Separation of Oil Phase from Dilute Oil/Water Emulsion in Confined Space Apparatus

A miniature process for separating the oil phase from dilute oil/water emulsion is developed.This process applies a confined space apparatus,which is a thin flow channel made of two parallel plastic plates.The space between the two plates is rather narrow to improve the collisions between oil droplets and the plate surface.Oil droplets have an affinity for the plate surface and thus are captured,and then coalesce onto the surface.The droplet size distribution of the residual emulsion resulted from the separation process is remarkably changed.The oil layer on the plate weakens the further separation of oil droplets from the emulsion.Three types of plate materials,polypropylene(PP),polytetrafluoroethylene(PTFE) and nylon 66,were used.It is found that PP is the best in terms of the oil separation efficiency and nylon 66 is the poorest.The interaction between droplets in the emulsion and plate surface is indicated by the spreading coefficient of oil droplet on the plate in aqueous environment,and the influences of formed oil layer and plate material on the separation efficiency are discussed.

Treatment of oil/water emulsion by polyethylene glycol ultrafiltration membrane

Polyethylene glycol(PEG) membranes with different molecular mass cut-offs were used to treat oil/water emulsion, and the effects of experimental conditions including pressure, temperature and different opera- ting modes on permeate flux and removal rate of chemical oxygen demand (COD_ Cr) were studied. The results show that the permeate flux of ultrafiltration membrane is influenced by pressure and temperature; practical pressure is chosen to be 0.30.7MPa for the PEG with molecular mass cut-offs of 8000 and 0.71.0 MPa for the PEG with molecular mass cut-offs of 2500; and the practical temperature is chosen to be 2532℃. Different operating modes of ultrafiltration also influence the permeate flux and removal rate of COD_ Cr. The ultrafiltration membrane of intermittent cross-flow operating mode is easier to be influenced by blocky polarization and contamination than that of sequential cross-flow operating mode. Removal rate of COD_ Cr in intermittent cross-flow and sequential cross-flow condition can be maintained at about 93%.

Experimental investigation on using CO_(2)/H_(2)O emulsion with high water cut in enhanced oil recovery

CO_(2) emulsions used for EOR have received a lot of interest because of its good performance on CO_(2)mobility reduction.However,most of them have been focusing on the high quality CO_(2) emulsion(high CO_(2) fraction),while CO_(2) emulsion with high water cut has been rarely researched.In this paper,we carried out a comprehensive experimental study of using high water cut CO_(2)/H_(2)O emulsion for enhancing oil recovery.Firstly,a nonionic surfactant,alkyl glycosides(APG),was selected to stabilize CO_(2)/H_(2)O emulsion,and the corresponding morphology and stability were evaluated with a transparent PVT cell.Subsequently,plugging capacity and apparent viscosity of CO_(2)/H_(2)O emulsion were measured systematically by a sand pack displacement apparatus connected with a 1.95-m long capillary tube.Furthermore,a high water cut(40 vol%) CO_(2)/H_(2)O emulsion was selected for flooding experiments in a long sand pack and a core sample,and the oil recovery,the rate of oil recovery,and the pressure gradients were analyzed.The results indicated that APG had a good performance on emulsifying and stabilizing CO_(2) emulsion.An inversion from H_(2)O/CO_(2) emulsion to CO_(2)/H_(2)O emulsion with the increase in water cut was confirmed.CO_(2)/H_(2)O emulsions with lower water cuts presented higher apparent viscosity,while the optimal plugging capacity of CO_(2)/H_(2)O emulsion occurred at a certain water cut.Eventually,the displacement using CO_(2)/H_(2)O emulsion provided 18.98% and 13.36% additional oil recovery than that using pure CO_(2) in long sand pack and core tests,respectively.This work may provide guidelines for EOR using CO_(2) emulsions with high water cut.

Continuous monitoring of residual water content in boiling waterhydrocarbon emulsions during thermomechanical dehydration

Significant waste resources are generated in the form of water-oil emulsions.These emulsions cannot be effectively destroyed on an industrial scale by traditional methods that rely on the settling of the aqueous phase,and therefore,they accumulate in large quantities.Thermomechanical dehydration,based on the evaporation of the water phase,presents a promising process for recycling such waste.However,within the framework of thermomechanical dehydration,the issue of optimizing energy costs for heating raw materials and controlling the water content in the product arises.Standard methods of determining water content under the boiling conditions of highly stable water-hydrocarbon emulsions are characterized by low efficiency,as they require constant sampling and the involvement of additional equipment and personnel.Consequently,this presents a challenge in predicting and creating an automated thermomechanical dehydration process.Therefore,dynamic curves depicting changes in the water content of these emulsions,depending on the temperature of the boiling liquid,have been obtained.It is proposed to determine the rate of temperature increase(dT/dt)of the boiling emulsion for continuous,real-time monitoring of the residual water content and for recording the moment of complete dehydration.Achieving a boiling emulsion temperature of 130-170℃(or higher)and/or the rate of temperature increase from 3.0 to 5.5(or above)indicates the complete dehydration of the emulsion.The proposed method can be implemented in any industrial or laboratory-scale unit for thermomechanical dehydration without significant capital costs.It is based on the use of simple devices consisting of temperature sensors and a computing unit for determining the temperature and rate of heating.

Effects of Different Heavy Crude Oil Fractions on the Stability of Oil-in-water Emulsions —— Isolation of functional fractions from heavy crude oil and study of their properties

The functional fractions (acid, basic, amphoteric and neutral fractions) are isolated from the Liaohe Du-84 heavy crude oil and Shengli Gudao Kenxi heavy crude oil by ion-exchange chromatography, but the conventional fractions (saturates, aromatics, resins and asphaltenes) are also isolated from the heavy crude oil. These components have been characterized by spectroscopic methods (FT-IR), namely acid number, basic nitrogen number, ultimate analysis and molecular weight measurements using vapor pressure osmometry (VPO). The ion-exchange chromatography method based on separation by a functional group induces a little change on the nature of the crudes and reasonable mass balances can be easily obtained.

Red/NIR/SWIR multi-band persistent luminescent nanoparticles as ultrasensitive multi-channel tracers in water and crude oil/water emulsions

We report the use of CaTiO_(3):Pr^(3+)multiband persistent luminescent nanoparticles,which can simultaneously emit red(610 nm),near-infrared(893 nm),and short-wave infrared(1040 nm)photoluminescence and persistent luminescence,as the tracer nanoagents for water tracer sensing.By using a spectrofluorometer,an Si charge-coupled device(CCD)camera and an InGaAs array camera as the detection tools,we evaluated the sensing capabilities of the three emission bands of CaTiO_(3):Pr^(3+)nanoparticles in brine water solutions and crude oil/brine water emulsions in both photoluminescence mode and persistent luminescence mode.Among these different detection combinations,the persistent luminescence-based Si CCD camera imaging exhibits the best sensing performance with the detection limits being at a single-digit ppb level for the 610 and 893 nm bands and about 100–200 ppb for the 1040 nm band in both water solutions and crude oil/water emulsions,while the photoluminescencebased Si CCD camera imaging has a much higher detection limit of~10 ppm in water solutions and of~200 ppm in oil/water emulsions.The persistent luminescence-based InGaAs array camera imaging to the 1040 nm band has the worst performance with the detection limits higher than 200 ppm for both solutions.The sensing performances of the spectrofluorometer to photoluminescence signals and persistent luminescence signals in the two solutions are about the same,with the detection limits being around 100–200 ppm.

Experimental measurements of water content in crude oil emulsions by terahertz time-domain spectroscopy

We measured the water content （0.01% 0.25% w/w） in crude oil emulsions using terahertz time-domain spectroscopy （THz-TDS）. To improve the precision and range of the measurements, we used 1 and 10 mm thick quartz cells. The experiments were performed at 20 ℃ and the THz wave was transmitted vertically to the samples and detected on the other side. The experimental results suggest linear relation for the THz absorption coefficient and the water content of the crude oil emulsions in the observed range. The linear dependence facilitates high-precision measurements of the water content of crude oil. This suggests the potential of THz-TDS in determining the water concentration in crude oil and borehole fluid identification.

Hyperspectral remote sensing identification of marine oil emulsions based on the fusion of spatial and spectral features

Marine oil spill emulsions are difficult to recover,and the damage to the environment is not easy to eliminate.The use of remote sensing to accurately identify oil spill emulsions is highly important for the protection of marine environments.However,the spectrum of oil emulsions changes due to different water content.Hyperspectral remote sensing and deep learning can use spectral and spatial information to identify different types of oil emulsions.Nonetheless,hyperspectral data can also cause information redundancy,reducing classification accuracy and efficiency,and even overfitting in machine learning models.To address these problems,an oil emulsion deep-learning identification model with spatial-spectral feature fusion is established,and feature bands that can distinguish between crude oil,seawater,water-in-oil emulsion(WO),and oil-in-water emulsion(OW)are filtered based on a standard deviation threshold–mutual information method.Using oil spill airborne hyperspectral data,we conducted identification experiments on oil emulsions in different background waters and under different spatial and temporal conditions,analyzed the transferability of the model,and explored the effects of feature band selection and spectral resolution on the identification of oil emulsions.The results show the following.(1)The standard deviation–mutual information feature selection method is able to effectively extract feature bands that can distinguish between WO,OW,oil slick,and seawater.The number of bands was reduced from 224 to 134 after feature selection on the Airborne Visible Infrared Imaging Spectrometer(AVIRIS)data and from 126 to 100 on the S185 data.(2)With feature selection,the overall accuracy and Kappa of the identification results for the training area are 91.80%and 0.86,respectively,improved by 2.62%and 0.04,and the overall accuracy and Kappa of the identification results for the migration area are 86.53%and 0.80,respectively,improved by 3.45%and 0.05.(3)The oil emulsion identification model has a certain degree of transferability and can effectively identify oil spill emulsions for AVIRIS data at different times and locations,with an overall accuracy of more than 80%,Kappa coefficient of more than 0.7,and F1 score of 0.75 or more for each category.(4)As the spectral resolution decreasing,the model yields different degrees of misclassification for areas with a mixed distribution of oil slick and seawater or mixed distribution of WO and OW.Based on the above experimental results,we demonstrate that the oil emulsion identification model with spatial–spectral feature fusion achieves a high accuracy rate in identifying oil emulsion using airborne hyperspectral data,and can be applied to images under different spatial and temporal conditions.Furthermore,we also elucidate the impact of factors such as spectral resolution and background water bodies on the identification process.These findings provide new reference for future endeavors in automated marine oil spill detection.

Synthesis of a Novel Core-shell Type Acrylic-polyurethane Hybrid Emulsion Containing Siloxane and Fluorine as well as Water and the Oil Resistances of Cured Film

Siliconated polyurethane （Si-PU） was synthesized using isophorone diisocyanate （IPDI）, hydroxybutyl-terminated polydimethylsiloxane （PDMS）, polytetramethylene ether glycol （PTMG）, polypropylene glycol （PPG）, 1,6-hexanediol （HDO）, dimethylol propionic acid （DMPA） and triethylamine （TEA）. Based on butyl acrylate （BA）, 2, 2, 2-trifluoroethylmethacrylate （TFEMA） and Si-PU as a seed emulsion, a novel core-shell type acrylic-polyurethane hybrid emulsion, containing siloxane and fluorine （F-Si-PU）, was prepared by seeded emulsion polymerization. The contents of siloxane and fluorine were determined according to the feed ratio. Fourier transform infrared spectroscopy （FTIR） was used to identify the chain structures of Si-PU and F-Si-PU. Investigation of transmission electron microscopy （TEM） confirmed the core-shell structure of F-Si-PU emulsion. Measurement results of water contact angle and the swelling ratio in water and n-octane for cured film showed that the water and the oil resistances for F-Si-PU had been significantly improved at a suitable content of fluorine and siloxane.

Experimental investigation of the effects of various parameters on viscosity reduction of heavy crude by oil-water emulsion

The effects of water content, shear rate, temperature, and solid particle concentration on viscosity reduction （VR） caused by forming stable emulsions were investigated using Omani heavy crude oil. The viscosity of the crude oil was initially measured with respect to shear rates at different temperatures from 20 to 70℃. The crude oil exhibited a shear thinning behavior at all the temperatures. The strongest shear thinning was observed at 20℃. A non-ionic water soluble surfactant （Triton X-100） was used to form and stabilize crude oil emulsions. The emulsification process has significantly reduced the crude oil viscosity. The degree of VR was found to increase with an increase in water content and reach its maximum value at 50 % water content. The phase inversion from oil- oil emulsion occurred at 30 in-water emulsion to water-in- % water content. The results indicated that the VR was inversely proportional to temperature and concentration of silica nanoparticles. For water-in-oil emulsions, VR increased with shear rate and eventually reached a plateau at a shear rate of around 350 s^-1. This was attributed to the thinning behavior of the continuous phase. The VR of oil-in-water emulsions remained almost constant as the shear rate increased due to the Newtonian behavior of water, the continuous phase.

Fouling-resistant Composite Membranes for Separation of Oil-in-water Microemulsions

Fouling-resistant ceramic-supported polymer composite membranes were developed for removal of oil-in-water （O/W） mieroemulsions. The composite membranes were featured with an asymmetric three-layer structure, i.e., a porous ceramic membrane substrate, a polyvinylidene fluoride （PVDF） ultrafiltration sub-layer, and a polyamide/polyvinyl alcohol （PVA） composite thin top-layer. The PVDF polymer was east onto the tubular porous ceramic membranes with an immersion precipitation method, and the polyamide/PVA composite thin top-layer was fabricated with an inteffaeial polymerization method. The effects of the sub-layer composition and the recipe in the inteffaeial polymerization for fabricating the top-layer on the structure and performance of composite membranes were systematically investigated. The prepared composite membranes showed a good performance for treating the O/W microemulsions with a mean diameter of about 2.41μm. At the operating pressure of 0.4MPa, the hydraulic permeability remained steadily about 190L·m^-2·h^-1, the oil concentration in the permeate was less than 1.6mg·L^-1, and the oil rejection coefficient was always higher than 98.5% throughout the operation from the beginning.

Effects of Volume Ratios of Water Phase to Oily Phase on Morphology and Releasing Performance of Emulsion Electrospun Fibers

Emulsion electrospinning as a novel process in spinning core-sheath fibers shows a promising potential in drug release control. The volume ratio of water phase to oily phase is one of the critical parameters in forming core-sheath fibers. In this study, water phase was presented by hydrophilic tetracycline hydrochloride and oily phase by hydrophobic poly （E-caprolactone） （PCL）. The effects of volume ratios of water phase to oily phase on fiber morphology and in vitro drug release were investigated. Scanning electron microscopy （ SEM ）, transmission electron microscopy （ TEM）, and eonfoeal laser scanning microscopy（CLSM） were used to observe the morphology, core.sheath structure of the fibers and drug loading in the fibers, respectively. Samples of three different volume ratios of water phase to oily phase, 1： 25, 1：15, and 1：10, were prepared with the same concentration of drug solution. Experiment results showed that, with an increase in the volume ratios of water phase to oily phase, the fiber diameter increased and diameter distribution scattered. The drug entrapment efficiency of the fibers reduces with the increase in volume ratios, L e. , from 73.48 % in the ratio of 1 ： 25, 62.23 % in 1 ： 15, down to 45.63 % in 1：10. In vitro release tests showed that a higher volume ratio of water phase to oily phase would lead to a lower release rate resulted from thicker fiber sheath.

Coalescence separation of oil water emulsion on amphiphobic fluorocarbon polymer and silica nanoparticles coated fiber-bed coalescer

Discharging untreated oily wastewater into the environment disrupts the ecological balance,which is a global problem that requires urgent solutions.Superhydrophilic and superoleophilic fibrous medium(FM)effectively separated oil–water emulsion as it was hydrophobic underwater.But its separation efficiencies(SEs)first increased to 98.9%,then dropped to 97.6%in 10 min because of oil-fouling.To tackle this problem,FM deposited with 0%–10%silica nanoparticle(NPsFMs),then coated by fluorocarbon polymer(X-[CH_(2)CH_(2)O]nCH_(2)CH_(2)O-Y-NH-COOCH_(2)C4F9)(FCNPs FMs),was used to enhance its roughness and regulate its initial wettability to improve the anti-fouling property.FCFM and FCNPs FMs were hydrophobic and oleophobic in air and oleophobic underwater.Their water contact angles,oil contact angles and oil contact angles were 115.3°–121.1°,128.8°–136.5°,and 131.6°–136.7°,respectively,meeting the requirement of 90°–140°for coalescence separation.FCNPs FM-5 had the best separation performance with a constant value of 99.8%in 10 min,while that of FCNPs FM-10 slightly decreased to 99.5%.Theoretical released droplet(TRD)diameter,calculated by the square root of the product of pore radius and fiber diameter,was used for the evaluation of coalescence performance.Analyzed by two ideal models,TRD diameter and fiber diameter showed a parabola type relationship,proving that the separation efficiency was a collaborative work of wettability,pore size and fiber diameter.Also,it explained the SEs reduction from FCNPs FM-5 to FCNPs FM-10 was revelent to the three parameters.Moreover,FCNPsFMs effectively separated emulsions stabilized by cationic surfactant CTAB(SEs:97.3%–98.4%)and anionic surfactant SDBS(SEs:91.3%–93.4%).But they had an adverse effect on nonionic surfactant Tween-80 emulsion separation(SEs:94.0%–71.76%).Emulsions made by diverse oils can be effectively separated:octane(SEs:99.4%–100%),rapeseed oil(SEs:97.3%–98.8%),and diesel(SEs:95.2%–97.0%).These findings provide new insights for designing novel materials for oil–water separation by coalescence mechanism.

Electrostatic Enhancement of Coalescence of Oil Droplets(in Nanometer Scale) in Water Emulsion

Oil droplets in nanometer scale which are dispersed in water cannot be separated easily. An attractive technique is carried out by electrical phenomena to demulsify oil in water emulsion. In this research, non-uniform electric field or dielectrophoresis （DEP） is applied to remove sunflower oil （which is dispersed in the water）. Effectsof temperature, time and voltage （using AC-electric field） were considered to get the highest DEP-force （Fdi） and the best results. The oil particles sizes with average of approximately 76 nm have been shown using a ZetaSizer Nano ZS, Model ZEN 1600 （Malvem Instrument Ltd.）. The maximum separation efficiency of 85% is obtained at the optimum temperature of 38 ℃ and voltage of 3000 V.

Investigation into the effect of silica nanoparticles on the rheological characteristics of water-in-heavy oil emulsions

The effect of silica nanoparticles on the rheological characteristics of water-in-heavy oil emulsions has been investigated.Enhanced oil recovery methods for heavy oil production(most especially,thermal fluid injection)usually result in the formation of water-in-oil(W/O)emulsion.In reality,the emulsion produced also contains some fine solid mineral particles such as silica,which,depending on its quantity,may alter the viscosity and/or rheological properties of the fluid.A series of binary-component emulsions were separately prepared by dispersing silica nanoparticles[phase fraction,βs,=0.5%–5.75%(wt/v)]in heavy oil(S/O suspension)and by dispersing water[water cut,θw=10%–53%(v/v)]in heavy oil(W/O emulsion).Ternary-component emulsions comprising heavy oil,water droplets and suspended silica nanoparticles(S/W/O)were also prepared with similar ranges ofθw andβs.The viscosity was measured at different shear rates(5.1–1021.4 s-1)and temperatures(30–70°C).Both binary-component and ternary-component emulsion systems were observed to exhibit nonNewtonian shear thinning behaviour.The viscosity of the heavy oil and W/O emulsions increased in the presence of silica nanoparticles.The effect was,however,less signifi cant belowβs=2%(wt/v).Moreover,a generalized correlation has been proposed to predict the viscosity of both binary-component and ternary-component emulsions.

Measurement of water holdup in oil-in-water emulsions in wellbores using microwave resonance sensor

In this study,we propose a new method for water holdup measurement of oil-in-water emulsions with a microwave resonance sensor(MRS).The angle and length of the electrode plate are optimized by HFSS simulation software.Using a vector network analyzer(VNA),a static calibration experiment is conducted,and the resonant frequency distribution of oil-in-water emulsions is analyzed within an 80%–100%water holdup range.In addition,we observe and analyze the micron-sized oil bubble structure in the emulsifi ed state with an optical microscope.On this basis,a dynamic experiment of oil-in-water emulsions with high water cut and low velocity in a vertical upward pipe is conducted.S_(21) response curves of the MRS are obtained by the VNA under diff erent working conditions in real time.Finally,we analyze the relationship between the resonant frequency and water cut.Experimental results show that the MRS has an average resolution of 0.096%water cut for high water cut oil-in-water emulsions within the frequency range of 2.2–2.8 GHz.

Effects of Different Heavy Crude Oil Fractions on the Stability of Oil-in-water Emulsions—the film properties of heavy crude functional components and water system

A series of π-A isotherms are drawn to study the film properties of the components with Langmuir-Blodgett technique. The effects of the aromaticity of spread solvents and pH value on the air/water film formed by the components are investigated. Acid fraction and asphaltene can form stable two-dimensional insoluble films on an air/water surface. The surface film pressure of acid fraction and asphaltene is higher and more stable than that of the other fractions. The surface film pressure of the fraction increases evidently under the basic condition (pH=12). The results show that the interfacial activity of acid fraction and asphaltene is superior to that of the other fractions and the basic condition is favorable to the stability of the O/W emulsion.

Characterization of water-in-crude oil emulsions in oil spill response

The formation of water in crude oil emulsions occurs when crude oils are spilled into sea. The water in crude oil emulsions significantly change the properties of the spilled crude oils and in turn influence the choices made relating to oil spill countermeasures. The water in crude oil emulsions were characterized using various techniques in this study. The environmental scanning electron microscopy observation of water droplets in the emulsions is also presented. It is a powerful tool in emulsion observations.

Impact of sesame lignan on physical and oxidative stability of flaxseed oil-in-water emulsion

Recent studies have shown that the highly susceptibility to oxidation ofα-linolenic acid(ALA)enriched emulsion delivery system was harmful for human health which limited their incorporation into functional food.Impacts of natural sesamol(SOH)and sesamin(SES)on stability of flaxseed oil-in-water emulsion were investigated.Results showed that SOH indicated higher antioxidant activity and significantly prolonged the time of emulsion oil-off by retarding oil droplet aggregation in a dose dependent manner throughout storage.Moreover,SOH showed substantial extended lag phase of lipid oxidation products,especially for secondary oxidation products(thiobarbituric acid-reactive substances,TBARS),with a maximum reduction of 70%with 800 M dosage.The antioxidative efficiency of SOH might relate to its strong ability of scavenging free radical and chelate transition metal.Furthermore,SOH significantly enhanced interfacial barrier property and reduced permeation rate of peroxyl radical across emulsion interface by hydrogen bonds between sugar groups of saponin molecules and SOH.However,no obvious change in barrier property of emulsion was observed in SES.SOH improved physicochemical property of flaxseed oil-in-water emulsion with higher antioxidant activity and stronger interfacial barrier property,so that it could be serve as plant-based antioxidant in oil-in-water emulsion delivery system.

Modeling and Simulation of High Power Ultrasonic Process in Preparation of Stable Oil-in-Water Emulsion

The aims of this research are to study application of high power ultrasound in preparation of stable oil-in-water emulsion. The effect of pH, ionic strength, pectin, Guar gum, lecithin, egg yolk, and xanthan gum as well as the time of sonication, temperature and viscosity of oil-water mixture on the specific surface area and size of droplets, and creaming index of the emulsion samples was investigated. The experimental data were analyzed with Taguchi method and optimum conditions were determined. In addition, an adaptive neuro-fuzzy inference system (ANFIS) was employed to modeling and categorizes the properties of the resulted emulsion. The results showed that increasing sonication time narrowed the range of droplets size distribution. Pectin and xanthan enhanced the stability of emulsion, although they had different impacts on the emulsion stability when used individually or together. Guar gum improved the viscosity of the continuous phase. Emulsions stabilized by egg yolk were found to be stable to droplet flocculation at pH 3 and at relatively low salt concentrations.