An Overview of 3D Thin Shell Textile Preforms

The automobiles, aircraft, and lightweight industries continuously demand thin near-net-shape preforms just out-of-machine as close to the final shape. This study addresses the possibilities of 3D thin shell textile preform as the solution of lightweight reinforcement in various applications. Investigation into the development of 3D thin shells has led to different manufacturing processes. However, 3D thin shell preforms are mostly made by weaving and knitting, but nonwoven, winding, and/or layup techniques have been reported for over a decade. Owing to the complex thin shell manufacturing processes, they are not similar to the conventional methods. The different 3D thin shell preforms can extend the opportunities for new applications in various technical fields. This study presents existing research gaps and a few potential issues to be solved regarding 3D thin shell preforms in the near future.

An Overview of 3D Thin Shell Textile Preforms

The automobiles, aircraft, and lightweight industries continuously demand thin near-net-shape preforms just out-of-machine as close to the final shape. This study addresses the possibilities of 3D thin shell textile preform as the solution of lightweight reinforcement in various applications. Investigation into the development of 3D thin shells has led to different manufacturing processes. However, 3D thin shell preforms are mostly made by weaving and knitting, but nonwoven, winding, and/or layup techniques have been reported for over a decade. Owing to the complex thin shell manufacturing processes, they are not similar to the conventional methods. The different 3D thin shell preforms can extend the opportunities for new applications in various technical fields. This study presents existing research gaps and a few potential issues to be solved regarding 3D thin shell preforms in the near future.

Sensitivity Analysis Based Multiple Objective Preform Die Shape Optimal Design in Metal Forging

The multiple objective preform design optimization was put forward. The final forging＇s shape and deformation uniformity were considered in the multiple objective. The objective is to optimize the shape and the deformation uniformity of the final forging at the same time so that a more high integrate quality of the final forging can be obtained. The total objective was assembled by the shape and uniformity objective using the weight adding method. The preform die shape is presented by cubic B-spline curves. The control points of B-spline curves are used as the design variables. The forms of the total objective function, shape and uniformity sub-objective function are given. The sensitivities of the total objective function and the sub-objective functions with respect to the design variables are developed. Using this method, the preform die shape of an H-shaped forging process is optimally designed. The optimization results are very satisfactory.

Insight into the preformed albumin corona on in vitro and in vivo performances of albumin-selective nanoparticles

Preformed albumin corona of albumin-nonselective nanoparticles(NPs)is widely exploited to inhibit the unavoidable protein adsorption upon intravenous administration.However,very few studies have concerned the preformed albumin corona of albumin-selective NPs.Herein,we report a novel type of albumin-selective NPs by decorating 6-maleimidocaproyl polyethylene glycol stearate(SA)onto PLGA NPs(SP NPs)surface,taking albuminnonselective PLGA NPs as control.PLGA NPs and SP NPs were prepared by emulsion-solvent evaporation method and the resultant NPs were in spherical shape with an average diameter around 180 nm.The corresponding albumin-coating PLGA NPs(PLGA@BSA NPs)and albumin-coating SP NPs(SP@BSA NPs)were formulated by incubating SP NPs or PLGA NPs with bovine serum albumin solution,respectively.The impact of albumin corona on particle characteristics,stability,photothermal effect,cytotoxicity,cell uptake,spheroid penetration and pharmacokinetics was investigated.In line with previous findings of preformed albumin coating,PLGA@BSA NPs exhibited higher stability,cytotoxicity,cell internalization and spheroid penetration performances in vitro,and longer blood circulation time in vivo than those of albumin-nonselective PLGA NPs,but albumin-selective SP NPs is capable of achieving a comparable in vitro and in vivo performances with both SP@BSA NPs and PLGA@BSA NPs.Our results demonstrate that SA decorated albumin-selective NPs pave a versatile avenue for optimizing nanoparticulate delivery without preformed albumin corona.

Effect of initiation manners on the scattering characteristics of semi-preformed fragment warhead

The lethality of a semi-preformed fragment warhead is closely related to the expand velocity and spatial distribution of the fragments from ruptured metal casing. The topic of how to improve the utilization of charge of have been drawing great attention from researchers and designer in this filed. In present paper,in order to investigate the influence of charge initiation manners on the scattering characteristics of semi-preformed fragment warhead, the numerical simulations and experimental test are conducted.Firstly, the influence of grid density on numerical results is investigated, and a proper numerical model with relatively high accuracy and effectiveness is determined. Then. numerical simulations of three kinds of different initiation position of a semi-preformed fragment warhead are carried out. An experimental test of the explosion of a semi-preformed fragment warhead is carried out. By comparing and analyzing the numerical results and experimental data, it is found that the initiation manners have great influence on scattering characteristics of semi-preformed fragment warhead. The researcher work of this paper would provide an effective alternative method to optimize the design of warhead.

Optimal Preform Die Design through Controlling Deformation Uniformity in Metal Forging

A finite element based sensitivity analysis method for preform die shape design in metal forging is developed. The optimization goal is to obtain more uniform deformation within the final forging by controlling the deformation uniformity. The objective function expressed by the effective strain is constructed. The sensitivity equations of the objective function, elemental volume, elemental effective strain rate and the elemental strain rate with respect to the design variables are constituted. The preform die shapes of an H-shaped forging process in axisymmetric deformation are designed using this method.

Mechanical Properties of the Cured Laminates on the Hot-press Tackified Preforms in Vacuum Assisted Resin Transfer Molding

A hot-press tackified preform was used to improve the uniformity of the laminates thickness and the mechanical properties of the obtained laminates were studied using vacuum assisted resin transfer molding（VARTM）. Two modified preforms were prepared under 0.1 and 0.6 MPa in an autoclave and then were used to fabricate the laminates via VARTM. Permeability and thickness distribution of the laminates were obtained by using a special device. Moreover, the tensile and compressive strengths of the obtained laminates were studied and compared with the unmodified ones. Results show that the tackified laminates present a maximum and minimum thickness under 0.1 and 0.6 MPa, respectively. The thicknesses and in-plane permeability of the tackified laminates, with better thickness uniformity, are significantly decreased compared with that of the unmodified cases, while the tensile and compressive strengths of the tackified laminates are improved obviously. Results show that the mechanical property of the tackified laminates prepared by hotpressing at 0.1 MPa is better than that processed at 0.6 MPa.

Design,preparation,and structure of particle preforms for Si_3N_(4(P))/Si_3N_4 radome composites prepared using chemical vapor infiltration process

A particle preform was designed and prepared by conglomerating and cold-pressed process, which was condensed by chemical vapor infiltration （CVI） process to fabricate silicon nitride particles reinforced silicon nitride composites. The conglomerations are of almost sphericity after conglomerated. There are large pores among the conglomerations and small pores within themselves in the preform according to the design and the test of pore size distribution. The pore size of the preform is characterized by a double-peak distribution. The pore size distribution is influenced by conglomeration size. Large pores among the conglomerations still exist after infiltrated Si3N4 matrix. The conglomerations, however, are very compact. The CVI Si3N4 looks like cauliflowershaped structure. 2008 University of Science and Technology Beijing. All rights reserved.

Spinel Castables for Steel Ladle Lining:In-Situ Versus Preformed

The paper discusses the difference in the formulation concepts of alumina - spinel （spinel containing ） and alumina - magnesia （ spin, el forming） castables and the influence on their physical properties. The individual property profile is discussed with respect to the requirements of refactory lining materials for the different zones of a steel ladle.

Development and Characterization of Fe-Based Friction Material Made by Hot Powder Preform Forging for Low Duty Applications

This present paper investigates the friction and wear properties of friction material developed by ‘Hot Powder Preform Forging’ technique. The conventional technique to manufacture Metallo-ceramic brake pads was successfully and economically tried to replace the above process. Compacting and sintering technology suffers from certain major limitations such as inadequate joining of friction element with backing plate, poor density levels achieved in friction element owing to limited application of pressure during compacting, poor thermal conductivity due to high levels of porosity in the product, poor strength due to segregation of the impurities along prior particle boundaries (PPB’s) and, wide variations in final characteristics due to large number of variables involved. In contrast to these limitations, the present technique can offer brake pads of much simpler chemistry but with improved performance on account of simultaneous application of pressure and temperature and with better control of variables. Fade and recovery studies were carried out on a Krauss machine tester following the Economic Commission for Europe Regulation for replacement brake linings (ECE R-90). μfade, μrecovery, μperformance, % age fade , % age recovery & temperature rise lie within the range for friction materials used for low duty applications. The mechanical properties of these materials were characterized using ASTM standards.

Model of Preformed Hole-Pairs in c-Axis Transport in Cuprate Superconductors

Model of hole-pairs in electrical transport along ab plane in cuprate superconductors has already been proposed. It has been found to be in the shape of 3dx2–y2 orbital of an electron in an atom. This time, model of hole-pairs in transport along c-axis in cuprate superconductors is proposed. In ab-plane, hole-pairs are formed along CuO2 plane;one hole-pair covering 9 - 10 two dimensional CuO2 unit cells in 3dx2–y2 configuration. In the investigation of c-axis hole-pairs, cuprate superconductors have been sub-divided into three categories depending on the number of CuO2 planes/formula unit. There is a little different treatment for finding out the order parameter in each category. Coherence lengths along ab-planes are of the order of a few tens of Angstroms, whereas along c-axis, they are less than even their a-, b-lattice constants. In cuprates with 2 or 3 CuO2 planes, the order parameter is of 3dz2–x2 type in zx-plane with lobes along both the axes much constrained. For cuprates with a single CuO2 layer, the order parameter is of 3dx2–y2 type, but its dimensions are less than a-, b-lattice constants.

Properties of SiC Particulate Preforms Based on Different Pore-forming Agents and Bonding Methods for Making SiC/Al Composites

The preforms with high SiC volume fraction （〉50%） were successfully fabricated by two bonding methods. Moreover, the dimensional change, compressive strength, and microstructure of SiC preforms were investigated, and the bonding mechanism among SiC particulates in preforms was also discussed. Results show that, after heating to 1 100 ~C and holding for 2 h, a uniform and interconnected structure in the SiC preforms can be obtained by using starch, stearic acid, and graphite respectively as the pore-forming agents, which benefits the subsequent infiltration by the molten metals. More neck-like-jointing among SiC particulate by using graphite as the pore-forming agent improves the dimensional accuracy and compressive strength of the preform. Besides, the properties of the preforms by the binder bonding are better than those by the oxidation bonding, which is mainly because the mixed neck-like-jointing and binder at high temperature provide effective bonding together.

α preformation and penetration probability for heavy nuclei

The α preformation factor and penetration probability have been analyzed for even-even nuclei of Po, Rn, Ra using experimental released energies and α decay half-lives in the frame of the double folding model. It is shown that N = 126 is a neutron magic number from α preformation and shell effects play an important role in α preformation, The closer the nucleon number is to the magic number, the more difficult α formation in the parent nucleus is. The preformation factor can supply information on the nuclear structure and the penetration probability mainly determines α decay half-life.

Reactivity of Human Preformed Natural Antibodies with Various Porcine Pancreatic Cells

The reactivity of human preformed natural antibodies (PNAbs) with various porcine pancreatic cells and its isotypes was investigated. Eighteen serum samples from patients with insulin dependent diabetes mellitus (IDDM) and 20 serum samples from healthy human subjects were collected. The frozen sections of the pig pancreas were incubated with these sera, and subsequently incubated with FITC conjugated goat antihuman IgG and IgM monoclonal antibodies. The reactivity of human PNAbs with various porcine pancreatic cells was determined by indirect immunofluorescence staining technique. The results showed that 55.6 % of IDDM patients and 55.0 % of healthy human individuals contained PNAbs against porcine endocrine cells. However, the percentage of strongly reacting sera in the patient group was significantly increased as compared with that in the control group. All used sera from IDDM patients and 95 % of sera from healthy controls could react to one or more of the various pancreatic cell types, including: endocrine cells, exocrine cells, vascular endothelial cells, ductal epithelial cells and macrophages. The isotypes of PNAbs contained both IgG and IgM. In view of strongly positive reactivity of PNAbs with various porcine pancreatic cells, pretransplantly cross matching test and graft pretreatment may be necessary for survival of islet transplants.

A NEW APPROACH TO MANUFACTURING 3D WOVEN PREFORMS USED FOR STRUCTURAL COMPOSITES

The manufacturing of three-dimensional textile preforms used for composites started to re-ceive much attention in the last decade.The major barriers to accelerating the transition from thelamination of two-dimensional fabrics to manufacturing integral three-dimensional near-netshaped textile preforms are high cost and database deficiency.To reduce the cost of weaving three-dimensional preforms,and make full use of the potential of conventional looms,a rig was designedwhich can convert two-dimensional woven fabric to particular three-dimensional preforms wherethe yarn is orientated in the directions of maximum stress.

Effect of preforming on the formability of TRIP steel sheet forming processes

In this study,the formability of transformation-induced plasticity (TRIP) steel is studied during deep-drawing processes with preforming.The effects of preforming on theminimum thickness of can are investigated with a constitutive model accompanying strain-induced martensite transformation in prestrain condition.The constitutive model has been implemented into ABAQUS/UMAT for analysis of TRIP steel-forming processes.The results show that preforming slightly influences the thickness uniformity of TRIP steel in forming.

Degradable preformed particle gel as temporary plugging agent for low-temperature unconventional petroleum reservoirs:Effect of molecular weight of the cross-linking agent

The development of unconventional petroleum resources has gradually become an important succession for increasing oil production.However,the related engineers and researchers are paying more and more attention to the application of temporary plugging agents(TPAs)for their efficient development.TPAs can expand the stimulated reservoir volume(SRV)and facilitate the flow of oil and gas to the bottom of the well.Particle-gels used as temporary plugging agents have the characteristics of the simple injection process,good deformation,high plugging strength,and complete self-degradation performance,which have been widely applied in recent years.In this paper,five samples of DPPG polymerized by different molecular weights of cross-linking agents were prepared.In addition,infrared spectroscopy analysis,differential calorimetry scanning(DSC)analysis,static particle gel swelling and degradation performance evaluation experiments,and dynamic temporary plugging performance experiments in cores were conducted at 34°C.Results show that as the molecular weight of the cross-linking agent(at 0.01 g)in the DPPG molecule decreased from 1,000 to 200 Da,the fewer cross-linking sites of DPPG,the looser the microscopic three-dimensional mesh structure formed.The swelling ratio increased from 7 to 33 times.However,the complete degradation time increased from 40 to 210 min.Moreover,the DSC results confirmed that the higher the molecular weight of the cross-linking agent,the worse is chemical stability and the more prone it to self-degradation.DPPG samples had good temporary plugging performance in reservoir cores.DPPGs prepared by the cross-linking agent with smaller molecular weight has a stronger swelling ratio,higher gel strength,and greater plugging strength in the core permeabilities.Moreover,the degraded DPPG is less damaging to the cores.However,their slower degradation rates take a slightly longer times to reach complete degradation.The results of this paper can provide new ideas and a theoretical basis for the development of particle gel-type temporary plugging agents(TPA)with controllable degradation time in low-temperature reservoirs.It can help to expand the application range of existing DPPG reservoir conditions.

SiC FIBER／ALUMINIUM PREFORM WIRES FABRICATEDBY ULTRASONIC LIQUID INFILTRATION PROCESS

ＳｉＣＦＩＢＥＲ／ＡＬＵＭＩＮＩＵＭＰＲＥＦＯＲＭＷＩＲＥＳＦＡＢＲＩＣＡＴＥＤＢＹＵＬＴＲＡＳＯＮＩＣＬＩＱＵＩＤＩＮＦＩＬＴＲＡＴＩＯＮＰＲＯＣＥＳＳＺｈａｎｇＣｈｅｎｇｅ；ＷａｎｇＬｉｎｇｓｅｎ（ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙｏｆ...

Model of Preformed Hole-Pairs in Cuprate Superconductors

A model of preformed hole-pairs in cuprate superconductors has been proposed based on some experimental results i.e., 1) electron paramagnetic resonance spectra of quenched superconductors which show very frequently the fragment (CuO)4 broken off from the CuO2 layer in the structure, 2) 41 meV peak observed in neutron diffraction and nuclear magnetic resonance spectra of superconductors, 3) Heisenberg exchange interaction leading to ferromagnetism observed in CuO which is an essential ingredient of all superconductors and some generally accepted conclusions i.e., a) that the order parameter in superconductors has dx2–y2 symmetr and b) coherence length is of the order of 15 - 20 Angstrom. Heisenberg exchange interaction between two (CuO4) plaquettes each containing a lattice hole binds the two holes which are the charge carriers in the cuprate superconductors. It is not very clear whether the hole-pair is in the triplet or singlet state, but the triplet state is supported by the experimental observation of ferromagnetism in the parent material CuO. The proposed hole-pair singlet is different from Zhang-Rice singlet.