Remaining oil distribution characteristics in an oil reservoir with ultra-high water-cut

An accurate mapping and understanding of remaining oil distribution is very important for water control and stabilize oil production of mature oilfields in ultra-high water-cut stage.Currently,the Tuo-21 Fault Block of the Shengtuo Oilfield has entered the stage of ultra-high water cut(97.2%).Poor adaptability of the well pattern,ineffective water injection cycle and low efficiency of engineering measures(such as workover,re-perforation and utilization of high-capacity pumps)are the significant problems in the ultra-high water-cut reservoir.In order to accurately describe the oil and water flow characteristics,relative permeability curves at high water injection multiple(injected pore volume)and a semiquantitative method is applied to perform fine reservoir simulation of the Sand group 3e7 in the Block.An accurate reservoir model is built and history matching is performed.The distribution characteristics of remaining oil in lateral and vertical directions are quantitatively simulated and analyzed.The results show that the numerical simulation considering relative permeability at high injection multiple can reflect truly the remaining oil distribution characteristics after water flooding in an ultrahigh water-cut stage.The distribution of remaining oil saturation can be mapped more accurately and quantitatively by using the‘four-points and five-types’classification method,providing a basis for potential tapping of various remaining oil types of oil reservoirs in late-stage of development with high water-cut.

Reclassification and distribution patterns of discovered oils in theDongying Depression, Bohai Bay Basin, China

The Dongying Depression is an important petrolifeous province,with diverse source rocks and complex petroleum distribution patterns.A total of 32 crude oils were analyzed by the gas chromatographyemass spectrometry and isotopic compositions to better understanding the petroleum systems in the study area.Three oil types were classified by hierarchical cluster analyses.Type I and II oils have closely correlation with the discovered source rocks,which have been confirmed to be mainly derived from the lower third and upper forth member of the Eocene Shahejie Formation source rocks(Es3^(L) and Es4^(U)),respectively.Obviously,type III oils contain abundant gammacerane,tricyclic terpanes and C_(29) steranes and have lower values of δ13C than type I and II oils,indicating a completely different source rock and biological origins.Until recently,type III oils fail to match any of the discovered source rock,which contains main contribution of aquatic organism or/and bacteria inputs.In addition,the spacial distribution of these three oil types were discussed.Type I oils mainly distributed in the Es3 and Es4 reservoirs that closed to the generative kitchens.Type II oils occurred in the Es4 reservoirs in the sourthern slope of the depression,which probably caused by lateral migration along the horizontal fractures and sandstone layers within the Es4 interval.Differently,type III oils in the sourthern slope of the depression were mainly discovered in the Eocene Kongdian or Ordocician reservoirs,which suggests great exploration potential of deep underlying strata.

Gulong shale oil enrichment mechanism and orderly distribution of conventional–unconventional oils in the Cretaceous Qingshankou Formation,Songliao Basin,NE China

Through the study of organic matter enrichment,hydrocarbon generation and accumulation process of black shale of the Cretaceous Qingshankou Formation in the Songliao Basin,the enrichment mechanism of Gulong shale oil and the distribution of conventional–unconventional oil are revealed.The Songliao Basin is a huge interior lake basin formed in the Early Cretaceous under the control of the subduction and retreat of the western Pacific plate and the massive horizontal displacement of the Tanlu Fault Zone in Northeast China.During the deposition of the Qingshankou Formation,strong terrestrial hydrological cycle led to the lake level rise of the ancient Songliao Basin and the input of a large amount of nutrients,resulting in planktonic bacteria and algae flourish.Intermittent seawater intrusion events promoted the formation of salinization stratification and anoxic environment in the lake,which were beneficial to the enrichment of organic matters.Biomarkers analysis confirms that the biogenic organic matter of planktonic bacteria and algae modified by microorganisms plays an important role in the formation of high-quality source rocks with high oil generation capability.There are four favorable conditions for the enrichment of light shale oil in the Qingshankou Formation of the Gulong Sag,Songliao Basin:the moderate organic matter abundance and high oil potential provide sufficient material basis for oil enrichment;high degree of thermal evolution makes shale oil have high GOR and good mobility;low hydrocarbon expulsion efficiency leads to a high content of retained hydrocarbons in the source rock;and the confinement effect of intra-layer cement in the high maturity stage induces the efficient accumulation of light shale oil.The restoration of hydrocarbon accumulation process suggests that liquid hydrocarbons generated in the early(low–medium maturity)stage of the Qingshankou Formation source rocks accumulated in placanticline and slope after long-distance secondary migration,forming high-quality conventional and tight oil reservoirs.Light oil generated in the late(medium–high maturity)stage accumulated in situ,forming about 15 billion tons of Gulong shale oil resources,which finally enabled the orderly distribution of conventional–unconventional oils that are contiguous horizontally and superposed vertically within the basin,showing a complete pattern of“whole petroleum system”with conventional oil,tight oil and shale oil in sequence.

The effect of interbeds on distribution of i ncremental oil displaced by a polymer flood

This paper discusses the effect of influencing factors on the distribution of incremental oil displaced by a polymer flood （extra-displaced oil） using numerical reservoir simulation. These factors include the location, area and permeability of a thin low-permeability interbed, and the perforation location relative to the interbed. Simulation results show the locations from where the incremental oil was displaced by the polymer solution. The interbed position from the oil formation top affects the location of extra-displaced oil. The interbed area has a slight influence on the whole shape of extra-displaced oil. Larger interbed area leads to higher partition extent of extra-displaced oil. Higher vertical permeability of interbeds contributes to worse partition extent of extra-displaced oil and the partition effect disappears if the ratio of vertical to horizontal permeability is more than 0.05. The perforation location relative to the interbed affects polymer displacement efficiency, and also has a significant effect on the distribution of extra-displaced oil in polymer flooding.

Formation and distribution characteristics of Proterozoic–Lower Paleozoic marine giant oil and gas fields worldwide

There are rich oil and gas resources in marine carbonate strata worldwide.Although most of the oil and gas reserves discovered so far are mainly distributed in Mesozoic,Cenozoic,and upper Paleozoic strata,oil and gas exploration in the Proterozoic–Lower Paleozoic（PLP）strata—the oldest marine strata—has been very limited.To more clearly understand the oil and gas formation conditions and distributions in the PLP marine carbonate strata,we analyzed and characterized the petroleum geological conditions,oil and gas reservoir types,and their distributions in thirteen giant oil and gas fields worldwide.This study reveals the main factors controlling their formation and distribution.Our analyses show that the source rocks for these giant oil and gas fields are mainly shale with a great abundance of type I–II organic matter and a high thermal evolution extent.The reservoirs are mainly gas reservoirs,and the reservoir rocks are dominated by dolomite.The reservoir types are mainly karst and reef–shoal bodies with well-developed dissolved pores and cavities,intercrystalline pores,and fractures.These reservoirs arehighly heterogeneous.The burial depth of the reservoirs is highly variable and somewhat negatively correlated to the porosity.The cap rocks are mainly thick evaporites and shales,with the thickness of the cap rocks positively correlated to the oil and gas reserves.The development of high-quality evaporite cap rock is highly favorable for oil and gas preservation.We identified four hydrocarbon generation models,and that the major source rocks have undergone a long period of burial and thermal evolution and are characterized by early and long periods of hydrocarbon generation.These giant oil and gas fields have diverse types of reservoirs and are mainly distributed in paleo-uplifts,slope zones,and platform margin reef-shoal bodies.The main factors that control their formation and distribution were identified,enabling the prediction of new favorable areas for oil and gas exploration.

An experimental study on oil droplet size distribution in subsurface oil releases

Oil droplet size distribution （ODSD） plays a critical role in the rising velocity and transport of oil droplets in subsurface oil releases. In this paper, subsurface oil release experiments were conducted to study ODSD under different experimental conditions in a laboratory water tank observed by two high-speed cameras in March and April 2017. The correlation formulas Oh=lO.2Re-~ and Oh=39.2Re-1 （Re represents Reynolds number and Oh represents Ohnesorge number） were established to distinguish the boundaries of the three instability regimes in dimensionless space based on the experimental results. The oil droplet sizes from the experimental data showed an excellent match to the Rosin-Rammler distribution function with determination coefficients ranging from 0.86 to 1.00 for Lvda 10-1 oil. This paper also explored the influence factors on and change rules ofoil droplet size. The volume median diameter d50 decreased steadily with increasing jet velocity, and a sharp decrease occurred in the laminar-breakup regime. At Weber numbers （We） 〈100, the orifice diameter and oil viscosity appeared to have a large influence on the mean droplet diameter. At 100〈We〈1 000, the oil viscosity appeared to have a larger influence on the relative mean droplet diameter.

The gradual subduction-collision evolution model of Proto-South China Sea and its control on oil and gas

This study involved outcrop,drilling,seismic,gravity,and magnetic data to systematically document the geological records of the subduction process of Proto-South China Sea(PSCS)and establish its evolution model.The results indicate that a series of arc-shaped ophiolite belts and calcalkaline magmatic rocks are developed in northern Borneo,both of which have the characteristics of gradually changing younger from west to east,and are direct signs of subduction and collision of PSCS.At the same time,the subduction of PSCS led to the formation of three accretion zones from the south to the north in Borneo,the Kuching belt,Sibu belt,and Miri belt.The sedimentary formation of northern Borneo is characterized by a three-layer structure,with the oceanic basement at the bottom,overlying the deep-sea flysch deposits of the Rajang–Crocker group,and the molasse sedimentary sequence that is dominated by river-delta and shallow marine facies at the top,recording the whole subduction–collision–orogeny process of PSCS.Further,seismic reflection and tomography also confirmed the subduction and collision of PSCS.Based on the geological records of the subduction and collision of PSCS,combined with the comprehensive analysis of segmented expansion and key tectonic events in the South China Sea,we establish the“gradual”subduction-collision evolution model of PSCS.During the late Eocene to middle Miocene,the Zengmu,Nansha,and Liyue–Palawan blocks were separated by West Baram Line and Balabac Fault,which collided with the Borneo block and Kagayan Ridge successively from the west to the east,forming several foreland basin systems,and PSCS subducted and closed from the west to the east.The subduction and extinction of PSCS controlled the oil and gas distribution pattern of southern South China Sea(SSCS)mainly in three aspects.First,the“gradual”closure process of PSCS led to the continuous development of many large deltas in SSCS.Second,the deltas formed during the subduction–collision of PSCS controlled the development of source rocks in the basins of SSCS.Macroscopically,the distribution and scale of deltas controlled the distribution and scale of source rocks,forming two types of source rocks,namely,coal measures and terrestrial marine facies.Microscopically,the difference of terrestrial higher plants carried by the delta controlled the proportion of macerals of source rocks.Third,the difference of source rocks mainly controlled the distribution pattern of oil and gas in SSCS.Meanwhile,the difference in the scale of source rocks mainly controlled the difference in the amount of oil and gas discoveries,resulting in a huge amount of oil and gas discoveries in the basin of SSCS.Meanwhile,the difference of macerals of source rocks mainly controlled the difference of oil and gas generation,forming the oil and gas distribution pattern of“nearshore oil and far-shore gas”.

A hindcast of the Bohai Bay oil spill during June to August 2011

An operational three-dimensional oil spill model is developed by the National Marine Environmental Forecasting Center（NMEFC）, State Oceanic Administration, China, and the model has been running for 9 a. On June 4 and 17,2011, oil is spilled into the sea water from two separate oil platforms in the Bohai Bay, i.e., Platforms B and C of Penglai 19-3 oilfield. The spill causes pollution of thousands of square kilometres of sea area. The NMEFC’s oil spill model is employed to study the Penglai 19-3 oil-spill pollution during June to August 2011. The wind final analysis data of the NMEFC, which is based on a weather research and forecasting（WRF） model, are analyzed and corrected by comparing with the observation data. A corrected current filed is obtained by forcing the princeton ocean model（POM） with the corrected wind field. With the above marine environmental field forcing the oil spill model, the oil mass balance and oil distribution can be produced. The simulation is validated against the observation, and it is concluded that the oil spill model of the NMEFC is able to commendably simulate the oil spill distribution. Thus the NMEFC’s oil spill model can provide a tool in an environmental impact assessment after the event.

Experimental study on the oil production characteristics during the waterflooding of different types of reservoirs in Ordos Basin, NW China

Waterflooding experiments were conducted in micro-models(microscopic scale)and on plunger cores from low permeability,extra-low permeability and ultra-low permeability reservoirs in the Ordos Basin under different displacement pressures using the NMR techniques to find out pore-scale oil occurrence state,oil production characteristics and residual oil distribution during the process of waterflooding and analyze the effect of pore structure and displacement pressure on waterflooding efficiency.Under bound water condition,crude oil mainly occurs in medium and large pores in the low-permeability sample,while small pores and medium pores are the main distribution space of crude oil in extra-low permeability and ultra-low permeability samples.During the waterflooding,crude oil in the medium and large pores of the three types of samples are preferentially produced.With the decrease of permeability of the samples,the waterflooding front sequentially shows uniform displacement,network displacement and finger displacement,and correspondingly the oil recovery factors decrease successively.After waterflooding,the residual oil in low-permeability samples is mainly distributed in medium pores,and appears in membranous and angular dispersed phase;but that in the extra-low and ultra-low permeability samples is mainly distributed in small pores,and appears in continuous phase formed by a bypass flow and dispersed phase.The low-permeability samples have higher and stable oil displacement efficiency,while the oil displacement efficiency of the extra-low permeability and ultra-low permeability samples is lower,but increases to a certain extent with the increase of displacement pressure.

The mechanism of hydraulic fracturing assisted oil displacement to enhance oil recovery in low and medium permeability reservoirs

Aiming at the technology of hydraulic fracturing assisted oil displacement which combines hydraulic fracturing,seepage and oil displacement,an experimental system of energy storage and flowback in fracturing assisted oil displacement process has been developed and used to simulate the mechanism of percolation,energy storage,oil displacement and flowback of chemical agents in the whole process.The research shows that in hydraulic fracturing assisted oil displacement,the chemical agent could be directly pushed to the deeper area of the low and medium permeability reservoirs,avoiding the viscosity loss and adhesion retention of chemical agents near the pay zone;in addition,this technology could effectively enlarge the swept volume,improve the oil displacement efficiency,replenish formation energy,gather and exploit the scattered residual oil.For the reservoir with higher permeability,this measure takes effect fast,so to lower cost,and the high pressure hydraulic fracturing assisted oil displacement could be adopted directly.For the reservoir with lower permeability which is difficult to absorb water,hydraulic fracturing assisted oil displacement with surfactant should be adopted to reduce flow resistance of the reservoir and improve the water absorption capacity and development effect of the reservoir.The degree of formation energy deficit was the main factor affecting the effective swept range of chemical agents.Moreover,the larger the formation energy deficit was,the further the seepage distance of chemical agents was,accordingly,the larger the effective swept volume was,and the greater the increase of oil recovery was.Formation energy enhancement was the most important contribution to enhanced oil recovery(EOR),which was the key to EOR by the technology of hydraulic fracturing assisted oil displacement.

Paleozoic Composite Petroleum System of North Africa:Hydrocarbon Distribution and Main Controlling Factors

North Africa, which is one of the main oil and gas producing regions in the world, is best known for its subsalt Paleozoic-Triassic reservoirs and Paleozoic source rocks. Hydrocarbon abundance varies greatly from one structural domain to another areally and from one stratigraphic interval to another vertically. Analyses of the essential elements and geological processes of the Paleozoic petroleum system indicate that the distribution of the Lower Silurian shale source rocks, the development of a thick Mesozoic overburden, the presence of the Upper Triassic-Lower Jurassic evaporite seal are the most important factors goveming the distribution of the Paleozoic-sourced hydrocarbons in North Africa. The Mesozoic sequence plays a critical role for hydrocarbons to accumulate by enabling the maturation of the Paleozoic source rocks during the Mesozoic-Paleogene times and preserving the accumulated hydrocarbons. Basins and surrounding uplifts, particularly the latter, with a thick Mesozoic sequence and a regional evaporite seal generally have abundant hydrocarbons. Basins where only a thin Mesozoic overburden was developed tend to have a very poor to moderate hydrocarbon prospectivity.

Restoration of Eroded Thickness of the Neogene Strata in the Western Qaidam Basin and Its Significance for Oil and Gas Occurrence

During the Pleistocene, the western Qaidam Basin has largely experienced strong structural reconstruction and strong erosion. First, the eroded thickness of Neogene strata was restored approximately by the stratigraphic profile comparison method and plane trend surface restoring method; then, accurate calculation of erosion was recovered using vitrinite reflectance, and the erosion that was restored by the trend surface restoring method was corrected; finally, a distribution map of cumulative erosion was produced. This study marks an important achievement in that one of the most important parameters of basin tectonic evolution, sedimentary evolution, and oil and gas accumulation history has been obtained, and that a basic geological problem has been solved in the Qaidam Basin. The areas with high erosion and low erosion are shown in the map and a close relation between the distribution of oil and gas fields and erosion was recognized. Large and medium oil and gas fields are mainly distributed in areas with medium and low erosion. It is difficult to form large-scale oil and gas accumulation in areas in which erosion is more than 2000 m. The mechanism of the relation between oil and gas distribution and erosion is explained. This study will be of use in predicting the distribution of oil and gas.

Influence of the cage on the migration and distribution of lubricating oil inside a ball bearing

The migration and distribution of lubricant oil in a rolling bearing strongly affect the elastohydrodynamic lubrication performance between the balls and rings.However,oil re-lubrication is highly dependent on the bearing design,which is different from the ball-on-disc model.This study directly observed the distribution of the lubricant film in a custom-made model-bearing rig,with an outer ring replaced by a glass ring to allow full optical access.The influence of the cage type and surface properties were presented.The physical origin of the re-lubrication mechanism,including capillary flow and mechanical redistribution,was discussed.

Differential structure of Ordovician karst zone and hydrocarbon enrichment in paleogeomorphic units in Tahe area,Tarim Basin,NW China

Based on a large number of drilling,logging,seismic and production data,the differential structures of karst zone and hydrocarbon distribution in different paleogeomorphic units of the Tahe area,Tarim Basin,are discussed by analyzing the karst drainages and flowing channels.The karst paleogeomorphy of Ordovician in Tahe area is composed of watershed,karst valley and karst basin.The watershed has epikarst zone of 57.8 m thick on average and vadose karst zone of 115.2 m thick on average with dense faults,fractures and medium-small fracture-caves,and 76.5%of wells in this area have cumulative production of more than 5×10^(4) t per well.The karst valleys have epikarst zone,vadose karst zone and runoff karst zone,with an average thickness of 14.6,26.4 and 132.6 m respectively.In the runoff karst zone,the caves of subsurface river are mostly filled by fine sediment,with a filling rate up to 86.8%,and 84.9%of wells in this area have cumulative production of less than 2×10^(4) t per well.The karst basin has no karst zone,but only fault-karst reservoirs in local fault zones,which are up to 600 m thick and closely developed within 1 km around faults.Different karst landforms have different water flowing pattern,forming different karst zone structures and resulting in differential distribution of oil and gas.The watershed has been on the direction of oil and gas migration,so medium-small sized connected fracture-caves in this area have high filling degree of oil and gas,and most wells in this area have high production.Most caves in subsurface river are filled due to strong sedimentation and transportation of the river,so the subsurface river sediment has low hydrocarbon abundance and more low production oil wells.The faults linking source rock are not only the water channels but also the oil-gas migration pathways,where the karst fractures and caves provide huge reservoir space for oil and gas accumulation.

Differences and controlling factors of composite hydrocarbon accumulations in the Tazhong uplift, Tarim Basin, NW China

Based on three-dimensional seismic interpretation, structural and sedimentary feature analysis, and examination of fluid properties and production dynamics, the regularity and main controlling factors of hydrocarbon accumulation in the Tazhong uplift, Tarim Basin are investigated. The results show that the oil and gas in the Tazhong uplift has the characteristics of complex accumulation mainly controlled by faults, and more than 80% of the oil and gas reserves are enriched along fault zones. There are large thrust and strike-slip faults in the Tazhong uplift, and the coupling relationship between the formation and evolution of the faults and accumulation determine the difference in complex oil and gas accumulations. The active scale and stage of faults determine the fullness of the traps and the balance of the phase, that is, the blocking of the transport system, the insufficient filling of oil and gas, and the unsteady state of fluid accumulation are dependent on the faults. The multi-period tectonic sedimentary evolution controls the differences of trap conditions in the fault zones, and the multi-phase hydrocarbon migration and accumulation causes the differences of fluid distribution in the fault zones. The theory of differential oil and gas accumulation controlled by fault is the key to the overall evaluation, three-dimensional development and discovery of new reserves in the Tazhong uplift.