In_2O_3∶SnO_2(ITO) thin films were fabricated on the substrate of flexible polyethylene terephthalate(PET) by DC magnetron sputtering from a ceramic target of In_2O_3/SnO_2(90∶10). Properties of the thin films were ...In_2O_3∶SnO_2(ITO) thin films were fabricated on the substrate of flexible polyethylene terephthalate(PET) by DC magnetron sputtering from a ceramic target of In_2O_3/SnO_2(90∶10). Properties of the thin films were characterized by X-ray diffraction(XRD), four-point probe, Hall-effect measurement, UV-Vis spectrophotometer, and scanning electron microscopy(SEM). The effects of sputtering pressure, oxygen partial pressure and deposition temperature on properties of microstructure and optoelectronics properties of PET/ITO thin films were investigated in detail. High-quality ITO thin films on PET substrates with the resistivity as low as 8.5×10-4 Ω·cm and the optical transmittance over 80% in the visible spectrum range were obtained.展开更多
Flexible electronics have been recently paid much attention. A flexible substrate (Organic resin film) is indispensable component for flexible devices. Though PET film is low-cost organic film, low heat-resistance of ...Flexible electronics have been recently paid much attention. A flexible substrate (Organic resin film) is indispensable component for flexible devices. Though PET film is low-cost organic film, low heat-resistance of PET film limits its application as a flexible device substrate. We have developed heat-resistant PET which does not deteriorate even at 190°C heat treatment for one hour. An excimer light was irradiated onto a polysi-lazane (PHPS: perhydropolysilane)-coated film to form a dense silicon-dioxide (SiO2) layer on a PET film, and the heat-resistance property of the formed film was examined. Changes of surface state and cross-sectional structure of the formed film due to heat treatment were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM). Compared to normal PET, which is deteriorated and whitened by heat treatment of about 110°C - 120°C, the SiO2-coated PET film maintains transparency and does not deteriorate after heat treatment at 180°C - 190°C for one hour. This high heat resistance is due to a dense SiO2 film formed on the surface that prevents surface precipitation and crystallization of low-molecular-weight oligomers (which are the cause of thermal degradation of PET). It is expected that enhancing the heat resistance of PET—which has high versatility and low cost—to about 180°C to 190°C will allow SiO2-film-coated PET to be developed as a film substrate for flexible devices.展开更多
采用低温磁控溅射技术在涤纶纺粘非织造布表面沉积ITO(Indium Tin Oxide,铟锡氧化物)薄膜,利用原子力显微镜(AFM)观察ITO纳米薄膜在纤维表面沉积的微观结构,并较为系统地分析了溅射时间、溅射功率、氧气流量、气体压力以及基底温度对IT...采用低温磁控溅射技术在涤纶纺粘非织造布表面沉积ITO(Indium Tin Oxide,铟锡氧化物)薄膜,利用原子力显微镜(AFM)观察ITO纳米薄膜在纤维表面沉积的微观结构,并较为系统地分析了溅射时间、溅射功率、氧气流量、气体压力以及基底温度对ITO透明导电薄膜微结构的影响。得到以下结论:沉积时间的长短、工作气体压力的大小对成膜的均匀性有很大影响;较高的射频溅射功率将导致纳米颗粒因团聚而增大;而氧气流量的大小则影响着颗粒结晶程度的好坏和晶粒尺寸的大小;基底温度升高则会导致颗粒产生热迁移现象。展开更多
基金Chinese Ministry of Science and Technology for financial support under construct(2003AA513010)
文摘In_2O_3∶SnO_2(ITO) thin films were fabricated on the substrate of flexible polyethylene terephthalate(PET) by DC magnetron sputtering from a ceramic target of In_2O_3/SnO_2(90∶10). Properties of the thin films were characterized by X-ray diffraction(XRD), four-point probe, Hall-effect measurement, UV-Vis spectrophotometer, and scanning electron microscopy(SEM). The effects of sputtering pressure, oxygen partial pressure and deposition temperature on properties of microstructure and optoelectronics properties of PET/ITO thin films were investigated in detail. High-quality ITO thin films on PET substrates with the resistivity as low as 8.5×10-4 Ω·cm and the optical transmittance over 80% in the visible spectrum range were obtained.
文摘Flexible electronics have been recently paid much attention. A flexible substrate (Organic resin film) is indispensable component for flexible devices. Though PET film is low-cost organic film, low heat-resistance of PET film limits its application as a flexible device substrate. We have developed heat-resistant PET which does not deteriorate even at 190°C heat treatment for one hour. An excimer light was irradiated onto a polysi-lazane (PHPS: perhydropolysilane)-coated film to form a dense silicon-dioxide (SiO2) layer on a PET film, and the heat-resistance property of the formed film was examined. Changes of surface state and cross-sectional structure of the formed film due to heat treatment were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM). Compared to normal PET, which is deteriorated and whitened by heat treatment of about 110°C - 120°C, the SiO2-coated PET film maintains transparency and does not deteriorate after heat treatment at 180°C - 190°C for one hour. This high heat resistance is due to a dense SiO2 film formed on the surface that prevents surface precipitation and crystallization of low-molecular-weight oligomers (which are the cause of thermal degradation of PET). It is expected that enhancing the heat resistance of PET—which has high versatility and low cost—to about 180°C to 190°C will allow SiO2-film-coated PET to be developed as a film substrate for flexible devices.
文摘采用低温磁控溅射技术在涤纶纺粘非织造布表面沉积ITO(Indium Tin Oxide,铟锡氧化物)薄膜,利用原子力显微镜(AFM)观察ITO纳米薄膜在纤维表面沉积的微观结构,并较为系统地分析了溅射时间、溅射功率、氧气流量、气体压力以及基底温度对ITO透明导电薄膜微结构的影响。得到以下结论:沉积时间的长短、工作气体压力的大小对成膜的均匀性有很大影响;较高的射频溅射功率将导致纳米颗粒因团聚而增大;而氧气流量的大小则影响着颗粒结晶程度的好坏和晶粒尺寸的大小;基底温度升高则会导致颗粒产生热迁移现象。
