期刊文献+
共找到2,162篇文章
< 1 2 109 >
每页显示 20 50 100
Organic matter transformation ratio, hydrocarbon expulsion efficiency and shale oil enrichment type in Chang 7_(3) shale of Upper Triassic Yanchang Formation in Ordos Basin, NW China 被引量:1
1
作者 ZHAO Wenzhi BIAN Congsheng +4 位作者 LI Yongxin LIU Wei DONG Jin WANG Kun ZENG Xu 《Petroleum Exploration and Development》 2023年第1期14-26,共13页
The major enrichment type of shale oil in the Chang 7_(3) shale of Upper Triassic Yanchang Formation in the Ordos Basin is unknown.This paper analyzes the organic matter transformation ratio,hydrocarbon expulsion effi... The major enrichment type of shale oil in the Chang 7_(3) shale of Upper Triassic Yanchang Formation in the Ordos Basin is unknown.This paper analyzes the organic matter transformation ratio,hydrocarbon expulsion efficiency and roof/floor sealing conditions of the Chang 7_(3) shale,and evaluates the major enrichment type of shale oil in this interval.The average organic matter transformation ratio of the Chang 7_(3) shale is about 45%;in other words,more than 50%of the organic matters have not transformed to hydrocarbons,and the lower the maturity,the greater the proportion of untransformed organic matters.The cumulative hydrocarbon expulsion efficiency of the transformed hydrocarbon is 27.5% on average,and the total proportion of untransformed organic matters plus retained hydrocarbons is greater than 70%.The relative hydrocarbon expulsion efficiency of the Chang 7_(3) shale is 60%on average,that is,about 40% of hydrocarbons retain in the shale.The Chang 7_(3) shale corresponds to Chang 7_(1+2) and Chang 8 sandstones as the roof and floor,respectively,and is further overlaid by Chang 6 shale,where extensive low porosity and low permeability–tight oil reservoirs have formed in the parts with relatively good porosity and permeability.Moreover,the Chang 7_(3) shale is tested to be in a negative pressure system(the pressure coefficient of 0.80–0.85).Therefore,the roof/floor sealing conditions of the Chang 7_(3) shale are poor.The retained hydrocarbons appear mostly in absorbed status,with low mobility.It is concluded that the medium–high mature shale oil is not the major enrichment type of shale oil in the Chang 7_(3) shale,but there may be enrichment opportunity for shale oil with good mobility in the areas where the sealing conditions are good without faults and fractures and oil reservoirs are formed off Chang 7_(1+2),Chang 6 and Chang 8.Furthermore,low–medium mature shale oil is believed to have great potential and is the major enrichment type of shale oil in the Chang 7_(3) shale.It is recommended to prepare relevant in-situ conversion technologies by pilot test and figure out the resource availability and distribution. 展开更多
关键词 organic matter transformation ratio hydrocarbon expulsion efficiency sealing condition continental shale oil major enrichment type Chang 7_(3)shale Triassic Ordos Basin
下载PDF
Effects of Temperature and Catalyst to Oil Weight Ratio on the Catalytic Conversion of Heavy Oil to Propylene Using ZSM-5 and USY Catalysts 被引量:10
2
作者 Xiaohong Li Chunyi Li Jianfang Zhang Chaohe Yang Honghong Shan 《Journal of Natural Gas Chemistry》 EI CAS CSCD 2007年第1期92-99,共8页
It is useful for practical operation to study the rules of production of propylene by the catalytic conversion of heavy oil in FCC (fluid catalytic cracking). The effects of temperature and C/O ratio (catalyst to o... It is useful for practical operation to study the rules of production of propylene by the catalytic conversion of heavy oil in FCC (fluid catalytic cracking). The effects of temperature and C/O ratio (catalyst to oil weight ratio) on the distribution of the product and the yield of propylene were investigated on a micro reactor unit with two model catalysts, namely ZSM-5/Al2O3 and USY/Al2O3, and Fushun vacuum gas oil (VGO) was used as the feedstock. The conversion of heavy oil over ZSM-5 catalyst can be comparable to that of USY catalyst at high temperature and high C/O ratio. The rate of conversion of heavy oil using the ZSM-5 equilibrium catalyst is lower compared with the USY equilibrium catalyst under the general FCC conditions and this can be attributed to the poor steam ability of the ZSM-5 equilibrium catalyst. The difference in pore topologies of USY and ZSM-5 is the reason why the principal products for the above two catalysts is different, namely gasoline and liquid petroleum gas (LPG), repspectively. So the LPG selectivity, especially the propylene selectivity, may decline if USY is added into the FCC catalyst for maximizing the production of propylene. Increasing the C/O ratio is the most economical method for the increase of LPG yield than the increase of the temperature of the two model catalysts, because the loss of light oil is less in the former case. There is an inverse correlation between HTC (hydrogen transfer coefficient) and the yield of propylene, and restricting the hydrogen transfer reaction is the more important measure in increasing the yield of propylene of the ZSM-5 catalyst. The ethylene yield of ZSM-5/A1203 is higher, but the gaseous side products with low value are not enhanced when ZSM-5 catalyst is used. Moreover, for LPG and the end products, dry gas and coke, their ranges of reaction conditions to which their yields are dependent are different, and that of end products is more severe than that of LPG. So it is clear that maximizing LPG and propylene and restricting dry gas and coke can be both achieved via increasing the severity of reaction conditions among the range of reaction conditions which LPG yield is sensitive to. 展开更多
关键词 fluid catalytic cracking heavy oil PROPYLENE temperature catalyst to oil weight ratio ZSM-5 USY
下载PDF
Low gas-liquid ratio foam flooding for conventional heavy oil 被引量:3
3
作者 Wang Jing Ge Jijiang Zhang Guicai Ding Baodong Zhang Li Jin Luchao 《Petroleum Science》 SCIE CAS CSCD 2011年第3期335-344,共10页
The recovery of heavy oil by water flooding is 10% lower than that of conventional crude oil, so enhanced oil recovery (EOR) is of great significance for heavy oil. In this paper, foam flooding with a gas-liquid rat... The recovery of heavy oil by water flooding is 10% lower than that of conventional crude oil, so enhanced oil recovery (EOR) is of great significance for heavy oil. In this paper, foam flooding with a gas-liquid ratio (GLR) of 0.2:1 for the Zhuangxi heavy oil (325 mPa.s at 55 ℃) was performed on cores, sand packs and plate model. In sand pack tests, polymer enhanced foam flooding increased oil recovery by 39.8%, which was 11.4% higher than that for alkali/surfactant/polymer (ASP) flooding under the same conditions. Polymer enhanced foam flooding in plate models shows that the low GLR foam flooding increased oil recovery by about 30%, even when the extended water flooding was finished at 90% water cut. Moreover, it was discovered by microscopy that foam was more stable in heavy oil than in light oil. These results confirm that low GLR foam flooding is a promising technology for displacing conventional heavy oil. 展开更多
关键词 Low gas-liquid ratio foam flooding enhanced oil recovery conventional heavy oil
下载PDF
Crude oil cracking in deep reservoirs:A review of the controlling factors and estimation methods 被引量:2
4
作者 Yu Qi Chun-Fang Cai +2 位作者 Peng Sun Dao-Wei Wang Hong-Jian Zhu 《Petroleum Science》 SCIE EI CAS CSCD 2023年第4期1978-1997,共20页
The natural cracking of crude oils in deep reservoirs has gained great interest due to continuously increasing depth of petroleum exploration and exploitation.Complex oil compositions and surroundings as well as compl... The natural cracking of crude oils in deep reservoirs has gained great interest due to continuously increasing depth of petroleum exploration and exploitation.Complex oil compositions and surroundings as well as complicated geological evolutions make oil cracking in nature much more complex than industrial pyrolysis.So far,numerous studies,focused on this topic,have made considerable progress although there still exist some drawbacks.However,a comprehensive review on crude oil cracking is yet to be conducted.This article systematically reviews the controlling factors of oil cracking from six aspects,namely,oil compositions,temperature and time,pressure,water,minerals and solid organic matter.We compare previous experimental and modelling results and present new field cases.In the following,we evaluate the prevailing estimation methods for the extent of oil cracking,and elucidate other factors that may interfere with the application of these estimation methods.This review will be helpful for further investigations of crude oil cracking and provides a guide for estimation of the cracking extent of crude oils. 展开更多
关键词 oil cracking Deep reservoir Controlling factor Gas to oil ratio Diamondoid
下载PDF
RNA/DNA Ratio and LPL and MyoD mRNA Expressions in Muscle of Oreochromis niloticus Fed with Elevated Levels of Palm Oil
5
作者 Christian Larbi AYISI ZHAO Jinliang 《Journal of Ocean University of China》 SCIE CAS 2016年第1期184-192,共9页
Palm oil is of great potential as one of the sustainable alternatives to fish oil(FO) in aquafeeds.In this present study,five isonitrogenous diets(32% crude protein) with elevated palm oil levels of 0%,2%,4%,6% and 8%... Palm oil is of great potential as one of the sustainable alternatives to fish oil(FO) in aquafeeds.In this present study,five isonitrogenous diets(32% crude protein) with elevated palm oil levels of 0%,2%,4%,6% and 8% were used during an 8-week feeding trial to evaluate its effects on RNA/DNA ratio and lipoprotein lipase(LPL) and Myo D m RNA expressions in muscle of Oreochromis niloticus.The results showed that RNA,DNA content as well as ratio of RNA to DNA were significantly affected(P < 0.05),in each case the highest was recorded in fish group subjected to 6% palm oil level.There was a strong positive correlation between nucleic acid concentration(RNA concentration and RNA:DNA ratio) and specific growth rate(SGR),protein efficiency ratio(PER),while a negative correlation existed between nucleic acid concentration(RNA concentration and RNA:DNA ratio) and feed conversion ratio(FCR).The m RNA expressions of LPL and Myo D in muscle were not significantly affected by the different palm oil levels,although the highest expression was observed in fish fed with 6% palm oil level.There also existed a strong positive correlation between the m RNA expression of LPL,Myo D and SGR,PER,while their correlation with FCR was negative.In conclusion,elevated palm oil affected the RNA,DNA concentration as well as RNA/DNA ratio significantly,although the m RNA expression of LPL and Myo D were not affected significantly by elevated palm oil levels. 展开更多
关键词 Oreochromis niloticus palm oil RNA: DNA ratio LPL MYOD gene expression
下载PDF
Effects of Use and Re-Use of Selected Vegetable Oils on the Proximate, Minerals, Mineral Ratios and Mineral Safety Index of Raw and Fried Plantain Chips: Note I
6
作者 Emmanuel Ilesanmi Adeyeye Adeolu Jonathan Adesina +1 位作者 Sulaiman Adeoye Olagboye Mercy Ayomadewa Olatunya 《Journal of Agricultural Chemistry and Environment》 2019年第2期92-106,共15页
Raw and fried plantain chips obtained from the use and re-use of olive, refined palm olein and coconut oils were investigated for the proximate, mineral compositions, computed mineral ratios and the mineral safety ind... Raw and fried plantain chips obtained from the use and re-use of olive, refined palm olein and coconut oils were investigated for the proximate, mineral compositions, computed mineral ratios and the mineral safety index using standard analytical methods. For the selected oils (both use and re-use): first and second re-use and the fresh plantain chips (unprocessed plantain chips;UPC) had the following range results: proximate composition (%) (moisture: 8.20 - 12.3, crude protein: 9.70 - 8.60, fat: 7.40 - 12.9, fibre: 3.50 - 4.90, ash: 2.80 - 3.80 and carbohydrates: 63.5 - 64.8), % energy contributions (PEC: 63.4 - 70.8, PEF: 20.2 - 28.6, PEP: 8.03 - 9.66, UEDP: 4.49 - 5.08). The mineral composition (mg/100g) of the samples had the following greater than 80.0: Ca, Mg, K and P;Fe, Cu, Mn and Zn recorded values ranging between 1.00 and 4.00;Co, Se and Ni had their concentrations between 0.00 and 0.0363 whereas Pb and Cd recorded levels lower than 0.0006. In the mineral ratios, only K/(Ca + Mg) values fell within the acceptable ideal range. No MSI aberration was observed for the minerals from all the samples obtained from the various oils. The chi-square analysis showed that on parameter wise comparisons, there were no significant differences among the levels as treated based on the various oils except gross energy, Mg, K, P, Ca/P, Fe/Pb and K/Co. Also on pairwise comparison from linear correlation and regression, all these parameters were significantly different at r = 0.01 between the unprocessed and fried plantain samples: proximate, percentage energy distribution, mineral and mineral ratios. Generally, the first (day) frying showed fairly high nutrient concentration than the first and second re-use oils products. Therefore, for optimum nutrient preservation from fried plantain chips re-use of oil for frying should be sparingly allowed. However, olive showed highest level of nutrients in terms of proximate and mineral compositions. 展开更多
关键词 Vegetable oilS PLANTAIN CHIPS PROXIMATE MINERALS ratios Safety Index
下载PDF
Evaluation of diagnostic ratios of medium and serious weathered oils from five different oil sources
7
作者 HE Shijie WANG Chuanyuan +2 位作者 LI Yantai YU Hongjun HAN Bin 《Acta Oceanologica Sinica》 SCIE CAS CSCD 2016年第4期1-8,共8页
Laboratory experiments were conducted to simulate oil weathering process, a medium to long term weathering process for 210-d, using samples collected from five different oil resources. Based on relative deviation and ... Laboratory experiments were conducted to simulate oil weathering process, a medium to long term weathering process for 210-d, using samples collected from five different oil resources. Based on relative deviation and repeatability limit analysis about indexes of these samples, the results show there had been significant changes in diagnostic ratios among the initial and weathered samples of different oils during this process. Changes of selected n-alkane diagnostic ratios of all oil samples displayed more obviously than diagnostic ratios of terpanes,steranes and PAHs in this process. Almost all selected diagnostic ratios of terpanes, steranes and PAHs can be efficiently used in tracking sources of hydrocarbon pollution, differentiating from the n-alkane diagnostic ratios.In these efficient diagnostic ratios, only four ratios maintained good stability in the weathering processes and are more suitable because their relative deviation(RSD) are lower than 5%. 展开更多
关键词 identification of spilled oils medium to long term weathering process simulation experiment biomarker ratios
下载PDF
Canadians Help Boost Oil Recovery Ratio
8
《China Oil & Gas》 CAS 1997年第4期244-244,共1页
关键词 HELP Canadians Help Boost oil Recovery ratio
下载PDF
Acquisition Practice of High Signal-to-Noise Ratio in YTB Block of Sichuan Basin
9
作者 Jun Wu Jiangli Chen +5 位作者 Zhong Li Zengyou Wu Hong Liu Yiwei Li Yong Tang Junguo Du 《Journal of Geoscience and Environment Protection》 2023年第6期229-236,共8页
YTB block in Sichuan basin is a favorable area to exploit oil and gas in shallow tight rock. 3D seismic project of this zone has two characteristics. Firstly, it has high requirements for the tolerance rate of the con... YTB block in Sichuan basin is a favorable area to exploit oil and gas in shallow tight rock. 3D seismic project of this zone has two characteristics. Firstly, it has high requirements for the tolerance rate of the construction process and the acquisition of high signal-to-noise ratio seismic data;Second, there are widely obstacles and noises that lead to difficult acquisition construction organization. In acquisition practice, high signal-to-noise ratio seismic data was obtained by reasonable design of construction scheme, optimization of excitation parameters, improvement of receiving conditions and optimization of obstacle crossing observation system. . 展开更多
关键词 Tight oil and Gas Tolerance Rate High Signal-to-Noise ratio OBSTACLE
下载PDF
页岩油蓄能体积压裂开发效果预测与评价方法
10
作者 许宁 陈哲伟 +4 位作者 许琬晨 王玲 崔晓磊 蒋美忠 战常武 《油气藏评价与开发》 CSCD 北大核心 2024年第5期741-748,755,共9页
蓄能体积压裂(以下简称蓄压)是页岩油藏提前补充地层能量、大幅提升单井产量的主要开发方式,应用广泛。通过渗吸与驱替机理结合实际生产数据统计分析,提出了根据返排率预测蓄压开发阶段最大累计产油量方法。研究结果表明:返排率30%之后... 蓄能体积压裂(以下简称蓄压)是页岩油藏提前补充地层能量、大幅提升单井产量的主要开发方式,应用广泛。通过渗吸与驱替机理结合实际生产数据统计分析,提出了根据返排率预测蓄压开发阶段最大累计产油量方法。研究结果表明:返排率30%之后,蓄压的累计产油量与返排率对数呈强线性相关,可预测压后单井最大累计产油量;该方法已经得到其他页岩油藏实际生产数据的实证,较递减曲线分析法更加准确且更具普适性,是对储层条件、压裂规模与工艺、焖排采工作制度等主客观因素的综合评价。返排率法可进一步确定液油比和合理返排速度。蓄压排采的平均返排速度控制在6~8 m^(3)(/d·km),与渗吸排油速度相匹配,能够更加高效地利用蓄压补充的弹性能量,取得较高采收率和较低的液油比。单井压后最大可采油量的返排率预测法为蓄压的经济效益评价、生产制度优化、压裂成本控制等提供了依据,对地质-工程一体化、优化井网井距和压裂设计具有重要指导意义。 展开更多
关键词 返排率 蓄能 压裂 采收率 累计产油量
下载PDF
稠油提高采收率技术现状及发展趋势
11
作者 王学慧 代玉杰 赵阳 《现代化工》 CAS CSCD 北大核心 2024年第10期34-38,43,共6页
综述了目前稠油开采的主要方式,介绍了稠油热采技术、化学驱油、二氧化碳驱油、微生物驱油以及电磁加热等稠油开采技术的现状。分析了上述稠油开发技术的优势和不足,对稠油开发方式的发展趋势进行了预测。指出兼顾效益和环保是未来稠油... 综述了目前稠油开采的主要方式,介绍了稠油热采技术、化学驱油、二氧化碳驱油、微生物驱油以及电磁加热等稠油开采技术的现状。分析了上述稠油开发技术的优势和不足,对稠油开发方式的发展趋势进行了预测。指出兼顾效益和环保是未来稠油开发的发展趋势。热采碳排放较多,化学驱油容易带来环境污染和水处理困难等系列问题。清洁能源有利于实现稠油开发,提升稠油开采质量。 展开更多
关键词 稠油 采收率 现状 趋势
下载PDF
纳米材料在油田开发领域的研究及应用
12
作者 孙玉海 吕博 +2 位作者 卢占国 张志杰 陈志 《广州化工》 CAS 2024年第6期17-21,25,共6页
可利用石油资源逐渐减少、开采难度在增大。纳米材料具有卓越的粒子尺寸和性能,通过表面改性还可在同一纳米材料上集成多种驱油功能,其被认为是解决传统提高采收率(EOR)技术所面临众多问题的潜在方案。本文主要介绍了纳米材料的制备与... 可利用石油资源逐渐减少、开采难度在增大。纳米材料具有卓越的粒子尺寸和性能,通过表面改性还可在同一纳米材料上集成多种驱油功能,其被认为是解决传统提高采收率(EOR)技术所面临众多问题的潜在方案。本文主要介绍了纳米材料的制备与改性、种类,综述其在油田开发各阶段的应用与研究进展,特别是EOR方面。结合油田开发需求与纳米技术的优势,指出了纳米颗粒在EOR过程中应用的挑战和未来研究的机遇。 展开更多
关键词 纳米材料 驱油剂 油田开发 采收率
下载PDF
准噶尔盆地东南缘页岩油储层脆性预测与评价
13
作者 于正军 张军华 +3 位作者 周昊 任瑞军 陈永芮 杨玉龙 《吉林大学学报(地球科学版)》 CAS CSCD 北大核心 2024年第5期1711-1723,共13页
准噶尔盆地东南缘二叠系中下部发育页岩油致密储层,脆性预测与评价对其勘探和开发有重要意义。本文利用岩石物理实验、测井资料和叠前地震资料计算了准噶尔盆地东南缘二叠系页岩油致密储层脆性指数,对Rickman经典公式法、杨氏模量与泊... 准噶尔盆地东南缘二叠系中下部发育页岩油致密储层,脆性预测与评价对其勘探和开发有重要意义。本文利用岩石物理实验、测井资料和叠前地震资料计算了准噶尔盆地东南缘二叠系页岩油致密储层脆性指数,对Rickman经典公式法、杨氏模量与泊松比比值法、拉梅系数法和剪切模量法进行了比较、分析与评价。研究认为:1)杨氏模量相对泊松比对岩性有更好的区分度,由拉梅系数表征的泥岩分布率较高;2)根据文献所得测井多参数计算脆性指数的方法应用效果不佳,在Castagna经验公式换算横波速度基础上计算的脆性指数具有较好的应用效果;3)由YPD(Young's modulus-Poisson's ratio-density)式和LMR(拉梅系数-密度)式反演的弹性参数变化率也能较好地指示有利储层,尤以密度变化率为最佳,该属性在扇三角洲前缘及分流河道特征上得到很好的展示;4)岩石物理实验和实际资料应用均表明,ρE/σ为研究区脆性的最佳表征公式,效果好于Rickman经典公式与其他方法。 展开更多
关键词 准噶尔盆地 致密储层 页岩油 岩石物理实验 横波速度 杨氏模量 泊松比 脆性指数
下载PDF
井底压力下牙轮钻头浮动套轴承性能分析
14
作者 钟林 冷晓栋 +3 位作者 王国荣 王娟 魏刚 伍小龙 《润滑与密封》 CAS CSCD 北大核心 2024年第7期15-22,49,共9页
为了探究井底压力下215.9 mm牙轮钻头浮动套轴承的平衡转速比、摩擦学性能、油膜压力分布随内外间隙比的变化规律,修正了考虑浮动套轴承实际井下环境压力和牙轮钻头密封压差的Reynolds边界条件,利用MATLAB中的PDE Toolbox对浮动套轴承Re... 为了探究井底压力下215.9 mm牙轮钻头浮动套轴承的平衡转速比、摩擦学性能、油膜压力分布随内外间隙比的变化规律,修正了考虑浮动套轴承实际井下环境压力和牙轮钻头密封压差的Reynolds边界条件,利用MATLAB中的PDE Toolbox对浮动套轴承Reynolds方程进行数值求解,分析内外间隙比对浮动套轴承平衡转速比、油膜压力及摩擦因数的影响规律,结果表明:当环境压力为60 MPa、密封压差为20 MPa时,随内外间隙比增加,浮动套平衡转速比呈现先增大后减小的趋势;以轴承的摩擦因数和油膜压力作为综合评价指标,钻头浮动套轴承内外间隙比为2.0时,轴承的摩擦因数较小,油膜压力较高,其轴承综合性能较优;而当浮动套轴承内外间隙比为2.0时,随着环境压力的升高,浮动套轴承的摩擦扭矩和摩擦因数增加,从而加剧轴承的磨损。该研究为牙轮钻头浮动套轴承的结构参数优化及性能提升提供了基础理论支撑。 展开更多
关键词 井底压力 牙轮钻头浮动套轴承 内外间隙比 油膜压力 摩擦因数
下载PDF
原油中C_(19-49)长链三环萜烷系列及其地球化学意义——以柴达木盆地西部英西地区原油为例
15
作者 包建平 朱翠山 +3 位作者 杨茜 陈琰 周飞 张静 《沉积学报》 CAS CSCD 北大核心 2024年第5期1765-1783,共19页
【目的】为了确定柴达木盆地西部英西地区古近系深部储层(E)原油的热演化程度和成因类型,【方法】利用色谱—质谱(GC-MS)和色谱—质谱—质谱(GC-MS-MS)技术,对其中的各类生物标志物、烷基菲和金刚烷类化合物的分布与组成特征进行了系统... 【目的】为了确定柴达木盆地西部英西地区古近系深部储层(E)原油的热演化程度和成因类型,【方法】利用色谱—质谱(GC-MS)和色谱—质谱—质谱(GC-MS-MS)技术,对其中的各类生物标志物、烷基菲和金刚烷类化合物的分布与组成特征进行了系统分析。【结果与讨论】分析结果表明该地区原油中正构烷烃系列均具有明显的偶碳优势,Pr/Ph比值低(<0.60),Ph/nC_(18)比值高(>1.30),伽马蜡烷含量高,伽马蜡烷指数介于0.90~1.36,属于典型咸水湖相原油,这与研究区古近纪的沉积特征一致。但依据不同原油中长链三环萜烷系列的分布与组成特征,可将他们分成两类:一类原油中C_(19-49)长链三环萜烷系列异常丰富,C_(19-30)TT/C_(27-35)H比值大于1.60,C_(23)TT/C_(30)H>1.40,并伴随有高甾藿比(>4.50)和高β-胡萝烷/nC_(37)比值(>3.20),表明藻类是其主要原始生烃母质;另一类原油中C_(19-30)长链三环萜烷系列含量中等,C_(19-30)TT/C_(27-35)H比值小于0.50,C_(23)TT/C_(30)H<0.55,其甾藿比相对较低(<2.0)、β-胡萝卜烷含量中等,β-胡萝烷/nC_(37)比值小于1.50,可见此类原油中藻类的贡献明显低于前一类原油。对比它们的甾、萜烷和金刚烷类化合物成熟度参数,发现这两组原油的成熟度相近,其对应的R_(o)值介于1.1%~1.3%,即它们形成于生油高峰之后、凝析油气形成以前这一演化阶段。【结论】影响研究区原油中长链三环萜烷系列相对丰度的主要因素是原始生烃母质,而非成熟度,因而它在研究区具有指示原油成因类型的作用,在后续油气勘探中应重点关注。 展开更多
关键词 藿烷系列 C_(19-49)长链三环萜烷系列 伽马蜡烷 β-胡萝卜烷 甾藿比 原油 英西地区 柴达木盆地西部
下载PDF
断溶体油藏追踪油水界面变化的新方法
16
作者 刘培亮 李成刚 蒋林 《广东石油化工学院学报》 2024年第1期11-14,共4页
在底水驱动型断溶体油藏中确定原始油水界面及追踪动态油水界面变化一直是制约剩余油预测的重要难题。此文聚焦油水界面的油藏本质,精细量化了储集体的孔隙体积,开发动态数据试井化处理计算水油体积比,动静结合等比例分配油水体积计算... 在底水驱动型断溶体油藏中确定原始油水界面及追踪动态油水界面变化一直是制约剩余油预测的重要难题。此文聚焦油水界面的油藏本质,精细量化了储集体的孔隙体积,开发动态数据试井化处理计算水油体积比,动静结合等比例分配油水体积计算出原始油水界面。在油藏内部划分出油水界面,后期根据水驱动用过程评估曲线划分水驱阶段,追踪动态油水界面变化,避免陷入前期常规方法选取参数困难、计算误差大的困境。开发实践证实该方法得到的结果误差小,计算方便快捷,具有推广应用前景。 展开更多
关键词 缝洞型油藏 断溶体 水油体积比 油水界面
下载PDF
微波含水率检测技术在复杂油水混合形态下的应用研究
17
作者 许国晨 宋宗旭 +2 位作者 张磊 孟敏 曹聪 《中外能源》 CAS 2024年第5期60-67,共8页
在油水混合物中会出现不同的乳化形态,不同的乳化形态对应的电导率和介电常数也具有显著差异,从而导致通过检测电导率和介电常数值间接测量含水率的测量结果不准确。针对复杂油水混合状态下含水率难以测准的问题,提出一种基于微波技术... 在油水混合物中会出现不同的乳化形态,不同的乳化形态对应的电导率和介电常数也具有显著差异,从而导致通过检测电导率和介电常数值间接测量含水率的测量结果不准确。针对复杂油水混合状态下含水率难以测准的问题,提出一种基于微波技术的复杂油水两相流含水率检测技术,建立了基于微波技术的“油包水”和“水包油”状态分析方法。首先通过检测微波信号穿过不同介质后信号幅值的衰减和相位的偏移,推测油水混合物的含水率值。再利用不同输入功率的微波信号在不同介电常数下功率衰减比不同的原理,来区分油水混合物的乳化状态,优化含水率的测量。室内验证和矿场试验结果表明,该系统可有效区分乳化液的混合状态,通过含水率标定值对实测数据进行修正,最终测量的含水率误差可控制在1个百分点以内,实现了复杂油水混合形态下含水率的高精度测量。 展开更多
关键词 油水混合物 含水率测量 乳化状态 微波信号 介电常数 功率衰减比
下载PDF
油液多层过滤去固分离及特性分析
18
作者 龚海峰 唐治知 +3 位作者 彭烨 梁鑫鑫 余保 李书龙 《石油学报(石油加工)》 EI CAS CSCD 北大核心 2024年第2期523-533,共11页
针对油-固体系中单层滤网无法同时满足过滤精度高与使用寿命长的问题,采用多层过滤器并对其去固分离特性展开分析。通过耦合流场控制方程、颗粒运动方程、颗粒-壁面碰撞模型方程,建立了适用油-固体系的多层过滤数值分析模型,探究了油-... 针对油-固体系中单层滤网无法同时满足过滤精度高与使用寿命长的问题,采用多层过滤器并对其去固分离特性展开分析。通过耦合流场控制方程、颗粒运动方程、颗粒-壁面碰撞模型方程,建立了适用油-固体系的多层过滤数值分析模型,探究了油-固体系中多层过滤器的去固分离特性,分析了入口流速和滤网层数对流场特性及过滤比(β)的影响。结果表明:多层过滤器可有效过滤孔径与粒径比(k_(d))大于15的固体颗粒;增加滤网层数,d_(5)和d_(20)(β分别为5和20时对应的颗粒粒径)显著降低;增大入口流速,d_(5)和d_(20)变化较小;当β<5时,颗粒粒径的变化对过滤比的影响较小;当β>5时,颗粒粒径的小幅增大可能导致过滤比显著提高。 展开更多
关键词 多层过滤 油-固分离 流场特性 碰撞模型 过滤比 分布云图
下载PDF
延长油田H区块剩余油分布规律及开发技术研究
19
作者 王攀 李海峰 +2 位作者 程永福 汪昌尧 郝江涛 《云南化工》 CAS 2024年第8期164-168,共5页
为了更好的明确延长油田H区域剩余油的分布特征、开发潜力,以及有效的开发策略,运用油藏工程、动态监测、数值模拟相结合的方法,认识剩余油分布规律及主控因素,进一步揭示剩余油分布特征,为下一步注水开发提供理论基础。依据油藏工程及... 为了更好的明确延长油田H区域剩余油的分布特征、开发潜力,以及有效的开发策略,运用油藏工程、动态监测、数值模拟相结合的方法,认识剩余油分布规律及主控因素,进一步揭示剩余油分布特征,为下一步注水开发提供理论基础。依据油藏工程及数值模拟精细描述成果,提出了能够提高采收率的合理注采比及地层压力保持水平,优选出中高含水阶段密井网下合理的开发技术,为研究区高效注水开发提供可靠的技术支撑。 展开更多
关键词 延长油田 剩余油 主控因素 开发层系 合理注采比 合理注采井距
下载PDF
“双碳”目标下油气行业固定资产投资对碳排放的影响研究
20
作者 范秋芳 高梦琦 刘浩旻 《资源与产业》 2024年第3期36-47,共12页
为了厘清油气行业固定资产投资与碳排放之间的关系,本文将2002—2021年我国油气行业面板数据作为研究样本,通过构建固定效应模型实证研究了油气行业固定资产投资对碳排放的影响作用,并采用中介效应模型,运用逐步回归方法验证了油气行业... 为了厘清油气行业固定资产投资与碳排放之间的关系,本文将2002—2021年我国油气行业面板数据作为研究样本,通过构建固定效应模型实证研究了油气行业固定资产投资对碳排放的影响作用,并采用中介效应模型,运用逐步回归方法验证了油气行业固定资产投资、人均研发投入与碳排放之间的作用关系及其影响机制。研究结果表明:1)油气行业固定资产投资显著降低了碳排放比值,其影响系数为-1.913,表明通过加大油气行业的固定资产投资能够显著降低该行业的二氧化碳排放。本文在运用替换被解释变量、替换解释变量,以及增加控制变量等方法开展进一步回归分析后发现,上述检验结果依然稳健。2)人均研发投入在固定资产投资与碳排放比值之间发挥着部分中介作用,其中介效应值为24.7%。此外,油气行业的固定资产投资还显著降低了人均研发投入,而人均研发投入通过推动绿色技术创新则可以有效抑制碳排放比值。3)油气行业固定资产投资对碳排放的影响作用是短期的且影响系数较小,对主营业务收入的影响作用是长期的且影响系数较大。4)在我国油气行业的稳定增长时期与转型升级时期之内,固定资产投资对碳排放比值的影响作用具有明显的差异性。异质性检验结果表明,在油气行业的稳定增长期内,固定资产投资与碳排放比值之间并无显著的相关关系,而在油气行业的转型升级期内,固定资产投资则显著抑制了碳排放比值。 展开更多
关键词 油气行业 碳排放比值 固定资产投资 人均研发投入
下载PDF
上一页 1 2 109 下一页 到第
使用帮助 返回顶部