Solvent-free selective oxidation of cyclohexane with molecular oxygen over manganese oxides:Effect of the calcination temperature

The effects of calcination temperature on the physicochemical properties of manganese oxide catalysts prepared by a precipitation method were assessed by X-ray diffraction,N2 adsorption-desorption,X-ray photoelectron spectroscopy,H2 temperature-programmed reduction,O2 temperature-programmed desorption,and thermogravimetry-differential analysis.The catalytic performance of each of these materials during the selective oxidation of cyclohexane with oxygen in a solvent-free system was subsequently examined.It was found that the MnOx-500 catalyst,calcined at 500 °C,consisted of a Mn2O3 phase in addition to Mn5O8 and Mn3O4 phases and possessed a low surface area.Unlike MnOx-500,the MnOx-400 catalyst prepared at 400 °C was composed solely of Mn3O4 and Mn5O8 and had a higher surface area.The pronounced catalytic activity of this latter material for the oxidation of cyclohexene was determined to result from numerous factors,including a higher concentration of surface adsorbed oxygen,greater quantities of the surface Mn4＋ ions that promote oxygen mobility and the extent of O2 adsorption and reducibility on the catalyst.The effects of various reaction conditions on the activity of the MnOx-400 during the oxidation of cyclohexane were also evaluated,such as the reaction temperature,reaction time,and initial oxygen pressure.Following a 4 h reaction at an initial O2 pressure of 0.5 MPa and 140 °C,an 8.0% cyclohexane conversion and 5.0% yield of cyclohexanol and cyclohexanone were achieved over the MnOx-400 catalyst.In contrast,employing MnOx-500 resulted in a 6.1% conversion of cyclohexane and 75% selectivity for cyclohexanol and cyclohexanone.After being recycled through 10 replicate uses,the catalytic activity of the MnOx-400 catalyst was unchanged,demonstrating its good stability.

Highly efficient cobalt-doped carbon nitride polymers for solvent-free selective oxidation of cyclohexane

Selective oxidation of saturated hydrocarbons with molecular oxygen has been of great interest in catalysis, and the development of highly efficient catalysts for this process is a crucial challenge. A new kind of heterogeneous catalyst, cobalt-doped carbon nitride polymer(g-C_3N_4),was harnessed for the selective oxidation of cyclohexane. X-ray diffraction, Fourier transform infrared spectra and high resolution transmission electron microscope revealed that Co species were highly dispersed in g-C_3N_4 matrix and the characteristic structure of polymeric g-C_3N_4 can be retained after Co-doping, although Co-doping caused the incomplete polymerization to some extent. Ultraviolet-visible, Raman and X-ray photoelectron spectroscopy further proved the successful Co doping in g-C_3N_4 matrix as the form of Co(Ⅱ)-N bonds. For the selective oxidation of cyclohexane, Co-doping can markedly promote the catalytic performance of g-C_3N_4 catalyst due to the synergistic effect of Co species and gC_3N_4 hybrid. Furthermore, the content of Co largely affected the activity of Co-doped g-C_3N_4 catalysts, among which the catalyst with 9.0 wt%Co content exhibited the highest yield(9.0%) of cyclohexanone and cyclohexanol, as well as a high stability. Meanwhile, the reaction mechanism over Co-doped g-C_3N_4 catalysts was elaborated.

The selective deposition of Fe species inside ZSM-5 for the oxidation of cyclohexane to cyclohexanone

The design of efficient iron-based catalysts remains a great challenge for selective cyclohexane oxidation to cyclohexanone under mild conditions.Because of the complex distribution of iron location on the support,the selectivity is always low.Here,we report a general strategy to selectively deposit highly-dispersed FeO_(x) into the micropore of ZSM-5 by atomic layer deposition(ALD).The framework of ZSM-5 and the Bronsted acid sites are intact during ALD,and the Fe species are selectively deposited onto the defect and Lewis acid sites of ZSM-5.Besides,more Fe–O–Si bonds are formed over FeO_(x)/ZSM-5 with a low loading of Fe,while FeO_(x) nanoparticles are generated at high Fe loading.They cannot be realized by the traditional solution method.The obtained FeO_(x)/ZSM-5 catalysts perform high selectivity of cyclohexanone(92%–97%),and ALD cycle numbers of FeO_(x) control the activity.Compared with the Fe nanoparticles,the Fe–O–Si species performs higher turnover frequency and stability in the oxidation reaction.