Commercially available niobium (V) oxide [Nb2O5], with barium acetate [Ba(CH3COO)2] and magnesium acetate [Mg(CH3COO)2-4H2O] was used as the starting material in the sol-gel process for preparing Ba(Mg1/3Nb2/3)O3 (BMN...Commercially available niobium (V) oxide [Nb2O5], with barium acetate [Ba(CH3COO)2] and magnesium acetate [Mg(CH3COO)2-4H2O] was used as the starting material in the sol-gel process for preparing Ba(Mg1/3Nb2/3)O3 (BMN) nanopowders. At first, Nb2O5 reacted with melting sodium hydroxide and transformed into dispersible oxide. The resulting glassy substance after cooling was dispersed and washed several times in distilled water to remove the Na+ ions. The as-prepared colloidal Nb2O5-nH2O was subsequently mixed with acetic solution of barium acetate and magnesium acetate according to the required molar proportions and followed by gelation. The ultrafine BMN powders were finally obtained after heat-treating the gel at 820℃for 1 h, and the as-sintered nanoceramics revealed a high relative density of 98.2%, and a high microwave Q-factor, of 10397 at 1.45GHz.展开更多
Ba(Mg1/3Nb2/3)O3(BMN)复合钙钛矿陶瓷具有高介电常数和高品质因子等介电性能,预示了其在光学领域的应用前景.本文采用第一性原理方法计算了BMN的电子结构,对其本征光学性能进行分析和预测.对固相合成六方相BMN的XRD测试结果进行Rietvel...Ba(Mg1/3Nb2/3)O3(BMN)复合钙钛矿陶瓷具有高介电常数和高品质因子等介电性能,预示了其在光学领域的应用前景.本文采用第一性原理方法计算了BMN的电子结构,对其本征光学性能进行分析和预测.对固相合成六方相BMN的XRD测试结果进行Rietveld精修(加权方差因子Rwp=6.73%,方差因子Rp=5.05%),在此基础上建立晶体结构模型并对其进行几何优化.运用基于密度泛函理论(DFT)的平面波赝势方法,对六方相BMN晶体模型的能带、态密度和光学性质进行理论计算.结果表明BMN的能带结构为间接带隙,禁带宽度Eg=2.728 e V.Mg-O和Ba-O以离子键结合为主,Nb-O以共价键结合为主,费米面附近的能带主要由O-2p和Nb-4d态电子占据,形成了d-p轨道杂化.修正带隙后,计算了BMN沿[100]和[001]方向上的复介电函数、吸收系数和反射率等光学性质.结果表明,BMN近乎光学各向同性,在可见光区,其本征透过率为77%<T<83%,折射率为1.91<n<2.14,并伴随一定的色散现象.实验测试结果与理论计算结果相吻合.展开更多
基于Swartz and Shrout的二次合成法,采用改进的两步法,将部分原料预合成,一次烧结合成具有100%钙钛矿结构的75Pb(Zn_(1/3)Nb_(2/3))O_3-10PbTiO_3-15BaTiO_3固溶体陶瓷。首先一次性称量PbO,然后和ZnNb_2O_6混合,在660～800℃预合成,将...基于Swartz and Shrout的二次合成法,采用改进的两步法,将部分原料预合成,一次烧结合成具有100%钙钛矿结构的75Pb(Zn_(1/3)Nb_(2/3))O_3-10PbTiO_3-15BaTiO_3固溶体陶瓷。首先一次性称量PbO,然后和ZnNb_2O_6混合,在660～800℃预合成,将预合成产物粉碎后再与TiO_2和BaCO_3按化学计量称量,充分混合后,在1060～1140℃保温1～2h烧结成陶瓷试样。实验结果表明:改进的两步法工艺能够将预合成温度降为660℃,烧结温度能被拓宽到80℃获得100%钙钛矿结构的固溶体陶瓷。不同于传统的预合成和烧结,改进的两步法工艺简单、有效,在预合成阶段没有形成钙钛矿相,烧结阶段陶瓷的成瓷和致密化同时进行,完成了中间相向钙钛矿相的转变,获得了介电性能优良的陶瓷试样。展开更多
利用室温下弛豫铁电单晶0.93Pb(Zn1/3Nb2/3)O3-0.07PbTiO3的材料参数,计算了[001]c极化PZN-7%PT晶体中的声表面波传播特性。结果表明,[001]c极化0.93Pb(Zn1/3Nb2/3)O3-0.07Pb TiO3单晶具有明显优于传统压电材料的声表面波特性。0.93Pb(Z...利用室温下弛豫铁电单晶0.93Pb(Zn1/3Nb2/3)O3-0.07PbTiO3的材料参数,计算了[001]c极化PZN-7%PT晶体中的声表面波传播特性。结果表明,[001]c极化0.93Pb(Zn1/3Nb2/3)O3-0.07Pb TiO3单晶具有明显优于传统压电材料的声表面波特性。0.93Pb(Zn1/3Nb2/3)O3-0.07Pb Ti O3单晶的声表面波特性随着传播方向发生明显的变化。综合考虑晶体的三种声表面波特性,发现Y切型晶体的综合声表面波性能最好,声表面波机电耦合系数k2值较大,能流角和声表面波自由表面相速度值较小,有望应用于下一代低频声表面波设备中。展开更多
This paper reports that the transverse laser induced thermoelectric voltages （LITV） axe observed for the first time in the step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 （PMN-PT, x = 0.20, 0.33, 0.50） thin fi...This paper reports that the transverse laser induced thermoelectric voltages （LITV） axe observed for the first time in the step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 （PMN-PT, x = 0.20, 0.33, 0.50） thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate （PMN） and lead titanate （PT）, there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength, the largest induced voltage is observed in the 0.50Pb（Mg1/3Nb2/3）O3-0.50 PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated.展开更多
文摘Commercially available niobium (V) oxide [Nb2O5], with barium acetate [Ba(CH3COO)2] and magnesium acetate [Mg(CH3COO)2-4H2O] was used as the starting material in the sol-gel process for preparing Ba(Mg1/3Nb2/3)O3 (BMN) nanopowders. At first, Nb2O5 reacted with melting sodium hydroxide and transformed into dispersible oxide. The resulting glassy substance after cooling was dispersed and washed several times in distilled water to remove the Na+ ions. The as-prepared colloidal Nb2O5-nH2O was subsequently mixed with acetic solution of barium acetate and magnesium acetate according to the required molar proportions and followed by gelation. The ultrafine BMN powders were finally obtained after heat-treating the gel at 820℃for 1 h, and the as-sintered nanoceramics revealed a high relative density of 98.2%, and a high microwave Q-factor, of 10397 at 1.45GHz.
文摘Ba(Mg1/3Nb2/3)O3(BMN)复合钙钛矿陶瓷具有高介电常数和高品质因子等介电性能,预示了其在光学领域的应用前景.本文采用第一性原理方法计算了BMN的电子结构,对其本征光学性能进行分析和预测.对固相合成六方相BMN的XRD测试结果进行Rietveld精修(加权方差因子Rwp=6.73%,方差因子Rp=5.05%),在此基础上建立晶体结构模型并对其进行几何优化.运用基于密度泛函理论(DFT)的平面波赝势方法,对六方相BMN晶体模型的能带、态密度和光学性质进行理论计算.结果表明BMN的能带结构为间接带隙,禁带宽度Eg=2.728 e V.Mg-O和Ba-O以离子键结合为主,Nb-O以共价键结合为主,费米面附近的能带主要由O-2p和Nb-4d态电子占据,形成了d-p轨道杂化.修正带隙后,计算了BMN沿[100]和[001]方向上的复介电函数、吸收系数和反射率等光学性质.结果表明,BMN近乎光学各向同性,在可见光区,其本征透过率为77%<T<83%,折射率为1.91<n<2.14,并伴随一定的色散现象.实验测试结果与理论计算结果相吻合.
文摘基于Swartz and Shrout的二次合成法,采用改进的两步法,将部分原料预合成,一次烧结合成具有100%钙钛矿结构的75Pb(Zn_(1/3)Nb_(2/3))O_3-10PbTiO_3-15BaTiO_3固溶体陶瓷。首先一次性称量PbO,然后和ZnNb_2O_6混合,在660～800℃预合成,将预合成产物粉碎后再与TiO_2和BaCO_3按化学计量称量,充分混合后,在1060～1140℃保温1～2h烧结成陶瓷试样。实验结果表明:改进的两步法工艺能够将预合成温度降为660℃,烧结温度能被拓宽到80℃获得100%钙钛矿结构的固溶体陶瓷。不同于传统的预合成和烧结,改进的两步法工艺简单、有效,在预合成阶段没有形成钙钛矿相,烧结阶段陶瓷的成瓷和致密化同时进行,完成了中间相向钙钛矿相的转变,获得了介电性能优良的陶瓷试样。
文摘利用室温下弛豫铁电单晶0.93Pb(Zn1/3Nb2/3)O3-0.07PbTiO3的材料参数,计算了[001]c极化PZN-7%PT晶体中的声表面波传播特性。结果表明,[001]c极化0.93Pb(Zn1/3Nb2/3)O3-0.07Pb TiO3单晶具有明显优于传统压电材料的声表面波特性。0.93Pb(Zn1/3Nb2/3)O3-0.07Pb Ti O3单晶的声表面波特性随着传播方向发生明显的变化。综合考虑晶体的三种声表面波特性,发现Y切型晶体的综合声表面波性能最好,声表面波机电耦合系数k2值较大,能流角和声表面波自由表面相速度值较小,有望应用于下一代低频声表面波设备中。
基金Project supported by the National Natural Science Foundation of China (Grant No. 10274026)
文摘This paper reports that the transverse laser induced thermoelectric voltages （LITV） axe observed for the first time in the step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 （PMN-PT, x = 0.20, 0.33, 0.50） thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate （PMN） and lead titanate （PT）, there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength, the largest induced voltage is observed in the 0.50Pb（Mg1/3Nb2/3）O3-0.50 PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated.
