ANALYSIS FOR AIRCRAFT TAXIING AT VARIABLE VELOCITY ON UNEVENNESS RUNWAY BY THE POWER SPECTRAL DENSITY METHOD

In this paper a novel approach for the analysis of non stationary response of aircraft landing gear taxiing over an unevenness runway at variable velocity is explored, which is based on the power spectral density method. A concerned analytical landing gear model for simulating actual aircraft taxiing is formulated. The equivalent linearization results obtained by probabilistic method are inducted to treat landing gear non linear parameters such as shock absorber air spring force, hydraulic damping and Coulomb friction, tire stiffness and damping. The power spectral density for non stationary analysis is obtained via variable substitution and then Fourier transform. A representative response quantity, the overload of the aircraft gravity center, is analyzed. The frequency response function of the gravity overload is derived. The case study demonstrates that under the same reached velocity the root mean square of the gravity acceleration response from constant acceleration taxiing is smaller than that from constant velocity taxiing and the root mean square of the gravity acceleration response from lower acceleration taxiing is greater than that from higher acceleration.

ESTIMATION OF THE NUMBER OF CORRELATED SOURCES WITH COMMON FREQUENCIES BASED ON POWER SPECTRAL DENSITY

Blind source separation and estimation of the number of sources usually demand that the number of sensors should be greater than or equal to that of the sources, which, however, is very difficult to satisfy for the complex systems. A new estimating method based on power spectral density （PSD） is presented. When the relation between the number of sensors and that of sources is unknown, the PSD matrix is first obtained by the ratio of PSD of the observation signals, and then the bound of the number of correlated sources with common frequencies can be estimated by comparing every column vector of PSD matrix. The effectiveness of the proposed method is verified by theoretical analysis and experiments, and the influence of noise on the estimation of number of source is simulated.

Four Years of Daily Photon Emissions That Have Predicted Major Earthquakes: Raw Data, Spectral Power Density Analyses and Implications for the Geosciences

The daily median ground surface flux densities per day from a continuously operating photomultiplier tube unit for four years in Sudbury, Ontario are presented for December 2010 to December 2014. Increases of about 2 to 4 PMT units (1 unit = 5 × 10-11 W·m-2) for median daily measures reliably occurred about two weeks before M ≥ 7.7 earthquakes anywhere on the planet. The PMT units, until June 2014, usually returned to baseline within a few days after the events. There has been a slow positive drift in flux power density since about 2012 and a conspicuous maintained increase after May, 2014. The equivalent energy per day if it were represented isotropically within the volume occupied by the earth is the same order of magnitude as the average daily global total seismic energy release. Spectral power densities revealed enhanced peaks (periodicities) between 100 to 150 days, 60 days, 30 days, and 25 days. Discriminable peaks in power were noted around 18 days, 14 days, and 4 to 6 days. These results suggest that continuous measurement of photonemissions within hyper-dark conditions may reveal geophysical processes that precede larger seismic events and could reflect the movement of the earth-solar system around the galactic center.

Power spectral density analysis for nonlinear systems based on Volterra series

A consequence of nonlinearities is a multi-harmonic response via a monoharmonic excitation.A similar phenomenon also exists in random vibration.The power spectral density(PSD)analysis of random vibration for nonlinear systems is studied in this paper.The analytical formulation of output PSD subject to the zero-mean Gaussian random load is deduced by using the Volterra series expansion and the conception of generalized frequency response function(GFRF).For a class of nonlinear systems,the growing exponential method is used to determine the first 3 rd-order GFRFs.The proposed approach is used to achieve the nonlinear system’s output PSD under a narrow-band stationary random input.The relationship between the peak of PSD and the parameters of the nonlinear system is discussed.By using the proposed method,the nonlinear characteristics of multi-band output via single-band input can be well predicted.The results reveal that changing nonlinear system parameters gives a one-of-a-kind change of the system’s output PSD.This paper provides a method for the research of random vibration prediction and control in real-world nonlinear systems.

Roughness evaluation of three-dimensional asphalt pavement based on two-dimensional power spectral density

To solve the problem of the lack of comprehensive evaluation of three-dimensional(3D)asphalt pavement roughness,a method for evaluating the asphalt pavement roughness is proposed based on two-dimensional(2D)power spectral density(PSD).By calculating the 2D PSD of a 3D asphalt pavement and converting it into the longitudinal average asphalt pavement PSD,the relationship between the evaluation method of the 3D asphalt pavement roughness and the current evaluation standard of roughness is established.Combined with the road-fitting formula used in international standards,the elevation data of the A,B,C,and D grades of the 3D asphalt pavement are simulated by the harmonic superposition method.According to the proposed method,the longitudinal PSD of each level of simulated asphalt pavement is calculated and compared with the standard spectral line of each pavement level.This approach verifies the effectiveness of the proposed method in evaluating the roughness of the 3D asphalt pavement.Compared with the PSD of a certain horizontal profile elevation,it is verified that the fluctuation amplitude of the spectral line calculated by the proposed method is greatly improved.The results show that the proposed method can evaluate the roughness of asphalt pavements more comprehensively and accurately and has strong practicability.

EVALUATION OF POWER SPECTRAL DENSITY OF PASSIVE INTERMODULATION DISTORTION IN HIGH-POWER COMMUNICATION SATELLITE SYSTEMS

In order to analyze the deleterious effects of Passive InterModulation (PIM) on high power communication satellite systems, the basic concept of PIM is introduced, and an equation for the power spectral density of the n-th order PIM distortion insuch systems is derived by applying flat signal-power spectrum assumption and Fourier transform method. It is indicated that PIM level generally decreases with order and the lowest frequency receive channel in the receive band is the channel of most affected by PIM interference.

The Wavefront Power Spectral Density Measurement of Aspheric Lens with Long Focal-Length Using a Computer-Generated Hologram

To ensure the performance of the optical system, the machining accuracy of lens with long focal lengths is required to ensure the image quality. A new method for lens transmission wavefront power spectral density (PSD) in mid-frequency domain measurement using binary phase computer-generated hologram (CGH) is presented. This technique is widely applicable and is particularly useful for measuring large-size lenses with long focal lengths. A comparison experiment of the CGH measurement with results from a Fizeau sphere interferometry method is carried out to verify the accuracy and convenience of the measurement. Furthermore, measurement uncertainty due to CGH fabrication process is analysed. Analysis of the CGH test showed the overall accuracy of less than 1 nm RMS for a sphere lens with over 30 m focal length and Φ410 mm clear aperture. CGH can provide reference spheres with high precision, in the meantime greatly shorten air space, thus reducing the effect of vibration and air turbulence, therefore is of great importance for lens transmission wavefront PSD measurement. The realization of high precision, high efficiency and nondestructive testing of long focal-lens wavefront PSD ensure the ultra-precision and certainty level of machining, hence improving the comprehensive performance of the optical system.

The Changes of Heart Rate Power Spectral Density during Head-up Tilt Test

To study the role of autonomic nervous system in the period of developing syncope induced by head-up tilt test(HUT), we analysed the changes of heart rate power spectral density(HRPSD) in 50 patients with unexplained syncope, including 15 positive patients (Group 1) and 35 negative patients(Group 2), and 15 negative healthy persons(Group 3) in 5 minute periods before and after tilting and 5 minutes before the end of test. HRPSD and their changes in total(T), very low-frequence(VLF), low-frequence(LF), high-frequence(HF) and the ratio of low/high frequence(LF/HF) were similar (P>0.05) 5 minutes before and after tilting among three groups. Five minutes before the end of test, Group 1 had obvious increase of T, VLF, LF and LF/HF while Group 2 and 3 had not such significant changes. There was significant difference(P<0.01) compared Group 1 with Group 2, 3. The results showed that the abnormal regulatory function of autonomic nervous system played an important role in the mechanism of symcope induced by HUT, the positive group had abnormal increase of sympathetic tone and imbalance of sympathetic/parasympathetic neural tone before syncope appeared.

Nonlinear distortion analysis for multisine excitation constrained by power spectral density

Nonlinear distortion introduced by an amplifier when subjected to a multisine excitation decreases the measurement accuracy in many metrological and measurement areas. In this paper, we performed qualitative and quantitative analyses of the nonlinear distortion with the multisine excitations constrained by a constant power spectral density. We present the numerical results with respect to different tone spacings,nonlinear orders, harmonic phases and tone distributions. Moreover, three as-pects of contributions are made to further reveal the distortion mechanism. First, we find that the type Ⅱ components for Schr- oeder-phase multisines distribute uniformly but not all in anti-phase to the type I components for the second order nonlinearity. Second,we simulate the variance of the type I and Ⅱ components and their summation to explain the principle of reducing the type Ⅱ distortion by averaging the results obtained using multiple realizations of random-phase multisines. Third, we observe a special distortion distribution mechanism for the Schroeder-phase multisine excitation The results contribute to a better estima-tion and understanding of the nonlinear distortion.

Degradation of effective carrier-power-to-noise densityratio based on code trackingspectral sensitivitycoefficient for GNSS radio frequencycompatibilityin C band

The frequency band between 5 010 MHz and 5 030 MHz allocated as C band has been used as a candidate in the global navigation satellite systems （GNSS） along with more and more naviga- tion services in L band. The potential benefits and technical requirements of C band for satellite navi- gation have been analyzed before. However the degradation of effective carrier-power-to-noise densi- ty ratio（ A （C/No ）eu） based on code tracking spectral sensitivity coefficient（ CT_SSC ） as a compati- bility assessment methodology for potential GNSS radio frequency compatibility in C-Band has not been discussed clearly. So the compatibility of the signals in the C band between BeiDou （BD） B1 C and GPS L1C, L1C/A, Galileo E1Os as the interoperability or classical signals in L band is analyzed. Simulation results reveal the interference degree between BD III B1C and GPS L1C/A, L1C, Galileo E1OS. The results can also reveal that the multiplexed binary offset carrier （MBOC） and binary phase shift keying （BPSK） modulation is not appropriate for C band.

基于PSD特征的FBCCA脑电信号识别方法

当前基于稳态视觉诱发电位(steady-state visual evoked potential,SSVEP)的脑机接口(brain-computer interfaces,BCIs)使用的都是单一识别算法,针对不同时间长度的识别准确率较低。提出了一种基于滤波器组的典型相关分析(filter bank canonical correlation analysis,FBCCA)与功率谱密度(power spectral density,PSD)分析相结合的SSVEP识别算法,可以提高SSVEP识别的普适性与准确率。该方法使用FBCCA寻找高相似度的参考频率信号,再通过多组PSD分析来锁定最终的响应频率,完成频率识别。该方法无需经过训练就能得到较高的识别准确率。实验结果表明:在刺激时长为1 s时,该方法能达到86.61%的准确率,比PSD分析方法提升了5.44%,比典型相关性分析方法(canonical correlation analysis,CCA)提升了10.38%的准确率,比FBCCA提升了8.86%的准确率。

Porosity Evaluation and the Power Spectral Densities Analyses of Carbon-Nickel Composite Films Annealed at Different Temperatures

The densification and the fractal dimensions of carbon-nickel films annealed at different temperatures 300, 500, 800, and 1000℃ with emphasis on porosity evaluation are investigated. For this purpose, the refractive index of films is determined from transmittance spectra. Three different regimes are identified, T 〈 500℃, 500℃ 〈 T 〈 800℃ and T 〉 800℃. The Rutherford baekscattering spectra show that with increasing the annealing temperature, the concentration of nickel atoms into films decreases. It is shown that the effect of annealing temperatures for increasing films densification at T 〈 500℃ and T 〉 800℃ is greater than the effect of nickel concentrations. It is observed that the effect of decreasing nickel atoms into films at 500℃ 〈 T 〈 800℃ strongly causes improving porosity and decreasing densification. The fractal dimensions of carbon-nickel films annealed from 300 to 500℃ are increased, while from 500 to 1000℃ these characteristics are decreased. It can be seen that at 800℃, films have maximum values of porosity and roughness.

Power Spectral Analysis of Orthogonal Pulse-Based TH-UWB Signals

The paper analyzes power spectral density (PSD) of orthogonal pulse-based signals for time hopping ultra wideband (TH-UWB) systems. Our extensive studies show that the PSD of these signals not only depends on the time dithering code and the modulation schemes, but also on the energy spectral density (ESD) of orthogonal pulses. The different order orthogonal pulses provide different ESD which changes the shape of continuous spectral component with symbols. We show that orthogonal pulse-based signals reduce the dynamic range of amplitude of discrete spectral components. Further, we reduce the dynamic range by adopting longer TH code over orthogonal pulse-based signals. As a result, UWB system performance improves with average transmitted power. The theoretical analysis of PSD of orthogonal pulse-based TH-UWB signal is provided in details and verified through simulation results.

基于PSD的牵引车APU支架随机振动疲劳分析

为解决某牵引车空气处理单元(APU)支架在道路试验中发生开裂的问题,首先建立了APU支架台架试验有限元模型,然后基于模态频率响应分析和振动试验功率谱密度,对APU支架进行随机振动疲劳分析,并且与台架试验对标。基于对标成功的模型,对支架进行改进并再次分析,结果表明,优化后的支架在后续台架试验中再未出现裂纹,说明基于功率谱密度(PSD)的随机振动疲劳分析具有很好的可靠性和适用性。

Matlab内建psd函数在工程随机振动谱分析中的修正方法

介绍了工程随机振动功率谱的计算过程,并对工程计算中应用广泛的Matlab软件的内建谱分析函数psd进行了详细分析,指出了该函数在进行随机振动谱分析中存在的问题,给出了修正方法,通过算例计算验证了该修正方法的正确性.

新疆和田台阵PSD与PDF分析

和田台阵是我国第一个自主建成并运行至今的小孔径台阵,承担着监测印巴地区核试验以及我国西部地震活动的重要使命.台阵波形数据中充斥着背景噪声,直接影响着数据质量.为了评估台阵噪声水平,本文利用Welch平均周期法对9个子台记录的数十万条噪声样本进行功率谱估计,对出现的谱异常进行了总结归纳,通过绘制概率密度函数图以及单频曲线来研究背景噪声变化范围和规律,最后针对台阵降噪提出了建设性意见.研究结果表明,中心台长周期噪声功率谱密度随季节变化显著,具有周期性;受温度和气压影响,水平分量长周期噪声变化幅度较大,局部频段超出新高噪声模型,建议改善仪器安装条件,或者利用数学方法进行校正.所有子台短周期噪声变化规律与长周期相反,受到采石场影响,谱密度曲线在4~8Hz之间出现形态规则的高频尖刺,A1、B3、B4子台最为明显,可以通过窄带滤波或者聚束予以压制.本文取得的研究成果为台阵运维提供重要依据,除此之外,总结出的不同地震频谱特征也为地震解释工作提供重要参考.

PSD在超精密加工实验数据分析的应用

功率谱密度(power spectral density,PSD)用于描述随机过程的功率随频率的分布。在超精密加工实验中,功率谱方法不仅仅用于切削力信号分析,还可以用于超精密加工表面微观形貌分析;既可以反映出不同频率在表面形貌中所占的比重,还可揭示切削参数、工件材料性能等对超精密加工表面生成的影响程度。该文使用PSD方法对超精密飞刀铣削在不同进给速度下加工不同工件材料的实验结果进行分析,结果表明,相比于表面粗糙度参数来说,PSD方法更有利于表现出工件材料对超精密加工表面的影响。

基于ICA与PSD的ERD/ERS信号检测

介绍一种基于独立分量分析(ICA)空间滤波结合功率谱密度(PSD)曲线分析法用于提取大脑在想象动作时产生事件相关去同步/同步(ERD/ERS)信号的方法.其检测流程为:先对想象动作诱发的脑电(EEG)信号进行ICA分解得到独立分量与相应的解混矩阵,再按特征频段取其主要分量得到滤波后数据,然后采用短时傅里叶变换计算相关导联EEG信号在特征时段与频段的PSD曲线,引入ERD/ERS系数作为量化指标以进行想象动作的识别.计算结果表明,上述方法能够显著增强运动想象脑电信号的ERD/ERS特征信息,且通过实际分类验证,采用该方法可以获得更高的识别正确率,较传统信息检测方法平均提高8%以上.

气液两相段塞流的PSD和PDF特征分析

在气液两相段塞流理论基础上,通过大量实验,利用LabVIEW平台进行数据采集和处理,并引进数字信号理论和统计学分析方法,得出了段塞流在不同时期、不同形态的概率密度函数(PDF)特征和功率谱密度函数(PSD)特征.段塞流的压力概率密度函数呈现单峰、双峰、多峰分布,尤以双峰分布最为普遍;段塞流的压差概率密度函数分布符合正态分布,呈现单峰分布;段塞流的功率谱在整个频率范围内随着频率增大而缓慢下降,频率范围内出现两个幅度比较明显的特征峰.利用PSD和PDF特征分析可以进行气液两相流的流型识别,为研究流型和管道系统设计提供帮助.

基于PSD法输入的输电塔结构随机振动分析

基于脉动风的基本理论和Davenport风压功率谱,提出在频域内对输电塔结构迎风面施加风压功率谱的方法,并进行输电塔结构的随机振动分析,得到输电塔自振频率及风压谱施加后的各向位移变化情况,将风压功率谱计算结果与静力计算结果进行比较,得到风振系数加载后结构位移数值偏小,造成设计偏于不安全的结论。建议设计中可尝试动力加载方法,使结构设计更加合理。