Polypropylene（PP）/ethylene-octene copolymer（POE） blends were prepared with a twin-screw extruder.Their dynamic mechanical behavior were systematically investigated.The results show that PP/POE blends are heterogen...Polypropylene（PP）/ethylene-octene copolymer（POE） blends were prepared with a twin-screw extruder.Their dynamic mechanical behavior were systematically investigated.The results show that PP/POE blends are heterogeneities with a partial compatible two-phase structure,the glass transition temperature of PP phases in the blends tends to shift towards high temperature with increasing the POE content,and the glass transition temperature of POE phases shifts towards the low temperature with increasing the PP content.The Kerner＇s dispersed phase model and co-continuous phase model can reasonably predict the visco-elasticity of PP/POE blends with different compositions.Additionally,the morphological structure of the blends can be estimated via comparing the predicted DMA behavior with the experimental data.展开更多
The attainment of a better understanding and improvement of electrical properties of ternary blend is a task of particular scientific and economic importance. Ternary films of Poly (methylmethacrylate), Poly (ethlymat...The attainment of a better understanding and improvement of electrical properties of ternary blend is a task of particular scientific and economic importance. Ternary films of Poly (methylmethacrylate), Poly (ethlymathacrylate) and poly (vinlylidenefluoride) were prepared using solution cast technique. Thereafter, to study the hetro charges, homo-charges and interfacial charge formation in ternary system, the short circuit thermally stimulated discharge current (SC-TSDC) measurements were carried out on bilaterally metallized electrets. The ternary blend samples taken for the present investigations are hetrogeneous system involving three polymers differing in their conduction behaviour and dielectric property. Thus, unequal ohmic conduction currents arriving at the interface are expected to result in accumulation of charges at the interface or the Maxwell-Wagner effect. Clearly the Maxwell Wagner effect is expected to contribute discernibly to the observed TSDC’s of the ternary blends. The PMMA: PEMA: PVDF:: 100:100:50 blend exhibits highest tendency while 100:50:100 the least, towards the anomalous current flow. Moreover, the conductivity of 100: 100: 50 is found to be more and, therefore, a large amount of homocharge is injected leading to anomalous current.展开更多
In this study, the adsorptive properties of L-menthol, moisture vapor transmission rate, and mechanical properties of poly (ethylene terephthalate) (PET), polypropylene (PP), and their blends were evaluated in contain...In this study, the adsorptive properties of L-menthol, moisture vapor transmission rate, and mechanical properties of poly (ethylene terephthalate) (PET), polypropylene (PP), and their blends were evaluated in containers fabricated by injection molding without a compatibilizing agent. These containers intended to hold pharmaceutical solutions containing lipophilic chemicals such as L-menthol. By the addition of a small amount of PP, the moisture barrier properties of PET were effectively improved, but its anti-adsorptive property was reduced. The strength of the PET/PP blends was reduced, but some PET/PP blends were still able to bear the experimental load required for application in eye-drop containers. PET/PP = 9/1 and PET/PP = 8/2 were found to be most applicable for using in the fabrication of containers for medicinal solutions.展开更多
For evaluation of the rheological and mechanical properties of highly filled wood plastic composites （WPCs）, polypropylene/polyethylene （PP/PE） blends were grafted with maleic anhydride （MAH） to enhance the inte...For evaluation of the rheological and mechanical properties of highly filled wood plastic composites （WPCs）, polypropylene/polyethylene （PP/PE） blends were grafted with maleic anhydride （MAH） to enhance the interfacial adhesion between wood fiber and matrix. WPCs were prepared from wood fiber up to 60 wt.% and modified PP/PE was blended by extrusion. The rheological properties were studied by using dynamic measurement. According to the strain sweep test, the linear viscoelastic region of composites in the melt was determined. The result showed that the storage modulus was independent of the strain at low strain region （〈0.1%）. The frequency sweep resuits indicated that all composites exhibited shear thinning behavior, and both the storage modulus and complex viscosity of MAH modified composites were decreased comparing to those unmodified. Flexural properties and impact strength of the prepared WPCs were measured according to the relevant standard specifications. The flexural and impact strength of the manufactured composites significantly increased and reached a maximum when MAH dosage was 1.0 wt%, whereas the flexural modulus after an initial decreased, also increased with MAH dosage. The increase in mechanical properties indicated that the presence of anhydride groups enhanced the interracial adhesion between wood fiber and PP/PE blends.展开更多
Metallocene-catalyzed linear low-density polyethylene/polypropylene （mLLDPE/PP） blends were prepared by ultrasonic extrusion in this work. Their extrusion processing behaviors were estimated by online measured data,...Metallocene-catalyzed linear low-density polyethylene/polypropylene （mLLDPE/PP） blends were prepared by ultrasonic extrusion in this work. Their extrusion processing behaviors were estimated by online measured data, such as the die pressure and flow rate. Crystallization and mechanical properties of the blends were also investigated. The results show that the addition of PP improves the processing behaviors of mLLDPE, but has little effect on its mechanical properties. On the other hand, the addition of mLLDPE improves the impact strength of PP, but has little effect on its processing behavior. The processing behaviors and mechanical properties of mLLDPE/PP blends get further improved due to the presence of ultrasonic oscillation during extrusion. Compared with PP-rich blends, the apparent viscosity drop of mLLDPE-rich blends is more sensitive to ultrasonic oscillation. The ultrasonic oscillation affects the crystal nucleation, while barely the other crystalline behaviors of the blends.展开更多
In this work, polypropylene (PP)/polystyrene (PS) blends with different organoclay concentrations were prepared via melt compounding. Differing from the results of previous reports, the organoclay platelets are mostly...In this work, polypropylene (PP)/polystyrene (PS) blends with different organoclay concentrations were prepared via melt compounding. Differing from the results of previous reports, the organoclay platelets are mostly located in the dispersed PS phase instead of the interface. The dimensions of the dispersed PS droplets are greatly reduced and apparent compatibilization effect still exists, which cannot be explained by the traditional compatibilization mechanism. A novel compatibilization mecha- nism, "cutting" to apparently compatibilize the immiscible PP/PS blends was proposed. The organoclay platelets tend to form a special "knife-like structure" in the PS domain under the shear stress of the continuous PP phase during compounding. The "clay knife" can split the dispersed PS domain apart and lead to the dramatic reduction of the dispersed domain size.展开更多
Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCVMgCl2 supported catalyst. A solution of ben...Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCVMgCl2 supported catalyst. A solution of benzoyl peroxide (BPO)/maleic anhydride (MAH)/xylene (interfacial reagent) or BPO/MAH/St (comonomer) was absorbed onto the PE/PP in- reactor blend granules, and solid phase graft polymerization of MAH on PE/PP was conducted. The amount of grafted MAH on PE/PP was measured through chemical titration. The results showed that solid phase graft polymerization of MAH in PE/PP in-reactor blend granules produced graft copolymer with high amount of grafted MAH, and the amount of grafted MAH was raised slightly when St was introduced as comonomer. The graft in-reactor blend was fractionated into five fractions through temperature-gradient extraction fractionation (TGEF), and the fractions were analyzed by FTIR. The results revealed that MAH is mainly grafted on the PE segments, whereas MAH was predominantly grafted on the PP segments when St was present in the graft polymerization system. In addition, the final product is still in the form of regular spherical granules, which is beneficial for industrial processing.展开更多
Polypropylene superfine fibers or cell porous fibers were prepared from the bi-component blend fibers of polypropylene/easlly hydro-degraded polyester(PP/EHDPET)by alkaline hydrolysis process. EHDPET is a kind of copo...Polypropylene superfine fibers or cell porous fibers were prepared from the bi-component blend fibers of polypropylene/easlly hydro-degraded polyester(PP/EHDPET)by alkaline hydrolysis process. EHDPET is a kind of copolyester that can be rapidly hydro-degraded in the hot alkaline solution. This paper discussed the kinetics of alkaline hydrolysis of EHDPET, and the effect of catalyst, bulk ratio and the content of polypropylene grafted maleic anhydride (PP-g-MAH) on the alkaline hydrolysis process. Meanwhile, the morphological change of the outer surface of blend fibers during this process was also investigated by the technology of scanning electron microscope (SEM).展开更多
The aim of this work was to study the influence of CaCO3 in both tensile and flexural mechanical properties of a PET(polyethylene terephthalate)/PP(polypropylene).Four compositions of PET/PP/CaCO3 blend were prepared ...The aim of this work was to study the influence of CaCO3 in both tensile and flexural mechanical properties of a PET(polyethylene terephthalate)/PP(polypropylene).Four compositions of PET/PP/CaCO3 blend were prepared by injection molding with CaCO3 content of 0,2,4 and 6 wt%.The samples were cut according to the ASTM(American Society for Testing and Materials)standard and tested by using universal testing equipment.The results show that the mechanical properties of the PET/PP/CaCO3 composites with 2%and 4 wt%of CaCO3 composition were better than that of the PET/PP composites.While the content of CaCO3 is 6 wt%,the serious phase separation between PET and PP resulted in poor mechanical properties of the PET/PP/CaCO3 samples.This study shows that CaCO3 has played a role to improve the tensile and flexural properties of the mixing product if it is present only in a small amount.展开更多
Blends of polypropylene(PP) and low density polyethylene(LDPE) have been crystallized to form open structures(“cluster spherulites”) where the droplets of the minority PP are bridged by PP lamellae which have grown ...Blends of polypropylene(PP) and low density polyethylene(LDPE) have been crystallized to form open structures(“cluster spherulites”) where the droplets of the minority PP are bridged by PP lamellae which have grown in the LDPE rich matrix. These are studied by permanganic etching followed by electron and optical microscopies. Two similar PP types are compared, one synthesized with Ziegler Natta catalyst and one with metallocene catalyst. The metallocene catalysed material crystallized much more slowly due to the presence of regio defects in the chains, even though the overall concentration of tacticity defects in the Ziegler Natta material is much higher. A mechanism involving reversal of helical direction at the regio defect interfering with the regular chain packing in the crystal is suggested. Growth of “cluster spherulites” is faster in regions where low molecular weight material is concentrated. It is slower where droplets are larger, and this is attributed to competition between PP lamellar growth in the matrix and diffusion of PP to already crystallized droplets.展开更多
In the present work, magnetite (Fe<sub>3</sub>O<sub>4</sub>) nanoparticles have been prepared by a simple chemical method. Polymer nanocomposites based on the blend between poly vinylamine fluo...In the present work, magnetite (Fe<sub>3</sub>O<sub>4</sub>) nanoparticles have been prepared by a simple chemical method. Polymer nanocomposites based on the blend between poly vinylamine fluoride (PVDF) and (methyl methacrylate) (PMMA) doped with different concentrations of Fe<sub>3</sub>O<sub>4</sub> nanoparticles have been prepared. The structural, optical, and magnetization properties of the nanocomposite samples were studied using suitable techniques. The X-ray study reflected that the cubic spinal structure of pure Fe<sub>3</sub>O<sub>4</sub> crystal. No small peaks or ripples were found in the X-ray spectra, conforming to good dispersion of Fe<sub>3</sub>O<sub>4</sub> within PVDF/PMMA matrices. The FT-IR analysis demonstrated the miscibility between the PVDF and PMMA blend with the interaction between the polymer blend and Fe<sub>3</sub>O<sub>4</sub>. The values of the band gap from UV-Vis study were decreased up to 4.21 eV, 3.01 eV for direct and indirect measurements, respectively. The magnetization was measured as a function of the applied magnetic field in the range of −2000 - 2000 Oersted. The curves of the magnetization indicated a paramagnetic behavior of pure Fe<sub>3</sub>O<sub>4</sub> nanoparticles and PVDF/PMMA-Fe<sub>3</sub>O<sub>4</sub> nanocomposites. The values of saturation magnetization for pure Fe<sub>3</sub>O<sub>4</sub> are nearly 75 emu/g, exhibiting a paramagnetic behavior, and it is decreased with the increase of Fe<sub>3</sub>O<sub>4</sub> content.展开更多
基金Supported by the National Natural Science Foundation of China(No.20490220)Open Fund of State Key Laboratory of Plastic Forming Simulation and Die & Mould Technology,China(No.05-10)+1 种基金Open Fund of Hubei Key Laboratory of Materials Chemistry and Service FailureProgram for New Century Excellent Talents in Universities of China(No.NCET-05-0640)
文摘Polypropylene（PP）/ethylene-octene copolymer（POE） blends were prepared with a twin-screw extruder.Their dynamic mechanical behavior were systematically investigated.The results show that PP/POE blends are heterogeneities with a partial compatible two-phase structure,the glass transition temperature of PP phases in the blends tends to shift towards high temperature with increasing the POE content,and the glass transition temperature of POE phases shifts towards the low temperature with increasing the PP content.The Kerner＇s dispersed phase model and co-continuous phase model can reasonably predict the visco-elasticity of PP/POE blends with different compositions.Additionally,the morphological structure of the blends can be estimated via comparing the predicted DMA behavior with the experimental data.
文摘The attainment of a better understanding and improvement of electrical properties of ternary blend is a task of particular scientific and economic importance. Ternary films of Poly (methylmethacrylate), Poly (ethlymathacrylate) and poly (vinlylidenefluoride) were prepared using solution cast technique. Thereafter, to study the hetro charges, homo-charges and interfacial charge formation in ternary system, the short circuit thermally stimulated discharge current (SC-TSDC) measurements were carried out on bilaterally metallized electrets. The ternary blend samples taken for the present investigations are hetrogeneous system involving three polymers differing in their conduction behaviour and dielectric property. Thus, unequal ohmic conduction currents arriving at the interface are expected to result in accumulation of charges at the interface or the Maxwell-Wagner effect. Clearly the Maxwell Wagner effect is expected to contribute discernibly to the observed TSDC’s of the ternary blends. The PMMA: PEMA: PVDF:: 100:100:50 blend exhibits highest tendency while 100:50:100 the least, towards the anomalous current flow. Moreover, the conductivity of 100: 100: 50 is found to be more and, therefore, a large amount of homocharge is injected leading to anomalous current.
文摘In this study, the adsorptive properties of L-menthol, moisture vapor transmission rate, and mechanical properties of poly (ethylene terephthalate) (PET), polypropylene (PP), and their blends were evaluated in containers fabricated by injection molding without a compatibilizing agent. These containers intended to hold pharmaceutical solutions containing lipophilic chemicals such as L-menthol. By the addition of a small amount of PP, the moisture barrier properties of PET were effectively improved, but its anti-adsorptive property was reduced. The strength of the PET/PP blends was reduced, but some PET/PP blends were still able to bear the experimental load required for application in eye-drop containers. PET/PP = 9/1 and PET/PP = 8/2 were found to be most applicable for using in the fabrication of containers for medicinal solutions.
文摘For evaluation of the rheological and mechanical properties of highly filled wood plastic composites （WPCs）, polypropylene/polyethylene （PP/PE） blends were grafted with maleic anhydride （MAH） to enhance the interfacial adhesion between wood fiber and matrix. WPCs were prepared from wood fiber up to 60 wt.% and modified PP/PE was blended by extrusion. The rheological properties were studied by using dynamic measurement. According to the strain sweep test, the linear viscoelastic region of composites in the melt was determined. The result showed that the storage modulus was independent of the strain at low strain region （〈0.1%）. The frequency sweep resuits indicated that all composites exhibited shear thinning behavior, and both the storage modulus and complex viscosity of MAH modified composites were decreased comparing to those unmodified. Flexural properties and impact strength of the prepared WPCs were measured according to the relevant standard specifications. The flexural and impact strength of the manufactured composites significantly increased and reached a maximum when MAH dosage was 1.0 wt%, whereas the flexural modulus after an initial decreased, also increased with MAH dosage. The increase in mechanical properties indicated that the presence of anhydride groups enhanced the interracial adhesion between wood fiber and PP/PE blends.
基金This work was financially supported by the Special Funds for Major State Basic Research Projects of China (No.2005CB623800)the National Natural Science Foundation of China (No. 20374037)the Open Foundation of Key Laboratory of Rubber-plastics (QUST),Ministry of Education, China and the Foundation for Youth of Sichuan University
文摘Metallocene-catalyzed linear low-density polyethylene/polypropylene （mLLDPE/PP） blends were prepared by ultrasonic extrusion in this work. Their extrusion processing behaviors were estimated by online measured data, such as the die pressure and flow rate. Crystallization and mechanical properties of the blends were also investigated. The results show that the addition of PP improves the processing behaviors of mLLDPE, but has little effect on its mechanical properties. On the other hand, the addition of mLLDPE improves the impact strength of PP, but has little effect on its processing behavior. The processing behaviors and mechanical properties of mLLDPE/PP blends get further improved due to the presence of ultrasonic oscillation during extrusion. Compared with PP-rich blends, the apparent viscosity drop of mLLDPE-rich blends is more sensitive to ultrasonic oscillation. The ultrasonic oscillation affects the crystal nucleation, while barely the other crystalline behaviors of the blends.
文摘In this work, polypropylene (PP)/polystyrene (PS) blends with different organoclay concentrations were prepared via melt compounding. Differing from the results of previous reports, the organoclay platelets are mostly located in the dispersed PS phase instead of the interface. The dimensions of the dispersed PS droplets are greatly reduced and apparent compatibilization effect still exists, which cannot be explained by the traditional compatibilization mechanism. A novel compatibilization mecha- nism, "cutting" to apparently compatibilize the immiscible PP/PS blends was proposed. The organoclay platelets tend to form a special "knife-like structure" in the PS domain under the shear stress of the continuous PP phase during compounding. The "clay knife" can split the dispersed PS domain apart and lead to the dramatic reduction of the dispersed domain size.
基金This work was supported by the Special Fund for Major State Basic Research Projects (Grant no. G1999064803).
文摘Spherical polyethylene/polypropylene (PE/PP) in-reactor blend granules with various ethylene/propylene molar ratios and high porosity were synthesized using a high yield TiCVMgCl2 supported catalyst. A solution of benzoyl peroxide (BPO)/maleic anhydride (MAH)/xylene (interfacial reagent) or BPO/MAH/St (comonomer) was absorbed onto the PE/PP in- reactor blend granules, and solid phase graft polymerization of MAH on PE/PP was conducted. The amount of grafted MAH on PE/PP was measured through chemical titration. The results showed that solid phase graft polymerization of MAH in PE/PP in-reactor blend granules produced graft copolymer with high amount of grafted MAH, and the amount of grafted MAH was raised slightly when St was introduced as comonomer. The graft in-reactor blend was fractionated into five fractions through temperature-gradient extraction fractionation (TGEF), and the fractions were analyzed by FTIR. The results revealed that MAH is mainly grafted on the PE segments, whereas MAH was predominantly grafted on the PP segments when St was present in the graft polymerization system. In addition, the final product is still in the form of regular spherical granules, which is beneficial for industrial processing.
文摘Polypropylene superfine fibers or cell porous fibers were prepared from the bi-component blend fibers of polypropylene/easlly hydro-degraded polyester(PP/EHDPET)by alkaline hydrolysis process. EHDPET is a kind of copolyester that can be rapidly hydro-degraded in the hot alkaline solution. This paper discussed the kinetics of alkaline hydrolysis of EHDPET, and the effect of catalyst, bulk ratio and the content of polypropylene grafted maleic anhydride (PP-g-MAH) on the alkaline hydrolysis process. Meanwhile, the morphological change of the outer surface of blend fibers during this process was also investigated by the technology of scanning electron microscope (SEM).
文摘The aim of this work was to study the influence of CaCO3 in both tensile and flexural mechanical properties of a PET(polyethylene terephthalate)/PP(polypropylene).Four compositions of PET/PP/CaCO3 blend were prepared by injection molding with CaCO3 content of 0,2,4 and 6 wt%.The samples were cut according to the ASTM(American Society for Testing and Materials)standard and tested by using universal testing equipment.The results show that the mechanical properties of the PET/PP/CaCO3 composites with 2%and 4 wt%of CaCO3 composition were better than that of the PET/PP composites.While the content of CaCO3 is 6 wt%,the serious phase separation between PET and PP resulted in poor mechanical properties of the PET/PP/CaCO3 samples.This study shows that CaCO3 has played a role to improve the tensile and flexural properties of the mixing product if it is present only in a small amount.
文摘Blends of polypropylene(PP) and low density polyethylene(LDPE) have been crystallized to form open structures(“cluster spherulites”) where the droplets of the minority PP are bridged by PP lamellae which have grown in the LDPE rich matrix. These are studied by permanganic etching followed by electron and optical microscopies. Two similar PP types are compared, one synthesized with Ziegler Natta catalyst and one with metallocene catalyst. The metallocene catalysed material crystallized much more slowly due to the presence of regio defects in the chains, even though the overall concentration of tacticity defects in the Ziegler Natta material is much higher. A mechanism involving reversal of helical direction at the regio defect interfering with the regular chain packing in the crystal is suggested. Growth of “cluster spherulites” is faster in regions where low molecular weight material is concentrated. It is slower where droplets are larger, and this is attributed to competition between PP lamellar growth in the matrix and diffusion of PP to already crystallized droplets.
文摘In the present work, magnetite (Fe<sub>3</sub>O<sub>4</sub>) nanoparticles have been prepared by a simple chemical method. Polymer nanocomposites based on the blend between poly vinylamine fluoride (PVDF) and (methyl methacrylate) (PMMA) doped with different concentrations of Fe<sub>3</sub>O<sub>4</sub> nanoparticles have been prepared. The structural, optical, and magnetization properties of the nanocomposite samples were studied using suitable techniques. The X-ray study reflected that the cubic spinal structure of pure Fe<sub>3</sub>O<sub>4</sub> crystal. No small peaks or ripples were found in the X-ray spectra, conforming to good dispersion of Fe<sub>3</sub>O<sub>4</sub> within PVDF/PMMA matrices. The FT-IR analysis demonstrated the miscibility between the PVDF and PMMA blend with the interaction between the polymer blend and Fe<sub>3</sub>O<sub>4</sub>. The values of the band gap from UV-Vis study were decreased up to 4.21 eV, 3.01 eV for direct and indirect measurements, respectively. The magnetization was measured as a function of the applied magnetic field in the range of −2000 - 2000 Oersted. The curves of the magnetization indicated a paramagnetic behavior of pure Fe<sub>3</sub>O<sub>4</sub> nanoparticles and PVDF/PMMA-Fe<sub>3</sub>O<sub>4</sub> nanocomposites. The values of saturation magnetization for pure Fe<sub>3</sub>O<sub>4</sub> are nearly 75 emu/g, exhibiting a paramagnetic behavior, and it is decreased with the increase of Fe<sub>3</sub>O<sub>4</sub> content.
