Preparation and Thermo-Responsive Properties of Poly(Oligo(Ethylene Glycol)Methacrylate)Copolymers with Hydroxy-Terminated Side Chain

Thermo-responsive random copolymers,poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-(ethylene glycol)methyl ether methacrylate)(P(EO_(2)-co-EO_(4/5)))and poly(2-(2-methoxyethoxy)ethoxyethyl methacrylate-co-ethylene glycol methacrylate(P(EO2-co-EG4/5))are synthesized via atom transfer radical polymerization(ATRP).The successful synthesis and the narrow polydispersity index(PDI)of two copolymers are indicated by 1H nuclear magnetic resonance(1H-NMR)and gel permeation chromatography(GPC)analyses.The transition behaviors of polymers in the aqueous solution are demonstrated by changes in turbidity and particle sizes.The transition behavior of P(EO2-co-EG4/5)is found to be milder than that of P(EO2-co-EO4/5).Moreover,the presence of hydrogen bonds without thermo-responsive properties established by hydroxyl groups in the end-side chain of P(EO_(2)-co-EG_(4/5))hinders the dehydration at the transition temperature(TT).Attenuated total reflection Fourier transform infrared spectrometry(ATR-FTIR)analysis along with contact angle measurements reveals that both P(EO_(2)-co-EO_(4/5))and P(EO_(2)-co-EG_(4/5))films undergo phase transitions from hydrophilicity to hydrophobicity above TT.By examining the swelling and collapse behaviors of the polymer films during phase transitions,it can be concluded that the end hydroxyl groups may establish hydrogen bonds with neighboring ether groups within the films,which remain intact throughout the phase transition process due to their strong bonding interactions.This leads to an increase in steric hindrance within swollen films thereby impeding dehydration processes and inducing hysteresis during phase transitions.

Oligo(dT)亲和层析介质的载量比较和机制分析

针对Oligo(d T)亲和层析介质的吸附性能,以poly(A)为模型分子,考察了4种Oligo(d T)亲和层析介质的静态吸附平衡、吸附动力学和动态结合载量(DBC),探讨了载量影响相关机制。结果表明,4种介质的合适吸附条件均为0.6 mol·L-1Na Cl、p H=6~7;Monomix d T20静态吸附容量最大,且poly(A)能扩散至介质微球深层孔内,而Poros Oligo(d T)25、Praesto Jetted (d T)25和Nano Gel d T20等3种介质中poly(A)均主要为表层吸附、静态吸附容量稍低;对于DBC,Nano Gel d T20和Monomix d T20的10%穿透的DBC较高,而Poros Oligo (d T)25和Praesto Jetted (d T)25相对略低。经分析,影响载量的主要因素包含基质种类、微球孔径、配基密度、间隔臂和配基长度等。对于基质种类,聚苯乙烯基质可能孔道结构较为特别。对于微球孔径,应针对不同大小的m RNA分子定制不同孔径的微球,以平衡传质阻力与可及吸附表面积之间的矛盾,从而增大DBC。

B-COPNA resin formation from ethylene tar light fractions:Process development and mechanical exploration by molecular simulation

An efficient utilization strategy of ethylene tar(ET),the main by-product of the ethylene cracking unit,is urgently required to meet demands for modern petrochemical industry.On the other hand,condensed polynuclear aromatic resin of moderate condensation degree(B-COPNA)is a widely used carbon material due to its superb processability,the production of which is,however,seriously limited by the high cost of raw materials.Under such context,an interesting strategy was proposed in this study for producing B-COPNA resin using crosslinked light fractions of ethylene tar(ETLF,boiling point<260℃)facilitated by molecular simulation.1,4-Benzenedimethanol(PXG)was first selected as the crosslinking agent according to the findings of molecular simulation.The effects of operating conditions,including reactions temperature,crosslinking agent,and catalyst content on the softening point and yield of B-COPNA resin products were then investigated to optimize the process.The reaction mechanism of resin production was studied by analyzing the molecular structure and transition state of ETLF and crosslinking agents.It was shown that PXG exhibited a superior capacity of withdrawing electrons and a higher electrophilic reactivity than other crosslinking agents.In addition to the highest yield and greatest heat properties,PXG-prepared resin contained the most condensed aromatics.The corresponding optimized conditions of resin preparation were 180℃,1:1.9(PXG:ETLF),and 3%(mass)of catalyst content with a resin yield of 78.57%.It was the electrophilic substitution reaction that occurred between the ETLF and crosslinking agent molecules that were responsible for the resin formation,according to the experimental characterization and molecular simulation.Hence,it was confirmed that the proposed strategy and demonstrated process can achieve a clean and high value-added utilization of ETLF via B-COPNA resin preparation,bringing huge economic value to the current petrochemical industry.

Reaction pathways and selectivity in the chemo-catalytic conversion of cellulose and its derivatives to ethylene glycol:A review

Biomass-to-ethylene glycol is an effective means to achieve high-value utilisation of cellulose but is hindered by low conversion efficiency and poor catalyst activity and stability.Glucose and cellobiose are derivatives of cellulose conversion to ethylene glycol,and it is found that studying the reaction process of both can help to understand the reaction mechanism of cellulose.It is desirable to develop a reusable,highly active catalyst to convert cellulose into ethylene glycol.This ideal catalyst might have one or more active sites described the conversion steps above.Here,we discuss the catalyst development of celluloseto-ethylene glycol,including tungsten,tin,lanthanide,and other transition metal catalysts,and special attention is given to the reaction mechanism and kinetics for preparing ethylene glycol from cellulose,and the economic advantages of biomass-to-ethylene glycol are briefly introduced.The insights given in this review will facilitate further development of efficient catalysts,for addressing the global energy crisis and climate change related to the use of fossil fuels.

Boosting kinetic separation of ethylene and ethane on microporous materials via crystal size control

The adsorptive separation of C_(2)H_(4)and C_(2)H_(6),as an alternative to distillation units consuming high energy,is a promising yet challenging research.The great similarity in the molecular size of C_(2)H_(4)and C_(2)H_(6)brings challenges to the regulation of adsorbents to realize efficient dynamic separation.Herein,we reported the enhancement of the kinetic separation of C_(2)H_(4)/C_(2)H_(6)by controlling the crystal size of ZnAtzPO_(4)(Atz=3-amino-1,2,4-triazole)to amplify the diffusion difference of C_(2)H_(4)and C_(2)H_(6).Through adjusting the synthesis temperature,reactant concentration,and ligands/metal ions molar ratio,ZnAtzPO4 crystals with different sizes were obtained.Both single-component kinetic adsorption tests and binary-component dynamic breakthrough experiments confirmed the enhancement of the dynamic separation of C_(2)H_(4)/C_(2)H_(6)with the increase in the crystal size of ZnAtzPO_(4).The separation selectivity of C_(2)H_(4)/C_(2)H_(6)increased from 1.3 to 98.5 with the increase in the crystal size of ZnAtzPO_(4).This work demonstrated the role of morphology and size control of adsorbent crystals in the improvement of the C_(2)H_(4)/C_(2)H_(6)kinetic separation performance.

Unraveling the incompatibility mechanism of ethylene carbonate-based electrolytes in sodium metal anodes

Ethylene carbonate(EC)is widely used in lithium-ion batteries due to its optimal overall performance with satisfactory conductivity,relatively stable solid electrolyte interphase(SEI),and wide electrochemical window.EC is also the most widely used electrolyte solvent in sodium ion batteries.However,compared to lithium metal,sodium metal(Na)shows higher activity and reacts violently with EC-based electrolyte(NaPF_(6)as solute),which leads to the failure of sodium metal batteries(SMBs).Herein,we reveal the electrochemical instability mechanism of EC on sodium metal battery,and find that the com-bination of EC and NaPF_(6) is electrically reduced in sodium metal anode during charging,resulting in the reduction of the first coulombic efficiency,and the continuous consumption of electrolyte leads to the cell failure.To address the above issues,an additive modified linear carbonate-based electrolyte is provided as a substitute for EC based electrolytes.Specifically,ethyl methyl carbonate(EMC)and dimethyl carbon-ate(DMC)as solvents and fluoroethylene carbonate(FEC)as SEI-forming additive have been identified as the optimal solvent for NaFP_(6)based electrolyte and used in Na_(4)Fe_(3)(PO_(4))_(2)(P_(2)O_(7))/Na batteries.The batter-ies exhibit excellent capacity retention rate of about 80%over 1000 cycles at a cut-off voltage of 4.3 V.

Ca_(2)MnO_(4)-layered perovskite modified by NaNO_(3)for chemical-looping oxidative dehydrogenation of ethane to ethylene

Chemical-looping oxidative dehydrogenation(CL-ODH)is a process designed for the conversion of alkanes into olefins through cyclic redox reactions,eliminating the need for gaseous O_(2).In this work,we investigated the use of Ca_(2)MnO_(4)-layered perovskites modified with NaNO_(3) dopants,serving as redox catalysts(also known as oxygen carriers),for the CL-ODH of ethane within a temperature range of 700-780℃.Our findings revealed that the incorporation of NaNO_(3) as a modifier significantly-nhanced the selectivity for-thylene generation from Ca_(2)MnO_(4).At 750℃and a gas hourly space velocity of 1300 h^(-1),we achieved an-thane conversion up to 68.17%,accompanied by a corresponding-thylene yield of 57.39%.X-ray photoelectron spectroscopy analysis unveiled that the doping NaNO_(3) onto Ca_(2)MnO_(4) not only played a role in reducing the oxidation state of Mn ions but also increased the lattice oxygen content of the redox catalyst.Furthermore,formation of NaNO_(3) shell on the surface of Ca_(2)MnO_(4) led to a reduction in the concentration of manganese sites and modulated the oxygen-releasing behavior in a step-wise manner.This modulation contributed significantly to the enhanced selectivity for ethylene of the NaNO_(3)-doped Ca_(2)MnO_(4) catalyst.These findings provide compelling evidence for the potential of Ca_(2)MnO_(4)-layered perovskites as promising redox catalysts in the context of CL-ODH reactions.

Synthesis of Branched Polyethylene via Bulky α-Diimine Nickel(II)-Catalyzed Ethylene Chain-Walking Polymerization

The catalysis of olefin polymerization through the chain-walking process is a subject of great interest. In this contribution, the successful synthesis of a Brookhart-type unsymmetrical α-diimine nickel catalyst Ni, which contains both dibenzhydryl and phenyl groups, was determined by X-ray crystallography. The compound has a pseudo-tetrahedral geometry at the Ni center, showing pseudo-C2-symmetry. Upon activation with modified methylaluminoxane (MMAO), Ni1 exhibits high catalytic activity up to 1.02 × 107 g PE (mol Ni h)−1 toward ethylene polymerization, enabling the synthesis of high molecular weight branched polyethylene. The molecular weights and branching densities could be tuned over a very wide range. The polymerization results indicated the possibility of precise microstructure control, depending on the polymerization temperature. The branching densities were decreased with increasing the polymerization temperature.

Novel sandwich structured glass fiber Cloth/Poly(ethylene oxide)-MXene composite electrolyte

Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.

Polyvinyl Acetate and Vinyl Acetate-Ethylene Hybrid Adhesive: Synthesis, Characterization, and Properties

The goal is to develop a hybrid IPN network of polyvinyl acetate (PVAc) and ethylene-vinyl acetate (VAE). In this research work, the vinyl acetate (VAc)/ VAE hybrid emulsion and polyvinyl acetate emulsion (PVAc) were effectively synthesized. Emulsions with various characteristics have been developed by adjusting the weight ratios between the vinyl acetate monomer and the VAE component. The impacts on the mechanical, thermal, and physical properties of the films were investigated using tests for pencil hardness, tensile shear strength, pH, contact angle measurement, differential scanning calorimetry (DSC), and viscosity. When 5.0 weight percent VAE was added, the tensile shear strength in dry conditions decreased by 18.75% after a 24-hour bonding period, the heat resistance decreased by 26.29% (as per WATT 91) and the tensile shear strength decreased by approximately 36.52% in wet conditions (per EN 204). The pristine sample’s results were also confirmed by the contact angle test. The interpenetrating network (IPN) formation in hybrid PVAc emulsion as primary bonds does not directly attach to PVAc and VAE chains. The addition of VAE reduced the mechanical properties (at dry conditions) and heat resistance as per WATT 91. Contact angle analysis demonstrated that PVAc adhesives containing VAE had increased water resistance when compared to conventional PVA stabilised PVAc homopolymer-based adhesives. When compared to virgin PVAc Homo, the water resistance of the PVAc emulsion polymerization was enhanced by the addition of VAE.

Oligo-FISH涂染揭示柚粗线期1号染色体的结构及配对

【目的】深化柑橘减数分裂粗线期染色体结构组成和配对分析。【方法】首次利用柑橘染色体全长特异寡核苷酸荧光原位杂交(oligo-fluorescence in situ hybridization,oligo-FISH)涂染探针,精准示踪鉴定沙田柚粗线期1号染色体的结构特征,比较其与有丝分裂间期细胞核、有丝分裂前中期和中期染色体的结构差异,并揭示粗线期全长染色体的同源配对。【结果】观测到同源配对的全长粗线期与有丝分裂中期较大染色质结构差异。经测定,柚粗线期1号染色体平均全长、长臂长、短臂长和臂比分别为中期的13.93倍、16.54倍、10.44倍和1.54倍,表现出更高FISH信号分辨率。检测到柚粗线期1号染色体着丝粒附近约3.01 Mb的探针信号缺失区。【结论】首次实现柑橘特定全长粗线期染色体的跟踪研究,为深入开展其结构和配对遗传利用的精准研究提供了新方法。

Effect of acid density of HZSM-5 on the oligomerization of ethylene in FCC dry gas

The oligomerization of ethylene in FCC dry gas over HZSM-5 catalyst with different Si/A12 ratios was studied. The effect of acid density of catalyst on the oligomerization of ethylene was discussed. By increasing the acid density of catalyst, ethylene conversion showed a linear increase, while the yields of olefins decreased when the acid density of catalyst exceeded 0.14mmolNH3/g owing to a promotion of hydrogen transfer reaction. Through comparing the average distance between acid sites on catalyst with kinetic diameters of olefins, it was found that the dimerization of ethylene was not restrained by the sparse distribution of acid sites, while the hydrogen transfer reaction of C3 and C4 olefins was limited. On these bases, a conclusion is proposed that the dimerization of ethylene proceeded via Eley-Rideal mechanism, while the hydrogen transfer reaction of C3 and C4 olefins followed the Langmuir-Hinshelwood mechanism.

Ethylene Oligomerization Promoted by Nickel Complexeswith 8-Iminoquinoline Derivatives

A series of 8-iminoquinoline derivatives nickel complexes were synthesized to proceed high activity in ethylene oligomerization.

Nickel Complexes Bearing Bidentate SchifF Base as Ethylene Oligomerization Catalysts

Several nickel complexes [N,N]NiBr_2, in which [N,N] indicates bidentatenitrogen-containing ligands (1: [N,N]=N-(2,6-diisopropylphenyl)pyridine-2-carboxaldimine(C_(18)H_(22)N_2); 2: N-(2,6-diisopropylphenyl)-6-methylpyridine-2-carboxaldimine (C_(19)H_(24)N_2);3: N-(2,4,6-trimethylphenyl)pyridine-2-carboxaldimine(C_(15)H_(16)N_2); 4:N-(2,4,6-trimethylphenyl)-6-methylpyridine-2-carboxaldimine (C_(16)H_(18)-N_2) were synthesized.Some of the nickel complexes exhibit high activity for ethylene oligomerizatiori in the presence ofan organoaluminum activator. The main factor affecting the activity and the structure of oligomersis the steric effect of substituents on [N,N] ligands. Methylaluminoxane (MAO) -activated catalystsshowed higher activities and produced oligomers with higher molecular weight than Et_2AlCl-activatedones. The oligomerization in toluene rather than hexane results in much higher activity, and theoligomers produced in toluene have relatively high molecular weight. With activation of MAO orEt_2AlCl, the [N,N]NiBr_2 system tended to produce highly branched oligomers with low α-olefincontent, but the α-olefin content could be increased by changing the reaction conditions.

Dealuminated ZSM-5 Zeolite Catalyst for Ethylene Oligomerization to Liquid Fuels

Ethylene oligomerization using ZSM-5 zeolite was investigated to study the role of Bronsted acid sites in the formation of higher hydrocarbons. The oligomerization of olefins, dependent on the acidity of ZSM-5 zeolite, is an important step in the conversion of natural gas to liquid fuels. The framework Si/Al ratio reflects the number of potential acid sites and the acid strength of the ZSM-5 catalyst. ZSM-5 with the mole ratio SiO2/Al2O3 equal to 30 was dealuminated for different periods of time according to the acidic ion-exchange method to produce ZSM-5 with various Si/Al ratios. The FT-IR analysis revealed that the integrated framework aluminum band, non-framework aluminum band, and silanol groups areas of the ZSM-5 zeolites decreased after being dealuminated. The performance of the dealuminated zeolite was tested for ethylene oligomerization. The results demonstrated that the dealumination of ZSM-5 led to higher ethylene conversion, but the gasoline selectivity was reduced compared to the performance of a ZSM-5 zeolite. The characterization results revealed the amount of aluminum in the zeolitic framework, the crystallinity of the ZSM-5 zeolite, and the Si/Al ratio affected the formation of Bronsted acid sites. The number of the Bronsted acid sites on the catalyst active sites is important in the olefin conversion to liquid hydrocarbons.

Oligomerization and Polymerization of Ethylene Initiated by a Novel Ni(Ⅱ)-Based Acetyliminopyridine Complexes as Single-Site Catalysts

Novel Ni（II）-based acetyliminopyridine complexes 1b, 2b, 3b （1-3b）, which are synthesized from ligands 1a, 2a, 3a （1-3a） and [NiCl2（DME）], are suitable precursors for the catalysts that are necessary for ethylene oligomerization and polymerization reactions, activated by methylaluminoxane （MAO）. The MAO-treated 1-3b presents an active catalytic center, which may oligomerize and polymerize ethylene to produce linear α-olefins and polyethylene, respectively. The molecular weight distributions of oligomers that are obtained are in good agreement with the Schulz-Flory rules for oligomers〉C4. The activity of 3b-MAO complex is 6.3×10^7 g/（molNi.h） at 50 ℃. The activities and molecular weight distributions of oligomers show significant reliance on the structures of catalyst precursors.

SYNTHESIS AND POLYMERIZATION OF OLIGO (OXYETHYLENE) MACROMONOMER

This paper reports the synthesis of methoxyoligo (oxyethylene) methacrylate (MEO_n , n is the repeating unit number of (CH_2CH_2O) in the macromonomer), and its polymerization in different solvents. MEO_n is prepared through such two independent reactions as (1) anionic polymerization of oxirane initiated by potassium alkoxide and (2) end-capping of methoxy oligo(oxyethylene) by methacrylic group. The n value can be conveniently controlled over the range of 5 ～ 30 by varying the molar ratio of oxirane to initiator and the molecular weight distribution of MEO_n be narrowed by increasing reaction time only in step (1). MEO_n thus obtained shows a rapid polymerization in water and benzene respectively, and both give water-soluble polymers as long as suitable conditions are used.

Ethylene Oligomerization by (dppe)MCl_2 [M = Fe(II), Co(II),Ni(II)] Complexes/EAO

The catalytic properties of a series of (dppe) MCl2 [M = Fe(II), Co(II), Ni(II)] in combination with EAO (ethylaluminoxane) for ethylene oligomerization have been investigated. Treatment of the bidentate phosphine metal complexes with EAO in toluene generated in situ active catalysts which catalyze oligomerizaton of ethylene to low-carbon olefins. The effects of reaction temperature, ratios of n(Al) : n(M) and reaction periods on catalytic activity and product distribution have been studied. The activity of cobalt complex with EAO at 200C was 4021 g/g(Co)h, and the selectivity of C4-10 olefins is 95.5%.

Synthesis and Characterization of {2-Formyl-6-[1-(2,4,6-trimethylphenyl)]-4- chlorophenoxy}_2Ni and Its Ethylene Oligomerization

The title nickel complex （C34H3oCl2N2NiO4, Mr = 660.21） has been synthesized and its crystal structure was determined by single-crystal X-ray structure analysis. It crystallizes in the monoclinic system, space group P21/n with a = 11.026（8）, b = 11.491（8）, c = 12.119（9） A°, β=91.328（13）°, Z= 2, V= 1535.0（19） ,A°^3, Dc = 1.428 g/cm^3, F（000） = 684 andμ（MoKa） = 0.848 mm^-1 The structure was refined to R = 0.0544 for 1813 observed reflections with I 〉 2σ（I） and wR =0.0867 for 3132 unique reflections. The molecule of the complex is high symmetrical. Ni（Ⅱ） atom is located in the symmetric center and coordinated to two phenolic oxygen and two imino nitrogen atoms, forming two six-membered rings. Upon activation with methylaluminoxane （MAO）, it is active for ethylene oligomerization.