A Study on Refractive Index Sensors Based on Optical Micro-Ring Resonators

In this work, the behavior of refractive index sensors based on optical micro-ring resonators is studied in detail. Using a result of waveguide perturbation theory in combination with numerical simulations, the optimum design parameters of the system, maximizing the sensitivity of the sensor, are determined. It is found that, when optimally designed, the sensor can detect relative refractive index changes of the order of △n/n≈3×10^-4, assuming that the experimental setup can detect relative wavelength shifts of the order of △λ/λ≈3×10^-5. The behavior of the system as bio-sensor has also been examined. It is found that, when optimally designed, the system can detect refractive index changes of the order of △n≈ 10^-3 for a layer thickness of t=- 10 nm, and changes in the layer thickness of the order of △t≈0.24 nm, for a refractive index change of △n=0.05.

Compact Optical Add-Drop De-Multiplexers with Cascaded Micro-Ring Resonators on SOI

A four-channel integrated optical wavelength de-multiplexer is experimentally illustrated on a silicon-on-insulator （SO1） substrate. With the aid of cascaded micro-ring resonators, the whole performance of the wavelength de- multiplexer is improved, such as 3 dB bandwidth and channel crosstalk. Based on the transform matrix theory, a four-channel wavelength de-multiplexer with average channel spacing 4.5±0.5 nm （3 dB bandwidth - 2 ± 0.5 nm） is demonstrated at telecommunication bands. For each channel, the extinction at the adjacent channel is below -39dB and the out-of-band rejection ratio is up to 40dB. The channel dropping loss is below 5dB in the five FSR spectral response periods （near 100 nm）.

Tunable optical filter using second-order micro-ring resonator

In this paper, we design and fabricate a silicon integrated optical filter consisting of two cascaded micro-ring resonators and two straight waveguides. Two micro-heaters are fabricated on the top of two micro-rings respectively, which are employed to modulate the micro-rings to perform the function of a tunable optical filter by the thermo–optic effect. The static response test indicates that the extinction ratio and 3-d B bandwidth are 29.01 d B and 0.21 nm respectively, the dynamic response test indicates that the 10%–90% rise and 90%–10% fall time of the filter are 16 μs and 12 μs, respectively,which can meet the requirements of optical communication and information processing. Finally, the power consumption of the device is also characterized, and the total power consumption is about 9.43 m W/nm, which has been improved efficiently.

AFM Analysis on Polymer Optical Micro-Resonators: Investigation on Quality Factor Origin

This paper deals with the surface analysis of spherical polymeric optical micro-resonators in order to correlate surface defects with optical characteristics. Atomic force microscopy was used on structures to determine surface quality, which is the main origin of optical scattering losses. Surface morphologies were numerically treated to enable a relevant investigation on surface parameters such as root mean square (RMS) roughness (30.1 +/- 3.0 nm) or correlation length (few microns) necessary to express optical quality factors. A statistical analysis was conducted for calibration of these parameters as a function of cavities’ diameter. Results are in perfect agreement with spectral analyses performed in parallel on others structures. This comparison highlights the main role of scattering losses on quality factor origin.

Optical pulling force on nanoparticle clusters with gain due to Fano-like resonance

We demonstrate that,in a simple linearly-polarized plane wave,the optical pulling forces on nanoparticle clusters with gain can be induced by the Fano-like resonance.The numerical results based on the full-wave calculation show that the optical pulling forces can be attributed to the recoil forces for the nanoparticle clusters composed of dipolar nanoparticles with three different configurations.Interestingly,the recoil forces giving rise to optical pulling forces are exactly dominated by the coupling term between the electric and magnetic dipoles excited in the nanoparticle clusters,while other higherorder terms have a negligible contribution.In addition,the optical pulling force can be tailored by modulating the Fano-like resonance via either the particle size or the gain magnitude,offering an alternative freedom degree for optical manipulations of particle clusters.

Classic analogue of Autler–Townes-splitting transparency using a single magneto-optical ring resonator

We show that an optical transparency can be obtained by using only one single magneto-optical ring resonator. This effect is based on the splitting of counterclockwise and clockwise modes in the ring resonator. Within a proposed resonator-waveguide configuration the superposition between the two degeneracy broken modes produces a transparency window,which can be closed, open, and modified by tuning the applied magnetic field. This phenomenon is an analogue of Autler–Townes splitting, and the magnetic field is equivalent to the strong external pump field. We provide a theoretic analysis on the induced transparency, and numerically demonstrate the effect using full-wave simulation. Feasible implication of this effect and its potential applications are also discussed.

Orthogonally polarized RF optical single sideband generation with integrated ring resonators

We review recent work on narrowband orthogonally polarized optical RF single sideband generators as well as dualchannel equalization,both based on high-Q integrated ring resonators.The devices operate in the optical telecommunications C-band and enable RF operation over a range of either fixed or thermally tuneable frequencies.They operate via TE/TM mode birefringence in the resonator.We achieve a very large dynamic tuning range of over 55 dB for both the optical carrier-to-sideband ratio and the dual-channel RF equalization for both the fixed and tunable devices.

Dual-channel fiber-optic surface plasmon resonance sensor with cascaded coaxial dual-waveguide D-type structure and microsphere structure

To address the restriction of fiber-optic surface plasmon resonance(SPR) sensors in the field of multi-sample detection, a novel dual-channel fiber-optic SPR sensor based on the cascade of coaxial dual-waveguide D-type structure and microsphere structure is proposed in this paper. The fiber sidepolishing technique converts the coaxial dual-waveguide fiber into a D-type one, and the evanescent wave in the ring core leaks, generating a D-type sensing region;the fiber optic fused ball push technology converts the coaxial dual waveguides into microspheres, and the stimulated cladding mode evanescent wave leaks, producing the microsphere sensing region. By injecting light into the coaxial dual-waveguide middle core alone, the sensor can realize single-stage sensing in the microsphere sensing area;it can also realize dual-channel sensing in the D-type sensing area and microsphere sensing area by injecting light into the ring core. The refractive index measurement ranges for the two channels are 1.333–1.365 and 1.375–1.405, respectively, with detection sensitivities of 981.56 nm/RIU and 4138 nm/RIU. The sensor combines wavelength division multiplexing and space division multiplexing technologies, presenting a novel research concept for multi-channel fiber SPR sensors.

Design and simulation of a silicon-based hybrid integrated optical gyroscope system

By combining a silicon-based lithium niobate modulator and a silicon-based Si3N4resonator with silicon-based photonics technology,a highly systematic design of a hybrid integrated optical gyroscope with enhanced reciprocity sensitivity and a dual micro-ring structure is proposed for the first time in this paper.The relationship between the device's structural parameters and optical performance is also analyzed by constructing a complete simulation link,which provides a theoretical design reference to improve the system's sensitivity.When the wavelength is 1550 nm,the conversion frequency of the dual-ring optical path is 50 MHz,the coupling coefficient is 0.2,and the radius R is 1000μm,the quality factor of the silicon-based Si_(3)N_(4)resonator is 2.58×10^(5),which is 1.58 times that of the silicon-on-insulator resonator.Moreover,the effective number of times the light travels around the ring before leaving the micro-ring is 5.93,which is 1.62 times that of the silicon-on-insulator resonator.The work fits the gyro dynamic output diagram,and solves the problem of low sensitivity at low speed by setting the phase offset.This results provide a basis for the further optimization of design and chip processing of the integrated optical gyroscope.

Highly sensitive digital optical sensor with large measurement range based on the dual-microring resonator with waveguide-coupled feedback

We propose a novel high-performance digital optical sensor based on the Mach-Zehnder interferential effect and the dual-microring resonators with the waveguide-coupled feedback. The simulation results show that the sensitivity of the sensor can be orders of magnitude higher than that of aconventional sensor, and high quality factor is not critical in it. Moreover, by optimizing the length of the feedback waveguide to be equal to the perimeter of the ring, the measurement range of the proposed sensor is twice as much as that of the conventional sensor in the weak coupling case.

Low noise,continuous-wave single-frequency 1.5-μm laser generated by a singly resonant optical parametric oscillator

We report a low noise continuous-wave （CW） single-frequency 1.5-μm laser source obtained by a singly resonant optical parametric oscillator （SRO） based on periodically poled lithium niobate （PPLN）. The SRO was pumped by a CW single-frequency Nd：YVO4 laser at 1.06μm. The 1.02 W of CW single-frequency signal laser at 1.5 μm was obtained at pump power of 6 W. At the output power of around 0.75 W, the power stability was better than ±l.5% and no mode-hopping was observed in 30 min and frequency stability was better than 8.5 MHz in 1 min. The signal wavelength could be tuned from 1.57 to 1.59 μm by varying the PPLN temperature. The 1.5-μm laser exhibits low noise characteristics, the intensity noise of the laser reaches the shot noise limit （SNL） at an analysis frequency of 4 MHz and the phase noise is less than 1 dB above the SNL at analysis frequencies above 10 MHz.

Resonantly enhanced second-and third-harmonic generation in dielectric nonlinear metasurfaces

Nonlinear dielectric metasurfaces provide a promising approach to control and manipulate frequency conversion optical processes at the nanoscale,thus facilitating both advances in fundamental research and the development of new practical applications in photonics,lasing,and sensing.Here,we employ symmetry-broken metasurfaces made of centrosymmetric amorphous silicon for resonantly enhanced second-and third-order nonlinear optical response.Exploiting the rich physics of optical quasi-bound states in the continuum and guided mode resonances,we comprehensively study through rigorous numerical calculations the relative contribution of surface and bulk effects to second-harmonic generation(SHG)and the bulk contribution to third-harmonic generation(THG) from the meta-atoms.Next,we experimentally achieve optical resonances with high quality factors,which greatly boosts light-matter interaction,resulting in about 550 times SHG enhancement and nearly 5000-fold increase of THG.A good agreement between theoretical predictions and experimental measurements is observed.To gain deeper insights into the physics of the investigated nonlinear optical processes,we further numerically study the relation between nonlinear emission and the structural asymmetry of the metasurface and reveal that the generated harmonic signals arising from linear sharp resonances are highly dependent on the asymmetry of the meta-atoms.Our work suggests a fruitful strategy to enhance the harmonic generation and effectively control different orders of harmonics in all-dielectric metasurfaces,enabling the development of efficient active photonic nanodevices.

Sub-nanosecond optical switch based on silicon racetrack resonator

We experimentally demonstrate a small-size and high-speed silicon optical switch based on the free carrier plasma dispersion in silicon. Using an embedded racetrack resonator with a quality factor of 7400, the optical switch shows an extinction ratio exceeding 13 dB with a footprint of only 2.2 × 10-3 mm^2. Moreover, a novel pre-emphasis technique is introduced to improve the optical response performance and the rise and the fall times are reduced down to 0.24 ns and 0.42 ns respectively, which are 25% and 44% lower than those without the pre-emphasis.

High-Efficiency Mid-Infrared Picosecond MgO:PPLN Single Resonant Optical Parametric Oscillator

We demonstrate a high-emciency mid-infrared picosecond optical parametric oscillator （OPO） based on MgO doped periodically poled lithium niobate （MgO：PPLN） with a laser diode array （LDA） pumped Innoslab amplifier as the pumping source. Under a 16 W synchronously pumping power, 4.5 W of idler light at 2896nm is obtained. A tuning range of idler light from 2688nm to 3016nm is achieved, within which the highest optical-optical conversion ettlciency from pump power to OPO output is 35.1%. Moreover, a signal light of -500mW from 1644 to 1700nm with a repetition rate of 233.8 MHz is generated.

Raman lasing and other nonlinear effects based on ultrahigh-Q CaF_(2)optical resonator

The calcium fluoride(CaF_(2))whispering gallery mode crystalline resonator is an excellent platform for nonlinear optical applications because of the decreasing in threshold caused by ultrahigh quality(Q)factor.In this paper,we achieved the observation of Raman lasing,first-order Raman comb,and second-order Raman lasing in a CaF_(2)disk resonator with a diameter of 4.96 mm and an ultrahigh-Q of 8.43×10^(8)at 1550-nm wavelength.We also observed thermal effects in CaF_(2)disk resonator,and the threshold of thermo-optical oscillation is approximately coincident with Raman lasing,since the intracavity power increases rapidly when the power reaches the threshold,and higher input pump power results in longer thermal drift and higher Raman emission power.With a further increase in pump power,the optical frequency combs range is from 1520 nm to 1650 nm,with a wavelength interval of 4×FSR.It is a promising candidate for optical communication,biological environment monitoring,spectral analysis,and microwave signal sources.

Refractive Plasmonic Sensor Based on Fano Resonances in an Optical System

A symmetric plasmonie structure consisting of metal-insulator metal waveguide, groove studied, which supports double Fano resonances deriving from two different mechanisms and slot cavities is One of the Fano resonances originates from the interference between the resonances of groove and slot cavities, and the other comes from the interference between slot cavities. The spectral line shapes and the peaks of the double Fano resonances can be modulated by changing the length of the slot cavities and the height of the groove. Furthermore, the wavelength of the resonance peak has a linear relationship with the length of the slot cavities. The proposed plasmonic nanosensor possesses a sensitivity of 800nm/RIU and a figure of merit of 3150, which may have important applications in switches, sensors, and nonlinear devices.

X-Ray Diffraction, Electron Paramagnetic Resonance and Optical Absorption Study of Bauxite

The bauxite mineral obtained from Araku, Vishakapatnam district of Andhra Pradesh, India is used in the present work. Structural characterization was performed by X-ray diffraction (XRD). The mineral was found to be gibbsite in phase. The transitional metal ions present were investigated using electron paramagnetic resonance (EPR) and optical absorption spectra. The EPR results suggest that Fe3+ has replaced Al3+ in the unit cell of bauxite. The optical absorption spectrum is due to Fe3+ which indicates that it is in distorted octahedral environment. The near-infrared (NIR) spectrum is due to water fundamentals and combination overtones, which confirm the formula of the compound. The impurities in the mineral are identified using spectroscopic techniques.

Single atoms transferring between a magneto-optical trap and a far-off-resonance optical dipole trap

Based on our work on single cesium atoms trapped in a large-magnetic-gradient vapour-cell magneto-optical trap （MOT）, the signal-to-noise ratio （SNR） is remarkably improved. Also a far-off-resonance optical dipole trap （FORT） formed by a strongly-focused 1064 nm single frequency Nd：YVO4 laser beam is introduced. One cesium atom is prepared in the MOT, and then it can transfer successfully between the MOT and the FORT which is overlapped with the MOT. Utilizing the effective transfer, the lifetime of single atoms trapped in the FORT is measured to be 6.9± 0.3 s. Thus we provide a system where the atomic qubit can be coherently manipulated.

A Prediction Model for Detecting Dysthyroid Optic Neuropathy Based on Clinical Factors and Imaging Markers of the Optic Nerve and Cerebrospinal Fluid in the Optic Nerve Sheath

Objective This study aimed to develop and test a model for predicting dysthyroid optic neuropathy(DON)based on clinical factors and imaging markers of the optic nerve and cerebrospinal fluid(CSF)in the optic nerve sheath.Methods This retrospective study included patients with thyroid-associated ophthalmopathy(TAO)without DON and patients with TAO accompanied by DON at our hospital.The imaging markers of the optic nerve and CSF in the optic nerve sheath were measured on the water-fat images of each patient and,together with clinical factors,were screened by Least absolute shrinkage and selection operator.Subsequently,we constructed a prediction model using multivariate logistic regression.The accuracy of the model was verified using receiver operating characteristic curve analysis.Results In total,80 orbits from 44 DON patients and 90 orbits from 45 TAO patients were included in our study.Two variables(optic nerve subarachnoid space and the volume of the CSF in the optic nerve sheath)were found to be independent predictive factors and were included in the prediction model.In the development cohort,the mean area under the curve(AUC)was 0.994,with a sensitivity of 0.944,specificity of 0.967,and accuracy of 0.901.Moreover,in the validation cohort,the AUC was 0.960,the sensitivity was 0.889,the specificity was 0.893,and the accuracy was 0.890.Conclusions A combined model was developed using imaging data of the optic nerve and CSF in the optic nerve sheath,serving as a noninvasive potential tool to predict DON.

An all-optical 1*2 de-multiplexer based on two-dimensional nonlinear photonic crystal ring resonators

In this work,a new configuration of an all-optical nonlinear de-multiplexer gate based on two-dimensional(2D)photonic crystals(Ph C)is proposed.The gate is considered in the double-ring resonator shaped structure of silicon rods.In order to have a more functional structure,some defect rods made of nonlinear materials were positioned in the structure.Considering the functionality of the structure,photonic band gap(PBG),field distribution and transmitted power spectra are investigated.Plane wave expansion and finite difference time domain(FDTD)methods are utilized for extracting the PBG and field distribution diagrams.The remarkable dimension,bit rate,maximum intensity and contrast ratio of 116.64μm2,3.125 Tbit/s,97%and 40.2 dB are obtained,respectively,which make the gate an appropriate candidate for utilization in optical integrated circuits.