The gas barrier film formation technique using simultaneous photo-irradiation and heat-treatment has been researched on alicyclic polyimide film coated with a polysilazane solution. A fine SiO2 thin film on polyimide ...The gas barrier film formation technique using simultaneous photo-irradiation and heat-treatment has been researched on alicyclic polyimide film coated with a polysilazane solution. A fine SiO2 thin film on polyimide film was formed at low temperatures, which greatly improved the substrate’s gas barrier characteristics by this technique. The values of gas barrier characteristics depended on the substrate temperature at the time of photo-irradiation. For photo-irradiated thin film heat-treated to 150°C, the water vapor transmission rate and oxygen transmission rate fell below the equipment measurement limit of 0.02 g/m2/day and 0.02 cm3/m2/day, respectively. This polyimide film with a gas-barrier film coating has good transmittance in the region of visible light, heat resistance, and flexibility.展开更多
A new kind of conjugated polymer, acetylenic polysilazane was prepared by ammono- lysis of acetylenic dimethylchlorosilane. The polymer was characterized by 29Si、13C NMR and elemental analysis.
The effects of excimer light irradiation on polysilazane coatings formed on PET films with vacuum-evaporated SiO2 coatings and the effects of these coatings on gas barrier characteristics have been investigated. The t...The effects of excimer light irradiation on polysilazane coatings formed on PET films with vacuum-evaporated SiO2 coatings and the effects of these coatings on gas barrier characteristics have been investigated. The temperature during light irradiation has a large effect on the coating’s molecular structure and gas barrier characteristics. When irradiation was performed at 100℃, the polysilazane coating transformed into a silica coating, and a compact silica coating at a much lower temperature than with heat treatment alone was produced. Surface irregularities in the vapor-deposited silica coating were smoothed out by the formation of a polysilazane coating, which was transformed into a compact silica coating when irradiated with light, resulting in a significant improvement in the gas barrier characteristics. The water vapor permeability of the thin coating irradiated with excimer light at 100℃ showed only 0.04 g/m2•day (40℃, 90% RH). According to the results of investigation of temperature variation of water-vapor permeability, it is inferred that the developed film has an excellent gas barrier value, namely, 4.90 × 10–4 g/m2•day at 25℃. This gas barrier coated PET film is transparent and flexible, and can be used in the fabrication of flexible electronics. Also, the proposed fabrication method effectively provides a simple low-cost and low-temperature fabrication technique without the need for high vacuum facility.展开更多
Flexible electronics have been recently paid much attention. A flexible substrate (Organic resin film) is indispensable component for flexible devices. Though PET film is low-cost organic film, low heat-resistance of ...Flexible electronics have been recently paid much attention. A flexible substrate (Organic resin film) is indispensable component for flexible devices. Though PET film is low-cost organic film, low heat-resistance of PET film limits its application as a flexible device substrate. We have developed heat-resistant PET which does not deteriorate even at 190°C heat treatment for one hour. An excimer light was irradiated onto a polysi-lazane (PHPS: perhydropolysilane)-coated film to form a dense silicon-dioxide (SiO2) layer on a PET film, and the heat-resistance property of the formed film was examined. Changes of surface state and cross-sectional structure of the formed film due to heat treatment were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM). Compared to normal PET, which is deteriorated and whitened by heat treatment of about 110°C - 120°C, the SiO2-coated PET film maintains transparency and does not deteriorate after heat treatment at 180°C - 190°C for one hour. This high heat resistance is due to a dense SiO2 film formed on the surface that prevents surface precipitation and crystallization of low-molecular-weight oligomers (which are the cause of thermal degradation of PET). It is expected that enhancing the heat resistance of PET—which has high versatility and low cost—to about 180°C to 190°C will allow SiO2-film-coated PET to be developed as a film substrate for flexible devices.展开更多
High strength and high toughness are mutually exclusive in structural materials.In ceramic materials,increasing toughness usually depends on the introduction of a ductile phase that reduces the strength and high-tempe...High strength and high toughness are mutually exclusive in structural materials.In ceramic materials,increasing toughness usually depends on the introduction of a ductile phase that reduces the strength and high-temperature stability of the material.In this work,vat photopolymerization 3D printing technology was used to achieve toughening of ceramic composite material.The friction sliding of the 3D-printed ceramic macrolayer structure results in effective energy dissipation and redistribution of strain in the whole structure,and macroscale toughening of the ceramic material is realized.In addition,the bridging and elongation of the crack in situ amorphous ceramic whiskers were significant microscopic toughening results,coupled with the toughening of the crack tip of nano-ZrO_(2).Multiscale collaborative toughening methods based on 3D-printed ceramics should find wide applications for materials in service at extreme high temperatures.展开更多
文摘The gas barrier film formation technique using simultaneous photo-irradiation and heat-treatment has been researched on alicyclic polyimide film coated with a polysilazane solution. A fine SiO2 thin film on polyimide film was formed at low temperatures, which greatly improved the substrate’s gas barrier characteristics by this technique. The values of gas barrier characteristics depended on the substrate temperature at the time of photo-irradiation. For photo-irradiated thin film heat-treated to 150°C, the water vapor transmission rate and oxygen transmission rate fell below the equipment measurement limit of 0.02 g/m2/day and 0.02 cm3/m2/day, respectively. This polyimide film with a gas-barrier film coating has good transmittance in the region of visible light, heat resistance, and flexibility.
文摘A new kind of conjugated polymer, acetylenic polysilazane was prepared by ammono- lysis of acetylenic dimethylchlorosilane. The polymer was characterized by 29Si、13C NMR and elemental analysis.
文摘The effects of excimer light irradiation on polysilazane coatings formed on PET films with vacuum-evaporated SiO2 coatings and the effects of these coatings on gas barrier characteristics have been investigated. The temperature during light irradiation has a large effect on the coating’s molecular structure and gas barrier characteristics. When irradiation was performed at 100℃, the polysilazane coating transformed into a silica coating, and a compact silica coating at a much lower temperature than with heat treatment alone was produced. Surface irregularities in the vapor-deposited silica coating were smoothed out by the formation of a polysilazane coating, which was transformed into a compact silica coating when irradiated with light, resulting in a significant improvement in the gas barrier characteristics. The water vapor permeability of the thin coating irradiated with excimer light at 100℃ showed only 0.04 g/m2•day (40℃, 90% RH). According to the results of investigation of temperature variation of water-vapor permeability, it is inferred that the developed film has an excellent gas barrier value, namely, 4.90 × 10–4 g/m2•day at 25℃. This gas barrier coated PET film is transparent and flexible, and can be used in the fabrication of flexible electronics. Also, the proposed fabrication method effectively provides a simple low-cost and low-temperature fabrication technique without the need for high vacuum facility.
文摘Flexible electronics have been recently paid much attention. A flexible substrate (Organic resin film) is indispensable component for flexible devices. Though PET film is low-cost organic film, low heat-resistance of PET film limits its application as a flexible device substrate. We have developed heat-resistant PET which does not deteriorate even at 190°C heat treatment for one hour. An excimer light was irradiated onto a polysi-lazane (PHPS: perhydropolysilane)-coated film to form a dense silicon-dioxide (SiO2) layer on a PET film, and the heat-resistance property of the formed film was examined. Changes of surface state and cross-sectional structure of the formed film due to heat treatment were investigated by scanning electron microscope (SEM) and transmission electron microscope (TEM). Compared to normal PET, which is deteriorated and whitened by heat treatment of about 110°C - 120°C, the SiO2-coated PET film maintains transparency and does not deteriorate after heat treatment at 180°C - 190°C for one hour. This high heat resistance is due to a dense SiO2 film formed on the surface that prevents surface precipitation and crystallization of low-molecular-weight oligomers (which are the cause of thermal degradation of PET). It is expected that enhancing the heat resistance of PET—which has high versatility and low cost—to about 180°C to 190°C will allow SiO2-film-coated PET to be developed as a film substrate for flexible devices.
基金supported by the Natural Science Foundation of China(No.U22A20129)the National Science and Technology Major Project(No.2017-VI-0002-0072)+2 种基金the National Key Research and Development Program of China(No.2018YFB1106600)the Fundamental Research Funds for the Central Universities(No.WK5290000003)the Students’Innovation and Entrepreneurship Foundation of USTC(Nos.CY2022G10 and CY2022C24)。
文摘High strength and high toughness are mutually exclusive in structural materials.In ceramic materials,increasing toughness usually depends on the introduction of a ductile phase that reduces the strength and high-temperature stability of the material.In this work,vat photopolymerization 3D printing technology was used to achieve toughening of ceramic composite material.The friction sliding of the 3D-printed ceramic macrolayer structure results in effective energy dissipation and redistribution of strain in the whole structure,and macroscale toughening of the ceramic material is realized.In addition,the bridging and elongation of the crack in situ amorphous ceramic whiskers were significant microscopic toughening results,coupled with the toughening of the crack tip of nano-ZrO_(2).Multiscale collaborative toughening methods based on 3D-printed ceramics should find wide applications for materials in service at extreme high temperatures.
