Tungsten (W) incorporated mobil-type eleven (MEL) zeolite membrane (referred to as W-MEL membrane) with high separation performance was firstly explored for the separation of oil/water mixtures under the influence of ...Tungsten (W) incorporated mobil-type eleven (MEL) zeolite membrane (referred to as W-MEL membrane) with high separation performance was firstly explored for the separation of oil/water mixtures under the influence of gravity.W-MEL membranes were grown on stainless steel (SS) meshes through in-situ hydrothermal growth method facilitated with (3-aminopropyl)triethoxysilane (APTES) modification of stainless steel meshes,which promote the heterogeneous nucleation and crystal growth of W-MEL zeolites onto the mesh surface.W-MEL membranes were grown on different mesh size supports to investigate the effect of mesh size on the separation performance of the membrane.The assynthesized W-MEL membrane supported on 500 mesh (25μm)(W-MEL-500) exhibit the hydrophilic nature with a water contact angle of 11.8°and delivers the best hexane/water mixture separation with a water flux and separation efficiency of 46247 L·m^(-2)·h^(-1)and 99.5%,respectively.The wettability of W-MEL membranes was manipulated from hydrophilic to hydrophobic nature by chemically modifying with the fluorine-free compounds (hexadecyltrimethoxysilane (HDTMS) and dodecyltrimethoxysilane(DDTMS)) to achieve efficient oil-permselective separation of heavy oils from water.Among the hydrophobically modified W-MEL membranes,W-MEL-500-HDTMS having a water contact angle of146.4°delivers the best separation performance for dichloromethane/water mixtures with a constant oil flux and separation efficiency of 61490 L·m^(-2)·h^(-1)and 99.2%,respectively along with the stability tested up to 20 cycles.Both W-MEL-500-HDTMS and W-MEL-500-DDTMS membranes also exhibit similar separation performances for the separation of heavy oil from sea water along with a 20-fold lower corrosion rate in comparison with the bare stainless-steel mesh,indicating their excellent stability in seawater.Compared to the reported zeolite membranes for oil/water separation,the as-synthesized and hydrophobically modified W-MEL membranes shows competitive separation performances in terms of flux and separation efficiency,demonstrating the good potentiality for oil/water separation.展开更多
In this paper, the superhydrophobic polyurethane sponge(SS-PU) was facilely fabricated by etching with Jones reagent to bind the nanoparticles of Ni-Co double layered oxides(LDOs) on the surface, and following modific...In this paper, the superhydrophobic polyurethane sponge(SS-PU) was facilely fabricated by etching with Jones reagent to bind the nanoparticles of Ni-Co double layered oxides(LDOs) on the surface, and following modification with n-dodecyl mercaptan(DDT). This method provides a new strategy to fabricate superhydrophobic PU sponge with a water contact angle of 157° for absorbing oil with low cost and in large scale. It exhibits the strong absorption capacity and highly selective characteristic for various kinds of oils which can be recycled by simple squeezing. Besides, the as-prepared sponge can deal with the floating and underwater oils, indicating its application value in handling oil spills and domestic oily wastewater. The good self-cleaning ability shows the potential to clear the pollutants due to the ultralow adhesion to water. Especially, the most important point is that the superhydrophobic sponge can continuously and effectively separate the oil/water mixture against the condition of turbulent disturbance by using our designed device system, which exhibit its good superhydrophobicity, strong stability.Furthermore, the SS-PU still maintained stable absorption performance after 150 cycle tests without losing capacity obviously, showing excellent durability in long-term operation and significant potential as an efficient absorbent in large-scale dispose of oily water.展开更多
The membrane method based on adaptive wettability shows great advantages in oil-water separation.At present,researches focus on the excellent application performance of the membrane material,while the quantitative ana...The membrane method based on adaptive wettability shows great advantages in oil-water separation.At present,researches focus on the excellent application performance of the membrane material,while the quantitative analysis of interactions in oil-water separation is rarely recognized.Herein,we constructed an adaptable wettability membrane with multiple polymer networks by polydopamine(PDA)and mussel-inspired amphiphilic polymer.Based on the Owens three-probe liquid method,the surface energy of the modified membrane was verified to meet the adaptive wettability conditions,with surface energies(γ-8)of 147.6 mJ m^(−2)(superhydrophilic/underwater superoleophobic)and 49.87 mJ m^(−2)(superhydrophobic/superoleophobic),respectively.The adhesion or repulsion of the membrane to the oil phase under different conditions during the separation process was quantified by the chemical probe AFM technique.In addition,the oil-water selective separation mechanism was further analyzed in a simplified membrane microchannel model.The results show that the different wetting produces capillary additional pressure in opposite directions,resulting in different energies to be overcome when the oil or water passes through the microchannels,thus achieving selective separation.展开更多
In this work, a simple method was carried out to successfully fabricate superoleophilic and superhydrophobic N-dodecyltrimethoxysilane@tungsten trioxide coated copper mesh. The as-fabricated copper mesh displayed prom...In this work, a simple method was carried out to successfully fabricate superoleophilic and superhydrophobic N-dodecyltrimethoxysilane@tungsten trioxide coated copper mesh. The as-fabricated copper mesh displayed prominent superoleophilicity and superhydrophobicity with a huge water contact angle about 154.39° and oil contact angle near 0° Moreover, the coated copper mesh showed high separation efficiency approximately 99.3%, and huge water flux about 9962.3 L·h^-1·m-2, which could be used to separate various organic solvents/ water mixtures. Furthermore, the coated copper mesh showed favorable stability that the separation efficiency remained above 90% after 10 separation cycles. Benefiting from the excellent photocatalytic degradation ability of tungsten trioxide, the coated copper mesh possessed the self-cleaning capacity. Therefore, the mesh contaminated with lubricating oil could regain superhydrophobic property, and this property of self-cleaning permitted that the fabricated copper mesh could be repeatedly used for oil and water separation.展开更多
Studies on nonlinear behavior at oil/water interface membrane were performed. This system showed rhythmic oscillations and chaos of electrical potential in a given concentration domain. The nonlinear behavior response...Studies on nonlinear behavior at oil/water interface membrane were performed. This system showed rhythmic oscillations and chaos of electrical potential in a given concentration domain. The nonlinear behavior response at the liquid membrane apparently resembled that of biological chemoreceptive membrane. The possibility of developing a new type of chemical sensor with the ability to simulate substance equilibrium in living organisms was suggested in the paper.展开更多
It is of great necessity yet still a challenge to develop superwetting functional interfacial materials for simultaneously separating insoluble oil and degrading soluble dye pollutants in practical wastewater.In this ...It is of great necessity yet still a challenge to develop superwetting functional interfacial materials for simultaneously separating insoluble oil and degrading soluble dye pollutants in practical wastewater.In this work,a Ag-CuO heterostructure-decorated mesh was fabricated via facile alkali etchingcalcination and photoreduction approaches.The as-synthesized mesh with superhydrophilicity and underwater superoleophobicity displayed high separation efficiency(>99.998%)for diverse oil/water mixtures.Besides,it demonstrated more superior photocatalytic performance in dye degradation than those of bare CuO nanostructure-coated materials,which is primarily attributed to the intensive visible light harvesting and efficient electron-holes separation occurred on noble metal-semiconductor heterostructures.Furthermore,on account of the tenacity of Cu substrate as well as enhanced structural stability,this binary composite-decorated mesh exhibited highly reliable durability and robustness after 10 cycles of photocatalytic degradation tests,and even being ultrasonic worn for 30 min.More importantly,our developed mesh was capable of in situ catalytic degrading water-soluble organic dyes during oil/water separation under visible light irradiation.Therefore,such a dexterous and feasible strategy may afford a new route to construct bifunctional and predurable materials for actual sewage purification.展开更多
Nowadays, oil spills have led to a serious environmental crisis of the world. To deal with this problem, inspired from super-hydrophobic lotus leaf, this study fabricated super-hydrophobic and super-lipophilic functio...Nowadays, oil spills have led to a serious environmental crisis of the world. To deal with this problem, inspired from super-hydrophobic lotus leaf, this study fabricated super-hydrophobic and super-lipophilic functionalized graphene oxide/polyurethane(FGP) sponge by a simple and inexpensive dip coating method. The resulting FGP sponge was characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and water contact angle. The results expressed that FGP sponge exhibited a similar surface structure to that of a lotus leaf, and possessed the super-hydrophobic characteristic with the water contact angle(WAC) of 152°±1°. The absorption capacity and reusability were also investigated. It can be seen that, the FGP sponge can remove a wide range of oils and organic solvents from water with good absorption capacities(up to 35 times of its own mass). Significantly, after 10 cycles the absorption capacity of the oils and organic solvents was higher than 90%for the reused FGP sponge, demonstrating the good reusability of the FGP sponge. Therefore, this study probably provided a simple way to remove the pollutions of oil spills and toxic organism from water.展开更多
Polyethylene glycol(PEG) membranes with different molecular mass cut-offs were used to treat oil/water emulsion, and the effects of experimental conditions including pressure, temperature and different opera- ting mod...Polyethylene glycol(PEG) membranes with different molecular mass cut-offs were used to treat oil/water emulsion, and the effects of experimental conditions including pressure, temperature and different opera- ting modes on permeate flux and removal rate of chemical oxygen demand (COD_ Cr) were studied. The results show that the permeate flux of ultrafiltration membrane is influenced by pressure and temperature; practical pressure is chosen to be 0.30.7MPa for the PEG with molecular mass cut-offs of 8000 and 0.71.0 MPa for the PEG with molecular mass cut-offs of 2500; and the practical temperature is chosen to be 2532℃. Different operating modes of ultrafiltration also influence the permeate flux and removal rate of COD_ Cr. The ultrafiltration membrane of intermittent cross-flow operating mode is easier to be influenced by blocky polarization and contamination than that of sequential cross-flow operating mode. Removal rate of COD_ Cr in intermittent cross-flow and sequential cross-flow condition can be maintained at about 93%.展开更多
Alkaline-surfactant-polymer (ASP) flooding using sodium hydroxide as the alkali component to enhance oil recovery in Daqing Oilfield, northeast China has been successful, but there are new problems in the treatment ...Alkaline-surfactant-polymer (ASP) flooding using sodium hydroxide as the alkali component to enhance oil recovery in Daqing Oilfield, northeast China has been successful, but there are new problems in the treatment of produced crude. The alkali added forms stable water-in-crude oil emulsion, hence de-emulsification process is necessary to separate oil and water. The problems in enhanced oil recovery with ASP flooding were investigated in laboratory by using fractions of Daqing crude oil. The oil was separated into aliphatics, aromatics, resin and asphaltene fractions. These fractions were then mixed with an additive-free jet fuel to form model oils. The interfacial properties, such as interfacial tension and interracial pressure of the systems were also measured, which together with the molecular parameters of the fractions were all used to investigate the problems in the enhanced oil recovery. In our work, it was found that sodium hydroxide solution reacts with the acidic hydrogen in the fractions of crude oil and forms soap-like interfacially active components, which accumulate at the crude oil-water interface.展开更多
Produced water from an oil extraction site in South Kuwait was sampled after primary oil – water separation had been carried out. The produced water was filtered through a mixture of activated charcoal and esterified...Produced water from an oil extraction site in South Kuwait was sampled after primary oil – water separation had been carried out. The produced water was filtered through a mixture of activated charcoal and esterified cellulosic material gained from spent coffee grounds as a tertiary adsorption treatment. The earth-alkaline metal ions and heavy metals were separated from the de-oiled produced water by addition of either sodium or potassium hydroxide in the presence of carbon dioxide or by direct addition of solid sodium carbonate. The resulting filtrate gave salt of industrial purity upon selective crystallization on evaporation.展开更多
Produced water (PW) is the largest waste stream in the oil and gas industry. Water remains trapped for millions of years in the reservoir with oil and gas. When a hydrocarbon reservoir is infiltrated by a production w...Produced water (PW) is the largest waste stream in the oil and gas industry. Water remains trapped for millions of years in the reservoir with oil and gas. When a hydrocarbon reservoir is infiltrated by a production well, the produced fluids commonly contain water. The understanding of this water’s constituents and volumes is vital for the sustainable continuity of production operations, as PW has a number of negative impacts on the infrastructure integrity of the operation. On the other hand, PW can be an alternative source of irrigation water as well as of industrial salt. Interestingly, both the quantity as well as the quality of PW do not remain constant but can vary, both progressively and erratically, even over short periods of time. This paper discusses such a situation of variable PW in an oil and gas operation in the State of Kuwait.展开更多
Oil-water separation for produced water (PW) originating from an oil extraction site in South Kuwait was carried out using bleached, esterified cellulosic material from used coffee grounds. Thereafter, earth-alkaline ...Oil-water separation for produced water (PW) originating from an oil extraction site in South Kuwait was carried out using bleached, esterified cellulosic material from used coffee grounds. Thereafter, earth-alkaline metal ions, specifically calcium ions, of the de-oiled PW were removed by precipitation with sodium carbonate to give access to pure sodium chloride as industrial salt from the remaining PW. While the purity of the precipitated calcium carbonate (CaCO3) depends on the precipitation conditions, CaCO3 of up to 95.48% purity can be obtained, which makes it a salable product. The precipitation of CaCO3 decreases the amount of calcium ions in PW from 11,300 ppm to 84 ppm.展开更多
In recent years,numerous studies have been reported for oil/water separation,such as superoleophilic materials for oil absorption and underwater superoleophobic membranes for continuous separation.However,for the reco...In recent years,numerous studies have been reported for oil/water separation,such as superoleophilic materials for oil absorption and underwater superoleophobic membranes for continuous separation.However,for the recovery of oil slick pollution on near-shore ocean surface caused by various reasons,large area and fast availability of used materials are needed to be considered.Herein,we report an efficient and environmentally friendly method to fast process nylon mesh by surface diffuse atmospheric plasma(SDAP)for large-area oil/water separation.Nylon mesh is funcionalized by atmospheric plasma to generate micro/nano composite structures on the surface,resulting in superhydrophilicity and underwater superoleophobicity within only seconds.The pre-wetted modified nylon mesh can achieve high efficiency(>99.9%)and circulating water flux(~30,000 L·m^(-2)·h^(-1)),with high intrusion pressure(~3 kPa)and universality in oil/water separation.Regular plasma unconditionally generated in the atmosphere with the merit of efficiently functionalizing surface has the potential of large-area materials treatment.This study might take one step further for large-area industrial oily wastewater recovery and even oil slicks collection in near-shore water bodies.展开更多
Because of the increasing amount of oily wastewater produced each day,it is important to develop superhydrophilic/underwater superoleophobic oil/water separation membranes with ultrahigh flux and high separation effic...Because of the increasing amount of oily wastewater produced each day,it is important to develop superhydrophilic/underwater superoleophobic oil/water separation membranes with ultrahigh flux and high separation efficiency.In this paper,a superhydrophilic/underwater superoleophobic N-isopropylacrylamide-coated stainless steel mesh was prepared through a simple and convenient graft polymerization approach.The obtained mesh was able to separate oil/water mixtures only by gravity.In addition,the mesh showed high-efficiency separation ability(99.2%)and ultrahigh flux(235239 L·m^(−2)·h^(−1)).Importantly,due to the complex cross-linked bilayer structure,the prepared mesh exhibited good recycling performance and chemical stability in highly saline,alkaline and acidic environments.展开更多
We report the use of CaTiO_(3):Pr^(3+)multiband persistent luminescent nanoparticles,which can simultaneously emit red(610 nm),near-infrared(893 nm),and short-wave infrared(1040 nm)photoluminescence and persistent lum...We report the use of CaTiO_(3):Pr^(3+)multiband persistent luminescent nanoparticles,which can simultaneously emit red(610 nm),near-infrared(893 nm),and short-wave infrared(1040 nm)photoluminescence and persistent luminescence,as the tracer nanoagents for water tracer sensing.By using a spectrofluorometer,an Si charge-coupled device(CCD)camera and an InGaAs array camera as the detection tools,we evaluated the sensing capabilities of the three emission bands of CaTiO_(3):Pr^(3+)nanoparticles in brine water solutions and crude oil/brine water emulsions in both photoluminescence mode and persistent luminescence mode.Among these different detection combinations,the persistent luminescence-based Si CCD camera imaging exhibits the best sensing performance with the detection limits being at a single-digit ppb level for the 610 and 893 nm bands and about 100–200 ppb for the 1040 nm band in both water solutions and crude oil/water emulsions,while the photoluminescencebased Si CCD camera imaging has a much higher detection limit of~10 ppm in water solutions and of~200 ppm in oil/water emulsions.The persistent luminescence-based InGaAs array camera imaging to the 1040 nm band has the worst performance with the detection limits higher than 200 ppm for both solutions.The sensing performances of the spectrofluorometer to photoluminescence signals and persistent luminescence signals in the two solutions are about the same,with the detection limits being around 100–200 ppm.展开更多
The comparative effectiveness of remediating water polluted with crude oil, using environment-friendly bacteria (Pseudomonas aeruginosa) and fungi (Aspergillus niger) were investigated. The samples were separately tre...The comparative effectiveness of remediating water polluted with crude oil, using environment-friendly bacteria (Pseudomonas aeruginosa) and fungi (Aspergillus niger) were investigated. The samples were separately treated with Aspergillus niger and Pseudomonas aeruginosa. The bioremediation kinetic efficiency for these systems was studied. At the end of the bioremediation periods, the oil and grease content of the samples decreased from 47.0 mg/L in the untreated sample to 7.0 mg/L after 20 days when inoculated with bacteria while the sample inoculated with fungi decreased to 10.0 mg/L. Post analysis when inoculated with bacteria showed a fall in the value of the biological oxygen demand (BOD) from 73.84 mg/L to 33.28 mg/L after 20 days, while, the fungi inoculated sample showed a reduction from 73.84 mg/L to 38.48 mg/L. The biodegradation process with the bacteria was consistent with the pseudo-first-order model with a rate constant of 0.0891 day<sup>-1</sup>, while the biodegradation process with the fungi was consistent with the first order reaction model with a rate constant of 0.422 day<sup>-1</sup>. The degree of degradation after the 20<sup>th</sup> day of inoculation with Pseudomonas aeruginosa was 85.11%, while with Aspergillus niger was 78.72%. Thus, the results obtained showed that, Pseudomonas aeruginosa performed better than Aspergillus niger. The bioremediation data with fungi fitted the first-order model, while that of the bacteria fitted the pseudo-first-order model. Therefore, the data obtained in this study could be applied in the design of a bioremediation system for potential application to remediation of crude oil polluted water.展开更多
In today’s society, with the continuous growth of energy demand, Bohai Oilfield, as an important offshore oil resource base in China, is facing increasingly severe challenges while contributing to national energy sec...In today’s society, with the continuous growth of energy demand, Bohai Oilfield, as an important offshore oil resource base in China, is facing increasingly severe challenges while contributing to national energy security. In order to improve the quality of water injection in the oilfield and gradually achieve efficient and stable production, Bohai Oilfield has launched a water injection well pressure optimization project, focusing on improving the efficiency and quality of water injection in the water injection wells, in order to achieve the optimal water injection plan. In practical work, P Oilfield continues to promote the development of water injection well pressure optimization projects, emphasizing practical exploration and continuous optimization of work plans. However, during the project implementation process, there were some problems, one of which was that the statistics of cumulative injection volume were not scientific enough, resulting in a more comprehensive and accurate presentation of the actual results of pressure optimization work. In the context of continuous improvement work, after careful analysis and research, P Oilfield has decided to optimize the cumulative injection rate algorithm to guide the oilfield’s water injection work in a more refined way, ensuring sufficient and good water injection, and enhancing the oilfield’s production efficiency and comprehensive competitiveness.展开更多
The oil/water separation in a liquid-liquid cylindrical cyclone is experimentally studied in this article.The effects of the flow split-ratio and the flow rate on the oil/water separation performance are determined.Fr...The oil/water separation in a liquid-liquid cylindrical cyclone is experimentally studied in this article.The effects of the flow split-ratio and the flow rate on the oil/water separation performance are determined.From the experimental results,it is shown that with the increase of the flow split-ratio,the oil/water separation efficiency is enhanced at first,and an optimal flow split-ratio exists,beyond that optimal split-ratio,the watercut in the underflow keeps constant,while the oil content in the overflow begins to decrease.The process of the oil core structure formation and the phase distribution in the cyclone are determined by numerical simulations.Furthermore,the dependence of the separation efficiency on the Reynolds number and the flow split-ratio is investigated based on a dimensional analysis.A comparison between the predicted values and the experimental data shows a good agreement.展开更多
In recent years, graphene oxide(GO), prepared by the modified Hummers’ method, and its derivatives have become a focus of research owing to their outstanding physical and chemical properties and low cost. Drawing ins...In recent years, graphene oxide(GO), prepared by the modified Hummers’ method, and its derivatives have become a focus of research owing to their outstanding physical and chemical properties and low cost. Drawing inspiration from the mussel protein,a facile and environmentally-friendly method was employed to fabricate superhydrophobic/superoleophilic reduced graphene oxide(rGO) derivative. The preparation comprises two steps: coating GO nanosheets with polydopamine(PDA) and subsequent reaction with 1H,1H,2H,2H-perfluorodecanethiol. Due to the excellent adhesive ability of PDA, the resulting f PDA modified rGO nanosheets(rGO-f PDA) were firmly immobilized onto polyurethane(PU) sponge skeleton by a simple drop-coating method. The as-prepared rGO-f PDA functionalized sponge exhibited superhydrophobic behavior with a water contact angle of 162°±2°, high organic adsorption capacity, recyclability and stable oil/water separation behavior under different acidic/alkaline conditions. Due to its facile fabrication technique and outstanding properties, the superhydrophobic-superoleophilic PU-rGOf PDA sponge holds great promise as an oil adsorbent for cleaning up large-scale pollution of oil and organic solvents, and dehydrating crude oil.展开更多
The aggregates in sodium dedecylsulphate (SDS)/dimethylbenzene/water systems have been investigated using dissipative particles dynamic (DPD) simulation method. Through analyzing three dimensional structures of aggre...The aggregates in sodium dedecylsulphate (SDS)/dimethylbenzene/water systems have been investigated using dissipative particles dynamic (DPD) simulation method. Through analyzing three dimensional structures of aggregates, three simulated results are found. One is the phase separation, which is clearly observed by water density and the aggregates in the simulated cell; another is the water morphology in reverse micelle, which can be found through the isodensity slice of water including bound water, trapped water and bulky water; the third is about the water/oil interface, i.e., ionic surfactant molecules, SDS, prefer to exist in the interface between water and oil phase at the low concentration.展开更多
基金Financial support from the Science Fund for Creative Research Groups of the National Science Foundation of China (22021005)the National Natural Science Foundation of China (21776032)the Innovation Team of Dalian University of Technology (DUT2017TB01)。
文摘Tungsten (W) incorporated mobil-type eleven (MEL) zeolite membrane (referred to as W-MEL membrane) with high separation performance was firstly explored for the separation of oil/water mixtures under the influence of gravity.W-MEL membranes were grown on stainless steel (SS) meshes through in-situ hydrothermal growth method facilitated with (3-aminopropyl)triethoxysilane (APTES) modification of stainless steel meshes,which promote the heterogeneous nucleation and crystal growth of W-MEL zeolites onto the mesh surface.W-MEL membranes were grown on different mesh size supports to investigate the effect of mesh size on the separation performance of the membrane.The assynthesized W-MEL membrane supported on 500 mesh (25μm)(W-MEL-500) exhibit the hydrophilic nature with a water contact angle of 11.8°and delivers the best hexane/water mixture separation with a water flux and separation efficiency of 46247 L·m^(-2)·h^(-1)and 99.5%,respectively.The wettability of W-MEL membranes was manipulated from hydrophilic to hydrophobic nature by chemically modifying with the fluorine-free compounds (hexadecyltrimethoxysilane (HDTMS) and dodecyltrimethoxysilane(DDTMS)) to achieve efficient oil-permselective separation of heavy oils from water.Among the hydrophobically modified W-MEL membranes,W-MEL-500-HDTMS having a water contact angle of146.4°delivers the best separation performance for dichloromethane/water mixtures with a constant oil flux and separation efficiency of 61490 L·m^(-2)·h^(-1)and 99.2%,respectively along with the stability tested up to 20 cycles.Both W-MEL-500-HDTMS and W-MEL-500-DDTMS membranes also exhibit similar separation performances for the separation of heavy oil from sea water along with a 20-fold lower corrosion rate in comparison with the bare stainless-steel mesh,indicating their excellent stability in seawater.Compared to the reported zeolite membranes for oil/water separation,the as-synthesized and hydrophobically modified W-MEL membranes shows competitive separation performances in terms of flux and separation efficiency,demonstrating the good potentiality for oil/water separation.
基金the financial support from National Key Research & Development Program of China (2017B0602702)。
文摘In this paper, the superhydrophobic polyurethane sponge(SS-PU) was facilely fabricated by etching with Jones reagent to bind the nanoparticles of Ni-Co double layered oxides(LDOs) on the surface, and following modification with n-dodecyl mercaptan(DDT). This method provides a new strategy to fabricate superhydrophobic PU sponge with a water contact angle of 157° for absorbing oil with low cost and in large scale. It exhibits the strong absorption capacity and highly selective characteristic for various kinds of oils which can be recycled by simple squeezing. Besides, the as-prepared sponge can deal with the floating and underwater oils, indicating its application value in handling oil spills and domestic oily wastewater. The good self-cleaning ability shows the potential to clear the pollutants due to the ultralow adhesion to water. Especially, the most important point is that the superhydrophobic sponge can continuously and effectively separate the oil/water mixture against the condition of turbulent disturbance by using our designed device system, which exhibit its good superhydrophobicity, strong stability.Furthermore, the SS-PU still maintained stable absorption performance after 150 cycle tests without losing capacity obviously, showing excellent durability in long-term operation and significant potential as an efficient absorbent in large-scale dispose of oily water.
基金We gratefully acknowledge the financial support from National Key Research and Development Project,China(2019YFA0708700)the National Natural Science Foundation of China(52222403,52074333)the Innovation Fund Project for graduate students of China University of Petroleum(East China)(22CX04049A).
文摘The membrane method based on adaptive wettability shows great advantages in oil-water separation.At present,researches focus on the excellent application performance of the membrane material,while the quantitative analysis of interactions in oil-water separation is rarely recognized.Herein,we constructed an adaptable wettability membrane with multiple polymer networks by polydopamine(PDA)and mussel-inspired amphiphilic polymer.Based on the Owens three-probe liquid method,the surface energy of the modified membrane was verified to meet the adaptive wettability conditions,with surface energies(γ-8)of 147.6 mJ m^(−2)(superhydrophilic/underwater superoleophobic)and 49.87 mJ m^(−2)(superhydrophobic/superoleophobic),respectively.The adhesion or repulsion of the membrane to the oil phase under different conditions during the separation process was quantified by the chemical probe AFM technique.In addition,the oil-water selective separation mechanism was further analyzed in a simplified membrane microchannel model.The results show that the different wetting produces capillary additional pressure in opposite directions,resulting in different energies to be overcome when the oil or water passes through the microchannels,thus achieving selective separation.
基金the National Natural Science Foundation of China(No.21776319 and No.21476269).
文摘In this work, a simple method was carried out to successfully fabricate superoleophilic and superhydrophobic N-dodecyltrimethoxysilane@tungsten trioxide coated copper mesh. The as-fabricated copper mesh displayed prominent superoleophilicity and superhydrophobicity with a huge water contact angle about 154.39° and oil contact angle near 0° Moreover, the coated copper mesh showed high separation efficiency approximately 99.3%, and huge water flux about 9962.3 L·h^-1·m-2, which could be used to separate various organic solvents/ water mixtures. Furthermore, the coated copper mesh showed favorable stability that the separation efficiency remained above 90% after 10 separation cycles. Benefiting from the excellent photocatalytic degradation ability of tungsten trioxide, the coated copper mesh possessed the self-cleaning capacity. Therefore, the mesh contaminated with lubricating oil could regain superhydrophobic property, and this property of self-cleaning permitted that the fabricated copper mesh could be repeatedly used for oil and water separation.
文摘Studies on nonlinear behavior at oil/water interface membrane were performed. This system showed rhythmic oscillations and chaos of electrical potential in a given concentration domain. The nonlinear behavior response at the liquid membrane apparently resembled that of biological chemoreceptive membrane. The possibility of developing a new type of chemical sensor with the ability to simulate substance equilibrium in living organisms was suggested in the paper.
基金supported by the National Natural Science Foundation of China(21303232)the China Postdoctoral Science Foundation(2018M632610)
文摘It is of great necessity yet still a challenge to develop superwetting functional interfacial materials for simultaneously separating insoluble oil and degrading soluble dye pollutants in practical wastewater.In this work,a Ag-CuO heterostructure-decorated mesh was fabricated via facile alkali etchingcalcination and photoreduction approaches.The as-synthesized mesh with superhydrophilicity and underwater superoleophobicity displayed high separation efficiency(>99.998%)for diverse oil/water mixtures.Besides,it demonstrated more superior photocatalytic performance in dye degradation than those of bare CuO nanostructure-coated materials,which is primarily attributed to the intensive visible light harvesting and efficient electron-holes separation occurred on noble metal-semiconductor heterostructures.Furthermore,on account of the tenacity of Cu substrate as well as enhanced structural stability,this binary composite-decorated mesh exhibited highly reliable durability and robustness after 10 cycles of photocatalytic degradation tests,and even being ultrasonic worn for 30 min.More importantly,our developed mesh was capable of in situ catalytic degrading water-soluble organic dyes during oil/water separation under visible light irradiation.Therefore,such a dexterous and feasible strategy may afford a new route to construct bifunctional and predurable materials for actual sewage purification.
基金Supported by the National Natural Science Foundation of China(21776319)
文摘Nowadays, oil spills have led to a serious environmental crisis of the world. To deal with this problem, inspired from super-hydrophobic lotus leaf, this study fabricated super-hydrophobic and super-lipophilic functionalized graphene oxide/polyurethane(FGP) sponge by a simple and inexpensive dip coating method. The resulting FGP sponge was characterized by infrared spectroscopy, X-ray diffraction, scanning electron microscopy and water contact angle. The results expressed that FGP sponge exhibited a similar surface structure to that of a lotus leaf, and possessed the super-hydrophobic characteristic with the water contact angle(WAC) of 152°±1°. The absorption capacity and reusability were also investigated. It can be seen that, the FGP sponge can remove a wide range of oils and organic solvents from water with good absorption capacities(up to 35 times of its own mass). Significantly, after 10 cycles the absorption capacity of the oils and organic solvents was higher than 90%for the reused FGP sponge, demonstrating the good reusability of the FGP sponge. Therefore, this study probably provided a simple way to remove the pollutions of oil spills and toxic organism from water.
文摘Polyethylene glycol(PEG) membranes with different molecular mass cut-offs were used to treat oil/water emulsion, and the effects of experimental conditions including pressure, temperature and different opera- ting modes on permeate flux and removal rate of chemical oxygen demand (COD_ Cr) were studied. The results show that the permeate flux of ultrafiltration membrane is influenced by pressure and temperature; practical pressure is chosen to be 0.30.7MPa for the PEG with molecular mass cut-offs of 8000 and 0.71.0 MPa for the PEG with molecular mass cut-offs of 2500; and the practical temperature is chosen to be 2532℃. Different operating modes of ultrafiltration also influence the permeate flux and removal rate of COD_ Cr. The ultrafiltration membrane of intermittent cross-flow operating mode is easier to be influenced by blocky polarization and contamination than that of sequential cross-flow operating mode. Removal rate of COD_ Cr in intermittent cross-flow and sequential cross-flow condition can be maintained at about 93%.
文摘Alkaline-surfactant-polymer (ASP) flooding using sodium hydroxide as the alkali component to enhance oil recovery in Daqing Oilfield, northeast China has been successful, but there are new problems in the treatment of produced crude. The alkali added forms stable water-in-crude oil emulsion, hence de-emulsification process is necessary to separate oil and water. The problems in enhanced oil recovery with ASP flooding were investigated in laboratory by using fractions of Daqing crude oil. The oil was separated into aliphatics, aromatics, resin and asphaltene fractions. These fractions were then mixed with an additive-free jet fuel to form model oils. The interfacial properties, such as interfacial tension and interracial pressure of the systems were also measured, which together with the molecular parameters of the fractions were all used to investigate the problems in the enhanced oil recovery. In our work, it was found that sodium hydroxide solution reacts with the acidic hydrogen in the fractions of crude oil and forms soap-like interfacially active components, which accumulate at the crude oil-water interface.
文摘Produced water from an oil extraction site in South Kuwait was sampled after primary oil – water separation had been carried out. The produced water was filtered through a mixture of activated charcoal and esterified cellulosic material gained from spent coffee grounds as a tertiary adsorption treatment. The earth-alkaline metal ions and heavy metals were separated from the de-oiled produced water by addition of either sodium or potassium hydroxide in the presence of carbon dioxide or by direct addition of solid sodium carbonate. The resulting filtrate gave salt of industrial purity upon selective crystallization on evaporation.
文摘Produced water (PW) is the largest waste stream in the oil and gas industry. Water remains trapped for millions of years in the reservoir with oil and gas. When a hydrocarbon reservoir is infiltrated by a production well, the produced fluids commonly contain water. The understanding of this water’s constituents and volumes is vital for the sustainable continuity of production operations, as PW has a number of negative impacts on the infrastructure integrity of the operation. On the other hand, PW can be an alternative source of irrigation water as well as of industrial salt. Interestingly, both the quantity as well as the quality of PW do not remain constant but can vary, both progressively and erratically, even over short periods of time. This paper discusses such a situation of variable PW in an oil and gas operation in the State of Kuwait.
文摘Oil-water separation for produced water (PW) originating from an oil extraction site in South Kuwait was carried out using bleached, esterified cellulosic material from used coffee grounds. Thereafter, earth-alkaline metal ions, specifically calcium ions, of the de-oiled PW were removed by precipitation with sodium carbonate to give access to pure sodium chloride as industrial salt from the remaining PW. While the purity of the precipitated calcium carbonate (CaCO3) depends on the precipitation conditions, CaCO3 of up to 95.48% purity can be obtained, which makes it a salable product. The precipitation of CaCO3 decreases the amount of calcium ions in PW from 11,300 ppm to 84 ppm.
基金This work was financially funded by the National Natural Science Foundation of China(Nos.22205247 and 21988102).
文摘In recent years,numerous studies have been reported for oil/water separation,such as superoleophilic materials for oil absorption and underwater superoleophobic membranes for continuous separation.However,for the recovery of oil slick pollution on near-shore ocean surface caused by various reasons,large area and fast availability of used materials are needed to be considered.Herein,we report an efficient and environmentally friendly method to fast process nylon mesh by surface diffuse atmospheric plasma(SDAP)for large-area oil/water separation.Nylon mesh is funcionalized by atmospheric plasma to generate micro/nano composite structures on the surface,resulting in superhydrophilicity and underwater superoleophobicity within only seconds.The pre-wetted modified nylon mesh can achieve high efficiency(>99.9%)and circulating water flux(~30,000 L·m^(-2)·h^(-1)),with high intrusion pressure(~3 kPa)and universality in oil/water separation.Regular plasma unconditionally generated in the atmosphere with the merit of efficiently functionalizing surface has the potential of large-area materials treatment.This study might take one step further for large-area industrial oily wastewater recovery and even oil slicks collection in near-shore water bodies.
基金supported by the National Natural Science Foundation of China(Grant No.51473070).
文摘Because of the increasing amount of oily wastewater produced each day,it is important to develop superhydrophilic/underwater superoleophobic oil/water separation membranes with ultrahigh flux and high separation efficiency.In this paper,a superhydrophilic/underwater superoleophobic N-isopropylacrylamide-coated stainless steel mesh was prepared through a simple and convenient graft polymerization approach.The obtained mesh was able to separate oil/water mixtures only by gravity.In addition,the mesh showed high-efficiency separation ability(99.2%)and ultrahigh flux(235239 L·m^(−2)·h^(−1)).Importantly,due to the complex cross-linked bilayer structure,the prepared mesh exhibited good recycling performance and chemical stability in highly saline,alkaline and acidic environments.
基金supported by the College of Petroleum Engineering and Geosciences,King Fahd University of Petroleum and Minerals.
文摘We report the use of CaTiO_(3):Pr^(3+)multiband persistent luminescent nanoparticles,which can simultaneously emit red(610 nm),near-infrared(893 nm),and short-wave infrared(1040 nm)photoluminescence and persistent luminescence,as the tracer nanoagents for water tracer sensing.By using a spectrofluorometer,an Si charge-coupled device(CCD)camera and an InGaAs array camera as the detection tools,we evaluated the sensing capabilities of the three emission bands of CaTiO_(3):Pr^(3+)nanoparticles in brine water solutions and crude oil/brine water emulsions in both photoluminescence mode and persistent luminescence mode.Among these different detection combinations,the persistent luminescence-based Si CCD camera imaging exhibits the best sensing performance with the detection limits being at a single-digit ppb level for the 610 and 893 nm bands and about 100–200 ppb for the 1040 nm band in both water solutions and crude oil/water emulsions,while the photoluminescencebased Si CCD camera imaging has a much higher detection limit of~10 ppm in water solutions and of~200 ppm in oil/water emulsions.The persistent luminescence-based InGaAs array camera imaging to the 1040 nm band has the worst performance with the detection limits higher than 200 ppm for both solutions.The sensing performances of the spectrofluorometer to photoluminescence signals and persistent luminescence signals in the two solutions are about the same,with the detection limits being around 100–200 ppm.
文摘The comparative effectiveness of remediating water polluted with crude oil, using environment-friendly bacteria (Pseudomonas aeruginosa) and fungi (Aspergillus niger) were investigated. The samples were separately treated with Aspergillus niger and Pseudomonas aeruginosa. The bioremediation kinetic efficiency for these systems was studied. At the end of the bioremediation periods, the oil and grease content of the samples decreased from 47.0 mg/L in the untreated sample to 7.0 mg/L after 20 days when inoculated with bacteria while the sample inoculated with fungi decreased to 10.0 mg/L. Post analysis when inoculated with bacteria showed a fall in the value of the biological oxygen demand (BOD) from 73.84 mg/L to 33.28 mg/L after 20 days, while, the fungi inoculated sample showed a reduction from 73.84 mg/L to 38.48 mg/L. The biodegradation process with the bacteria was consistent with the pseudo-first-order model with a rate constant of 0.0891 day<sup>-1</sup>, while the biodegradation process with the fungi was consistent with the first order reaction model with a rate constant of 0.422 day<sup>-1</sup>. The degree of degradation after the 20<sup>th</sup> day of inoculation with Pseudomonas aeruginosa was 85.11%, while with Aspergillus niger was 78.72%. Thus, the results obtained showed that, Pseudomonas aeruginosa performed better than Aspergillus niger. The bioremediation data with fungi fitted the first-order model, while that of the bacteria fitted the pseudo-first-order model. Therefore, the data obtained in this study could be applied in the design of a bioremediation system for potential application to remediation of crude oil polluted water.
文摘In today’s society, with the continuous growth of energy demand, Bohai Oilfield, as an important offshore oil resource base in China, is facing increasingly severe challenges while contributing to national energy security. In order to improve the quality of water injection in the oilfield and gradually achieve efficient and stable production, Bohai Oilfield has launched a water injection well pressure optimization project, focusing on improving the efficiency and quality of water injection in the water injection wells, in order to achieve the optimal water injection plan. In practical work, P Oilfield continues to promote the development of water injection well pressure optimization projects, emphasizing practical exploration and continuous optimization of work plans. However, during the project implementation process, there were some problems, one of which was that the statistics of cumulative injection volume were not scientific enough, resulting in a more comprehensive and accurate presentation of the actual results of pressure optimization work. In the context of continuous improvement work, after careful analysis and research, P Oilfield has decided to optimize the cumulative injection rate algorithm to guide the oilfield’s water injection work in a more refined way, ensuring sufficient and good water injection, and enhancing the oilfield’s production efficiency and comprehensive competitiveness.
基金supported by the Knowledge Innovation Program of the Chinese Academy of Sciences(Grant No.KJCX1-YW-21)
文摘The oil/water separation in a liquid-liquid cylindrical cyclone is experimentally studied in this article.The effects of the flow split-ratio and the flow rate on the oil/water separation performance are determined.From the experimental results,it is shown that with the increase of the flow split-ratio,the oil/water separation efficiency is enhanced at first,and an optimal flow split-ratio exists,beyond that optimal split-ratio,the watercut in the underflow keeps constant,while the oil content in the overflow begins to decrease.The process of the oil core structure formation and the phase distribution in the cyclone are determined by numerical simulations.Furthermore,the dependence of the separation efficiency on the Reynolds number and the flow split-ratio is investigated based on a dimensional analysis.A comparison between the predicted values and the experimental data shows a good agreement.
基金supported by the National Natural Science Foundation of China(Grant Nos.51701240&41206063)Key Research and Development Program of Shandong Province(Grant No.2017GGX20123)Fundamental Research Funds for the Central Universities(Grant Nos.19CX05001A,16CX05011A&17CX02063)
文摘In recent years, graphene oxide(GO), prepared by the modified Hummers’ method, and its derivatives have become a focus of research owing to their outstanding physical and chemical properties and low cost. Drawing inspiration from the mussel protein,a facile and environmentally-friendly method was employed to fabricate superhydrophobic/superoleophilic reduced graphene oxide(rGO) derivative. The preparation comprises two steps: coating GO nanosheets with polydopamine(PDA) and subsequent reaction with 1H,1H,2H,2H-perfluorodecanethiol. Due to the excellent adhesive ability of PDA, the resulting f PDA modified rGO nanosheets(rGO-f PDA) were firmly immobilized onto polyurethane(PU) sponge skeleton by a simple drop-coating method. The as-prepared rGO-f PDA functionalized sponge exhibited superhydrophobic behavior with a water contact angle of 162°±2°, high organic adsorption capacity, recyclability and stable oil/water separation behavior under different acidic/alkaline conditions. Due to its facile fabrication technique and outstanding properties, the superhydrophobic-superoleophilic PU-rGOf PDA sponge holds great promise as an oil adsorbent for cleaning up large-scale pollution of oil and organic solvents, and dehydrating crude oil.
基金ProjectsupportedbytheNaturalScienceFoundationofShandongProvince (No .Y2 0 0 1B0 8)
文摘The aggregates in sodium dedecylsulphate (SDS)/dimethylbenzene/water systems have been investigated using dissipative particles dynamic (DPD) simulation method. Through analyzing three dimensional structures of aggregates, three simulated results are found. One is the phase separation, which is clearly observed by water density and the aggregates in the simulated cell; another is the water morphology in reverse micelle, which can be found through the isodensity slice of water including bound water, trapped water and bulky water; the third is about the water/oil interface, i.e., ionic surfactant molecules, SDS, prefer to exist in the interface between water and oil phase at the low concentration.