery performance. Here, a non-aqueous lithium bromine rechargeable battery is proposed, which is based on Br;/Br;and Li;/Li as active redox pairs, with fast redox kinetics and good stability. The Li/Br battery combines the advantages of high output voltage（;.1 V）,electrolyte concentration（3.0 mol/L）, maximum power density（29.1 m W/cm;） and practical energy density（232.6 Wh/kg）. Additionally, the battery displays a columbic efficiency（CE） of 90.0%, a voltage efficiency（VE） of 88.0% and an energy efficiency（EE） of 80.0% at 1.0 m A/cm;after continuously running for more than 1000 cycles, which is by far the longest cycle life reported for non-aqueous flow batteries.

Modeling Non-aqueous Phase Liquid Displacement Process

A pore-network model physically based on pore level multiphase flow was used to study the water-non-aqueous phase liquid （NAPL） displacement process, especially the effects of wettability, water-NAPL interracial tension, the fraction of NAPL-wet pores, and initial water saturation on the displacement. The computed data show that with the wettability of the mineral surfaces changing from strongly water-wet to NAPL-wet, capillary pressure and the NAPL relative permeability gradually decrease, while water-NAPL interfacial tension has little effect on water relative permeability, but initial water saturation has a strong effect on water and NAPL relative permeabilities. The analytical results may help to understand the micro-structure displacement process of non-aqueous phase liquid and to provide the theoretical basis for controlling NAPL migration.

Organic Electrode Materials for Non-aqueous K-Ion Batteries

The demands for high-performance and low-cost batteries make K-ion batteries(KIBs) considered as promising supplements or alternatives for Li-ion batteries(LIBs). Nevertheless, there are only a small amount of conventional inorganic electrode materials that can be used in KIBs, due to the large radius of K^+ ions. Diff erently, organic electrode materials(OEMs) generally own sufficiently interstitial space and good structure flexibility, which can maintain superior performance in K-ion systems. Therefore, in recent years, more and more investigations have been focused on OEMs for KIBs. This review will comprehensively cover the researches on OEMs in KIBs in order to accelerate the research and development of KIBs. The reaction mechanism, electrochemical behavior, etc., of OEMs will all be summarized in detail and deeply. Emphasis is placed to overview the performance improvement strategies of OEMs and the characteristic superiority of OEMs in KIBs compared with LIBs and Na-ion batteries.

Systematic approaches to improving the performance of polyoxometalates in non-aqueous redox flow batteries

Polyoxometalates have been explored as multi-electron active species in both aqueous and non-aqueous redox flow batteries. Although non-aqueous systems in principle offer a wider voltage window for redox flow battery operation, realization of this potential requires a judicious choice of solvent as well as polyoxometalate properties. We demonstrate here the superior performance of N,N-dimethylformamide(DMF)compared to acetonitrile as a solvent for redox flow batteries based on Li3PMo12O40. This compound displays two 1-electron transfers in acetonitrile but can access an extra quasi-reversible 2-electron redox process in DMF. A cell containing 10 mM solution of Li3PMo12O40 in DMF produced a cell voltage of 0.7 V with 2-electron transfers(State of Charge = 60%) and showed a good cyclability. As a means to boost energy density, operation of the redox flow battery at a higher concentration of 0.1 M Li3PMo12O40 produced cells with cell voltage of 0.6 V in acetonitrile and a cell voltage of 1.0 V in DMF;both showed excellent coulombic efficiencies of more than 90% over the course of 30 cycles. Energy density was also increased by employing an asymmetric cell with different polyoxometalates on each side to extend cell voltage.Li6P2W18O62 exhibited 3 quasi-reversible 2-electron transfers in the potential range between-2.05 V and-0.5 V vs. Ag/Ag+. 10 mM Li6P2W18O62/Li3PMo12O40 in DMF produced a cell with cell voltage of 1.3 V involving 4-electron transfers(State of Charge = 50%) with coulombic efficiency of nearly 100% and energy efficiency of nearly 70% throughout the test with more than 20 cycles. These promising results demonstrate proof-of-concept approaches to improving the performance of polyoxometalates in non-aqueous redox flow batteries.

Vesicle Formation from Equimolar Cationic-anionic Surfactant Mixture in Non-aqueous Media

Unilamellar vesicles from the mixtures of 1:1 sodium 10-undecenoate and trimethyl[2-(10-undecenoyloxy)ethyl]ammonium iodide in the mixed solvents of ethanol and heptane can be formed spontaneously or by sonication. They can exist in the variation of concentrations and volume ratios of ethanol to heptane, which indicates to some extent the high capability of vesicle formation in such mixed systems.

In-situ Characterization of Non-aqueous Nano-dispersion Systems by Freeze-etching TEM and Comparative Study with Laser Scattering Method

In-situ characterization of non-aqueous nano-dispersion systems（NANDS） by freeze-etching transmission electron microscope（FETEM） was reported.To improve just-for-once successive rate of specimen preparation and get good characterization results,an improving specimen preparation method of freezing etching was developed.Size,distribution and morphology of NANDS were directly visualized.Some information of particle dispersion feature and particle density can also be obtained.Reproductivity of the FETEM characterization is excellent.Comparing with laser scattering method,which is liable to give positive error especially for small size particle anchoring disperser,FETEM characterization can give more accurate measurement of particle size.Moreover,FETEM can give dispersion feature of nanoparticle in non-aqueous medium.

Determination of Roxithromycin Tablets by Capillary Electrophoresis Employing Non-aqueous Media with Square-wave Amperometric Detection

A new method of determination for roxithromycin tablets by non-aqueous capillary electrophoresis (NACE) with square-wave amperometric detection was carried out. Several parameters affecting the NACE-AD determination were studied. The data was modified by spline wavelet least square (SWLS). The method is simple, rapid and highly reliable for routine analysis.

Thermodynamic solvation of a series of homologous α-amino acids in non-aqueous mixture of ethylene-glycol and N,N-dimethyl formamide

Standard free energies (ΔG0t(i) ) and entropies (ΔS0t(i)) of transfer of some homologous α-amino acids viz. glycine (gly), dl-alanine (ala), dl-α-amino butyric acid (aba) and dl-nor-valine (nor-val) from protic ethylene glycol (EG) to dipolar aprotic N,N-dimethyl formamide (DMF) have been evaluated from solubility measure-ments at five equidistant temperatures i.e from 15 to 350C. The observed ΔG0t(i) and TΔS0t(i) Vs composition profiles are complicated because of the various interaction effects. The chemical effects of the transfer Gibbs energies (ΔG0t.ch(i)) and entropies of transfer (ΔS0t.ch(i)) have been obtained after elimination of cavity effect, estimated by the scaled particle theory and dipole-dipole interaction effects, estimated by the use of Keesom-orientation expression. The chemical contributions of transfer energetics of homologous α-amino acids are guided by the composite effects of increased dispersion interaction, basicity and decreased acidity, hydrogen bonding effects and solvophobic solvation of ethylene glycol and N, N-dimethyl formamide mixed solvent as compared to that of reference solvent (ethylene glycol).

Sol-gel-based porous Ti-doped tungsten oxide films for high-performance dual-band electrochromic smart windows

Dual-band electrochromic smart windows(DESWs)with independent control of the transmittance of near-infrared and visible light show great potential in the application of smart and energy-saving buildings.The current strategy for building DESWs is to screen materials for composite or prepare plasmonic nanocrystal films.These rigorous preparation processes seriously limit the further development of DESWs.Herein,we report a facile and effective sol-gel strategy using a foaming agent to achieve porous Ti-doped tungsten oxide film for the high performance of DESWs.The introduction of foaming agent polyvinylpyrrolidone during the film preparation can increase the specific surface area and free carrier concentration of the films and enhance their independent regulation ability of near-infrared electrochromism.As a result,the optimal film shows excellent dual-band electrochromic properties,including high optical modulation(84.9%at 633 nm and 90.3%at 1200 nm),high coloration efficiency(114.9 cm^(2) C^(-1) at 633 nm and 420.3 cm^(2) C^(-1) at 1200 nm),quick switching time,excellent bistability,and good cycle stability(the transmittance modulation losses at 633 and 1200 nm were 11%and 3.5%respectively after 1000 cycles).A demonstrated DESW fabricated by the sol-gel film showed effective management of heat and light of sunlight.This study represents a significant advance in the preparation of dual-band electrochromic films,which will shed new light on advancing electrochromic technology for future energy-saving smart buildings.

Investigation of UV photosensor properties of Al-doped SnO_(2) thin films deposited by sol-gel dip-coating method

Transparent conducting aluminum doped tin oxide thin films were prepared by sol-gel dip coating method with differ-ent Al concentrations and characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), UV-Vis spectrophotometry and photoconductivity study. The variation observed in the properties of the measured films agrees with a difference in the film's thickness, which decreases when Al concentration augments. X-ray diffraction analysis reveals that all films are polycrystal-line with tetragonal structure, (110) plane being the strongest diffraction peak. The crystallite size calculated by the Debye Scher-rer’s formula decreases from 11.92 to 8.54 nm when Al concentration increases from 0 to 5 wt.%. AFM images showed grains uni-formly distributed in the deposited films. An average transmittance greater than 80% was measured for the films and an en-ergy gap value of about 3.9 eV was deduced from the optical analysis. Finally, the photosensitivity properties like current-voltage characteristics, ION/IOFF ratio, growth and decay time are studied and reported. Also, we have calculated the trap depth energy using the decay portion of the rise and decay curve photocurrent.

Structural evolution-enabled BiFeO3 modulated by strontium doping with enhanced dielectric,optical and superparamagnetic properties by a modified sol-gel method

Multiferroic(BFO)nanoparticles doped with strontium with the general formula Bi1-xSrx FeO3(x=0,0.3,0.5,0.7)were synthesized using a modified sol-gel auto-combustion process.The structural,electrical,optical,and magnetic properties of the samples are discussed.The structural analysis,carried out using the x-ray powder diffraction technique,shows a structural transition from rhombohedral(R-3c)to cubic(Pm-3m)for the doping amount of strontium(Sr)equal to x=0.3.Morphological analysis of the prepared samples were carried out using scanning electron microscopy(SEM).Frequency-dependent dielectric constant and ac conductivity were studied.The doped samples,with improved dielectric properties,can be used to fabricate different optoelectronic devices.Strong dielectric dispersion and broad relaxation were exhibited by all the samples.Cole–Cole plots were employed as an effective tool to study the dispersion parameters,namely,the optical dielectric constant,static dielectric constant,relaxation time,and spreading factor.The activation energy was calculated from the relaxation peaks and Cole–Cole plots,which were found to be compatible with each other.The bandgap of the samples was calculated using diffuse reflectance spectral(DRS)analysis.Sharp and strong photoluminescence in the IR region was observed in the samples,similar to ZnO,which was reported for the first time.Room-temperature and low-temperature magnetization studies point towards the superparamagnetic nature of the samples,with an improvement in magnetic properties with doping.The antiferromagnetic behavior of bulk bismuth ferrite transforms to superparamagnetic in nature for both pure and Sr-substituted bismuth ferrite nanoparticles due to the close dimensions of crystallite size with magnetic domains leading to the break-down of the frustrated spin cycloidal moment.

Application of g-C_(3)N_(4)/sol-gel nanocomposite on AM60B magnesium alloy and investigation of its properties

To protect the AM60B magnesium alloy from corrosion,a sol-gel coating containing hydroxylated g-C_(3)N_(4)nanoplates was applied.The chemical composition of the hydroxylated g-C_(3)N_(4)nanoplates was investigated using X-ray photoelectron spectroscopy(XPS).The hydroxylation process did not affect the crystal size,specific surface area,pore volume,average pore diameter,and thermal stability of the g-C_(3)N_(4)nanoplates.After incorporating pristine and hydroxylated g-C_(3)N_(4)nanoplates,dense sol-gel coatings were obtained.Transmission electron microscopy(TEM)revealed the uniform distribution of the modified g-C_(3)N_(4)in the coating.The average roughness of the coating was also reduced after adding the modified nanoplates due to the decreased aggregation tendency.Electrochemical impedance spectroscopy(EIS)examinations in simulated acid rain revealed a significant improvement in the anticorrosion properties of the sol-gel film after the addition of the modified g-C_(3)N_(4)due to the chemical bonding of the coating to the nanoplates.

Comparative structural and electrochemical properties of mixed P2/O′3-layered sodium nickel manganese oxide prepared by sol-gel and electrospinning methods:Effect of Na-excess content

The effect of Na-excess content in the precursor on the structural and electrochemical performances of sodium nickel manganese oxide(NNMO)prepared by sol-gel and electrospinning methods is investigated in this paper.X-ray diffraction results of the prepared NNMO without adding Na-excess content indicate sodium loss,while the mixed phase of P2/O′3-type layered NNMO presented after adding Na-excess content.Compared with the sol-gel method,the secondary phase of NiO is more suppressed by using the electrospinning method,which is further confirmed by field emission scanning electron microscope images.N_(2) adsorption-desorption isotherms show no remarkably difference in specific surface areas between different preparation methods and Na-excess contents.The analysis of X-ray absorption near edge structure indicates that the oxidation states of Ni and Mn are+2 and+4,respectively.For the electrochemical properties,superior electrochemical performance is observed in the NNMO electrode with a low Na-excess content of 5wt%.The highest specific capacitance is 36.07 F·g^(-1)at0.1 A·g^(-1)in the NNMO electrode prepared by using the sol-gel method.By contrast,the NNMO electrode prepared using the electrospinning method with decreased Na-excess content shows excellent cycling stability of 100%after charge-discharge measurements for 300 cycles.Therefore,controlling the Na excess in the precursor together with the preparation method is important for improving the electrochemical performance of Na-based electrode materials in supercapacitors.

Sol-Gel法制备ZnO压敏陶瓷及其电性

采用溶胶－凝胶（ｓｏｌ－ｇｅｌ）工艺制备ＺｎＯ电压敏陶瓷粉体．探讨其制备的最佳工艺条件：以 Ｚｎ（ＮＯ３）２与 ＮａＯＨ为反应前驱物制取胶体， Ｚｎ２＋浓度控制在 ０．５ｍｏｌ·Ｌ－１以上， ｐＨ值７．５左右，预烧温度３００℃，陶瓷烧结温度１２００℃；制得的压敏电阻的非线性系数α＝２８；研究了稀土Ｌａ２Ｏ３掺杂对该陶瓷电性的影响：低浓度掺杂时，可提高压敏电压，高浓度掺杂时；不呈现压敏特性；对粉体进行了Ｘ射线衍射和透射电镜分析，预烧后得到五元掺杂的ＺｎＯ粉体粒形呈球状，属六方晶系，粒径分布窄，约为４０～８０ｎｍ．

TiO_2的微波辐射Sol-Gel法制备及其光催化性能

采用微波辐射Sol Gel法在石英砂表面制备负载型TiO2 光催化剂 ,考察不同加热方式 ,微波功率以及微波加热温度对溶胶质量的影响 ,微波加热反应制备的溶胶粒子平均粒径小于常规加热反应制备得到的溶胶粒子 ,微波加热反应适宜条件是微波功率6 0 0W ,反应温度为 90℃ .以苯酚为光催化降解研究对象 ,考察了两种方式制备的负载型TiO2 光催化剂的催化性能 ,实验结果表明微波辐射Sol Gol法制备的负载型TiO2 光催化剂光催化性能也优于常规Sol Gel法制备的负载型TiO2 光催化剂 .