Preparation of high active Pt/C cathode electrocatalyst for direct methanol fuel cell by citrate-stabilized method

Platinum nanoparticles supported on carbons（Pt/C,60%,mass fraction） electrocatalysts for direct methanol fuel cell（DMFC） were prepared by citrate-stabilized method with different reductants and carbon supports.The catalysts were characterized by X-ray diffraction（XRD）,transmission electron microscopy（TEM） and cyclic voltammetry（CV）.It is found that the size of Pt nanoparticles on carbon is controllable by citrate addition and reductant optimization,and the form of carbon support has a great influence on electrocatalytic activity of catalysts.The citrate-stabilized Pt nanoparticles supported on BP2000 carbon,which was reduced by formaldehyde,exhibit the best performance with about 2 nm in diameter and 66.46 m2/g（Pt） in electrocatalytic active surface（EAS） area.Test on single DMFC with 60%（mass fraction） Pt/BP2000 as cathode electrocatalyst showed maximum power density at 78.8 mW/cm2.

高活性Pd-Bi/C催化剂催化氧化葡萄糖机理的研究

本工作研制出的高活性、高选择的Pd_Bi/C催化剂 ,用于催化氧化葡萄糖可使葡萄糖酸钠的产率达98%以上 ,选择性高达99.8%。

Pd-Bi/C催化合成丙酮酸的研究

采用液相催化氧化丙酮醛，丙酮醛选择性转化为丙酮酸。探讨了不同载体、反应时间和温度以及催化组分Pd和Bi的添加量对丙酮酸产率的影响。结果表明，当负载Pd2．5％，物质的量比Bi／Pd为0．2，pH7～8，反应温度为45℃左右，反应时间2．5h条件下，丙酮酸产率最高，产率达86．4％。

一种葡萄糖氧化的高效催化剂-Pd-Bi/C

研究了Pd－Bi／C催化剂的合成，Pd－Bi/C催化氧化葡萄糖的性能。结果表明：Pd-Bi/C催化剂催化葡萄糖的产率可达97％以上，选择性可达99％，且重复使用7次后，其产率及选择性仍然基本不变。另外发现：Pd－Bi/C催化剂中，最佳Bi/Pd（mol/mol）比为0．300－0．325。

Ca_(2)Fe_(2)O_(5)催化剂对半焦基DC-SOFC性能的影响

半焦与CO_(2)的气化反应速率是影响半焦燃料基DC-SOFC电池性能的关键。为提高半焦的CO_(2)气化反应性,采用柠檬酸溶胶-凝胶法制备了具有钙钛矿结构的Ca_(2)Fe_(2)O_(5)催化剂,用SEM、XRD、XPS、低温氮气吸脱附等分析手段研究了Ca_(2)Fe_(2)O_(5)催化剂的形貌和结构,采用热重分析实验研究Ca_(2)Fe_(2)O_(5)催化剂对半焦燃料的CO_(2)气化反应催化活性;在Ag-GDC|YSZ|GDC-Ag电解质支撑电池系统上,研究了添加Ca_(2)Fe_(2)O_(5)催化剂对半焦燃料基DC-SOFC输出性能的影响。结果表明,随着催化剂焙烧温度的提高,Ca_(2)Fe_(2)O_(5)催化剂晶粒尺寸逐渐增大、比表面积降低,750℃焙烧的催化剂具有良好的分散性、颗粒尺寸约为0.1μm,在半焦的CO_(2)气化反应中催化作用最好;相较于CaO和Fe2O3,Ca_(2)Fe_(2)O_(5)催化剂结构中吸附氧浓度更高,在半焦的CO_(2)气化反应中表现出更为优异的催化活性;Ca_(2)Fe_(2)O_(5)催化剂的循环稳定性取决于催化剂结构的热稳定性,其循环使用时活性降低主要归因于半焦燃料中无机灰分的包裹。催化剂对DC-SOFC输出性能影响表明,当半焦中添加10%的Ca_(2)Fe_(2)O_(5)催化剂时,电池的峰值功率密度从15.3 mW/cm^(2)增大到23.7 mW/cm^(2);EIS分析表明阳极传质阻力是影响DC-SOFC输出性能和燃料利用率的主要因素,降低灰分、催化剂累积带来的传质阻力可有效提高电池寿命和燃料利用率。

碳笼负载镍基磁性催化剂Ni@Cage-C的制备与性能研究

以自然结晶法制备的ZIF-67为前驱体,采用包裹-刻蚀-碳化策略,得到大小均匀的纳米碳笼(Cage-C),再于液相条件下以碳笼为载体负载上活性金属镍(Ni),成功制备了非贵金属磁性催化剂Ni@Cage-C,并应用于对硝基苯酚催化还原反应以考察其多相催化性能。结果表明:优化条件下制备的Ni@Cage-C催化剂为碳笼包裹单质镍结构,其平均颗粒大小为550 nm;将Ni@Cage-C用于对硝基苯酚催化还原反应时,催化性能明显优于参照催化剂雷尼镍(Raney-Ni)。质量反应速率常数kM为6.11 mg^(-1)·min^(-1),催化效率达到98.87%,循环反应十圈后活性仍高于初始活性的85%。

Preparation of Ultrafine and High Dispersion Pd/C Catalyst and Its Electrocatalytic Performance for Formic Acid Oxidation

A carbon supported Pd（Pd/C） catalyst used as the anodic catalyst in the direct formic acid fuel cells（DFAFC） was prepared via the improved complex reduction method with sodium ethylenediamine tetracetate（EDTA） as stabilizer and complexing agent. This method is very simple. The average size of the Pd particles in the Pd/C catalyst prepared with the improved complex reduction method is as small as about 2.1 nm and the Pd particles in the Pd/C catalyst possess an excellent uniformity. The Pd/C catalyst shows a high electrocatalytic activity and stability for the formic acid oxidation.

Preparation of Pt/C Catalyst with a New and Simple Organic Sol Method

It is reported for the first time that the Pt/C catalyst can be prepared with a new and simple organic sol method using SnCl2 as the reductant. It was found that the average size of the Pt particles in the Pt/C catalysts could be controlled with controlling the preparation conditions. The effect of the average sizes of the Pt particles in the Pt/C catalysts obtained with this method on the electrocatalytical activity of the oxidation of methanol was investigated.

Inhibiting effect of tungstic compounds on glucose hydrogenation over Ru/C catalyst

The effect of acid component including various conventional acids and tungstic compounds on glucose hydrogenation over a series of binary catalyst system containing Ru/C catalyst was investigated. The results showed that HC1, H2SO4, H3BO3, H3PO4, and HNO3 had negligible effect, while all the tungstic compounds imposed inhibiting effects on the hydrogenation of glucose over Ru/C catalyst, and the suppressing effect followed the order of H2WO4〉HPW〉WO3〉AMT〉HSiW. This order is the same as the order of ethylene glycol （EG） yields in the one-pot conversion of glucose to EG, suggesting the important role of competition between glucose hydrogenation and retro-aldol condensation in controlling the selectivity of EG.

Solvent effects on Pt-Ru/C catalyst for methanol electro-oxidation

Alloying degree, particle size and the level of dispersion are the key structural parameters of Pt-Ru/C catalyst in fuel cells. Solvent（s） used in the preparation process can affect the particle size and alloying degree of the object substance, which lead to a great positive impact on its properties. In this work, three types of solvents and their mixtures were used in preparation of the Pt-Ru/C catalysts by chemical reduction of metal precursors with sodium borohydride at room temperature. The structure of the catalysts was characterized by X-ray diffraction （XRD） and Transmission electron microscopy （TEM）. The catalytic activity and stability for methanol electro-oxidation were studied by Cyclic Voltammetry （CV） and Chronoamperometry （CA）. Pt-Ru/C catalyst prepared in H2O or binary solvents of H2O and isopropanol had large particle size and low alloying degree leading to low catalytic activity and less stability in methanol electro-oxidation. When tetrahydrofuran was added to the above solvent systems, Pt-Ru/C catalyst prepared had smaller particle size and higher alloying degree which resulted in better catalytic activity, lower onset and peak potentials, compared with the above catalysts. Moreover, the catalyst prepared in ternary solvents of isopropanol, water and tetrahydrofuran had the smallest particle size, and the high alloying degree and the dispersion kept unchanged. Therefore, this kind of catalyst showed the highest catalytic activity and good stability for methanol electro-oxidation.

Ultrafine Pt nanoparticles supported on double-shelled C/TiO2 hollow spheres material as highly efficient methanol oxidation catalysts

Catalyst support is extremely important for future fuel cell devices.In this work,we developed doubleshelled C/TiO2(DSCT)hollow spheres as an excellent catalyst support via a template-directed method.The combination of hollow structure,TiO2 shell and carbon layer results in excellent electron conductivity,electrocatalytic activity,and chemical stability.These uniformed DSCT hollow spheres are used as catalyst support to synthesize Pt/DSCT hollow spheres electrocatalyst.The resulting Pt/DSCT hollow spheres exhibited high catalytic performance with a current density of 462 mA mg^-1 for methanol oxidation reaction,which is 2.52 times higher than that of the commercial Pt/C.Furthermore,the increased tolerance to carbonaceous poisoning with a higher If/Ibratio and a better long-term stability in acid media suggests that the DSCT hollow sphere is a promising C/TiO2-based catalyst support for direct methanol fuel cells applications.

Construction of bifunctional single-atom catalysts on the optimized β-Mo_(2)C surface for highly selective hydrogenation of CO_(2) into ethanol

Green and economical CO_(2)utilization is significant for CO_(2)emission reduction and energy development.Here,the 1D Mo_(2)C nanowires with dominant(101)crystal surfaces were modified by the deposition of atomic functional components Rh and K.While unmodifiedβMo_(2)C could only convert CO_(2)to methanol,the designed catalyst of K_(0.2)Rh_(0.2)/β-Mo_(2)C exhibited up to 72.1%of ethanol selectivity at 150℃.It was observed that the atomically dispersed Rh could form the bifunctional active centres with the active carrierβMo_(2)C with the synergistic effects to achieve highly specific controlled C–C coupling.By promoting the CO_(2)adsorption and activation,the introduction of an alkali metal(K)mainly regulated the balanced performance of the two active centres,which in turn improved the hydrogenation selectivity.Overall,the controlled modification ofβMo_(2)C provides a new design strategy for the highly efficient,lowtemperature hydrogenation of CO_(2)to ethanol with single-atom catalysts,which provides an excellent example for the rational design of the complex catalysts.

Systematic variation of the sodium/sulfur promoter content on carbon-supported iron catalysts for the Fischer–Tropsch to olefins reaction

The Fischer–Tropsch to olefins（FTO） process is a method for the direct conversion of synthesis gas to lower C–Colefins. Carbon-supported iron carbide nanoparticles are attractive catalysts for this reaction.The catalytic activity can be improved and undesired formation of alkanes can be suppressed by the addition of sodium and sulfur as promoters but the influence of their content and ratio remains poorly understood and the promoted catalysts often suffer from rapid deactivation due to particle growth. A series of carbon black-supported iron catalysts with similar iron content and nominal sodium/sulfur loadings of 1–30/0.5–5 wt% with respect to iron are prepared and characterized under FTO conditions at 1and 10 bar syngas pressure to illuminate the influence of the promoter level on the catalytic properties.Iron particles and promoters undergo significant reorganization during FTO operation under industrially relevant conditions. Low sodium content（1–3 wt%） leads to a delay in iron carbide formation. Sodium contents of 15–30 wt% lead to rapid loss of catalytic activity due to the covering of the iron surface with promoters during particle growth under FTO operation. Higher activity and slower loss of activity are observed at low promoter contents（1–3 wt% sodium and 0.5–1 wt% sulfur） but a minimum amount of alkali is required to effectively suppress methane and C–Cparaffin formation. A reference catalyst support（carbide-derived carbon aerogel） shows that the optimum promoter level depends on iron particle size and support pore structure.

A review of C_1 chemistry synthesis using yttrium-stabilized zirconia catalyst

C1 chemistry based on synthesis gas, methane, and carbon dioxide offers many routes to industrial chemicals. The reactions related to the synthesis of gas can be classified into direct and indirect approach for making such products, such as acetic acid, dimethyl ether, and alcohol. Catalytic syngas processing is currently done at high temperatures and pressures, conditions that could be unfavorable for the life of the catalyst. Another issue of C1 chemistry is related to the methane-initiated process. It has been known that direct methane conversions are still suffering from low yields and selectivity of products resulting in unprofitable ways to produce products, such as higher hydrocarbons, methanol, and so on. However, many experts and researchers are still trying to find the best method to overcome these barriers, for example, by finding the best catalyst to reduce the high-energy barrier of the reactions and conduct only selective catalyst-surface reactions. The appli- cation of Yttria-Stabilized Zirconia （YSZ） and its combination with other metals for catalyzing purposes are increasing. The existence of an interesting site that acts as oxygen store could be the main reason for it. Moreover, formation of intermediate species on the surface of YSZ also contributes significantly in increasing the production of some specific products. Understanding the phenomena happening inside could be necessary. In this article, the use of YSZ for some C1 chemistry reactions was discussed and reviewed.

Scission of C–O and C–C linkages in lignin over RuRe alloy catalyst

The performance of lignin depolymerization is basically determined by the interunit C–O and C–C bonds.Numerous C–O bond cleavage strategies have been developed, while the cleavage of C–C bond between the primary aromatic units remains a challenging task due to the high dissociation energy of C–C bond.Herein, a multifunctional Ru Re alloy catalyst was designed, which exhibited exceptional catalytic activity for the cleavage of both C–O and C–C linkages in a broad range of lignin model compounds(β-1, a-5, 5–5,β-O-4, 4-O-5) and two stubborn lignins(kraft lignin and alkaline lignin), affording 97.5% overall yield of monocyclic compounds from model compounds and up to 129% of the maximum theoretical yield of monocyclic products based on C–O bonds cleavage from realistic lignin. Scanning transmission electron microscopy(STEM) characterization showed that Ru Re(1:1) alloy particles with hexagonal close-packed structure were homogeneously dispersed on the support. Quasi-in situ X-ray photoelectron spectroscopy(XPS), and X-ray absorption spectroscopy(XAS) indicate that Ru species were predominantly metallic state, whereas Re species were partially oxidized;meanwhile, there was a strong interaction between Ru and Re, where the electron transfer from Re to Ru was occurred, resulting in great improvement on the capability of C–O and C–C bonds cleavage in lignin conversion.

Screening of MgO- and CeO_2-Based Catalysts for Carbon Dioxide Oxidative Coupling of Methane to C_(2+) Hydrocarbons

The catalyst screening tests for carbon dioxide oxidative coupling of methane (CO2-OCM) have been investigated over ternary and binary metal oxide catalysts. The catalysts are prepared by doping MgO- and CeO2-based solids with oxides from alkali (Li2O), alkaline earth (CaO), and transition metal groups (WO3 or MnO). The presence of the peroxide (O2-2) active sites on the Li2O2, revealed by Raman spectroscopy, may be the key factor in the enhanced performance of some of the Li2O/MgO catalysts. The high reducibility of the CeO2 catalyst, an important factor in the CO2-OCM catalyst activity, may be enhanced by the presence of manganese oxide species. The manganese oxide species increases oxygen mobility and oxygen vacancies in the CeO2 catalyst. Raman and Fourier Transform Infra Red (FT-IR) spectroscopies revealed the presence of lattice vibrations of metal-oxygen bondings and active sites in which the peaks corresponding to the bulk crystalline structures of Li2O, CaO, WO3 and MnO are detected. The performance of 5%MnO/15%CaO/CeO2 catalyst is the most potential among the CeO2-based catalysts, although lower than the 2%Li2O/MgO catalyst. The 2%Li2O/MgO catalyst showed the most promising C2+ hydrocarbons selectivity and yield at 98.0% and 5.7%, respectively.

Pt-Ru Catalysts Prepared by a Modified Polyol Process for Direct Methanol Fuel Cells

Supported PtRu/C catalysts used in direct methanol fuel cells (DMFCs) were prepared by a new modified polyol method. Transmission electron microscopy (TEM), X-ray diffraction (XRD) and cyclic voltammograms (CVs) were carried out to characterize the morphology, composition and the electrochemical properties of the PtRu/C catalyst. The results revealed that the PtRu nanoparticles with small average particle size (≈2.5 nm), and highly dispersed on the carbon support. The PtRu/C catalyst exhibited high catalytic activity and anti poisoned performance than that of the JM PtRu/C. It is imply that the modified polyol method is efficient for PtRu/C catalyst preparation.

Enhanced stability of highly-dispersed copper catalyst supported by hierarchically porous carbon for long term selective hydrogenation

Copper based catalysts have high potential for the substituent of noble-metal based catalysts as their high selectivity and moderate activity for selective hydrogenation reaction;however,achieving further high catalytic stability is very difficult.In this work,the carbonization process of Cu-based organic frameworks was explored for the synthesis of highly-dispersed Cu supported by hierarchically porous carbon with high catalytic performance for selective hydrogenation of 1,3-butadiene.The porous hierarchy of carbon support and the dispersion of copper nanoparticles can be precisely tuned by controlling the carbonization process.The resultant catalyst carbonized at 600°C exhibits a rather low reaction temperature at 75°C for 100%butadiene conversion with 100%selectivity to butenes,due to its reasonable porous hierarchy and highly-dispersed copper sites.More importantly,unprecedentedly stability of the corresponding Cu catalyst was firstly observed for selective 1,3-butadiene hydrogenation,with both 100%butadiene conversion and 100%butenes selectivity over 120 h of reaction at 75°C.This study verifies that a simply control the carbonization process of metal organic frameworks can be an effective way to obtain Cu-based catalysts with superior catalytic performance for selective hydrogenation reaction.

Comparison on Commercial Application of Two Types of C_8 Aromatics Isomerization Catalysts

The results of commercial application of two types of C_8 aromatics isomerization catalysts under different feed conditions were compared to gain an insight in the techno-economical basis for selecting proper technological route at the plant.The comparison reveals differences in every aspect of feed consumption,unit capacity,product output,product distribution,and unit process parameters depending upon which catalyst type is adopted by the integrated PX complex.The type of aromatics isomerization catalyst has its influence on the plant scale,the construction cost,the process unit capacity and the product cost,with the magnitude of its impact varying with changing feed conditions.

Rapid synthesis of highly active Pt/C catalysts with various metal loadings from single batch platinum colloid

A series of Pt/C catalysts for proton exchange membrane fuel cells(PEMFCs) with various metal loadings is synthesized by a microwave-assisted polyol process via mixing an extremely stable platinum colloid(> 3 months’ shelf life) from single batch preparation with activated carbon ethylene glycol suspension.21 wt%, 42 wt% and 61 wt% Pt loadings are employed to showcase the advantages of the improved polyol process. The ultraviolet(UV)–visible spectra and ζ-potential measurements are conducted to monitor the wet chemistry process during catalyst preparation. The powder X-ray diffraction(XRD), transmission electron microscopy(TEM) and thermogravimetric analysis(TGA) characterizations are carried out on catalysts. The catalyst activities are investigated using electrochemical and single cell tests. The stability of Pt nanoparticle colloid is explored by ORR, cyclic voltammetry(CV) and ζ-potential measurements. The TEM results show the Pt particle sizes of the colloid, and the sizes of the 21 wt%, 42 wt% and 61 wt%Pt/C samples are 2.1–3.9 nm. Because of the high Pt dispersion, the Pt/C catalysts exhibit superior electroactivity toward ORR. In addition, four 61 wt% Pt/C catalysts made from the Pt colloid with 0–3 months’ shelf life show almost the same performance, which exhibits superior stability of the Pt colloid system without surfactant protection.