Extraction of Zr(IV) from hydrochloric acid with tri-octyl amine and Cyanex 921 in kerosene

This article reports the extraction of zirconium （IV） from aqueous HC1 solution by tri-octyl amine （TOA）, Cyanex 921, and their binary mixture using kerosene as the diluent. The effect of some parameters on the extraction of Zr（IV） was investigated such as equilibration time, aqueous phase acidity, extractant molarity, chloride ion concentration, nature of diluents, and temperature. The extraction of Zr（IV） was found to be 99% from 7.5 M HC1 using the mixture of extractants containing 0.1 M TOA and 0.02 M Cyanex 921 in kerosene. Kerosene was found to be the effective diluent for the extraction of Zr（IV） with the binary mixture of TOA and Cyanex 921. The positive enthalpy change and positive entropy change in the binary extraction system show the endothermic process with an increase in entropy. Stripping of Zr（IV） from the loaded organic phase containing the mixture of TOA （0.1 M） and Cyanex 921 （0.02 M） indicates that HNO3 and Na2CO3 are the best stripping agents.

Production of octyl levulinate biolubricant over modified H-ZSM-5:Optimization by response surface methodology

The present study highlighted the use of modified H-ZSM-5 （Meso-HZ-5） as heterogeneous catalyst for the synthesis of octyl levulinate biolubricant by catalytic esterification of biomass derived renewable levulinic acid （LA） with n-octanol. The process variables such as catalyst loading （X1）, n-octanol to LA molar ratio （X2） and reaction temperature （X3） were optimized through response surface methodology （RSM）, using Box-Behnken model. Analysis of variance was performed to determine the adequacy and significance of the quadratic model. The yield of octyl levulinate was obtained to be 99% at optimum process parameters. The developed quadratic model was found to be adequate and statistically accurate with correlation value （R2） of 0.9971 to predict the yield of octyl levulinate biolubricant. The study was also extended on the validation of theoretical and experimental data, including catalyst reusability.

Synthesis and Characterization of 2-cetyl-3-20 keto acid(N-ethyl perfluorinated octyl sulfonamide) N-ethyl ester

2-Cetyl-3-20 keto acid（N-ethyl perfluorinated octyl sulfonamide） N-ethyl ester was synthesized by the reaction of N-ethyl-N-hydroxyethyl perfluorinated octyl sulfonamide and alky ketene dimer. The experimental results show that the yield of products can be 89% when the molar ratio of perfluorinated octyl sulfonamide to ketene dimer is 1 ： 1.1 and the reaction lasts about four hours at 80 ℃. The structure of the product was characterized by FTIR and ^1HNMR. The product can dissolve in polar solvents such as NMP, DMAC, THF, DMSO, CHCl3, and 10% weight-loss temperature measured by TGA is 202℃.

Extraction Separation of Scandium，Iron and Lutetium with Isopropyl Phosphonic Acid Mono（1－hexyl－4－ethyl）OctylEster

The extraction and stripping of scandium from its sulfate solutions by isopropyl phosphonic acid mono (1-hexyl-4-ethyl) octyl ester (PT-2, HL) diluted with n-hexane are reported. A high efficiency of separation between scandium, iron and lutetium can be achieved by controlling aqueous acidity. Different mechanisms of Sc3+ with PT-2 in various acid range have been proposed.At lower aqueous acidity, it is a cation exchange reaction, while at higher acidity. a solvation reaction was ascertained. Its IR and NMR spectra have been discussed. The effect of temperature on extraction of Sc3+ was observed and thermodynamic functions were calculated.

Extraction of palladium(Ⅱ) from hydrochloride solutions with 2-n-octyl-4-isothiazolin-3-one as novel extractant

Solvent extraction of palladium （Ⅱ） from hydrochloric acid solution with 2-n-octyl-4-isothiazolin-3-one （OIT）/cyclohexane was studied. Effects of different parameters on extraction efficiency were evaluated. 99.96 % and 98.26 % palladium （Ⅱ） could be effectively extracted with 0.018 mol·L^-1 OIT/cyclohexane of 0.1 and 4.0 mol·L^-1 HCl medium, respectively. Nonpolar solvent and low acidity could improve the extracting efficiency, and successfully strip palladium （Ⅱ） from the loaded organic phase was achieved with 0.5 mol·L^-1 （NH2）2CS solution. It was proposed that the extraction of Pd com-plexes from HCl medium proceeded through the ion-association mechanism by slope method, NMR and FF-IR spectra.

2-Octyl Cyanoacrylate Skin Adhesive for Topical Skin Incision Closure in Female Pelvic Surgery

Background: 2-octyl cyanoacrylate (2OCA) high viscosity tissue adhesive (Medline Industries, Inc., Mundelein, IL) is a liquid topical skin adhesive. 2OCA offers the same design features and clinical utility in terms of flexibility, strength, and low complication rate as the commercially available 2OCA tissue adhesives. Additionally, 2OCA features high viscosity allowing for better control during the application process, polymerization without the use of an external activator, and a distinctive violet color for ease of application visualization. Objective: The aim of this prospective case series is to descriptively report clinical data with the application of 2OCA as a topical incision closure system in female pelvic surgery. The primary outcomes included: incisional pain, incisional dehiscence, and post-operative bleeding. The secondary outcome included drying times of the adhesive with regard to incision length. Methods: A prospective open-label observational case series study was conducted to evaluate the use of 2OCA in surgical wound closure of the topical skin in adult patients undergoing gynecologic surgical procedures. A total of 50 adult women undergoing gynecologic surgery were enrolled. 2OCA was applied only by surgeons who had undergone product training to the incisions in a standardized, protocol-defined fashion. Drying times for the adhesive and photography were recorded intraoperatively. Post treatment follow-up was conducted with queries of pain level, incisional dehiscence, and incisional bleeding immediately post-operatively, 48 hours, 5 - 10 days and 14 days post-treatment. Adverse events were documented. Results: 2OCA was applied to a total of 154 incisions from the 50 patients enrolled to the study. The procedures included: 16 laparoscopic total hysterectomies, 4 diagnostic laparoscopies, 2 laparoscopic myomectomies, 2 laparoscopic bilateral or unilateral salpingo-oophorectomies, 5 total robotic-assisted laparoscopic surgeries (2 total hysterectomies, 1 supracervical hysterectomy, 1 sacrocolpopexy, and one excision of endometriosis), 7 sacral neuromodulation procedures, and 18 midurethral slings. The overall rate of incisional dehiscence was 3% (4/154). The rate of reported incisional bleeding was 3% (4/154). There was 1 incisional infection. The pain reports based on a 10-point scale had a mean of 4.96 immediately post-operatively, which decreased to a mean score < 1 (0.2) by post-op day (POD) 14. The mean drying times for the various lengths of incisions included the following: 1.28 minutes for incisions ≤ 5 mm, 1.53 minutes for 6 - 8 mm, 1.66 minutes for 10 mm - 20 mm, and 1.57 minutes for the 40 - 50 mm incisions. In 23% (36/154) of incisions 2OCA was the sole method of skin closure. Conclusion: This study demonstrates that 2OCA is safe to use in gynecologic surgical incisions with low rates of post-operative incisional bleeding and incisional dehiscence. Post-operative reports of pain maintained expected levels for recovery. 2OCA is a practical alternative or augmentation to traditional suture closure of skin incisions at the time of gynecologic surgery.

Synthesis and Properties of Poly (n-Octyl Acrylate) with Uniform Polystyrene Grafts

Poly （n-octyl acrylate） with uniform polystyrene grafts （POA-g-PS） was obtained by radical copolymerization of n-octyl acrylate （OA） with PS macromer, in solution. The reactivity ratio and effects of copolymerization conditions on grafting efficiency were studied. The crude products were purified by extraction with cyclohexane and n-butanol successively. POA-g-PS exhibited a very good compatibilizing effect on the acrylic rubber/polystyrene blends. 2﹪-3﹪ of the graft copolymer was enough for enhancing the tensile strength of the blends. DSC and SEM demonstrated the enhancement of compatibility in the presence of the graft copolymer.

Extraction of Gold by Di(2-ethylhexyl)Sulfoxide and N-Octyl Sulfoxide

A long chain aliphatic sulfoxide can be used as an extractant.It can extract almost all metallic ions which can be extracted by tributylphosphate (TBP).The extraction of gold was studied by Chekushin,V. S. and Mojski,M.using petroleum sulfoxide and n-dioctyl sulfoxide(DOSO) as an extractant respectively.

Stereoselective synthesis and crystal structure of 4,6-O-benzylidene-N-octyl-D-allosamine hydrochloride

The building block of N-alkyl derivative of allosamidin（chitinase inhibitor）,4,6-O-benzylidene-N-octyl-D-allosamine hydrochloride was stereoselectively synthesized in two steps under mild conditions.Nucleophilic addition of octylamine to 2- oxoglucopyranoside gave a‘carbonyl group transfer＇ product in 62%yield.Subsequent stereoselective reduction of newly formed C=O with NaBH_4 produced title compound in 75%yield.X-ray diffraction analysis indicates the title compound adopts syn 1,2,3 stereochemistry and chair-chair conformation.The crystal structure is stabilized by hydrogen bonds.

2-Octyl-Cyanoacrylate Skin Adhesive Used as a Splinting Material in Auricular Surgery

In cases of auricular surgery, postoperative dressings are thought to be important for keeping auricular contour and in helping to prevent from dressing failures due to edema or subcutaneous hematoma, which may result in fibrous or cartilaginous proliferation. However, it is often difficult to achieve success with standard dressings because of the complicated shape of the auricle. We used 2-octyl-cyanoacrylate skin adhesive to dress the auricle after different types of auricular procedures (five cases of cryptotia, two of prominent ear, two of severe auricular laceration, two of skin grafting and one of flap repair of the partial auricle defect). The 2-octyl-cyanoacrlaate skin adhesive was applied to the suture line and the operated and peripheral areas for wider coverage. No dressing materials were placed over the surface. In all cases, the desired outcome was achieved, without subcutaneous hematoma, wound dehiscence, and wound infection. Contact dermatitis caused by the skin adhesive was not observed in any of the cases. Dressing and splinting after auricular surgery can be simply and successfully achieved using 2-octyl-cyanoacrylate skin adhesive. There is no need for more complicated dressings and post-surgical dressing changes, resulting in higher patient satisfaction.

Flotation mechanism of octylic hydroxamic acid on diaspore

Bauxite resources are widely spread in the earth. However, the effective utilization of this mineral is still under infant. The conventional collector for diaspore mineral is oleic acid. It has three main drawbacks which are highly insoluble, large dosages in bauxite flotation, and low selectivity, which hinder its application in industry. In this research, octylic hydroxamic acid was synthesized, and its collecting ability toward two major minerals in bauxite-diaspore and kaolinite was investigated. The collecting power of various reagents for diaspore are shown as follows: oleic acid<octylic hydroxamic acid; while the collecting power for kaolinite was like this: octylic hydroxamic acid<oleic acid. It is shown that octylic hydroxamic acid has the capability of high collectivity and good selectivity. The optimum pH was determined to be 8 9. Zeta potential test revealed that the anionic collectors-octylic hydroxamic acid and oleic acid had been adsorbed on the surface of diaspore and kaolinite, meanwhile the adsorption for diaspore was more remarkable. By the adsorptive capability and IR tests, the adsorption of octylic hydroxamic acid on diaspore was determined to be a process of chemical absorption, which was greater than that of oleic acid.

Long-term effects of di-octyl phthalate on the expression of immune-related genes in Tegillarca granosa

Di-octyl phthalate(DOP) is widely used as a plasticizer in the plastics industry.As a result,DOP is often found in marine water ecosystems where many species are exposed to it.Our objective was to evaluate the effect of long-term(14 d) DOP exposure(2.6,7.8,or 31.2 mg/L) on the expression of immunerelated genes in Tegillarca granosa.The expression of small heat shock protein(sHSPs) and tissue inhibitor of metalloproteinase(TIMP) were highest in clams exposed to 31.2 mg/L DOP on days 7 and 14.The relative expression of Tg-ferritin,superoxide dismutase(SOD),and metallothionein(MT) increased initially then decreased as the concentration of DOP increased.The hemoglobin of T.granosa(Tg-Hb I) exhibited two distinct expression patterns at two time points.Our results suggest that the immune response of T.granosa against DOP pollution varies depending on the dose.Additionally,we identified some immune-related genes that are promising candidates for biomarkers of DOP.

Resolving Ketoprofen Using n-Octyl-d-glucamine as an Optical Resolution Agent

The process of resolution of racemic ketoprofen using n-octyl-d-glucamine as an optical resolution agent was investigated. The process consists of preparation of the diastereomer salt of ketoprofen with n-octyl-d-glucamine, liberation of S-(+)-ketoprofen from its diastereomer salt and recovery of the remaining ketoprofen and n-octyl-d- glucamine. The suitable conditions for preparation of the diastereomer salt were methanol and ethyl acetate (1.1 by volume) as the solvent, the ratio of solvent volume to ketoprofen mass at 8ml:1g, and the molar ratio of ketoprofen to n-octyl-d-glucamine at 1:1. The preferred approach to liberate S-(+)-ketoprofen from its diastereomer salt was alkali dissolution, acid adjustment and ethyl acetate extraction. Racemization of the recovered ketoprofen could be achieved by reacting the recovered ketoprofen with 10% NaOH at 507 kPa for 6h. The recovered n-octyl-d- glucamine could be refined by acid dissolution and alkali adjustment. S-(+)-ketoprofen can be obtained with high optical purity and yield, showing that the present process is a practical and efficient one which can be used in industrial scale for preparation of S-(+)-ketoprofen.

Synthesis and Crystal Structure of Bis(nitrate)bis(N-n-octyl-α-pyrrolidone)uranyl (II)

The crystal structure of the title compound UO2(NO3)2[CH2(CH2)2CONC8H17] was determined by single-crystal X-ray diffraction. Crystal data: triclinic, space group P , a = 7.456(2), b = 8.371(2), c = 13.470(3) ? ?= 95.66(1), ?= 94.64(2), ?= 102.67(2), C24H46N4O10U, Mr = 788.68, V = 811.7(3) ?, Dc = 1.613 g/cm3, Z = 1, F(000) = 390, ?= 5.052 mm-1, the final R = 0.0256 and wR = 0.0568 for 2826 observed reflections (I > 2(I)). The central uranyl ions are coordinated by six oxygen atoms. Two of them are from the carbonyl groups of N-octyl-a-pyrrolidone molecules, and the other four from two nitrate groups.

Definition of Planarian Mortality in an Acute Toxicity Test:A Case Study on Dugesia japonica Exposed to 1-Octyl-3-methylimidazolium Bromide

In order to define the mortality criteria of planarian objectively,a case study of Dugesia japonica exposed to 1-octyl-3-methylimidazolium bromide([C8mim]Br)was performed followed by a recovery culture.The results showed that defining planarian mortality in light of its body disintegration was appropriate.If the disintegrated tissue of a planarian was more than 1/4 of its body length,it would completely degenerate.However,a planarian would regenerate the lost tissue and return to normal after a few days’recovery culture if the disintegrated part was less than 1/4 of body length.Therefore,we propose to use body disintegration as the endpoint of planarian mortality,i.e.,1/4 body length degenerated is the critical threshold of mortality and survival of planarians when exposed to toxicants.This criterion could be adapted in the standardization of testing protocols and comparability of acute toxicity test or other toxicological research using planarian as the test animal.

Study on Modification of Octyl-α-Cyanoacrylate Medical Adhesive

Objective:In order that the adhesive character could be improved to modify the octyl-α-cyanoacrylate(OCA) medical adhesive.Methods:Suitable modifiers involving polycaprolactone(PCL),dibutyl phthalate (DBP),dioctyl phthalate(DOP) and poly octyl methacrylat(POMA) have been chosen to modify the OCA adhesive,then tensile shear strength and adhesive strength are tested to evaluate the bond character of adhesives.Results:The PCL group's tensile shear strength and adhesive strength in normal temperature are descended while the other groups'are all enhanced.Conclusion:The modification of properties of the other groups is effectively promoted in the aspect of the bond character,except the PCL group treated in normal temperature and the PCL modified group treated by rectification get a best improvement in the agglutinate intention, while the stability is expected to be improved.

Action mechanism of octylic hydroxamic acid on diaspore

The conventional collector for diaspore mineral is oleic acid,which is highly insoluble and must be used in high dosage in bauxite flotation,that is the great drawback of oleic acid in use.Octylic hydroxamic acid was synthesized,and its collecting ability to certain minerals in bauxite:diaspore and kaolinite were studied.The collecting power of various reagents to diaspore in an incremental sequence was shown as follows:oleic acid<octylic hydroxamic acid,while the incremental sequence of the collecting power to kaolinite was like this:octylic hydroxamic acid < oleic acid.It could be seen that octylic hydroxamic acid had the capability of high collectivity and good selectivity,and octylic hydroxamic acid was chosen to use in the following experiments.Reduced zeta potential showed the adsorption of the anionic collector on the mineral.By the adsorptive capability and IR(infrared ray)tests,the adsorption of octylic hydroxamic acid on diaspore was determined to be chemical absorption,which was greater than that of oleic acid,as it was absorption by hydrogen bond.

人参皂苷辛酸酯通过内质网应激诱导肝癌细胞免疫原性细胞死亡的机制研究

目的:探讨人参皂苷辛酸酯(Rh2-O)能否诱导Huh-7肝癌细胞免疫原性细胞死亡及可能机制。方法:体外培养Huh-7细胞,设置空白对照组、Rh2-O药物组及阳性对照组(米托蒽醌处理),CCK-8、流式细胞术分别检测细胞活力和凋亡,ELISA及化学发光法分别检测细胞上清高迁移率族蛋白1(HMGB1)和三磷酸腺苷(ATP)含量,免疫荧光法检测细胞钙网蛋白(CRT)的膜外翻,荧光探针DCFH-DA检测细胞内ROS水平,Western blot检测细胞内质网应激信号通路相关蛋白表达。结果:Rh2-O可显著降低细胞活力,促进细胞凋亡,诱导细胞HMGB1分泌、ATP释放及CRT膜外翻,使细胞内蓄积大量ROS,提高内质网应激信号通路相关蛋白PERK、eIF2α、p-eIF2α表达(均P<0.05)。内质网应激抑制剂4-苯基丁酸(4-PBA)预处理可显著减弱Rh2-O诱导的CRT膜外翻(P<0.05)。结论:Rh2-O可诱导肝癌细胞发生免疫原性细胞死亡,其机制可能与Rh2-O激活内质网应激促进细胞CRT膜外翻有关。

Synthesis, Thermal Degradation and Dielectric Properties of Poly[octyl(triphenylethynyl)]silane Resin

Octyl(triphenylethynyl)silane monomer(OTPES)was synthesized with ethyl bromide,octyltrichlorosilane and phenylethylene by Grignard reaction.The molecular structure was confirmed by FTIR and NMR.The poly[octyl(triphenylethynyl)]silane resin(POTPES)was prepared by thermal polymerization and the corresponding thermal degradation behavior wasstudied by thermogravimetric analysis(TG)combining with model and model-free fitted methods.The dielectric property of resin was also studied by vector network analyzer.The results show that the melt point of OTPES was 50℃ and the processing window was over 236℃.The resin degradation temperature of Td5 occurred over 433℃ and the char yield was over 60%at 800℃.Based on Kissinger,Flynn-Wall-Ozawa,Coats-Redfern,Achar,Vyazovkin-Wight and Tang methods,the reaction activity(E)was 155.51,152.97,150.82,146.02,148.38 and 148.77 kJ/mol,respectively.Dielectric properties analysis displayed that the real part(ε′)and the imaginary part(ε″)of the relative complex permittivity of POTPES was 2.5 and 0.05,respectively,and the dielectric loss tangent was between 0.03 and 0.25.The reflection loss of resin was more than?2.85 dB in all range of 1–5 mm thicknesses and 2–18 GHz frequency,which indicated that POTPES resin was a real wave-transparent resin matrix.

凝胶渗透色谱法测定辛基酚醛增粘树脂相对分子质量及其分布

采用凝胶渗透色谱(GPC)法测定辛基酚醛增粘树脂相对分子质量及其分布,并研究辛基酚醛增粘树脂相对分子质量对其软化点和增粘效果的影响。确定的测试条件为:流速1.0 mL·min^(-1),柱温40℃,试样溶液质量浓度(2±0.2) mg·mL^(-1);辛基酚醛增粘树脂的软化点和增粘效果随着其相对分子质量的增大而提高。