Owing to different influence factors of foundation soil,the initial stress state of the soil under various working conditions is complex.To simulate this situation,in this paper,a series of tests on undisturbed soft c...Owing to different influence factors of foundation soil,the initial stress state of the soil under various working conditions is complex.To simulate this situation,in this paper,a series of tests on undisturbed soft clay under pure principal stress axis rotation were carried out by using the hollow cylinder apparatus(HCA).The influence of initial consolidation angle ζ(the angle between the vertical direction and direction of the applied load in consolidation)and intermediate principal stress coefficient b on pore water pressure accumulation of undisturbed soft clay were mainly studied.The test results show that,during pure principal stress axis rotation,the pore water pressure accumulation of the undisturbed soft clay fluctuates and increases with the rotation of the major principal stress;the values of major principal stress anglesα,corresponding to the peak value of the pore water pressure in a certain cycle,are different with different initial consolidation angles;the pore water pressure accumulation of soft clay is greatly affected by the intermediate principal stress coefficient b.With the fixed initial consolidation angle ζ,the variation trend of the maximum pore water pressure for each cycle is appropriately the same with different b values.With the increase of cycles,the difference value of pore water pressure between b=0 and b=1 in each cycle increases gradually with different initial consolidation angles ζ.While with different initial consolidation anglesζ,the increase of the pore water pressure when b increases from 0 to 0.5 is different with that when b increases from 0.5 to 1;the variation of maximum pore water pressure withζis significantly affected by the value of b;the value of maximum pore water pressure increases with the cycle number increases under all test conditions,but the growth rate decreases gradually.And the variation of maximum pore water pressure with the cycle number N is obviously influenced by both ζ and b.展开更多
Comprehensive tests on Hangzhou intact soft clay were performed, which were used to obtain the soils' critical response to undrained dynamic stress paths under different combinations of principal stress orientatio...Comprehensive tests on Hangzhou intact soft clay were performed, which were used to obtain the soils' critical response to undrained dynamic stress paths under different combinations of principal stress orientation. The different combinations included cyclic principal stress rotation (CPSR for short), cyclic shear with abrupt change of principal stress orientation (CAPSO for short) and cyclic shear with fixed principal stress orientation (CFPSO for short). On one side, under all these stress paths, samples have obvious strain inflection points and shear bands, and the excess pore water pressure is far from the level of initial effective confining pressure at failure. Stress paths of major principal stress orientation (α) alternating from negative and positive have quite different influence on soil's properties with those in which α is kept negative or positive. On the other side, due to the soil's strongly initial anisotropy, samples under double-amplitudes CPSR and CAPSO (or single-amplitude CPSR and CFPSO) have similar properties on dynamic shear strength and pore water pressure development tendency when α is kept within ±45°, while have quite different properties when α oversteps ±45°.展开更多
Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian ...Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on the saturated soft marine clay in the Yangtze Estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotropic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases （or degradation degree increases） significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared with the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does.Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.展开更多
The anisotropy effect is one of the most prominent phenomena in soil mechanics. Although many experimental programs have investigated anisotropy in sand, a computational procedure for determining anisotropy is lacking...The anisotropy effect is one of the most prominent phenomena in soil mechanics. Although many experimental programs have investigated anisotropy in sand, a computational procedure for determining anisotropy is lacking. Thus, this work aims to develop a procedure for connecting the sand friction angle and the loading orientation. All principal stress rotation tests in the literatures were processed via an artificial neural network. Then, with sensitivity analysis, the effect of intrinsic soil properties,consolidation history, and test sample characteristics on enhancing anisotropy was examined. The results imply that decreasing the grain size of the soil increases the effect of anisotropy on soil shear strength. In addition, increasing the angularity of grains increases the anisotropy effect in the sample. The stability of a sandy slope was also examined by considering the anisotropy in shear strength parameters. If the anisotropy effect is neglected, slope safety is overestimated by 5%-25%. This deviation is more apparent in flatter slopes than in steeper ones. However, the critical slip surface in the most slopes is the same in isotropic and anisotropic conditions.展开更多
The non-coaxial model simulating the non-coincidence between the principal stresses and the principal plastic strain rates is employed within the framework of finite element method（FEM） to predict the behaviors of a...The non-coaxial model simulating the non-coincidence between the principal stresses and the principal plastic strain rates is employed within the framework of finite element method（FEM） to predict the behaviors of anchors embedded in granular material.The non-coaxial model is developed based on the non-coaxial yield vertex theory,and the elastic and conventional coaxial plastic deformations are simulated by using elasto-perfectly plastic Drucker-Prager yield function according to the original yield vertex theory.Both the horizontal and vertical anchors with various embedment depths are considered.Different anchor shapes and soil friction and dilation angles are also taken into account.The predictions indicate that the use of non-coaxial models leads to softer responses,compared with those using conventional coaxial models.Besides,the predicted ultimate pulling capacities are the same for both coaxial and non-coaxial models.The non-coaxial influences increase with the increasing embedment depths,and circular anchors lead to larger non-coaxial influences than strip anchors.In view of the fact that the design of anchors is mainly determined by their displacements,ignoring the non-coaxiality in finite element numerical analysis can lead to unsafe results.展开更多
基金financially supported by the National Key Research and Development Program of China(Grant No.2019YFC1510803-2)the National Natural Science Foundation of China(Grant Nos.51639002 and 51809034)+3 种基金the China Postdoctoral Science Foundation(Grant No.2019M662533)the Open Research Fund of State Key Laboratory of Geomechanics and Geotechnical EngineeringInstitute of Rock and Soil Mechanics,Chinese Academy of Sciences(Grant No.Z017012)the Open Fund of State Key Laboratory of Coastal and Offshore Engineering,Dalian University of Technology(Grant No.LP2014)。
文摘Owing to different influence factors of foundation soil,the initial stress state of the soil under various working conditions is complex.To simulate this situation,in this paper,a series of tests on undisturbed soft clay under pure principal stress axis rotation were carried out by using the hollow cylinder apparatus(HCA).The influence of initial consolidation angle ζ(the angle between the vertical direction and direction of the applied load in consolidation)and intermediate principal stress coefficient b on pore water pressure accumulation of undisturbed soft clay were mainly studied.The test results show that,during pure principal stress axis rotation,the pore water pressure accumulation of the undisturbed soft clay fluctuates and increases with the rotation of the major principal stress;the values of major principal stress anglesα,corresponding to the peak value of the pore water pressure in a certain cycle,are different with different initial consolidation angles;the pore water pressure accumulation of soft clay is greatly affected by the intermediate principal stress coefficient b.With the fixed initial consolidation angle ζ,the variation trend of the maximum pore water pressure for each cycle is appropriately the same with different b values.With the increase of cycles,the difference value of pore water pressure between b=0 and b=1 in each cycle increases gradually with different initial consolidation angles ζ.While with different initial consolidation anglesζ,the increase of the pore water pressure when b increases from 0 to 0.5 is different with that when b increases from 0.5 to 1;the variation of maximum pore water pressure withζis significantly affected by the value of b;the value of maximum pore water pressure increases with the cycle number increases under all test conditions,but the growth rate decreases gradually.And the variation of maximum pore water pressure with the cycle number N is obviously influenced by both ζ and b.
基金Projects(50308025 50639010) supported by the National Natural Science Foundation of China
文摘Comprehensive tests on Hangzhou intact soft clay were performed, which were used to obtain the soils' critical response to undrained dynamic stress paths under different combinations of principal stress orientation. The different combinations included cyclic principal stress rotation (CPSR for short), cyclic shear with abrupt change of principal stress orientation (CAPSO for short) and cyclic shear with fixed principal stress orientation (CFPSO for short). On one side, under all these stress paths, samples have obvious strain inflection points and shear bands, and the excess pore water pressure is far from the level of initial effective confining pressure at failure. Stress paths of major principal stress orientation (α) alternating from negative and positive have quite different influence on soil's properties with those in which α is kept negative or positive. On the other side, due to the soil's strongly initial anisotropy, samples under double-amplitudes CPSR and CAPSO (or single-amplitude CPSR and CFPSO) have similar properties on dynamic shear strength and pore water pressure development tendency when α is kept within ±45°, while have quite different properties when α oversteps ±45°.
基金supported bythe National Natural Science Foundation of China(Grant Nos.50579006,50639010 and 50909014)
文摘Stiffness degradation will occur due to the generation of accumulated pore pressure in saturated soft clays under cyclic loading. The soil static-dynamic multi-purpose triaxial and torsional shear apparatus in Dalian University of Technology was employed to perform different types of test on the saturated soft marine clay in the Yangtze Estuary. Undisturbed samples of the clay were subjected to undrained cyclic vertical and torsional coupling shear and cyclic torsional shear after three-directional anisotropic consolidation with different initial consolidation parameters. Investigated were the effects of the initial orientation angle of the major principal stress, initial ratio of deviatoric stress, initial coefficient of intermediate principal stress and continuous rotation of principal stress axes on the stiffness degradation. It is found that the degradation index decreases （or degradation degree increases） significantly with increasing initial orientation angle of the major principal stress and initial ratio of deviatoric stress. Compared with the effects of the initial orientation angle of the major principal stress and initial ratio of deviatoric stress, the effect of initial coefficient of intermediate principal stress is less evident and this trend is more clearly reflected by the results of the cyclic torsional shear tests than those of the cyclic coupling shear tests. At the same cycle number, the degradation index obtained from the cyclic torsional shear test is higher than that from the cyclic coupling shear test. The main reason is that the continuous rotation in principal stress directions during cyclic coupling shear damages the original structure of the soil more than the cyclic torsional shear does.Based on a series of experiments, a mathematical model for stiffness degradation is proposed and the relevant parameters are determined.
文摘The anisotropy effect is one of the most prominent phenomena in soil mechanics. Although many experimental programs have investigated anisotropy in sand, a computational procedure for determining anisotropy is lacking. Thus, this work aims to develop a procedure for connecting the sand friction angle and the loading orientation. All principal stress rotation tests in the literatures were processed via an artificial neural network. Then, with sensitivity analysis, the effect of intrinsic soil properties,consolidation history, and test sample characteristics on enhancing anisotropy was examined. The results imply that decreasing the grain size of the soil increases the effect of anisotropy on soil shear strength. In addition, increasing the angularity of grains increases the anisotropy effect in the sample. The stability of a sandy slope was also examined by considering the anisotropy in shear strength parameters. If the anisotropy effect is neglected, slope safety is overestimated by 5%-25%. This deviation is more apparent in flatter slopes than in steeper ones. However, the critical slip surface in the most slopes is the same in isotropic and anisotropic conditions.
基金Supported by an EPSRC grant(GR/S29232/01)from the UK Government
文摘The non-coaxial model simulating the non-coincidence between the principal stresses and the principal plastic strain rates is employed within the framework of finite element method（FEM） to predict the behaviors of anchors embedded in granular material.The non-coaxial model is developed based on the non-coaxial yield vertex theory,and the elastic and conventional coaxial plastic deformations are simulated by using elasto-perfectly plastic Drucker-Prager yield function according to the original yield vertex theory.Both the horizontal and vertical anchors with various embedment depths are considered.Different anchor shapes and soil friction and dilation angles are also taken into account.The predictions indicate that the use of non-coaxial models leads to softer responses,compared with those using conventional coaxial models.Besides,the predicted ultimate pulling capacities are the same for both coaxial and non-coaxial models.The non-coaxial influences increase with the increasing embedment depths,and circular anchors lead to larger non-coaxial influences than strip anchors.In view of the fact that the design of anchors is mainly determined by their displacements,ignoring the non-coaxiality in finite element numerical analysis can lead to unsafe results.
