The thermodynamics of interactions between various oxides(CaO,MgO,Al2O3 and Y2O3) and molten Ti and Ti alloys was investigated.The dissolution mechanism of oxides in molten Ti alloys was provided and the stability o...The thermodynamics of interactions between various oxides(CaO,MgO,Al2O3 and Y2O3) and molten Ti and Ti alloys was investigated.The dissolution mechanism of oxides in molten Ti alloys was provided and the stability of oxides in molten Ti alloys was investigated and predicted by thermodynamic analysis.Interactions between oxides and Ti-Al melts were studied by oxide crucible melting experiments.By quantitative analysis,it is indicated that impurity contents in alloys are proportionally decreased with increasing the Al content in alloys and decreasing the melt temperature,which is in agreement with the results of the predicting thermodynamic stability.展开更多
Investment casting has been widely recognized as the best option in producing TiAl components with key benefits of accuracy,versatility and integrity.The collapsibility of ceramic moulds for investment casting is crit...Investment casting has been widely recognized as the best option in producing TiAl components with key benefits of accuracy,versatility and integrity.The collapsibility of ceramic moulds for investment casting is critical in the manufacturing process of TiAl components due to TiAl's intrinsic brittleness at room temperature.The aim of the present research is to provide a method for production of TiAl components by investment casting in ZrO2 ceramic moulds with improved collapsibility.Slurries prepared with high polymer additions were utilized during the preparation of ceramic moulds.The stress/strain curves obtained from green and baked ceramic moulds demonstrate that the green strength was increased with the application of high polymer,while baked strength decreased,thus the collapsibility of ceramic moulds was improved.It is suggested that this result is related to the burn-out of high polymer which left a lot of cavities.The experimental findings were also verified by the investment casting of "I"-shaped TiAl components.展开更多
A newly developed method is introduced for producing Cr 2O 3 base ceramic coating on aluminum alloys. On the basis of properly selecting base reactions, slurry is prepared and then applied onto the substrate surface...A newly developed method is introduced for producing Cr 2O 3 base ceramic coating on aluminum alloys. On the basis of properly selecting base reactions, slurry is prepared and then applied onto the substrate surface. By chemical reactions taken place in situ on the surface of aluminum alloy at relative low temperature, Cr 2O 3 base ceramic coating is formed. By means of scanning electron microscopy, the coating microstructure and the bonding mechanism are studied. X ray diffraction analysis is also used to investigate the chemical composition of the coating. The coating formation mechanism is further discussed. With a pin on disk tester, wear test is made to evaluate the wear performances of the coating. The results show that by applying the coating on aluminum alloy, the wear decreases 5 times in comparation to that without coating.展开更多
The thick and hard ceramic coatings were deposited on 2024 Al alloy by microarc oxidation in the electrolytic solution. Microstructure, phase composition and wear resistance of the oxide coatings were investigated by ...The thick and hard ceramic coatings were deposited on 2024 Al alloy by microarc oxidation in the electrolytic solution. Microstructure, phase composition and wear resistance of the oxide coatings were investigated by SEM,XRD and friction and wear tester. The microhardness and thickness of the oxide coatings were measured. The results show that the ceramic coating is mainly composed ofα-Al2O3 andγ-Al2O3. During oxidation, the temperature in the microarc discharge channel is very high to make the local coating molten. From the surface to interior of the coating, microhardness increases gradually. The microhardness of the ceramic coating is HV1800, and the microarc oxidation coatings greatly improve the antiwear properties of aluminum alloys.展开更多
The performances of mixed ceramic and sialon ceramic tools in machining nickel based alloy are tested.The negative cutting edge inclination and small tool lead angle are recommended for reducing ceramic tool failure....The performances of mixed ceramic and sialon ceramic tools in machining nickel based alloy are tested.The negative cutting edge inclination and small tool lead angle are recommended for reducing ceramic tool failure. So called“notching at depth of cut”is not actually at the depth of cutting line, but out of cutting area。 The real reason of notching is caused by shocking of “sawtooth”on sawtooth- shaped burr and fin- shaped edges of chip展开更多
The Ni-based alloy composite coatings reinforced by nanostructured Al2O3-40%TiO2 multiphase ceramic particles were prepared on the surface of 7005 aluminum alloy by plasma spray technology. The microstructure and trib...The Ni-based alloy composite coatings reinforced by nanostructured Al2O3-40%TiO2 multiphase ceramic particles were prepared on the surface of 7005 aluminum alloy by plasma spray technology. The microstructure and tribological properties of the composite coatings were researched. The results show that the composite coatings mainly consist of γ-Ni, α-Al2O3, γ-Al2O3 and rutile-TiO2 etc, and exhibit lower friction coefficients and wear losses than the Ni-based alloy coatings at different loads and speeds. The composite coating bears low contact stress at 3 N and its wear mechanism is micro-cutting wear. As loads increase to 6-12 N, the contact stress is higher than the elastic limit stress of worn surface, and the wear mechanisms change into multi-plastic deformation wear, micro-brittle fracture wear and abrasive wear. With the increase of speeds, the contact temperature of worn surface increases. The composite coating experiences multi-plastic deformation wear, fatigue wear and adhesive wear.展开更多
Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density o...Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density on microstructure and properties of the PEO coatings were studied. It was found that pore density of the coatings decreased with increasing the current density. The tribological and hardness tests suggested that the ceramic coating produced under the current density of 15 A/dm2showed the best mechanical property, which matched well with the phase analysis. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves proved that the coating obtained under 15 A/dm2 displayed the best anti-corrosion property, which was directly connected with morphologies of coatings.展开更多
Al2O3-13%TiO2 (mass fraction) coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and cer...Al2O3-13%TiO2 (mass fraction) coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating: one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.展开更多
Ceramic coatings containing ZrO2 were prepared in situ on LY12 aluminum alloy by microarc oxidation(MAO) in the mixed solution of zirconate and phosphate solution.The phase composition and morphology of the coatings...Ceramic coatings containing ZrO2 were prepared in situ on LY12 aluminum alloy by microarc oxidation(MAO) in the mixed solution of zirconate and phosphate solution.The phase composition and morphology of the coatings were studied by XRD and SEM,respectively.The growing mechanism of ceramic coatings was discussed in a preliminary manner.The results show that with an increase in MAO time,the compactness of the coating improved and the thickness increased.From the inner layer to the coating surface,the content of Zr increased,while the content of Al decreased.In addition,the coating was composed of m-ZrO2,t-ZrO2,and a little amount of γ-Al2O3.With an increase in reaction time,the relative content of t-ZrO2 within the coating sharply decreased while the relative content of m-ZrO2 sharply increased,and then both generally kept at a constant level after 60 min.展开更多
Most researches on micro-arc oxidation mainly focus on the application rather than discovering the evolution of residual stresses. However, residual stresses in the surface coatings of structural components have adver...Most researches on micro-arc oxidation mainly focus on the application rather than discovering the evolution of residual stresses. However, residual stresses in the surface coatings of structural components have adverse effects on their properties, such as fatigue life, dimensional stability and corrosion resistance, etc. The micro-arc oxidation ceramic coatings are produced on the surfaces of 6061 aluminum alloy by a homemade asymmetric AC type of micro-arc oxidation equipment of 20 kW. A constant current density of 4.4___0.1 A/dm2 and a self-regulated composite electrolyte are used. The micro-arc oxidation treatment period ranges from 10 min to 40 min, and the thickness of the ceramic coatings is more than 20 Bin. Residual stresses attributed to 7-A1203 constituent in the coatings at different micro-arc oxidation periods are analyzed by an X-ray diffractometer using the sin2~u method. The analysis results show that the residual stress in the ceramic coatings is compressive in nature, and it increases first and then decreases with micro-arc oxidation time increase. The maximum stress value is 1 667_+20 MPa for period of 20 min. Through analyzing the coating thickness, surface morphology and phase composition, it is found that the residual stress in the ceramic coatings is linked closely with the coating growth, the phase composition and the micro cracks formed. It is also found that both the heat treatment and the ultrasonic action release remarkably the residual compressive stress. The heat treatment makes the residual compressive stress value decrease 1 378 MPa. The ultrasonic action even alters the nature of the residual stress, making the residual compressive stress change into a residual tensile stress.展开更多
Ceramic coatings were prepared on Ti-6AI-4V alloy using ac micro-arc oxidation (MAO) in silicate-hypophosphate solution. Growth regularity and formation mechanism of ceramic coatings were discussed. It was found that ...Ceramic coatings were prepared on Ti-6AI-4V alloy using ac micro-arc oxidation (MAO) in silicate-hypophosphate solution. Growth regularity and formation mechanism of ceramic coatings were discussed. It was found that during the first stage the growth rate of coatings toward the external surface was larger than that toward substrate and then the coating began to grow mainly towards Ti alloy. When the total coating thickness reaches a certain value, it would no longer increase. In addition, the variations of the composition and microstructure of ceramic coatings according to the depositing time were also investigated with X-ray diffraction (XRD) and scanning electron microscope (SEM). The amount of rutile TiO2 gradually increased, whereas the amounts of the anatase TiO2 and amorphous phases first increased and then decreased slightly.展开更多
An FeMo-alloy-doped β-SiA1ON (FeMo/β-SiA1ON) composite was fabricated via a reaction-bonding method using raw materials of Si, Al2O3, A1N, FeMo, and Sm2O3. The effects of FeMo on the microstructure and mechanical ...An FeMo-alloy-doped β-SiA1ON (FeMo/β-SiA1ON) composite was fabricated via a reaction-bonding method using raw materials of Si, Al2O3, A1N, FeMo, and Sm2O3. The effects of FeMo on the microstructure and mechanical properties of the composite were investi- gated. Some properties of the composite, including its bending strength at 700℃ and after oxidization at 700℃ for 24 h in air, thermal shock resistance and corrosion resistance to molten aluminum, were also evaluated. The results show that the density, toughness, bending strength, and thermal shock resistance of the composite are obviously improved with the addition of an FeMo alloy. In addition, other properties of the composite such as its high-temperature strength and oxidized strength are also improved by the addition of FeMo alloy, and its corrosion re- sistance to molten aluminum is maintained. These findings indicate that the developed FeMo/β-SiA1ON composite exhibits strong potential for application to molten aluminum environments.展开更多
Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation (MPO). The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The p...Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation (MPO). The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The phase composition and surface morphology of the coatings were investigated by XRD and SEAM. Severe corrosion occurred on the substrate surface, while there were no obvious corrosion phenomena on the coated samples. The coatings were composed of Al2TiO5 and a little α-Al2O3 and mille TiO2, and the salt spray test did not change the composition of the coatings. The weight loss rate of the coatings decreased with increasing MPO time because of the increase in density and thickness of the coatings. The surface morphology of the coatings was influenced by salt spray corrosion test. Among the coated samples, the coating prepared for 2 h has the best corrosion resistance under salt spray test.展开更多
The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000...The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000 Hv micro-hardness. By XRD (X-ray diffractometry)and DSC (differential scanning calorimetry) analyses, the oxide layer consists of amorphous Al_2O_3,which is distinct from the results reported by the other researchers. The SEM photographs of suchlayer show that the layer is fixed tightly on the substrate alloy. So this alloy can he used in thehigh temperature and friction environment alter it is treated with such process.展开更多
ZrO2-Y2O3 ceramic coating was produced by plasma electrolytic oxidation (PEO) on ZAlSil2Cu3Ni2 alloy. The microstructure and phase composition of the coating were investigated by SEM and XRD.: The results show that...ZrO2-Y2O3 ceramic coating was produced by plasma electrolytic oxidation (PEO) on ZAlSil2Cu3Ni2 alloy. The microstructure and phase composition of the coating were investigated by SEM and XRD.: The results show that adding an appropriate amount of yttrium ion can improve the growing rate of ceramic coating at different oxidation stages and decrease arc voltage. The thickness of ZrO2-Y2O3 coating is 16 μn thicker than that of ZrO2 coating and the maximum oxidation rate improves by 0.6 μm/min. In addition, the arc voltage decreases from 227 to 172 V. It can be seen that the rate of oxidation firstly increases to some extent and then decreases with the content of yttrium ion increasing. The growth rate reaches the maximum while the content of yttrium ion is 0.05 g-L-1The maximum thickness is 90 μm.Compared to ZrO2 coating, the micropores of ZrO2-Y2O3 coating are less and the ceramic layer is repeatedly deposited by ZrO2 and Y2O3 ceramic particles. Meanwhile, the binding force between coating and substrate is better and the coating is uniform and compact. The ceramic layer is mainly composed of c-Y0.15Zr0.85O1.93□0.07, m-ZrO2, α-Al2O3, ,γ-Al2O3 and Y2O3. It is indicated that ZrO2 has beert fully stabilized by yttrium ion through the formation of solid solution.展开更多
Plasma electrolytic oxidation(PEO)has held great potential for the advancement of biodegradable implants,as it helps in developing porous bioceramic coatings on the surface of magnesium alloys.In this research work,Mg...Plasma electrolytic oxidation(PEO)has held great potential for the advancement of biodegradable implants,as it helps in developing porous bioceramic coatings on the surface of magnesium alloys.In this research work,MgO-based bioceramic coatings containing the Si,P,Ca,Na,and F elements have been successfully fabricated on an AZ31 magnesium alloy plate utilizing the PEO method.The characteristic current-voltage behavior of the samples during the process was surveyed in an electrolyte containing Ca(H_(2)PO_(4))_(2),Na_(2)SiO_(3)·9H_(2)O,Na_(3)PO_(4)·12H_(2)O,NaF,and KOH with a pH of 12.5 and electrical conductivity of 20 mS/cm^(-1).The results revealed that applying a voltage of 350-400 V(that is 50-100 V higher than the breakdown limit)could greatly facilitate the synthesis of a PEO ceramic coating with fewer defects and more uniform morphology.The resulting coating was a compositionally graded bioceramic layer with a thickness in the range of 3.5±0.4 to 6.0±0.7µm,comprising the above-mentioned elements as promising bioactive agents.The synthesized ceramic features were investigated in terms of the elemental distribution of components through the thickness,which indicated a gradual rise in the Si and P contents and,conversely,a decline in the F content towards the outer surface.The growth mechanism of the PEO coating has been discussed accordingly.展开更多
In order to join alumina ceramic to 5A05 aluminum alloy and obtain the excellent airtightness of joints whose maximum service temperature is 623 K, transient liquid phase (TLP) bonding technique was ,investigated us...In order to join alumina ceramic to 5A05 aluminum alloy and obtain the excellent airtightness of joints whose maximum service temperature is 623 K, transient liquid phase (TLP) bonding technique was ,investigated using Ag-Cu-Ti alloy as interlayer. The wetting experimental results confirm that Ti can react with alumina ceramic at 833 K by adding 2 wt.% Ti in Sn. But during bonding alumina ceramic and 5A05 aluminum alloy with Ag-Cu-Ti interlayer at 833 K, Ti preferentially reacts with Al and there is no reaction layer on alumina ceramic/Ag-Cu-Ti interface, which finally results in a poorly airtight joint.展开更多
Si/SiC ceramic composite and lnvar alloy were successfidly joined by vacuum brazing using Ti5OCu-W filler metals into which W was added to release the thermal stress of the brazed joint. Microstructures of the brazed ...Si/SiC ceramic composite and lnvar alloy were successfidly joined by vacuum brazing using Ti5OCu-W filler metals into which W was added to release the thermal stress of the brazed joint. Microstructures of the brazed joints were irwestigated by scanning electron micrascope (SEM) and energy dispersive spectrometer (EDS). The mechanical properties of the brazed joints were measured by shearing tests. The results showed that the brazed joints were composed of Ti-Cu phase, W phase and Ti-Si phase. W had no effect on the wettability and mobility of the .filler metals. The growth of Ti2 Cu phase was restrained, and the reaction between ceramic composite and filler metals was weakened. The specimen, brazed at 970°C for 5 rain, had the maximum shear strength of 108 MPa at room temperature.展开更多
To explain the growth mechanism of Al 2O 3/Al Lanxide composites,the dynamics of the directed oxidation of Al-Mg-Si alloys are analyzed.The experimental methods to produce Lanxide composites by directed oxidation of...To explain the growth mechanism of Al 2O 3/Al Lanxide composites,the dynamics of the directed oxidation of Al-Mg-Si alloys are analyzed.The experimental methods to produce Lanxide composites by directed oxidation of metal melts at high temperatures are presented.The effect of the processing factors on the microstructures and properties of Al 2O 3/Al composites and enforced Al 2O 3/Al composites is also analyzed.Compared with sintering ceramic composites,the advantages of Lanxide process and Lanxide materials are as following:it is a near net shaped process;the process is very simple;the microstructures and properties of Lanxide materials can be adjusted;and this process can be used to infiltrate ceramic fiber or particle preforms.展开更多
In-situ synthesized ceramic such as TiC,Cr7C3 and Cr5B3 reinforced Ni-based alloy composite coating was fabricated on the surface of mild steel substrate by reactive braze coating processing with colloidal graphite,Cr...In-situ synthesized ceramic such as TiC,Cr7C3 and Cr5B3 reinforced Ni-based alloy composite coating was fabricated on the surface of mild steel substrate by reactive braze coating processing with colloidal graphite,Cr,Ni,ferro-boron,Si and titanium powders as the raw materials at low temperature of 1000℃,and a new kind of coating materials was developed.By means of SEM,EDS,XRD and surface hardness tester,the microstructures,phases,hardness and wear-resistance of the coating were analyzed,respectively.The results revealed that the coating was mainly composed of the ceramic in-situ synthesized reinforcement phases of TiC,Cr7C3 and Cr5B3 and the binder phases in-situ synthesized of Ni31Si12 and(Ni,Fe)solid solution;The ceramic reinforcement phases of TiC,Cr7C3 and Cr5B3 were randomly distributed in the binder phases of Ni31Si12 and(Ni,Fe)solid solution;The coating had about 15vol%pores and can possibly be applied as a self-lubrication coating;The coating and the substrate were integrated together by metallurgical bonding;The coating had a hardness up to 91-94HR15N.展开更多
文摘The thermodynamics of interactions between various oxides(CaO,MgO,Al2O3 and Y2O3) and molten Ti and Ti alloys was investigated.The dissolution mechanism of oxides in molten Ti alloys was provided and the stability of oxides in molten Ti alloys was investigated and predicted by thermodynamic analysis.Interactions between oxides and Ti-Al melts were studied by oxide crucible melting experiments.By quantitative analysis,it is indicated that impurity contents in alloys are proportionally decreased with increasing the Al content in alloys and decreasing the melt temperature,which is in agreement with the results of the predicting thermodynamic stability.
基金supported by the National Natural Science Foundation of China under grant No. 51001040the Specialized Research Fund for the Doctoral Program of Higher Education within project No. 200802130014+1 种基金the Fundamental Research Funds for the Central Universities (grant No. HIT NSRIF.2010116)the Development program for Outstanding Young Teachers in Harbin Institute of Technology (HITQNJS 2009022)
文摘Investment casting has been widely recognized as the best option in producing TiAl components with key benefits of accuracy,versatility and integrity.The collapsibility of ceramic moulds for investment casting is critical in the manufacturing process of TiAl components due to TiAl's intrinsic brittleness at room temperature.The aim of the present research is to provide a method for production of TiAl components by investment casting in ZrO2 ceramic moulds with improved collapsibility.Slurries prepared with high polymer additions were utilized during the preparation of ceramic moulds.The stress/strain curves obtained from green and baked ceramic moulds demonstrate that the green strength was increased with the application of high polymer,while baked strength decreased,thus the collapsibility of ceramic moulds was improved.It is suggested that this result is related to the burn-out of high polymer which left a lot of cavities.The experimental findings were also verified by the investment casting of "I"-shaped TiAl components.
文摘A newly developed method is introduced for producing Cr 2O 3 base ceramic coating on aluminum alloys. On the basis of properly selecting base reactions, slurry is prepared and then applied onto the substrate surface. By chemical reactions taken place in situ on the surface of aluminum alloy at relative low temperature, Cr 2O 3 base ceramic coating is formed. By means of scanning electron microscopy, the coating microstructure and the bonding mechanism are studied. X ray diffraction analysis is also used to investigate the chemical composition of the coating. The coating formation mechanism is further discussed. With a pin on disk tester, wear test is made to evaluate the wear performances of the coating. The results show that by applying the coating on aluminum alloy, the wear decreases 5 times in comparation to that without coating.
基金Project(04-71) supported by the Scientific Research Startup Foundation of Heilongjiang Institute of Science and Technology, China
文摘The thick and hard ceramic coatings were deposited on 2024 Al alloy by microarc oxidation in the electrolytic solution. Microstructure, phase composition and wear resistance of the oxide coatings were investigated by SEM,XRD and friction and wear tester. The microhardness and thickness of the oxide coatings were measured. The results show that the ceramic coating is mainly composed ofα-Al2O3 andγ-Al2O3. During oxidation, the temperature in the microarc discharge channel is very high to make the local coating molten. From the surface to interior of the coating, microhardness increases gradually. The microhardness of the ceramic coating is HV1800, and the microarc oxidation coatings greatly improve the antiwear properties of aluminum alloys.
文摘The performances of mixed ceramic and sialon ceramic tools in machining nickel based alloy are tested.The negative cutting edge inclination and small tool lead angle are recommended for reducing ceramic tool failure. So called“notching at depth of cut”is not actually at the depth of cutting line, but out of cutting area。 The real reason of notching is caused by shocking of “sawtooth”on sawtooth- shaped burr and fin- shaped edges of chip
文摘The Ni-based alloy composite coatings reinforced by nanostructured Al2O3-40%TiO2 multiphase ceramic particles were prepared on the surface of 7005 aluminum alloy by plasma spray technology. The microstructure and tribological properties of the composite coatings were researched. The results show that the composite coatings mainly consist of γ-Ni, α-Al2O3, γ-Al2O3 and rutile-TiO2 etc, and exhibit lower friction coefficients and wear losses than the Ni-based alloy coatings at different loads and speeds. The composite coating bears low contact stress at 3 N and its wear mechanism is micro-cutting wear. As loads increase to 6-12 N, the contact stress is higher than the elastic limit stress of worn surface, and the wear mechanisms change into multi-plastic deformation wear, micro-brittle fracture wear and abrasive wear. With the increase of speeds, the contact temperature of worn surface increases. The composite coating experiences multi-plastic deformation wear, fatigue wear and adhesive wear.
基金Project(51371039)supported by the National Natural Science Foundation of China
文摘Plasma electrolytic oxidation (PEO) ceramic coatings were fabricated in a silicate-based electrolyte with the addition of potassium fluorozirconate (K2ZrF6) on 6063 aluminum alloy, and the effects of current density on microstructure and properties of the PEO coatings were studied. It was found that pore density of the coatings decreased with increasing the current density. The tribological and hardness tests suggested that the ceramic coating produced under the current density of 15 A/dm2showed the best mechanical property, which matched well with the phase analysis. Electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves proved that the coating obtained under 15 A/dm2 displayed the best anti-corrosion property, which was directly connected with morphologies of coatings.
基金Project (59975046) supported by the National Natural Science Foundation of China
文摘Al2O3-13%TiO2 (mass fraction) coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating: one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.
基金supported by the National Natural Science Foundation of China(No.50171026)Harbin Special Creation Foundation of Science and Technology for Fellow of China(No.2006RFQXG032).
文摘Ceramic coatings containing ZrO2 were prepared in situ on LY12 aluminum alloy by microarc oxidation(MAO) in the mixed solution of zirconate and phosphate solution.The phase composition and morphology of the coatings were studied by XRD and SEM,respectively.The growing mechanism of ceramic coatings was discussed in a preliminary manner.The results show that with an increase in MAO time,the compactness of the coating improved and the thickness increased.From the inner layer to the coating surface,the content of Zr increased,while the content of Al decreased.In addition,the coating was composed of m-ZrO2,t-ZrO2,and a little amount of γ-Al2O3.With an increase in reaction time,the relative content of t-ZrO2 within the coating sharply decreased while the relative content of m-ZrO2 sharply increased,and then both generally kept at a constant level after 60 min.
基金supported by National Natural Science Foundation of China(Grant No.51171167)Hebei Provincial Natural Science Foundation of China(Grant No.A2011203068)
文摘Most researches on micro-arc oxidation mainly focus on the application rather than discovering the evolution of residual stresses. However, residual stresses in the surface coatings of structural components have adverse effects on their properties, such as fatigue life, dimensional stability and corrosion resistance, etc. The micro-arc oxidation ceramic coatings are produced on the surfaces of 6061 aluminum alloy by a homemade asymmetric AC type of micro-arc oxidation equipment of 20 kW. A constant current density of 4.4___0.1 A/dm2 and a self-regulated composite electrolyte are used. The micro-arc oxidation treatment period ranges from 10 min to 40 min, and the thickness of the ceramic coatings is more than 20 Bin. Residual stresses attributed to 7-A1203 constituent in the coatings at different micro-arc oxidation periods are analyzed by an X-ray diffractometer using the sin2~u method. The analysis results show that the residual stress in the ceramic coatings is compressive in nature, and it increases first and then decreases with micro-arc oxidation time increase. The maximum stress value is 1 667_+20 MPa for period of 20 min. Through analyzing the coating thickness, surface morphology and phase composition, it is found that the residual stress in the ceramic coatings is linked closely with the coating growth, the phase composition and the micro cracks formed. It is also found that both the heat treatment and the ultrasonic action release remarkably the residual compressive stress. The heat treatment makes the residual compressive stress value decrease 1 378 MPa. The ultrasonic action even alters the nature of the residual stress, making the residual compressive stress change into a residual tensile stress.
基金This work was finicially supported by the National Natural Science Foundation of China(Grant No.50171026).
文摘Ceramic coatings were prepared on Ti-6AI-4V alloy using ac micro-arc oxidation (MAO) in silicate-hypophosphate solution. Growth regularity and formation mechanism of ceramic coatings were discussed. It was found that during the first stage the growth rate of coatings toward the external surface was larger than that toward substrate and then the coating began to grow mainly towards Ti alloy. When the total coating thickness reaches a certain value, it would no longer increase. In addition, the variations of the composition and microstructure of ceramic coatings according to the depositing time were also investigated with X-ray diffraction (XRD) and scanning electron microscope (SEM). The amount of rutile TiO2 gradually increased, whereas the amounts of the anatase TiO2 and amorphous phases first increased and then decreased slightly.
基金financially supported by the National Natural Science Foundation of China (No. 51272208)the Program for New Century Excellent Talents in University (NCET–12–0454)the Program for Young Excellent Talents in Shaanxi Province, China (2013KJXX–50)
文摘An FeMo-alloy-doped β-SiA1ON (FeMo/β-SiA1ON) composite was fabricated via a reaction-bonding method using raw materials of Si, Al2O3, A1N, FeMo, and Sm2O3. The effects of FeMo on the microstructure and mechanical properties of the composite were investi- gated. Some properties of the composite, including its bending strength at 700℃ and after oxidization at 700℃ for 24 h in air, thermal shock resistance and corrosion resistance to molten aluminum, were also evaluated. The results show that the density, toughness, bending strength, and thermal shock resistance of the composite are obviously improved with the addition of an FeMo alloy. In addition, other properties of the composite such as its high-temperature strength and oxidized strength are also improved by the addition of FeMo alloy, and its corrosion re- sistance to molten aluminum is maintained. These findings indicate that the developed FeMo/β-SiA1ON composite exhibits strong potential for application to molten aluminum environments.
基金the National Natural Science Foundation of China (No. 50171026)the Natu-ral Science Foundation of Heilongjiang Province, China (No. E2007-36).
文摘Ceramic coatings were prepared on Ti-6Al-4V alloy in NaAlO2 solution by micro-plasma oxidation (MPO). The salt spray tests of the coated samples and the substrates were carded out in a salt spray test machine. The phase composition and surface morphology of the coatings were investigated by XRD and SEAM. Severe corrosion occurred on the substrate surface, while there were no obvious corrosion phenomena on the coated samples. The coatings were composed of Al2TiO5 and a little α-Al2O3 and mille TiO2, and the salt spray test did not change the composition of the coatings. The weight loss rate of the coatings decreased with increasing MPO time because of the increase in density and thickness of the coatings. The surface morphology of the coatings was influenced by salt spray corrosion test. Among the coated samples, the coating prepared for 2 h has the best corrosion resistance under salt spray test.
基金This project is financially supported by the National Natural Science Foundation of China (No. 50071028) the Natural Science Foundation of Shandong Province (No. L2000F01)
文摘The MAO (Micro-Arc Oxidation) process is applied to a eutectic Al-Si alloy(Al-12.0 percent Si-l.0 percent Cu-0.9 percent Mg (mass fraction)). The oxide ceramic layer wasfabricated with about 220 mum thickness and 3000 Hv micro-hardness. By XRD (X-ray diffractometry)and DSC (differential scanning calorimetry) analyses, the oxide layer consists of amorphous Al_2O_3,which is distinct from the results reported by the other researchers. The SEM photographs of suchlayer show that the layer is fixed tightly on the substrate alloy. So this alloy can he used in thehigh temperature and friction environment alter it is treated with such process.
基金Funded by the National Natural Science Foundation of China(No.51401155)the School Foundation(No.XAGDXJJ1012)The Open Fund of Shaanxi Key Laboratory of Photoelectric Functional Materials and Devices(No.ZSKJ201416)
文摘ZrO2-Y2O3 ceramic coating was produced by plasma electrolytic oxidation (PEO) on ZAlSil2Cu3Ni2 alloy. The microstructure and phase composition of the coating were investigated by SEM and XRD.: The results show that adding an appropriate amount of yttrium ion can improve the growing rate of ceramic coating at different oxidation stages and decrease arc voltage. The thickness of ZrO2-Y2O3 coating is 16 μn thicker than that of ZrO2 coating and the maximum oxidation rate improves by 0.6 μm/min. In addition, the arc voltage decreases from 227 to 172 V. It can be seen that the rate of oxidation firstly increases to some extent and then decreases with the content of yttrium ion increasing. The growth rate reaches the maximum while the content of yttrium ion is 0.05 g-L-1The maximum thickness is 90 μm.Compared to ZrO2 coating, the micropores of ZrO2-Y2O3 coating are less and the ceramic layer is repeatedly deposited by ZrO2 and Y2O3 ceramic particles. Meanwhile, the binding force between coating and substrate is better and the coating is uniform and compact. The ceramic layer is mainly composed of c-Y0.15Zr0.85O1.93□0.07, m-ZrO2, α-Al2O3, ,γ-Al2O3 and Y2O3. It is indicated that ZrO2 has beert fully stabilized by yttrium ion through the formation of solid solution.
文摘Plasma electrolytic oxidation(PEO)has held great potential for the advancement of biodegradable implants,as it helps in developing porous bioceramic coatings on the surface of magnesium alloys.In this research work,MgO-based bioceramic coatings containing the Si,P,Ca,Na,and F elements have been successfully fabricated on an AZ31 magnesium alloy plate utilizing the PEO method.The characteristic current-voltage behavior of the samples during the process was surveyed in an electrolyte containing Ca(H_(2)PO_(4))_(2),Na_(2)SiO_(3)·9H_(2)O,Na_(3)PO_(4)·12H_(2)O,NaF,and KOH with a pH of 12.5 and electrical conductivity of 20 mS/cm^(-1).The results revealed that applying a voltage of 350-400 V(that is 50-100 V higher than the breakdown limit)could greatly facilitate the synthesis of a PEO ceramic coating with fewer defects and more uniform morphology.The resulting coating was a compositionally graded bioceramic layer with a thickness in the range of 3.5±0.4 to 6.0±0.7µm,comprising the above-mentioned elements as promising bioactive agents.The synthesized ceramic features were investigated in terms of the elemental distribution of components through the thickness,which indicated a gradual rise in the Si and P contents and,conversely,a decline in the F content towards the outer surface.The growth mechanism of the PEO coating has been discussed accordingly.
基金This work was supported by the National Natural Science Foundation of China ( No. 50705022).
文摘In order to join alumina ceramic to 5A05 aluminum alloy and obtain the excellent airtightness of joints whose maximum service temperature is 623 K, transient liquid phase (TLP) bonding technique was ,investigated using Ag-Cu-Ti alloy as interlayer. The wetting experimental results confirm that Ti can react with alumina ceramic at 833 K by adding 2 wt.% Ti in Sn. But during bonding alumina ceramic and 5A05 aluminum alloy with Ag-Cu-Ti interlayer at 833 K, Ti preferentially reacts with Al and there is no reaction layer on alumina ceramic/Ag-Cu-Ti interface, which finally results in a poorly airtight joint.
文摘Si/SiC ceramic composite and lnvar alloy were successfidly joined by vacuum brazing using Ti5OCu-W filler metals into which W was added to release the thermal stress of the brazed joint. Microstructures of the brazed joints were irwestigated by scanning electron micrascope (SEM) and energy dispersive spectrometer (EDS). The mechanical properties of the brazed joints were measured by shearing tests. The results showed that the brazed joints were composed of Ti-Cu phase, W phase and Ti-Si phase. W had no effect on the wettability and mobility of the .filler metals. The growth of Ti2 Cu phase was restrained, and the reaction between ceramic composite and filler metals was weakened. The specimen, brazed at 970°C for 5 rain, had the maximum shear strength of 108 MPa at room temperature.
文摘To explain the growth mechanism of Al 2O 3/Al Lanxide composites,the dynamics of the directed oxidation of Al-Mg-Si alloys are analyzed.The experimental methods to produce Lanxide composites by directed oxidation of metal melts at high temperatures are presented.The effect of the processing factors on the microstructures and properties of Al 2O 3/Al composites and enforced Al 2O 3/Al composites is also analyzed.Compared with sintering ceramic composites,the advantages of Lanxide process and Lanxide materials are as following:it is a near net shaped process;the process is very simple;the microstructures and properties of Lanxide materials can be adjusted;and this process can be used to infiltrate ceramic fiber or particle preforms.
基金supported by Yangjiang science and technology project (0202010067)Yangjiang polytechnic for providing financial assistance.
文摘In-situ synthesized ceramic such as TiC,Cr7C3 and Cr5B3 reinforced Ni-based alloy composite coating was fabricated on the surface of mild steel substrate by reactive braze coating processing with colloidal graphite,Cr,Ni,ferro-boron,Si and titanium powders as the raw materials at low temperature of 1000℃,and a new kind of coating materials was developed.By means of SEM,EDS,XRD and surface hardness tester,the microstructures,phases,hardness and wear-resistance of the coating were analyzed,respectively.The results revealed that the coating was mainly composed of the ceramic in-situ synthesized reinforcement phases of TiC,Cr7C3 and Cr5B3 and the binder phases in-situ synthesized of Ni31Si12 and(Ni,Fe)solid solution;The ceramic reinforcement phases of TiC,Cr7C3 and Cr5B3 were randomly distributed in the binder phases of Ni31Si12 and(Ni,Fe)solid solution;The coating had about 15vol%pores and can possibly be applied as a self-lubrication coating;The coating and the substrate were integrated together by metallurgical bonding;The coating had a hardness up to 91-94HR15N.