Dual-salt poly(tetrahydrofuran) electrolyte enables quasi-solid-state lithium metal batteries to operate at -30 ℃

The stable operation of solid-state lithium metal batteries at low temperatures is plagued by severe restrictions from inferior electrolyte-electrode interface compatibility and increased energy barrier for Li^(+)migration.Herein,we prepare a dual-salt poly(tetrahydrofuran)-based electrolyte consisting of lithium hexafluorophosphate and lithium difluoro(oxalato)borate(LiDFOB).The Li-salt anions(DFOB−)not only accelerate the ring-opening polymerization of tetrahydrofuran,but also promote the formation of highly ion-conductive and sustainable interphases on Li metal anodes without sacrificing the Li^(+)conductivity of electrolytes,which is favorable for Li^(+)transport kinetics at low temperatures.Applications of this polymer electrolyte in Li||LiFePO_(4)cells show 82.3%capacity retention over 1000 cycles at 30℃and endow stable discharge capacity at−30℃.Remarkably,the Li||LiFePO4 cells retain 52%of their room-temperature capacity at−20℃and 0.1 C.This rational design of dual-salt polymer-based electrolytes may provide a new perspective for the stable operation of quasi-solid-state batteries at low temperatures.

Research on Hydrodynamics Model Test for Deepsea Open-Framed Remotely Operated Vehicle

This paper presents the features of newly designed hydrodynamics test for the scaled model of 4500 m deepsea open-framed remotely operated vehicle （ROV）, which is being researched and developed by Shanghai Jiao Tong University. Accurate hydrodynamics coefficients measurement and spatial modeling of ROV are significant for the maneuverability and control algorithm. The scaled model of ROV was constructed by 1：1.6. Hydrodynamics coefficients were measured through VPMM and LAHPMM towing test. And dynamics model was derived as a set of equations, describing nonlinear and coupled 5-DOF spatial motions. Rotation control motion was simulated to verify spatial model proposed. Research and application of hydrodynamics coefficients are expected to enable ROV to overcome uncertainty and disturbances of deepsea environment, and accomplish some more challengeable and practical missions.

Acute upper gastrointestinal bleeding in operated stomach: Outcome of 105 cases

AIM: To compare the causes and clinical outcome of patients with acute upper gastrointestinal bleeding (AUGB) and a history of gastric surgery to those with AUGB but without a history of gastric surgery in the past.METHODS: The causes and clinical outcome were compared between 105 patients with AUGB and a history of gastric surgery, and 608 patients with AUGB but without a history of gastric surgery.RESULTS: Patients who underwent gastric surgery in the past were older (mean age: 68.1±11.7 years vs 62.8±17.8 years, P= 0.001), and the most common cause of bleeding was marginal ulcer in 63 patients (60%). No identifiable source of bleeding could be found in 22 patients (20.9%) compared to 42/608 (6.9%) in patients without a history of gastric surgery (P = 0.003). Endoscopic hemostasis was permanently successful in 26 out of 35 patients (74.3%) with peptic ulcers and active bleeding or non-bleeding visible vessel. Nine patients (8.6%) were operated due to continuing or recurrent bleeding,compared to 23/608 (3.8%) in the group of patients without gastric surgery in the past (P= 0.028). Especially in peptic ulcer bleeding patients, emergency surgery was more common in the group of patients with gastric surgery in the past [9/73 (12.3%) vs 19/360 (5.3%), P = 0.025].Moreover surgically treated patients in the past required more blood transfusion (3.3±4.0 vs 1.5±1.7, P = 0.0001) and longer hospitalization time (8.6±4.0 vs 6.9±4.9 d,P = 0.001) than patients without a history of gastric surgery. Mortality was not different between the two groups [4/105 (3.8%) vs 19/608 (3.1%)].CONCLUSION: Upper gastrointestinal bleeding seems to be more severe in surgically treated patients than in non-operated patients.

A real-world data collection framework for a fused dataset creation for joint human and remotely operated vehicle monitoring and anomalous command detection

Unmanned Remotely Operated Vehicles(ROVs)are widely used in safety-critical missions,spanning across monitoring,surveillance,and search and rescue missions.In most cases,the human operator controls the ROV under stressful conditions and in harsh environments.The physical and mental states of the operator are vital as they may cause involuntary movements,issuing unintentional commands due to fatigue or stress.Consequently,a joint monitoring mechanism that will assess the operator's commands can be beneficial in preventing potentially catastrophic events,such as accidents.To this end,in this study,we propose a data collection framework for creating a fused dataset,consisting of data obtained from both the human operator and the ROV,and we integrate stress induction to stimulate stress and fatigue that may affect operators during missions.We optimise the dataset,which includes the operator's physiological signals and inertial measurement unit(IMU)sensor data from the ROV,using data fusion approaches and feature extraction.We evaluate the dataset through the statistical analysis,illustrating a statistical difference between data characterising normal and involuntary commands.Finally,we evaluate the optimised and original datasets over a variety of classifiers,demonstrating an accuracy of 94%and 95%,respectively.

西门子Operate高级编程的旋转坐标系二次开发

应用西门子Operate的Easyscreen功能,简便而实用地实现了卧式加工中心上经常使用的旋转坐标系的相应机床操作,并详细介绍了其高级编程指令的二次开发的全过程。

Study on Simulation of Remotely Operated Underwater Vehicle Spatial Motion

In order to analyze the spatial maneuverability of the remotely operated underwater vehicle(ROV),the 6-DOF motion mathematic model of the ROV was founded.Hydrodynamics were analyzed by using the Taylor series.The thrusters on the ROV were discussed.This paper considers three cases of motion simulation:vertical motion,rotational motion and Z-shape motion.A series of simulation experiments showed that the 6-DOF motion mathematic model was correct and reliable,and also fit with the scene simulation.

Analysis on Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell When Operated in High Temperature Range

This study is to understand the impact of operating condition, especially initial operation temperature （Tini） which is set in high temperature range, on the temperature profile of the interface between PEM （polymer electrolyte membrane） and catalyst layer at the cathode （i.e., the reaction surface） in a single PEFC （polymer electrolyte fuel cell）. A 1D multi-plate heat transfer model based on the temperature data of separator measured using thermograph in a power generation experiment was developed to evaluate the reaction surface temperature （Treact）. This study investigated the effects of flow rate, relative humidity and type of supply gas as well as Tini on the temperature distribution on reaction surface. The results obtained in 02 supply case show that, the temperature rise at the segments near the outlet of cell decreases with increasing Tini irrespective of relative humidity of supply gas （RH）, while it is not seen in air supply case. Regarding the segments except near the outlet in 02 supply case, Treact - Tini increases with increasing Tini for 40% RH. The temperature distribution on reaction surface in 02 supply case is wider with increasing Tini as well as decreasing RH, though that in air supply case is relatively even.

Electronic Load Controller for a Parallel Operated Isolated Asynchronous Generator Feeding Various Loads

This paper presents an investigation on a voltage and frequency controller (VFC), which functions as an improved elec-tronic load controller (IELC) for parallel operated isolated asynchronous generators (IAGs) in an autonomous hydro power generation system. In such type of hydro scheme whole generating system is isolated from the grid and supply electricity to the remote communities. The single point operation of these generators is realized, in such a manner that excitation capacitors, speeds, load, voltage, currents of generators remain constant under various operating conditions. The proposed controller consists of a 3-leg IGBT (Insulated Gate Bipolar Transistor) based voltage source converter (VSC) and a DC chopper with an auxiliary load at the DC bus of the VSC. The IELC controls the reactive and active powers simultaneously for controlling the voltage and frequency under varying consumer loads. Along with voltage and frequency control through single point operation of IAGs driven by uncontrolled pico hydro turbines, the IELC meets the power quality standard an IEEE-519 and it keeps the total harmonic distortion (THD) of the terminal voltage and currents within the limit of 5%. Here the proposed electrical system along with its controller is modeled in MATLAB along with Simulink and PSB (Power System Block-set) toolboxes. Simulation results are presented to demonstrate the capability of proposed controller for an isolated generating system.

How Does the Farmer Cooperatives Operate in Yanbian Area?

After six years of development,the number of farmer cooperatives in Yanbian area was increased from 72 in 2007 to 2600 in 2012.It has become an important part of local modern agricultural operation.Through the survey and research of current status of farmer cooperatives in Yanbian area,we analyze the deficiencies in capital,technology and human resources during the operating to thoroughly understand its operating status.On this basis,we put forth some recommendations for the development of farmer cooperatives in Yanbian area:implementing industrialization operation;developing long-term development strategy;seeking the support of research institutions and colleges;increasing the types of services;enhancing the value-added.

Impact of Thickness of Polymer Electrolyte Membrane on Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell Operated at High Temperature

This study is to understand the impact of operating condition, especially initial operation temperature （Tini） which is set in high temperature range, on the temperature profile of the interface between PEM （polymer electrolyte membrane） and catalyst layer at the cathode （i.e., the reaction surface） in a single PEFC （polymer electrolyte fuel cell）. A 1D multi-plate heat transfer model based on the temperature data of separator measured using thermograph in a power generation experiment was developed to evaluate the reaction surface temperature （Treact）. This study investigated the effects of Tini, flow rate and relative humidity of supply gas as well as thickness of PEM on the temperature distribution on reaction surface. As a result, the impact of flow rate of supply gas on the temperature distribution is not significant irrespective of relative humidity conditions as well as PEM type. When operated at high temperature, the temperature distribution is relatively flat in the case of thicker PEM （Nafion 115）, while Treact rises from the inlet to the outlet large and the temperature distribution is wide in the case of thin PEM （Nafion 211） irrespective of relative humidity condition. Since the water transfer through PEM in the case of Nafion 211 is better than Nafion 115 due to thin PEM, the power generation is promoted along the gas flow with the aid of humidification by water produced from electrochemical reaction.

Impact of Relative Humidity of Supply Gas on Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell When Operated at High Temperature

For improving the performance of stationary PEFC （polymer electrolyte fuel cell） system, the cell operating temperature up to 90℃ will be preferred in Japan during the period from 2020 to 2030. To understand the operation of the PEFC system under relatively high temperature conditions, detail heat and mass transfer analysis is required. The purpose of this study is to analyze the impact of relative humidity of supply gas on temperature distribution on the backside of separator in single ceil of PEFC using Nation membrane at higher temperature e.g. 90℃. The in-plane temperature distribution when power was being generated was measured using thermograph with various relative humidity of supply gases. It was found that the in-plane temperature distribution at the anode was more even than that at the cathode irrespective of the relative humidity of supply gas at the anode and the cathode. The temperature elevated along gas flow through the gas channel at the cathode irrespective of relative humidity of supply gas at the anode and the cathode. The in-plane temperature distribution at the cathode was narrower with the increase in Tini irrespective of relative humidity of supply gas at the cathode, while it was not observed when changing the relative humidity of supply gas at the anode. When the relative humidity of supply gas at cathode decreased, the in-plane temperature distribution at the anode was wider compared to decreasing the relative humidity of supply gas at the anode. The study concluded that the impact of relative humidity of supply gas at both anode and cathode had little impact on the in-plane temperature distribution at the cathode.

Numerical Analysis of Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell when Operated in Elevated Temperature Range

Abstract： The purpose of this study is to analyze the temperature distribution on the interface between the polymer electrolyte membrane and catalyst layer at the cathode in single cell of polymer electrolyte fuel cell when operated in elevated temperature range than usual. In this study, the interface between the polymer electrolyte membrane and catalyst layer at the cathode is named as reaction surface. This study has considered the 1D multi-plate heat transfer model estimating the temperature distribution on the reaction surface and verified with the 3D numerical simulation model solving many governing equations on the coupling phenomena of the polymer electrolyte fuel cell. The 3D numerical simulation model coverers a half size of actual cell including three straight parts and two turn-back corners, which can display the essential phenomena of single cell. The results from both models/simulations agreed well. The effects of initial operation temperature, flow rate, and relative humidity of supply gas on temperature distribution on the reaction surface have been investigated. Though the effect of flow rate of supply gas on temperature distribution on reaction surface has been small, low relative humidity of supply gas has caused higher temperature on the reaction surface compared to high relative humidity of the supply gas. The temperature rise of reaction surface from initial operation temperature has increased with the increasing in initial operation temperature of cell.

Process Adaption of a Small WWTP Operated at Low Loading Conditions for Substantial Energy Savings

The very long tradition of the activated sludge treatment model within the water industry has demonstrated very versatile possibilities to adopt the operation mode for different enhancements. By looking into other treatment models within the activated sludge family it is possible to find alternatives for the operation. This paper concentrates on the possibilities to improve even small WWTP with respect to energy savings. The small plant in Northern Sweden, called Rosvik WWTP, is given as an example. Some important findings related to the intermittent aeration mode may be summarized as follows: 1) An energy savings for the operation of the small WWTP with respect to aeration needs that resulted in a decrease of the energy power supply by more than 35%, as compared with the previous operation based on continuous aeration;2) The up to date effluent levels with respect to the main pollutants have remained at very good levels in 2020, P-level averages 0.16 mg P/l versus consent level < 0.5 mg P/l;COD-level 40 versus < 70 mg/l and BOD7 9 versus < 15 mg/l;3) Sometimes, also improved sludge settling characteristics have been observed, thus providing improved discharge figures;4) The potential to develop an enhanced biological phosphorus removal. There are however some needed conditions to accomplish these improvements: 1) Reliable on-line probes for both oxygen control, SS-concentration control and optionally also for nitrogen control;2) A flexible automation system that allows the needed process modifications to take place;3) And finally, very important dedicated and competent plant operators, with the needed curiosity for operation improvements.

The Impacts of Income from Non-agricultural Industries Operated by Rural households on Farmers' Income

Income from non-agricultural industries operated by rural households is an important income source of farmers' income. According to the Regional Rural Residents' Net Income Per Capita in 2004 issued by the State Statistics Bureau and the relevant statistics of national comprehensive investigation(CGSS2005) in 2005, the impacts of farmers' income gap and farmers' individual features on their income and the impacts of income from non-agricultural industries operated by rural households on farmers' individual income differences are analyzed by applying Hierarchical Linear Models (HLM) as an analysis tool to establish the null model of HLM, excluding the second level model of the second level prediction variables and including the second level model of the second layer prediction variables. The analysis assumes that farmers' individual income varies hugely in different provinces; farmers' individual income has close relation with farmers' individual features; the improvement of income from non-agricultural industries operated by rural households has different impacts on farmers' income.

Numerical Analysis on Temperature Distribution in a Single Cell of PEFC Operated at Higher Temperature by1D Heat Transfer Model and 3D Multi-Physics Simulation Model

This study is to understand the impact of operating conditions, especially initial operation temperature (Tini) which is set in a high temperature range, on the temperature profile of the interface between the polymer electrolyte membrane (PEM) and the catalyst layer at the cathode (i.e., the reaction surface) in a single cell of polymer electrolyte fuel cell (PEFC). A 1D multi-plate heat transfer model based on the temperature data of the separator measured using the thermograph in a power generation experiment was developed to evaluate the reaction surface temperature (Treact). In addition, to validate the proposed heat transfer model, Treact obtained from the model was compared with that from the 3D numerical simulation using CFD software COMSOL Multiphysics which solves the continuity equation, Brinkman equation, Maxwell-Stefan equation, Butler-Volmer equation as well as heat transfer equation. As a result, the temperature gap between the results obtained by 1D heat transfer model and those obtained by 3D numerical simulation is below approximately 0.5 K. The simulation results show the change in the molar concentration of O2 and H2O from the inlet to the outlet is more even with the increase in Tini due to the lower performance of O2 reduction reaction. The change in the current density from the inlet to the outlet is more even with the increase in Tini and the value of current density is smaller with the increase in Tini due to the increase in ohmic over-potential and concentration over-potential. It is revealed that the change in Treact from the inlet to the outlet is more even with the increase in Tini irrespective of heat transfer model. This is because the generated heat from the power generation is lower with the increase in Tini due to the lower performance of O2 reduction reaction.

Impact of Thickness of Polymer Electrolyte Membrane and Gas Diffusion Layer on Temperature Distributions in Polymer Electrolyte Fuel Cell Operated at Temperature around 90℃

Polymer Electrolyte Fuel Cell(PEFC)is desired to be operated at temperature around 90℃ for stationary applications during the period from 2020 to 2025 in Japan.It can be expected thinner polymer electrolyte membrane(PEM)and gas diffusion layer(GDL)would promote the power generation performance of PEFC at this temperature.The aim of this study is to understand the impact of thickness of PEM and GDL on the temperature profile of interface between PEM and catalyst layer at the cathode(i.e.,the reaction surface)in a single PEFC with an initial operation temperature(Tini).An 1D multi-plate heat transfer model based on temperature data of separator measured using thermograph in power generation process was developed to evaluate temperature of the reaction surface(Treact).This study investigated the effect of Tini,flow rate and relative humidity of supply gas on Treact distribution.The study finds that when using thin GDL,the even distribution of Treact – Tini is obtained irrespective of thickness of PEM,Tini and relative humidity conditions.Treact – Tini using Nafion 115 is higher than the other thin PEMs irrespective of Tini and relative humidity conditions.It can be concluded that the even temperature distribution could be achieved by using thin PEM and GDL.

Effects of spot size on the operation mode of Ga As photoconductive semiconductor switch employing extrinsic photoconductivity

To guide the illuminating design to improve the on-state performances of gallium arsenide(GaAs)photoconductive semiconductor switch(PCSS),the effect of spot size on the operation mode of GaAsPCSS based on a semi-insulating wafer with a thickness of 1 mm,triggered by a 1064-nm extrinsic laser beam with the rectangular spot,has been investigated experimentally.It is found that the variation of the spot size in length and width can act on the different parts of the output waveform integrating the characteristics of the linear and nonlinear modes,and then significantly boosts the PCSS toward different operation modes.On this basis,a two-channel model containing the active and passive parts is introduced to interpret the relevant influencing mechanisms.Results indicate that the increased spot length can peak the amplitude of static domains in the active part to enhance the development of the nonlinear switching,while the extended spot width can change the distribution of photogenerated carriers on both parts to facilitate the linear switching and weaken the nonlinear switching,which have been proved by comparing the domain evolutions under different spot sizes.

Why and how retailing companies in China should operate in low-carbon mode?

Nowadays low-carbon development has become a hot issue of the whole world.This article first introduces the background of low-carbon economy,and then explains the importance of retailing companies in social economy and the reasons why they should operate in low-carbon mode.More specifically,low-carbon operation can not only improve the competitiveness of a retailing company by reducing operation cost and formatting good corporate image,but also benefit the whole society by reducing environment pollution and promoting low-carbon consumption and production.Only by adopting low-carbon operation pattern can retailing companies confront the fierce international competition.To illustrate the above point of view,several cases of famous western retailing companies will be analyzed in this essay.Tesco,Wal-Mart and Carrefour are all typical examples in low-carbon operation because they all have great green and sustainability initiatives.Based on the advanced experiences of the above-mentioned companies,this essay discusses the low-carbon operation ways,putting forward some valuable suggestions on this problem.From a technical perspective,retailing companies should adopt advanced technologies relating to low-carbon operation.On the other hand,management level of retailing companies should be enhanced to ensure the application effect of low-carbon technologies.Retailing companies should improve the ability of internal management to excavate the internal potential and build green supply chain to corporate with strategic partners.Finally,this article gives the conclusion of the whole analysis.

Fractal Fractional Order Operators in Computational Techniques for Mathematical Models in Epidemiology

New fractional operators, the COVID-19 model has been studied in this paper. By using different numericaltechniques and the time fractional parameters, the mechanical characteristics of the fractional order model areidentified. The uniqueness and existence have been established. Themodel’sUlam-Hyers stability analysis has beenfound. In order to justify the theoretical results, numerical simulations are carried out for the presented methodin the range of fractional order to show the implications of fractional and fractal orders.We applied very effectivenumerical techniques to obtain the solutions of themodel and simulations. Also, we present conditions of existencefor a solution to the proposed epidemicmodel and to calculate the reproduction number in certain state conditionsof the analyzed dynamic system. COVID-19 fractional order model for the case of Wuhan, China, is offered foranalysis with simulations in order to determine the possible efficacy of Coronavirus disease transmission in theCommunity. For this reason, we employed the COVID-19 fractal fractional derivative model in the example ofWuhan, China, with the given beginning conditions. In conclusion, again the mathematical models with fractionaloperators can facilitate the improvement of decision-making for measures to be taken in the management of anepidemic situation.

A Short Term Review of Operated Cases in the Plastic Surgery Unit at the Komfo Anokye Teaching Hospital, Kumasi, Ghana

Introduction: Surgical problems are of much disturbance to the world and should therefore be given serious attention. The prevalence of these surgical problems, has made plastic surgery become a broadly relevant and acceptable way for addressing problems like injuries, congenital anomalies, surgical infections and malignancies among others. Aim: This study is to quantify and characterize surgical procedures done in the plastic surgery theatre located in the new Accident and Emergency (A & E) Building of KATH. Materials and Methods: Data were obtained from the Operation Register/Theatre Books in the plastic surgery theatre at the A & E Centre on cases operated on from October 1, 2009 to September 30, 2012. Data entry, presentation and analysis were done using Statistical Package for the Social Sciences (SPSS) 20.0 version. Results: Adults formed the majority of patients who sought for plastic surgery with a percentage of 70.3%. The male patients also outnumbered the females recording (61.5%) out of the total number of patients. Most of the cases recorded were acquired cases (93.2%). Reconstructive surgery was the commonest operation performed (30%);in 53.8% cases general anaesthesia was used. Conclusion: Among all the procedures used reconstructive surgery was the commonest surgery performed in the unit and general anaesthesia was the most type of anaesthesia used for the operations.