Impacts of automated passenger cars on the capacity of a freeway basic section: applicability in the determination of vehicle adjustment factors in mixed traffic

The highway capacity manual(HCM)provides a formula to calculate the heavy vehicle adjustment factor(fHV)as a function of passenger car equivalent factors for the heavy vehicle(ET).However,a significant drawback is that the methodology was established solely based on human-driven passenger cars(HDPC)and human-driven heavy vehicles(HDHV).Due to automated passenger cars(APCs),a new adjustment factor(fAV)might be expected.This study simulated traffic flows at different percentages of HDHVs and APCs to investigate the impacts of HDHVs and APCs on freeway capacity by analyzing their influence on fHV and fAV values.The simulation determined observed adjustment factors at different percentages of HDHVs and APCs(fobserved).The HCM formula was used to calculate(fHCM).Modifications to the HCM formula are proposed,and vehicle adjustment factors due to HDHVs and APCs were calculated(fproposed).Results showed that,in the presence of APCs,while fobserved and fHCM were statistically significantly different,fobserved and fproposed were statistically equal.Hence,this study recommends using the proposed formula when determining vehicle adjustment factors(fproposed)due to HDHVs and APCs in the traffic stream.

Estimation of Passenger Car Equivalents for Basic Freeway Sections at Different Traffic Conditions

Passenger car equivalent (PCE) is an important factor which is used to convert traffic volumes containing proportions of heavy good vehicles (HGVs) to a unify measure containing only passenger cars units (PCU). This paper uses large data base of real traffic raw data extracted from loop detector before being aggregated to estimate PCEs. These detectors are located on the M25 and the M42 motorway sites in the United Kingdom. The selected sites represent basic freeway segments as they are far away from the influence of entrance (on ramp) and exit (off ramp) sections. The data are filtered properly so as to estimate passenger car equivalents (PCEs) using lagging headway method for close following situations at different speed ranges. The results suggest that for the same location, the equivalency factors are varies significantly based traffic speed. However, it is proved that such variation with traffic speed is influenced by the differences in lengths between HGVs and cars. Regression models have also been developed linking the PCEs with traffic speed.

Explicit–Implicit Co-Simulation Techniques for Dynamic Responses of a Passenger Car on Arbitrary Road Surfaces

To study the durability of a passenger car, this work investigates numerical simulation techniques. The investigations are based on an explicit implicit approach in which substructure techniques are used to reduce the simulation time, allowing full vehicle dynamic analyses to be performed on a timescale that is dif cult or impossible with the conventional nite element model (FEM). The model used here includes all necessary nonlinearities in order to maintain accuracy. All key components of the car structure are modeled with deformable materials. Tire road interactions are modeled in the explicit package with contact-impact interfaces with arbitrary frictional and geometric properties. Key parameters of the responses of the car driven on six different kinds of test road surfaces are examined and compared with experimental values. It can be concluded that the explicit implicit co-simulation techniques used here are ef cient and accurate enough for engineering purposes. This paper also discusses the limitations of the proposed method and outlines possible improvements for future work.

NUMERICAL ANALYSIS OF NONLINEAR STABILITY FOR RAILWAY PASSENGER CARS

The Newton Raphson iteration and QR algorithm are combined to search the Hpf bifurcation point of the vehicle running on straight track and on large radius curved tracks. Limit cycles that are bifurcated from the equilibrium points and the saddle node bifurcation point are computed through employing a variable step Runge Kutta method and the Poincaré map. Finally, numerical simulations are carried out for the stability of a high speed passenger car operating on straight and large radius curved tracks. The influences of the radius of curvature and the superelevation of the track on the stability of the vehicle system are investigated.

STUDY ON DYNAMIC CURVING BEHAVIOR OF TILTING PASSENGER CARS

By using tilting carbodies, train can negotiate at a higher speed withoutreducing the passenger's ride quality. This is a good method to allow a significant increase inspeed at existing track to improve the railway transportation capability, and to enhance thecompetition ability of railways with other transportation systems. With the increase of the curvenegotiation speed, the wheel-rail lateral forces and wheel-rail wear of the tilting train willincrease. The self-steering radial bogie is an effective way to solve the problem. The dynamic modelof the tilting passenger car with self-steering bogies is established in detail, and the curvingperformance of the car is investigated.

Performance Development Target Setting of Passenger Car Diesel Engine

Setting engine emission targets to meet diesel car requirements is particularly important in engine performance development phase. Many researches are focused on associating vehicle performance with engine targets, but most work is done by testing, which is time and cost consuming, furthermore, the relationship of vehicle and engine will change when either engine or vehicle changes. A GT-Drive model to simulate New European Driving Cycle (NEDC) for passenger car is developed and calibrated by testing data, model precision is controlled within 5%. Time distribution of engine operating conditions when car running NEDC cycle has been analyzed, 10 critical major engine operating points are summarized according to running time proportion. Emission of NOx and smoke control regions containing these 10 points for target engine are set. Vehicle emissions are simulated and evaluated during engine development after engine performance test data are got, and engine combustion system layout and calibration are adjusted until vehicle targets are met. Vehicle is tested in chassis dynamometer finally, the testing results show a good agreement with the simulated results with an error of less than 5%, which proves that the emission value exchange of vehicle and engine is reliable. Performance target decomposition method for passenger car diesel presented can greatly shorten the development cycle and save costs.

Kinematic and Kinetic Analysis for the Tilting Mechanism of Railway Passenger Cars

The kinematics and kinetics of the tilting mechanism of railway passenger cars are studied. The parameters of the mechanism are given. The motions of the actuator, the center of gravity of the carbody and the center of coupler are calculated. Finally, the maximum driving force, output power and velocity of the actuator are discussed in detail.

Side Structure Sensitivity to Passenger Car Crashworthiness During Pole Side Impact

Side impact accidents of passenger cars with fixed poles may result in severe injuries to the vehicle occupants. In this paper, side structure intrusion was considered as the criterion for passenger cars crashworthiness during side impact with a pole. The relationship between side intrusions and the side structure stiffness was analyzed. The acceleration of the unstruck side vehicle body was selected as the criterion for studying the influence of different side structure components on the side structure stiffness during passenger car pole side impacts. The behavior was analyzed using finite element simulations. The results show that the rocker and the lower part of the B-pillar are the key parts of the side structures in determining the passenger car side stiffness. Passenger car pole side impact crashworthiness is, therefore, most sensitive to these two components.

Characterization of particulate matter from diesel passenger cars tested on chassis dynamometers

Emission characterization of particle number as well as particle mass from three diesel passenger cars equipped with diesel particulate filter（DPF）, diesel oxidation catalyst（DOC）and exhaust gas recirculation（EGR） under the vehicle driving cycles and regulatory cycle.Total particle number emissions（PNEs） decreased gradually during speed-up of vehicle from 17.3 to 97.3 km/hr. As the average vehicle speed increases, the size-segregated peak of particle number concentration shifts to smaller size ranges of particles. The correlation analysis with various particulate components such as particle number concentration（PNC）,ultrafine particle number concentration（UFPNC） and particulate matter（PM） mass was conducted to compare gaseous compounds（CO, CO2, HC and NOx）. The UFPNC and PM were not only emitted highly in Seoul during severe traffic jam conditions, but also have good correlation with hydrocarbons and NOxinfluencing high potential on secondary aerosol generation. The effect of the dilution temperature on total PNC under the New European Driving Cycle（NEDC）, was slightly higher than the dilution ratio. In addition, the nuclei mode（DP： ≤ 13 nm） was confirmed to be more sensitive to the dilution temperature rather than other particle size ranges. Comparison with particle composition between vehicle speed cycles and regulatory cycle showed that sulfate was slightly increased at regulatory cycle, while other components were relatively similar. During cold start test, semivolatile nucleation particles were increased due to effect of cold environment. Research on particle formation dependent on dilution conditions of diesel passenger cars under the NEDC is important to verify impact on vehicular traffic and secondary aerosol formation in Seoul.

Queue clearance rate method for estimating passenger car equivalents at signalized intersections

This study explored the use of queue clearance rate method for estimating passenger car equivalent （PCE） at signalized intersections. PCE was estimated based on the assumption that the rate at which a queue of vehicles clears the intersection is a function of its composition. Results of this method were compared with the results estimated by some popular techniques. A fourqegged intersection was simulated in VISSIM software and different techniques were used to convert the traffic mix into a uniform one. Parameters of VISSIM were modified to closely reflect the traffic behaviour under heterogeneous traffic conditions. All approaches of the intersection were loaded to saturated conditions and accuracy of estimated PCEs were established by comparing converted flow （PCE/h） with the capacity of an all-car traffic stream. Method based on saturation flow delivered the best result, but its use was limited to traffic composed only of two types of vehicles. Results of regression and optimization techniques were almost similar and the converted flow was close to the capacity of all-car stream. However, accuracy of these methods strongly relied on the correct measurement of saturation flow. Queue clearance rate method did not require value of saturation flow and yielded good estimates of PCE throughout the simu- lation runs. The maximum difference between the converted flow and capacity estimated with all car situations was found to be less than 10% in all cases considered in this study.

Tianjin Automotive Test Center & National Passenger Car Quality Supervision and Inspection Center——A State Testing and Universality Techniques Research Base in China

Tianiin Automotive Test Center has a test capability as well as a capability of conducting universality techniques research. With fixed assets of around RMB 76.44 million yuan and an architectural area of 11,200 sqm, test labs mainly include: auto emission test lab, full-scale vehicle crash test lab, auto safety test lab, auto lighting and view field test lab, engine test lab,

How to Share This“Cake”——Prediction on Chinese Passenger Car Market in 1996

In 1995, 325800 units cars were produced by Chinese car-makers, of which 312100 units were sold out. Concerning the market share, SVW Santanas enjoyed the top position, far beyond the other car models, and compared with the No. 2, Tianjin Charades, their market share was about 30% higher. Because of the

The market performance of foreign funded passenger car makers in China

1.Japan-based makers have presented most increasingly models and brands German-based car makers continued dominating the market until 2003 and the market shares of two