Observer-based dynamic event-triggered control for distributed parameter systems over mobile sensor-plus-actuator networks

We develop a policy of observer-based dynamic event-triggered state feedback control for distributed parameter systems over a mobile sensor-plus-actuator network.It is assumed that the mobile sensing devices that provide spatially averaged state measurements can be used to improve state estimation in the network.For the purpose of decreasing the update frequency of controller and unnecessary sampled data transmission, an efficient dynamic event-triggered control policy is constructed.In an event-triggered system, when an error signal exceeds a specified time-varying threshold, it indicates the occurrence of a typical event.The global asymptotic stability of the event-triggered closed-loop system and the boundedness of the minimum inter-event time can be guaranteed.Based on the linear quadratic optimal regulator, the actuator selects the optimal displacement only when an event occurs.A simulation example is finally used to verify that the effectiveness of such a control strategy can enhance the system performance.

Actuator and sensor fault isolation in a class of nonlinear dynamical systems

Fault isolation in dynamical systems is a challenging task due to modeling uncertainty and measurement noise,interactive effects of multiple faults and fault propagation.This paper proposes a unified approach for isolation of multiple actuator or sensor faults in a class of nonlinear uncertain dynamical systems.Actuator and sensor fault isolation are accomplished in two independent modules,that monitor the system and are able to isolate the potential faulty actuator(s)or sensor(s).For the sensor fault isolation(SFI)case,a module is designed which monitors the system and utilizes an adaptive isolation threshold on the output residuals computed via a nonlinear estimation scheme that allows the isolation of single/multiple faulty sensor(s).For the actuator fault isolation(AFI)case,a second module is designed,which utilizes a learning-based scheme for adaptive approximation of faulty actuator(s)and,based on a reasoning decision logic and suitably designed AFI thresholds,the faulty actuator(s)set can be determined.The effectiveness of the proposed fault isolation approach developed in this paper is demonstrated through a simulation example.

Optical micro/nanofiber enabled tactile sensors and soft actuators:A review

As a combination of fiber optics and nanotechnology,optical micro/nanofiber(MNF)is considered as an important multifunctional building block for fabricating various miniaturized photonic devices.With the rapid progress in flexible optoelectronics,MNF has been emerging as a promising candidate for assembling tactile sensors and soft actuators owing to its unique optical and mechanical properties.This review discusses the advances in MNF enabled tactile sensors and soft actuators,specifically,focusing on the latest research results over the past 5 years and the applications in health monitoring,human-machine interfaces,and robotics.Future prospects and challenges in developing flexible MNF devices are also presented.

Distributed fault diagnosis observer for multi-agent system against actuator and sensor faults

Component failures can cause multi-agent system(MAS)performance degradation and even disasters,which provokes the demand of the fault diagnosis method.A distributed sliding mode observer-based fault diagnosis method for MAS is developed in presence of actuator and sensor faults.Firstly,the actuator and sensor faults are extended to the system state,and the system is transformed into a descriptor system form.Then,a sliding mode-based distributed unknown input observer is proposed to estimate the extended state.Furthermore,adaptive laws are introduced to adjust the observer parameters.Finally,the effectiveness of the proposed method is demonstrated with numerical simulations.

FINITE ELEMENT MODELING OF MODERATELY THICK COMPOSITE PLATE WITH PIEZOELECTRIC SENSORS AND ACTUATORS

A rectangular finite element for laminated plate with bonded and/or embedded piezoelectric sensors and actuators is developed based on the variational principle and the first order shear deformation theory. The element has four-node, 20-degrees-of-freedom with one potential degree of freedom for each piezoelectric layer to represent the piezoelectric behavior. The higher order derivation of deflection is obtained by using the normal rotation expressions to take the effects of transverse shear deformation into considerations. The finite element can accurately simulate the deformation of both thin and moderately thick plates. A Fortran program is written and a number of benchmark tests are exercised to verify its effectiveness. Results are compared well with the existing data. The unbalanced composite with piezoelectric layers is then analyzed by using the model. Results show that the changes of the ratio between the thickness of positive angle layers and the negative angle layers have an effect on the deformation of the structure under the same electric loading.

Intelligent emergency service system based on wireless sensor and actuator networks

An intelligent emergency service（ IES） system is designed for indoor environments based on a wireless sensor and actuator network（ WSAN） composed of a gateway, sensor nodes, and a multi-robot system（ MRS）. If the MRS receives accident alarm information, the group of robots will navigate to the accident sites and provide corresponding emergency services.According to the characteristics of the MRS, a distributed consensus formation protocol is designed, which can assure that the multiple robots arrive at the accident site in a specified formation. The prototype emergency service system was designed and implemented, and some relevant simulations and experiments were carried out. The results showthat the MRS can successfully provide emergency lighting and failure node replacement services when accidents happen. The effectiveness of the algorithm and the feasibility of the system are verified.

一种基于高压静电纺丝工艺制备的P(VDF-TrFE)/PZT压电传感器及其在睡眠监测中的应用

针对日常睡眠监测的需求,提出一种基于高压静电纺丝工艺制备的P(VDF-TrFE)/锆钛酸铅(PZT)压电传感器并对其性能进行了研究。首先,介绍了P(VDF-TrFE)/PZT压电传感器的制作及封装流程。其次对其灵敏度,频率响应特性,瞬时响应和稳定性等进行了测试。结果表明,该传感器不仅具有良好的微观外貌形态,且相比于纯P(VDF-TrFE)压电传感器0.73 V/N的灵敏度,制备的含30%PZT的P(VDF-TrFE)/PZT压电传感器灵敏度是纯P(VDF-TrFE)压电传感器的2.5倍,达到了1.78 V/N。此外在低频下能够保持稳定压电输出且具备2 ms较快的响应时间。最后采用自制的P(VDF-TrFE)/PZT压电传感器测量人体心冲击信号,并通过支持向量机(SVM)训练睡眠分期模型实现了对睡眠质量的监测,四分类模型平均准确率达到72.5%,为可穿戴睡眠监测传感器的选择提供了参考。

Research on Composite PZT for Largedisplacement Actuators

A new kind of composite piezoelectric ceramics for large-displacement actuators, which were composed of reduced and unreduced layers, was prepared from normal PZT by chemical reduction. The stress distribution inside the composite PZT was researched and the chemical reduction conditions were explored. The actuating properties of reduced PZT were also studied. It is found that the optimal ratio of reduced layer thickness for the composite structure is 0.3; Reduced composite PZT has lower resonance frequency and 3 times larger displacement than that of the traditional PZT; Re-oxide phases are found in reduced layer of composite PZT showing the reduction procedure needs to be improved.

A Review of Smart Materials for the Boost of Soft Actuators,Soft Sensors,and Robotics Applications

With the advance of smart material science,robotics is evolving from rigid robots to soft robots.Compared to rigid robots,soft robots can safely interact with the environment,easily navigate in unstructured fields,and be minimized to operate in narrow spaces,owning to the new actuation and sensing technologies developed by the smart materials.In the review,different actuation and sensing technologies based on different smart materials are analyzed and summarized.According to the driving or feedback signals,actuators are categorized into electrically responsive actuators,thermally responsive actuators,magnetically responsive actuators,and photoresponsive actuators;sensors are categorized into resistive sensors,capacitive sensors,magnetic sensors,and optical waveguide sensors.After introducing the principle and several robotic prototypes of some typical materials in each category of the actuators and sensors.The advantages and disadvantages of the actuators and sensors are compared based on the categories,and their potential applications in robotics are also presented.

Improved control of distributed parameter systems using wireless sensor and actuator networks:An observer-based method

In this paper,the control problem of distributed parameter systems is investigated by using wireless sensor and actuator networks with the observer-based method.Firstly,a centralized observer which makes use of the measurement information provided by the fixed sensors is designed to estimate the distributed parameter systems.The mobile agents,each of which is affixed with a controller and an actuator,can provide the observer-based control for the target systems.By using Lyapunov stability arguments,the stability for the estimation error system and distributed parameter control system is proved,meanwhile a guidance scheme for each mobile actuator is provided to improve the control performance.A numerical example is finally used to demonstrate the effectiveness and the advantages of the proposed approaches.

Iterative Learning Control for Distributed Parameter Systems Based on Non-Collocated Sensors and Actuators

In this paper, an open-loop PD-type iterative learning control(ILC) scheme is first proposed for two kinds of distributed parameter systems(DPSs) which are described by parabolic partial differential equations using non-collocated sensors and actuators. Then, a closed-loop PD-type ILC algorithm is extended to a class of distributed parameter systems with a non-collocated single sensor and m actuators when the initial states of the system exist some errors. Under some given assumptions, the convergence conditions of output errors for the systems can be obtained. Finally, one numerical example for a distributed parameter system with a single sensor and two actuators is presented to illustrate the effectiveness of the proposed ILC schemes.

Finite Element Analysis of Smart Structures with Piezoelectric Sensors/Actuators Including Debonding

In vibration active control of composite structures, piezoelectricsensors/actuators are usually bonded to the surface of a host structure. Debonding of piezoelectricsensors/actuators can result in significant changes to the static and dynamic response. In thepresent paper, an novel Enhanced Assumed Strain(EAS) piezoelectric solid element formulation isdeveloped for vibration active control of laminated structures bonded with piezoelectric sensors andactuators. Unlike the conventional brick elements, the present formulation is very reliable, moreaccurate, and computationally efficient and can be used to model the response of shell structuresbesides thin plates. Delaminations are modeled by pairs of nodes with the same coordinates butdifferent node numbers, and numerical results demonstrate the performance of the element and theglobal and local effects of debonding sensors/actuators on the dynamics of the adaptive laminates.

Optimization of actuator/sensor position of multi-body system with quick startup and brake

A new method was put forward to optimize the position of actuator/sensor of multi-body system with quick startup and brake. Dynamical equation was established for the system with intelligent structure of piezoelectric actuators. According to the property of the modes varying with time, the performance index function was developed based on the optimal configuration principle of energy maximal dissipation, and the relevant optimal model was obtained. According to its characteristic, a float-encoding genetic algorithm, which is efficient, simple and excellent for solving the global-optimal solution of this problem, was adopted. Taking the plane manipulator as an example, the result of numerical calculation shows that, after the actuator/sensor position being optimized, the vibration amplitude of the multi-body system is reduced by 35% compared with that without optimization.

ACTIVE VIBRATION CONTROL OF A CANTILEVER BEAM USING PIEZOELECTRIC SENSORS AND ACTUATORS

The topic of vibration control with distributed actuators has been the subject of many researches. This paper is concerned with the vibration control of a cantilever beam equipped with piezoelectric ceramics as sensors and actuators. One piezoelectric ceramic is bonded to the structure and provides control input for the structure, while the other piezoelectric ceramic provides the feedback signal. An approach to identification and control is presented. Observation spillover is eliminated by prefiltering the sensor data. A procedure used to determine actuator and sensor location, is discussed based on the modes to be controlled. Finally, the experimental results are presented to verify the proposed method.

Piezoelectric Actuator/Sensor Wave Propagation Based Nondestructive Active Monitoring Method of Concrete Structures

In order to monitor the basic mechanical properties and interior damage of concrete structures,the piezoelectric actuator/sensor based wave propagation method was investigated experimentally in the laboratory using a specifically designed test setup.The energy attenuation of stress waves was measured by the relative index between the output voltage of sensors and the excitation voltage at the actuator.Based on the experimental results of concrete cube and cylinder specimens,the effect of excitation frequencies,excitation amplitude,wave propagation paths and the curing age on the output signals of sensors are evaluated.The results show that the relative voltage attenuation coefficient RVAC is an effective indicator for measuring the attenuation of stress waves through the interior of concrete.

APPLICATION OF FEA TO THE COLLOCATION OF ACTUATOR/SENSOR IN THE INTELLIGENT STRUCTURES

The piezothermoelectric actuator/sensor collocation for advanced intelligent structure is studied. The quasi-static equations of piezothermoelasticity are used to analyze the coupling effects between the displacement, temperature and electric fields of piezothermoelasticity continua and the governing equations for piezothermoelasticity continua are derived to discuss the effects of coupling factors on the control/sensing performance in intelligent structure. Based on those analyses, a finite element analysis model of distributed piezothertnoelectric continua is developed later. The thermal stress and deformation of a beam are calculated by FEA method so as to determine the optimal actuator/sensor placement. Based on the results of the optimal analysis procedure of actuator/sensor placement, some conclusions of actuator/sensor placement are obtained. Thus, the optimal actuator/sensor placement for piezothermoelectric intelligent structure can be found from the actuator/sensor placements available so that intelligent system will have the best controllability and observability.

SVD Approach for Actuator and Sensor Placement in Active Vibration Control of Large Cable Net Structures

The actuator and sensor placement problem for active vibration control of large cable net structures is investigated in this paper.Since the structures exhibit closely spaced modes in the range of low frequencies,the number of modes to be considered is quite large after modal truncation,while only a limited number of actuators and sensors are to be placed.This makes it hard to determine the actuator and sensor locations with the existing placement methods in the literature such as the methods based on the controllability/observability grammian.To deal with this issue,an actuator and sensor placement method based on singular value decompositions(SVD)of the input and output matrices is proposed,which guarantees the modal controllability and observability of the system.The effectiveness of the SVD based method is verified through numerical simulations in which comparisons are conducted between randomly-chosen locations and the optimal ones obtained by a genetic algorithm.

Zigbee Based Wireless Sensor and Actuator Network for Service Robot Intelligent Space

Wireless sensor and actuator network is the key technology of service robot intelligent space. This paper is concerned with design and implementation of a ZigBee based wireless sensor and actuator network (hereinafter referred to as ZWSAN), which has been applied in our service robot intelligent space successfully. Firstly, a simplified ZigBee stack applied to ZWSAN is proposed and the primitives of the stack are illustrated after a short overview of ZigBee protocols. Then the implementation of hardware module and software stack is introduced in detail as well as several representative devices integrated into ZWSAN, including environmental sensors for environmental perception, home devices controllers for device control, embedded speech recognition module for speech control, IMU module for abnormal behaviors detection and laser robot control for service robot navigation. An application example is described to demonstrate how the devices in ZWSAN to provide service cooperatively. Finally, we conclude this paper and discuss the future directions.

Bioinspired Multifunctional Self-Sensing Actuated Gradient Hydrogel for Soft-Hard Robot Remote Interaction

The development of bioinspired gradient hydrogels with self-sensing actuated capabilities for remote interaction with soft-hard robots remains a challenging endeavor. Here, we propose a novel multifunctional self-sensing actuated gradient hydrogel that combines ultrafast actuation and high sensitivity for remote interaction with robotic hand. The gradient network structure, achieved through a wettability difference method involving the rapid precipitation of MoO_(2) nanosheets, introduces hydrophilic disparities between two sides within hydrogel. This distinctive approach bestows the hydrogel with ultrafast thermo-responsive actuation(21° s^(-1)) and enhanced photothermal efficiency(increase by 3.7 ℃ s^(-1) under 808 nm near-infrared). Moreover, the local cross-linking of sodium alginate with Ca^(2+) endows the hydrogel with programmable deformability and information display capabilities. Additionally, the hydrogel exhibits high sensitivity(gauge factor 3.94 within a wide strain range of 600%), fast response times(140 ms) and good cycling stability. Leveraging these exceptional properties, we incorporate the hydrogel into various soft actuators, including soft gripper, artificial iris, and bioinspired jellyfish, as well as wearable electronics capable of precise human motion and physiological signal detection. Furthermore, through the synergistic combination of remarkable actuation and sensitivity, we realize a self-sensing touch bioinspired tongue. Notably, by employing quantitative analysis of actuation-sensing, we realize remote interaction between soft-hard robot via the Internet of Things. The multifunctional self-sensing actuated gradient hydrogel presented in this study provides a new insight for advanced somatosensory materials, self-feedback intelligent soft robots and human–machine interactions.

Improved control for distributed parameter systems with time-dependent spatial domains utilizing mobile sensor-actuator networks

A guidance policy for controller performance enhancement utilizing mobile sensor-actuator networks （MSANs） is proposed for a class of distributed parameter systems （DPSs）, which are governed by diffusion partial differential equations （PDEs） with time-dependent spatial domains. Several sufficient conditions for controller performance enhancement are presented. First, the infinite dimensional operator theory is used to derive an abstract evolution equation of the systems under some rational assumptions on the operators, and a static output feedback controller is designed to control the spatial process. Then, based on Lyapunov stability arguments, guidance policies for collocated and non-collocated MSANs are provided to enhance the performance of the proposed controller, which show that the time-dependent characteristic of the spatial domains can significantly affect the design of the mobile scheme. Finally, a simulation example illustrates the effectiveness of the proposed policy.