Origin of Felsic Microgranitoid Enclaves in Granite in Zhangjiakou District,China:Implication for Process and Lifespan of Granitic Magma Chambers

Sparse felsic microgranitoid enclaves(FMEs)in the Shangshuiquan granite of the Zhangjiakou district,the north margin of the North China Craton,are fine-grained,dark-colored and exhibit subangular to subspherical shapes.They share similar mineral assemblages,chemical compositions,and zircon Hf isotope compositions to the host granite.New zircon U-Pb geochronology reveals that the FMEs crystallized at 156-153 Ma,while the Shangshuiquan granite formed at ca.146 Ma.The FEMs are,therefore,10 to 7 Ma older than the host granite.Combined with petrological evidence,we suggest that the FMEs are fragments of rapidly crystalized magmas,which were captured by the younger Shangshuiquan magma.Magmas of the FMEs and Shangshuiquan granite originated from the same reservoir.The Shangshuiquan granite is the result of small batches of magma being built up incrementally,and the FMEs belong to the earlier batches of magma.The lifespan of the Shangshuiquan magma reservoir exceeds 10 Ma.FMEs derived from cogenetic fragments have the potential to offer critical information about the formation process and timescale of granitic plutons.

A new tube chamber system for evaluation of anterior chamber pressure during phacoemulsification tested in porcine eyes

AIM:To measure the optimal anterior chamber pressure(ACP)for safe phacoemulsification using a new tube chamber system with internal pressure measurement function in the porcine eye.METHODS:The 20-gauge and 21-gauge straight tips with yellow and orange sleeves,respectively,were covered by a test chamber combined with a pressure sensor for measuring ACP.This was measured for 20s from 10s after starting aspiration in the linear mode using vacuum levels of 200 and 150 mm Hg with a 20-gauge tip,and 300 and 250 mm Hg with a 21-gauge tip.Using a porcine eye,a pressure sensor fixed with a 0.9 mm corneal incision measured ACP.For the posterior capsule contact assay,porcine eyes were treated as described above,and the ultrasonic needle tip was held at the height of the iris and aspirated for 30s in linear mode at a vacuum of 200 and 150 mm Hg for the 20-gauge tip,and 300 and 250 mm Hg for the 21-gauge tip.The bottle height at which the posterior capsule accidentally contacted the ultrasonic tip was recorded,and the estimated ACP was calculated.RESULTS:The internal pressure of the new tube chamber system and ACP from the porcine eye closely matched proportional changes at vacuum levels of 200 and 150 mm Hg with 20-gauge tips.Similarly,proportional changes at vacuum levels of 300 and 250 mm Hg with the 21-gauge tip were nearly equal.The bottle height at which the posterior capsule contacted with the tip and estimated ACP were 57.5±12.6 cm(20.2±7.9 mm Hg)at 200 mm Hg with a 20-gauge tip,35.0±10.0 cm(16.6±6.3 mm Hg)at 150 mm Hg with a 20-gauge tip,47.5±12.6 cm(18.7±8.7 mm Hg)at 300 mm Hg with a 21-gauge tip,and 32.5±5.0 cm(15.7±3.5 mm Hg)at 250 mm Hg with a 21-gauge tip.CONCLUSION:A comprehensive understanding of this chamber system’s characteristics and usage can resolve anterior chamber instability caused by changing preoperative settings on the phaco machine.

Topographic factors associated with anterior chamber angle narrowing in patients with keratoconus

AIM:To identify topographic determinants of the anterior chamber angle(ACA)in patients with keratoconus(KCN).METHODS:Four hundred and ten eyes of 294 patients with KCN were recruited for this study.First,complete ocular examinations were performed for all patients,including visual acuity measurement,refraction,and slit-lamp biomicroscopy.Then,all participants underwent corneal imaging by the Oculus Pentacam HR.RESULTS:The mean age of the participants was 32.40±8.52y(15-60y)and 69.5%of them were male.The mean ACA was 38.47°±5.75°(range:14.40°to 56.50°)in the whole sample,38.24°±6.00°in males,and 38.98°±5.11°in females(P=0.447).The mean ACA was significantly different among different groups of cone morphology,as patients with nipple cones showed the lowest mean ACA.Moreover,there were statistically significant differences in the mean ACA among different groups of cone locations,with patients having central cones exhibiting the lowest mean ACA(P<0.001).Anterior and posterior Q values were significantly,directly correlated with ACA(anterior Q:r=0.122,P=0.014,posterior Q:r=0.192,P<0.001).CONCLUSION:This study provides critical insights into the risk factors for ACA narrowing in KCN patients,which is essential for planning intraocular surgeries.Patients with nipple and central cones exhibited the most significant ACA narrowing.Additionally,more negative Q-values are associated with increased ACA narrowing,highlighting the need for targeted diagnostic and therapeutic strategies.

Impacts of ozone on the biomass and yield of rice in open top chambers

The impacts of different 03 concentration on the biomass and yield of rice were studied by using OTC-1 open-top chambers. Experimental treatments included the activated charcoal-filtered air. (CFA), 50 nl/L (CF50), 100 nl/L ( CF100) and 200 nl/L (CF200) concentrations of O-3. The O-3 treatments significantly decreased the total biomass per plant. The. elevated O-3 exposure resulted in a more decrease in the root growth than in the shoot growth. Assessments of yield characteristics at the final harvest revealed an O-3-induced decrease in the number of grains per plant, resulting from fewer ears per plant, fewer grains per ear and more unfilled grains per ear. The 1000 grain dry weight and the harvest index (HI) were not changed significantly under 50 nl/L or 100 nl/L O-3 exposure, but reduced by 17.0% and 4.8% by 200nl/L O-3 treatment, respectively. Compared to the CFA treatment, CF50, CF100 and CF200 treatments caused a 8.2%, 26.1%, 49.1% decrease of the grain yield per plant, and a 14.2%, 31.7%, 51.7% decrease of the total biomass per plant, respectively. Linear regression showed that the 7h - daily mean O-3 concentration exposure for 3 months ( July-September) and AOT40 ( cunulative exposure accumulation over threshold 40 nl/L) were well correlated with the relative grain yield. A yield loss of 10% was estimated to be at 46.9 nl/L O-3 for 7h-daily mean O-3 concentration exposure or at 12930nl/(L(.)h) O-3 for AOT40.

Biophysical warming patterns of an open-top chamber and its short-term influence on a Phragmites wetland ecosystem in China

Passive-warming, open-top chambers(OTCs) are widely applied for studying the effects of future climate warming on coastal wetlands. In this study, a set of six OTCs were established at a Phragmites wetland located in the Yellow River Delta of Dongying City, China. With data collected through online transmission and in-situ sensors, the attributes and patterns of realized OTCs warming are demonstrated.The authors also quantified the preliminary influence of experimental chamber warming on plant traits.OTCs produced an elevated average air temperature of 0.8°C(relative to controls) during the growing season(June to October) of 2018, and soil temperatures actually decreased by 0.54°C at a depth of 5 cm and 0.46°C at a depth of 30 cm in the OTCs. Variations in diel patterns of warming depend greatly on the heat sources of incoming radiation in the daytime versus soil heat flux at night. Warming effects were often larger during instantaneous analyses and influenced OTCs air temperatures from-2.5°C to 8.3°C dependent on various meteorological conditions at any given time, ranging from cooling influences from vertical heat exchange and vegetation to radiation-associated warming. Night-time temperature depressions in the OTCs were due to the low turbulence inside OTCs and changes in surface soilatmosphere heat transfer. Plant shoot density, basal diameter, and biomass of Phragmites decreased by23.2%, 6.3%, and 34.0%, respectively, under experimental warming versus controls, and plant height increased by 4.3%, reflecting less carbon allocation to stem structures as plants in the OTCs experienced simultaneous wind buffering. While these passive-warming OTCs created the desired warming effects both to the atmosphere and soils, pest damages on the plant leaves and lodging within the OTCs were extensive and serious, creating the need to consider control options for these chambers and the replicated OTCs studies underway in other Chinese Phragmites marshes(Panjin and Yancheng).

Autologous nerve segment-bridging regeneration chambers for the repair of sciatic nerve defects

Proximal and distal nerve defects exhibit chemotactic growth over certain distances. Our previous studies demonstrated that Schwann cells survive in autologous nerve segments that are bridged by regeneration chambers and secrete various bioactive substances. However, more data are required to determine the required length of regeneration chambers for chemotaxis and nutrition of neural regeneration, as well as the length of repaired nerve defects to replace the effect of autologous nerve grafting. In the present study, sciatic nerve defects of 12, 16, 20 mm were repaired using a regeneration chamber of 6, 8, and 10 mm in length respectively. These were bridged with autologous nerve segments. Results showed that the bridging of two 6-mm long regeneration chambers to repair a 12-mm nerve defect exhibited similar effects to autologous nerve grafting.

Cannabinoids Increase Mechanosensitivity of Trigeminal Ganglion Neurons Innervating the Inner Walls of Rat Anterior Chambers via Activation of TRPA1

Our previous study found that some trigeminal ganglion（TG） nerve endings in the inner walls of rat anterior chambers were mechanosensitive, and transient receptor potential ankyrin 1（TRPA1） was an essential mechanosensitive channel in the membrane. To address the effect of cannabinoids on the mechanosensitive TG nerve endings in the inner walls of anterior chambers of rat eye, we investigated the effect of the（R）-（＋）-WIN55, 212-2 mesylate salt（WIN）, a synthetic cannabinoid on their cell bodies in vitro. Rat TG neurons innervating the inner walls of the anterior chambers were labeled by 1,1＇-dilinoleyl-3,3,3＇,3＇-tetramethylindocarbocyanine, 4-chlorobenzenesulfona（FAST Di I）. Whole cell patch clamp was performed to record the currents induced by drugs and mechanical stimulation. Mechanical stimulation was applied to the neurons by buffer ejection. WIN evoked inward currents via TRPA1 activation in FAST Di I-labeled TG neurons. WIN enhanced mechanosensitive currents via TRPA1 activation in FAST Di I-labeled TG neurons. Our results indicate that cannabinoids can enhance the mechanosensitivity of TG endings in the inner walls of anterior chambers of rat eye via TRPA1 activation.

Failure mechanism of pump chambers and their optimized design in deep mining at Qishan Coal Mine

Pump chambers, normally used as dominant structures in mining engineering to insure the safety and production of un-derground coal mines, become generally deformed under conditions of deep mining. Given the geology and engineering condition of Qishan Coal Mine in Xuzhou, the failure characteristics of pump chambers at the –1000 m level show that the main cause can be attributed to the spatial effect induced by intersectional chambers, where one pump is constructed per well. We developed an opti-mized design of the pump room, in which the pump wells in the traditional design are integrated into one compounding well. We suggest that the new design can limit the spatial effect of intersectional chambers during construction given our relevant numerical simulation. The new design is able to simplify the structure of the pump chamber and reduce the amount of excavation required. Based on a bolt-mesh-anchor with a rigid gap coupling supporting technology, the stability of pump chamber can be improved greatly.

Research on the "three shells" cooperative support technology of large-section chambers in deep mines

The"three shells"cooperative support technology was proposed herein according to both the large deformation of the rock surrounding large-section chambers in deep mines and the precarious stability of the support structures therein.The development range of the plastic zone in the surrounding rock was controlled by a stress shell to reduce the difficulty of controlling the surrounding rock.Additionally,the residual strength of the rock mass in the plastic zone and the self-bearing capacity of the surrounding rock were improved by a reinforced load-bearing shell.Furthermore,a passive load-bearing shell could restore the triaxial stress state of the surrounding rock on the free surface,reduce the influence of the external environment on the surrounding rock,and reinforce the surrounding rock with the strength of the shell.Reasonable layouts of large-section chambers were determined by analyzing the control effect of the stress shell on the surrounding rock under three kinds of in situ stress fields.The orthogonal test method was applied to reveal the influences of different support parameters in the reinforced loadbearing shell and passive load-bearing shell on the surrounding rock stability.The surrounding rock control effect of the"three shells"collaborative support technology was analyzed through numerical simulation and field monitoring.The results show that the maximum displacement between the roof and floor of the coal preparation chamber in the Xinjulong coal mine was approximately 48 mm,and the maximum displacement between its two sides was approximately 65 mm,indicating that the technology proposed herein could meet the long-term control requirements of the surrounding rock stability for large-section chambers in deep mines.

Destabilization analysis of overlapping underground chambers induced by blasting vibration with catastrophe theory

According to the main characters of overlapping underground chambers, the roof (floor) of two adjacent underground chambers is simplified to the mechanical model that is the beam with build-in ends. And vibration load due to blasting is simplified to harmonic wave. The catastrophic model of double cusp for underground chambers destabilization induced by blasting vibration has been established under the circumstances of considering deadweight of the beam, and the condition of destabilization has been worked out. The critical safety thickness of the roof (floor) of underground chambers has been confirmed according to the destabilization condition. The influence of amplitude and frequency of blasting vibration load on the critical safety thickness has been analyzed, and the quantitative relation between velocity, frequency of blasting vibration and critical safety thickness has been determined. Research results show that the destabilization of underground chambers is not only dependent on the amplitude and frequency of blasting vibration load, but also related to deadweight load and intrinsic attribute. It is accordant to testing results and some related latest research results of blasting seismic effect. With increasing amplitude, the critical safety thickness of underground chambers decreases gradually. And the possibility of underground chambers destabilization increases. When the frequency of blasting vibration is equal to or very close to the frequency of beam, resonance effect will take place in the system. Then the critical safety thickness will turn to zero, underground chambers will be damaged severely, and its loading capacity will lose on the whole.

Effects of Inlet/Outlet Ducts on Acoustic Attenuation Characteristics of Circular Expansion Chambers

The effect of coaxial, offset and extended inlet/outlet on the acoustic attenuation characteristics of circular expansion chambers are studied by the three-dimensional finite dement method. The numerical results of transmission loss are compared with experiment results to verify the necessary of using three-dimensional methods. Maps of acoustic pressure level distribution inside of chambers and inlet/outlet ducts are given at a frequency to demonstrate the difference of acoustic wave propagation behavior caused by locations of inlet/outlet ducts. For the chambers of the same length, the chamber with extended inlet/outlet duct has higher attenuation ability than coaxial and offset inlet/outlet duct over middle frequencies.

Chemoattractive capacity of different lengths of nerve fragments bridging regeneration chambers for the repair of sciatic nerve defects

A preliminary study by our research group showed that 6-mm-long regeneration chamber bridging is equivalent to autologous nerve transplantation for the repair of 12-mm nerve defects. In this study, we compared the efficacy of different lengths （6, 8, 10 mm） of nerve fragments bridging 6-mm regeneration chambers for the repair of 12-mm-long nerve defects. At 16 weeks after the regeneration chamber was implanted, the number, diameter and myelin sheath thickness of the regenerated nerve fibers, as well as the conduction velocity of the sciatic nerve and gastrocnemius muscle wet weight ratio, were similar to that observed with autologous nerve transplantation. Our results demonstrate that 6-, 8-and 10-mm-long nerve fragments bridging 6-mm regeneration chambers effectively repair 12-mm-long nerve defects. Because the chemoattractive capacity is not affected by the length of the nerve fragment, we suggest adopting 6-mm-long nerve fragments for the repair of peripheral nerve defects.

LET Monitoring Using Liquid Ionization Chambers

Relative biological effectiveness (RBE) is an important quantity in planning particle beam cancer therapy. In general, the RBE describes the biological effectiveness of a given primary beam with respect to a reference photon irradiation. RBE varies not only for different primary beams but also with depth in the target for a given beam modality. It is not a quantity that easily lends itself to measurements or computation as it depends on many biological and physical quantities. Numerous experiments in vitro using various cell lines and irradiation modalities have shown that a general relationship between RBE and the physical quantity Linear Energy Transfer (LET) exists. Several groups have proposed including LET in the radiation therapy treatment planning instead of the more complicated and elusive RBE. It has been shown that LET is an important quantity to consider in treating radio-resistant tumors. The concept of LET painting has been proposed with the goal of improving tumor control probability (TCP) for hypoxic tumors by focusing high LET radiation on the hypoxic region of the tumor while restricting the surrounding normal tissue to low LET radiation. In order to properly incorporate LET in clinical treatment, it is important to be able to experimentally measure and verify LET distribution. We propose a novel method for measuring LET using a dual chamber methodology exploiting the difference in the observed recombination between air filled ionization chambers (IC) and liquid filled ionization chambers (LIC). The resulting difference in the measured signals will be used to directly extract the relative LET of an actual treatment beam in real time. This paper describes our initial studies of this method, presents preliminary results, and discusses further improvements toward a practical real-time LET measuring device.

Comparison of different plasma chambers in microwave ion source for the intense neutron tube

The microwave absorption efficiency, which is relevant to magnet field and its distribution, is a major parameter of the microwave ion source (MWIS) for the intense neutron tube. Based on previous work, the relations between microwave absorption efficiency and plasma chamber structure and thickness of the microwave introduction window are studied. The microwave absorption efficiency reaches to 100% when plasma chamber is 100mm long and the window thickness is 30mm. The microwave absorption efficiency as a function of pressure is also presented.

Converging Parallel Plate Flow Chambers for Studies on the Effect of the Spatial Gradient of Wall Shear Stress on Endothelial Cells

Many in vitro studies focus on effects of wall shear stress (WSS) and wall shear stress gradient (WSSG) on endothelial cells, which are linked to the initiation and progression of atherosclerosis in the arterial system. Limitation in available flow chambers with a constant WSSG in the testing region makes it difficult to quantify cellular responses to WSSG. The current study proposes and characterizes a type of converging parallel plate flow chamber (PPFC) featuring a constant gradient of WSS. A simple formula was derived for the curvature of side walls, which relates WSSG to flow rate (Q), height of the PPFC (h), length of the convergent section (L), its widths at the entrance (w0) and exit (w1). CFD simulation of flow in the chamber is carried out. Constant WSSG is observed in most regions of the top and bottom plates except those in close proximity of side walls. A change in Q or h induces equally proportional changes in WSS and WSSG whereas an alteration in the ratio between w0 and w1 results in a more significant change in WSSG than that in WSS. The current design makes possible an easy quantification of WSSG on endothelial cells in the flow chamber.

Fundamental Laws of Physics and Calculation of Heat Transfer in Combustion Chambers of Gas-Turbine Plants

The laws of heat radiation from black body, the laws of Stefan-Boltzmann, Planck, and Wien are fundamental laws of physics. All in all, a little more than 30 fundamental laws of physics, studied by pupils and students worldwide were disclosed. Scientific disclosure of fundamental laws influences mainly power technology, fuel and energy resources saving. In the late XIX century the laws of heat radiation from gas volumes and the laws of Makarov were disclosed. Since the radiation laws from blackbody are fundamental laws of physics, then the laws of heat radiation from gas volumes are fundamental laws of physics. Effect of using laws of heat radiation from gas volumes on fuel saving, reduction of development pressure on the environment in many countries of the world is shown. Calculation results from heat transfer in combustion chamber of gas-turbine plant are described. The torch in a combustion chamber is modeled by cylindrical gas volumes. Fluxes data from the torch and convective fluxes of cooling air are confirmed by measuring data from chamber-wall temperature.

Sensitivity of the area method with mono isotopic fission chambers to reactivity changes in subcritical nuclear reactors

High-level waste is an important safety issue in the development of nuclear power.A proposed solution is the transmutation of waste in fast reactors.The exclusion of the risk of supercriticality by using subcritical reactors is currently under development.Controlling the subcriticality level in such reactors presents difficulties.A problem is posed by the so-called space effect observed when using in reactors many neutron detectors in different locations of the core and reflector.Reactivity obtained from measure-ments,for example,by the Sjo¨strand method,differs by nonnegligible values.Numerical corrections can partially improve this situation.The use of a monoisotopic fission chamber set,designed for a given reactor,when each chamber is intended for a specific position in the system,can improve the situation.A question arises about the sensitivity of the results to reactivity changes.This issue is analyzed by computer simulation for possible fissionable and fissile nuclides for the total range of control rod insertion,changes in reactor fuel enrichment,and fuel temperature.The tested sensitivity was satisfactory at most levels from several dozen to several hundred pcm.A case study was conducted using the VENUS-F core model.

New Materials for Vacuum Chambers in High Energy Physics

Vacuum chambers must fulfil ultra-high vacuum requirements while withstanding thermo-mechanical loads. This is particularly true in high energy particle accelerator where interactions of particles with matter may induce thermal load, material activation, background… The choice of the material of the vacuum chamber is crucial for the final application. Metals such as stainless steel, copper and aluminium are usually used. Even with outstanding mechanical and physical properties, beryllium is used for very specific applications because of its cost and toxicity.Ceramics such as alumina are usually used for fast magnet vacuum chambers. With the next generation of high energy physics accelerator generation such as CLIC and TLEP, the problematic of high cyclic thermal load induced by synchrotron radiation is raised. This paper aims at defining some figures of merit of different materials with respect to several load scenarios and presents briefly their vacuum compatibility.

Absorbed Dose to Water Rate in a Cyberknife VSI System Reference Field Using Ionization Chambers and Gafchromic Films

This work investigated the absorbed dose to water rate under reference conditions in a Cyberknife VSI system using radiochromic films EBT3 and MD-V3 and three ionization chambers: an Exradin A12 and two FC65P Welh&ouml;fer Scanditronix with different serial numbers. The correction factor,, was studied using a Varian iX linac and the Cyberknife system. The measurements in the Varian iX were performed in a 10 × 10 cm2 field, 10 cm depth in liquid water at 90 cm and 70 cm SSD and in a 5.4 × 5.4 cm2 field, 10 cm depth at 70 cm SSD to simulate the Cyberknife conditions. In the Cyberknife system, measurements were performed using ionization chambers and both film types at 70 cm SSD and 10 cm depth in its 6 cm diameter reference field. The results indicate that ?is independent of the dosimeters and the evaluation methods. Maximum differences of 0.22% - 0.55% (combined uncertainties of 1.22% - 1.98%, k = 1) are obtained on ?using Varian iX, whereas discrepancies of 2.08% - 2.09% (combined uncertainties of 1.87% - 2.13%, k = 1) are observed using the Cyberknife system. Given the agreement between detectors and the combined standard uncertainties, the data from Varian iX could be considered the most accurate and consequently a weighted average factor of 0.902 ± 0.006 could be used for the Cyberknife VSI system reference field. Within measurement uncertainties, the absorbed dose rate measured in the Cyberknife VSI system reference field was found to be independent of the dosimeters used. These results suggest that the absorbed dose measured at a point within a given field size should be the same, regardless the dosimeter used, if their dosimetric characteristics are well known. This highlighted the importance of performing dosimetry by controlling all parameters that could affect the dosimeter response. One can conclude that radiochromic film dosimetry can be considered as an appropriate alternative for measuring absorbed dose to water rate.

Lifetime and shelf life of sealed tritium-filled plasma focus chambers with gas generator

The paper describes the operation features of plasma focus chambers using deuteriumetritium mixture.Handling tritium requires the use of sealed,vacuum-tight plasma focus chambers.In these chambers,there is an accumulation of the impurity gases released from the inside surfaces of the electrodes and the insulator while moving plasma current sheath inside chambers interacting with b-electrons generated due to the decay of tritium.Decay of tritium is also accompanied by the accumulation of helium.Impurities lead to a decreased yield of neutron emission from plasma focus chambers,especially for long term operation.The paper presents an option of absorption type gas generator in the chamber based on porous titanium,which allows to significantly increase the lifetime and shelf life of tritium chambers.It also shows the results of experiments on the comparison of the operation of sealed plasma focus chambers with and without the gas generator.