Effects of Standing Time during Pretreatment on the Nitrite Concentration Detected by Spectrophotometric Method

Food safety problems caused by excessive nitrite addition have been frequently reported and the detection of nitrite in food is particularly important. The standing time during the pretreatment of primary sample has a great influence on the concentration of nitrite tested by spectrophotometric method. In this context, three kinds of food samples are prepared, including canned mustard, canned fish and home-made pickled water. A series of standing times are placed during the sample pretreatments and the corresponding nitrite contents in these samples are detected by spectrophotometric method based on N-ethylenediamine dihydrochloride. This study aims to find out a reasonable standing time during the pretreatment of food sample, providing influence factor for precise detection of nitrite.

Catalytic spectrophotometric determination of trace selenium in microemulsion after separation and enrichment by SDG

A new catalytic spectrophotometric method was developed for the determination of trace amount of Se（Ⅳ） in microemulsion medium. The method is based on the catalytic effect of traces of Se（Ⅳ） on the oxidation of 2＇,4＇-dichlorophenylfluomne （p-CPF） by potassium bromate with HNO3 as an activator in the presence of nonionic microemulsion medium. Under optimum conditions, the calibration graph is linear in the range of 0.4-15 μg·L^-1 of Se（Ⅳ） at 480 nm. The detection limit achieved is 9.86 × 10^-10μg·L^-1. Samples were dissolved and the obtained trace Se（Ⅳ） was separated and enriched by sulphydryl dextrane gel （SDG）. The method has been applied for determination of trace selenium with satisfactory results.

A novel impedance immunosensor based on O-phenylenediamine modified gold electrode to analyze abscisic acid

An impedance immunosensor based on O-phenylenediamine modified gold electrode for the determination of phytohormone abscisic acid(ABA) was proposed.The operating pH,absorption time,absorption temperature and concentration of anti-ABA antibody were investigated to optimize the analytical performance.The calibration curve for the determination of ABA was obtained from this impedance immunosensor under optimal conditions.The results showed that the detection limit at about 1 ng/mL in the range of 10-5000 ng/mL...

Solid-phase extraction of trace Au(Ⅲ) with SDG and determination by the catalytic spectrophotometric method

The new catalytic kinetic spectrophotometric method for Au（III） determination was developed and validated. It was based on the catalytic effect of gold on the oxidation of sudan red III by ammonium peroxodisulfate （（NH4）2S2O8） with nitrilo triacetic acid as an activator in microemulsion and H2SO4 medium. Under optimum conditions, there was the linearity of the calibration curve in the concentration range from 0 to 20 μg/L Au（Ⅲ） at 520 nm. The relative standard deviation was 3.0% with a correlation coefficient of 0.9986. The detection limit achieved was 9.75 × 10^-5 μg/mL. A new method using a column packed with sulfhydryl dextrose gel （SDG） as a solid-phase extractant has been developed for the preconcentration and separation of Au（Ⅲ） ions. The method has been applied to the determination of trace gold with satisfactory results.

Spectrophotometric Determination of Fluoride in Groundwater Using Resorcin Blue Complexes

New simple and sensitive spectrophotometric determination of fluoride in drinking groundwater has been developed using aluminium-resorcin blue complex. The method is based on the reaction of fluoride with the coloured complex to produce colourless aluminium fluoride complex and releasing of the free ligand. The relationship of the reaction of flu-oride with the complex is sixth-order polynomial function. The reaction reaches equilibrium at fluoride concentration of 0.054 mM. The equilibrium constant (Keq) was calculated as 1.12 × 1014. Beer-Lambert law is obeyed in the range 0.0 - 0.024 mM of fluoride (0.0 - 1.0 mg·L-1). The molar absorptivity at 502 nm is 6.45 × 103 L·mol-1·cm-1. Fluoride concentration higher than 1.0 mg·L-1 can be measured after proper dilution. The sensitivity, detection limit, quantitation limit, and the percentage recovery of 0.75 mg·L-1 fluoride for the method were found to be 0.357 μg·ml-1., 0.07 mg·L-1, 0.2 mg·L-1, and 101.1 respectively.

A Novel Spectrophotometric Method for Determination of Gabapentin in Pharmaceutical Formulations Using 2,5-Dihydroxybenzaldehyde

A highly simple, rapid, sensitive and selective method is developed for spectrophotometric determination of gabapentin in pure form as well as in pharmaceutical formulations. The method is based on the formation of a yellow Schiff base derived from the condensation of gabapentin drug (1-amino methyl) cyclo hexane acetic acid and 2,5-dihydroxybenzaldehyde (DHBA) exhibiting a maximum absorbance at 445 nm. The composition, molar absorptivity and effect of different excipient have been determined spectrophotometrically. Under optimized experimental conditions, Beer’s law is obeyed in the concentration range 2.57 - 37.25 μg/ml. The method is validated with respect to accuracy, precision, limit of detection and limit of quantification. The Sandell sensitivity, correlation coefficient and regression equation are calculated. The equilibrium constant and free energy change using Benesi-Hildebrand plot are also determined. The Schiff base derived from condensation of gabapentin with DHBA is also synthesized and characterized. The condensation reaction mechanism has been proposed.

Application of Total Error Strategy in Validation of Affordable and Accessible UV-Visible Spectrophotometric Methods for Quality Control of Poor Medicines

In the framework of fighting against the poor quality medicines sold in developing countries using classical analytical methods easily accessible in those countries, four UV-Visible spectrophotometric methods for one antimalarial (quinine) and two antibiotics (amoxicillin and metronidazole) have been developed and validated according to the total error strategy using the accuracy profiles as a decision tool. The dosing range was 2 - 10 μg/mL (for quinine sulfate in tablet), 4 - 12 μg/mL (for quinine bichlorhydrate in oral drop-metronidazole benzaote in oral suspension) and 15 - 35 μg/mL (for amoxicillin trihydrate in capsule). The validated methods were then applied in determining the content of some analogous medicines sold in the Democratic Republic of Congo. Thus, the proposed UV-Visible spectrophotometric methods are simple and suitable to quantify quinine, amoxicillin and metronidazole in different pharmaceutical forms.

New simple spectrophotometric method for determination of the binary mixtures(atorvastatin calcium and ezetimibe;candesartan cilexetil and hydrochlorothiazide) in tablets

A new simple spectrophotometric method was developed for the determination of binary mixtures without prior separation.The method is based on the generation of ratio spectra of compound X by using a standard spectrum of compound Y as a divisor.The peak to trough amplitudes between two selected wavelengths in the ratio spectra are proportional to concentration of X without interference from Y.The method was demonstrated by determination of two drug combinations.The first consists of the two antihyperlipidemics：atorvastatin calcium（ATV） and ezetimibe（EZE）,and the second comprises the antihypertensives：candesartan cilexetil（CAN） and hydrochlorothiazide（HCT）.For mixture 1,ATV was determined using 10 μg/mL EZE as the divisor to generate the ratio spectra,and the peak to trough amplitudes between 231 and 276 nm were plotted against ATV concentration.Similarly,by using 10 μg/mL ATV as divisor,the peak to trough amplitudes between 231 and 276 nm were found proportional to EZE concentration.Calibration curves were linear in the range 2.5-40 mg/mL for both drugs.For mixture 2,divisor concentration was 7.5 μg/mL for both drugs.CAN was determined using its peak to trough amplitudes at 251 and 277 nm,while HCT was estimated using the amplitudes between 251 and 276 nm.The measured amplitudes were linearly correlated to concentration in the ranges 2.5-50 and 1-30 μg/mL for CAN and HCT,respectively.The proposed spectrophotometric method was validated and successfully applied for the assay of both drug combinations in several laboratory-prepared mixtures and commercial tablets.

A New Spectrophotometric Method for Measuring COD of Seawater

这研究为测量海水的化学需氧量(货到付款) 学习了一个新 Spectrophotometric 方法。在这个方法， COD 用一个分光光度计被测量而不是与钠 thiosulphate 滴定。测量波长被选择是三个标准葡萄糖答案的 470 nm，和 COD (货到付款 = 0.5， 1.5 和 2.5 mgL^(-1), 分别地) 并且二件海水样品(从南方黄海和 Jiaozhou 海湾) 我们分别地使用 Spectrophotometric 方法和 titrimetric 方法的 remeasured。结果证明 Spectrophotometric 方法比 titrimetric 方法有点好。Spectrophotometric 方法的相对标准差(RSD ) 是不到 2.7% ，并且海水样品的恢复从 96.3% ～ 103.8%。另外， Spectrophotometric 方法有象快速那样的另外的优点，操作简洁，分析 automatization，等等。Thereforethe Spectrophotometric 方法能被用来与令人满意的结果测量海水的 COD。

Indirect Spectrophotometric Determination of Sulphide with the Complex of Cd(Ⅱ)-5-Br-PADAP-CPB

By the use of CPB, Cd(Ⅲ) forms a highly sensitive complex with 5-Br-PADAP in aqueous solution, molar absorptivity εis 1. 21 ×105 1. mol-1. cm-1.Trace amount of sulphide can be determined from its effect on the complex of Cd (Ⅲ)-5-Br-PADAP-CPB, sulphide in the range 0~3. 2 ×10-6mol dm-3 causes a decrease in absorption, that is a linear function of the concentration, For 13ng cm-3 sulphide, common metal ions such as Na+, K+, Ca2+, Mg2+, Al3+ and anions such as CO (24μg cm-3). S2O (22μg cm-3). PO (20μg cm-3) etc. do not interfere. A method for the indirect determination of sulphide in beer and in dustrial waste water with good selectivity and accuracy is described.

Simultaneous Determination of Iron and Manganese in Water Using Artificial Neural Network Catalytic Spectrophotometric Method

A new analytical method using Back-Propagation (BP) artificial neural network and kinetic spectrophotometry for simultaneous determination of iron and magnesium in tap water, the Yellow River water and seawater is established. By conditional experiments, the optimum analytical conditions and parameters are obtained. Levenberg-Marquart (L-M) algorithm is used for calculation in BP neural network. The topological structure of three-layer BP ANN network architecture is chosen as 15-16-2 (nodes). The initial value of gradient coefficient μ is fixed at 0.001 and the increase factor and reduction factor of μ take the default values of the system. The data are processed by computers with our own programs written in MATLAB 7.0. The relative standard deviation of the calculated results for iron and manganese is 2.30% and 2.67% respectively. The results of standard addition method show that for the tap water, the recoveries of iron and manganese are in the ranges of 98.0%-104.3% and 96.5%-104.5%, and the RSD is in the range of 0.23%-0.98%; for the Yellow River water (Lijin district of Shandong Province), the recoveries of iron and manganese are in the ranges of 96.0%-101.0% and 98.7%-104.2%, and the RSD is in the range of 0.13%-2.52%; for the seawater in Qingdao offshore, the recoveries of iron and manganese are in the ranges of 95.3%-104.8% and 95.3%-104.7%, and the RSD is in the range of 0.14%-2.66%. It is found that 21 common cations and anions do not interfere with the determination of iron and manganese under the optimum experimental conditions. This method exhibits good reproducibility and high accuracy in the determination of iron and manganese and can be used for the simultaneous determination of iron and manganese in tap water and natural water. By using the established ANN- catalytic spectrophotometric method, the iron and manganese concentrations of the surface seawater at 11 sites in Qingdao offshore are determined and the level distribution maps of iron and manganese are drawn.

Azeotropic mixture used for development and validation of Lornoxicam in bulk and its tablet dosage form by spectrophotometric method

A novel,safe,economic and sensitive method of spectrophotometric estimation has been developed using Azeoptropic mixture (water∶methanol:60∶40,v/v) for the quantitative determination of Lornoxicam,a practically water-insoluble drug.Hence,Lornoxicam stock solution was prepared in Azeoptropic mixture.Lornoxicam showed maximum absorbance at 383 nm.Beer's law was obeyed in the concentration range 4-24 μg/mL with regression coefficient of 0.999.The method was validated in terms of linearity (R2=0.999),precision (CV for intra-day and inter-day was 0.28 0.68 and 0.12-0.92,respectively),accuracy (98.03-100.59％ w/w) and specificity.This method is simple,precise,accurate,sensitive and reproducible and can be used for the routine quality control testing of the marketed formulations.

Solid-liquid Extraction Spectrophotometric Determination of Copper with 2,9-dimethyl-1,10-phenanthroline

Solid liquid extraction of copper ion (I) with 2, 9-dimethyl-1, 10-phenanthroline (neo-cuproine, DMP) into molten naphthalene followed by chloroform spectrophotometric determination has been studied experimentally. The ternary complex Cu(I)-DMP-ClO4 was extracted quantitatively into molten naphthalene in the range of pH from 5 to 6 at 85 C-. Absorbance was spectrophotometrically determined at 459 nm against the reagent blank after the solid naphthalene layer was anhydrously dissolved in chloroform. Beer's law is obeyed over a concentration range of 0.5-70 mug/mL. The molar absorptivity and Sandell's sensitivity are 1.0x10(4) L/(mol(.)cm) and 0.0099 mug(.)cm(2) respectively. In addition, the various conditions on determination and the interference of coexisted ions were discussed, and the method was applied to the determination of copper ion both in tea samples and cadmium sulfate reagents. The results are in good agreement with those obtained by ICP AES method.

Study on the Spectrophotometric Determination of Rare Earths with a New Chromogenic Reagent Dibromo-p-methyl-chlorosulfonazo(DBMCSA)

A new method for the determination of cerium subgroup rare earths was studied and reported ill this paper. It was found that cerium subgroup rare earth elements react with DBMCSA in 0.6 mol/L hydrochloric acid medium to form stable blue complexes. The absorbances of equal amounts of cerium subgroup rare earths are close to each other at their maximum adsorptive wavelength (641 nm). Beer's law is obeyed for 0-20 mu g of I ars earths in 25 mi of solution. The method has been applied to the determination of the total amount of cerium subgroup rare earths in steel and cast iron samples with satisfactory results.

Spectrophotometric Simultaneous Determination of Zinc(II), Manganese(II) and Iron(II) in Pharmaceutical Preparations Using OSC-PLS

This work reports the spectrophotometric simultaneous determination of zinc（Ⅱ）, manganese（Ⅱ） and iron（Ⅱ） in pharmaceutical preparation, using orthogonal signal correctionpartial least squares （OSC-PLS）. All the factors affecting on the sensitivity were optimized and the linear dynamic range for determination of these metals was found. The PLS modeling was used for the multivariate calibration of the spectrophotometric data. The OSC was used for preprocessing of data matrices and the prediction results of model. The experimental calibration matrix was designed by measuring the absorbance over the range 450-570 nm for 21 samples of 0.05-1.05, 0.10-1.10 and 0.05-1.05μg·mL^-1 of zinc（Ⅱ）, manganese（Ⅱ） and iron（Ⅱ）, respectively. The RMSEP for zinc（Ⅱ）, manganese（Ⅱ） and iron（Ⅱ） using OSC-PLS were 0.0164, 0.0132, 0.0146, respectively. The proposed method was successfully applied the determination of zinc（Ⅱ）, manganese（Ⅱ） and iron（Ⅱ） in pharmaceutical preparations.

Rapid Estimation on the Sperm Concentration in Boar Semen by Spectrophotometric Method

[ Objective] To establish the standardized spectrophotometric method to determine boar sperm concentration. [ Method ] The relation- ships between absorbance （A）, transmittance （T） and sperm concentration （C） of different wavelengths （450, 550, 650 nm） were compared. [ Result] The maximum sperm concentration detected by absorbance presented an upward trend with the increase of the wavelengths, 202 mitliorVml （450 nm）, 224 million/ml （550 nm） and 235 mUlion/ml （650 nm）, respectively, but the stability of repeated measurement was decreased. With the increase of sperm dilution times, the stability of repeated measurement of transmittance was reduced, and when dilution times were more than 10 times （450 nm）, 6 times （550 nm） and 4 times （650 nm）, differences appeared between the observed values of repeated measurement. [ Con- clusion] Wavelength at 450 nm was found to be the most sensitive and reliable, and sperm concentration presented cubic functional regression rela- tionship or power functional regression relationship with absorbance or transmittance, respectively. The regression equation for the standard curve at 450 nm was C400 = 0.48A3 - 0.76A2 ＋ 0.67A - 0.066 （ R = 0.951 ） and C400 = 1.657T -0.108. 8 （ R = 0.940）.

Spectrophotometric Determination of Trace Chromium(VI) in Mass Chromium(III)

The method for the sepration and determination of trace Cr(VI) exiting in mass Cr(III) has been researched. The method is highly sensitive and less interference, but is simple and useful for analysis trace Cr(VI).

Quick and Simple Spectrophotometric Method of Identification of the Thermal State of Meat on the Basis of Composition and Content of Free Nucleotides

At present, there is no method for identifying meat frozen in a thermal state acceptable for production control. The role of free nucleotides in the processes of refrigeration and storage of meat, affecting the structural and mechanical properties of muscle tissue, the formation of taste and its biological value is known. In this article we compared methods for identifying the thermal state of meat based on the determination of the composition and content of free nucleotides by high-performance liquid chromatography (HPLC) and spectrophotometry [SF]. High-purity reference substances were used: free nucleotides—ATP, ADP, AMP, IMP and nucleosides-inosine and hypoxanthine. It has been experimentally established that the characteristic peaks of the absorption spectra for extracts of free nucleotides of meat frozen depended from thermal state of meat. The content of ATP is 21.8 times higher in meat frozen in a fresh state, and the amount of IMF is 12.3 times lower than in meat frozen after cooling. The results of studies of meat frozen using the HPLC method and the developed SF method show the adequacy of the data obtained by both methods. SF-method based on the determination of the optical density of the extracts of free nucleotides is recommended to justify the choice of technological process meat defrost modes.

β－CORRECTION SPECTROPHOTOMETRIC DETERMINATION OF ALUMINIUM， USING THE AL（Ⅲ）－PF－OP REACTION

Aluminium has been determined by β-correction spectrophotometer with phenylfluorone (PF)and a non-ionic surfactant, emulsifying OP in PH 8 ammoniacal buffer solution. β-correction spectrophotometric method can eliminate completely the effect of excess PF to increase the analytical sensitivity and decrease error. The results have Shown that Beer's law was obeyed over the concentration range 0-15μg Al (Ⅲ)/25ml and the relative standard deviation was less than 3.3%.

An Interaction Study of Chloro and Alkyl Substituted Benzylamine with DPPH● through UV Spectrophotometric and Physicochemical Methods at T = (298.15, 303.15 and 308.15) K

Radical scavenging activity (RSA) of chloro and methyl substituted benzylamine derivatives (BADs) has been studied using 1, 1-diphenyl-2-picrylhydrazyl free radical (DPPH?) through spectrophotometric and physico- chemical techniques at T = (298.15, 303.15 and 308.15) K. New experimental data on the density, sound velocity, isentropic and apparent molal compressibility of selected BADs + DPPH● solutions as a function of temperature and concentration are reported. The results are discussed with regards to structure-activity relationship (SAR) principles of BADs. The relative deviations in RSAs varied with structural potentials of BADs which were analyzed by making a comparative study for both the spectrophotometric and physicochemical results.