PHASE3型多功能电能表的应用与常见故障分析

对PHASE 3型全电子式分时电能表的工作原理、校准方法进行分析 ,并就现场运行中经常出现的问题提出处理方法和建议。

基于Phase3对除颤器校准方法的研究

心脏除颤器作为一种医疗急救设备,广泛的应用于急诊、心血管科、ICU等科室,其准确与否显得尤为重要,本文主要利用除颤/起搏监护仪质量检测仪Phase3按照JJF1149-2014《心脏除颤器校准规范》对其进行校准方法的研究。

Biphase-to-monophase structure evolution of Na_(0.766+x)Li_(x)Ni_(0.33-x)Mn_(0.5)Fe_(0.1)Ti_(0.07)O_(2) toward ultradurable Na-ion batteries

Layered composite oxide materials with O3/P2 biphasic crystallographic structure typically demonstrate a combination of high capacities of the O3 phase and high operation voltages of the P2 phase.However,their practical applications are seriously obstructed by difficulties in thermodynamic phase regulation,complicated electrochemical phase transition,and unsatisfactory cycling life.Herein,we propose an efficient structural evolution strategy from biphase to monophase of Na_(0.766+x)Li_(x)Ni_(0.33-x)Mn_(0.5)Fe_(0.1)Ti_(0.07)O_(2) through Li+substitution.The role of Li+substitution not only simplifies the unfavorable phase transition by altering the local coordination of transition metal(TM)cations but also stabilizes the cathode–electrolyte interphase to prevent the degradation of TM cations during battery cycling.As a result,the thermodynamically robust O_(3)-Na_(0.826)Li_(0.06)Ni_(0.27)Mn_(0.5)Fe_(0.1)Ti_(0.07)O_(2) cathode delivers a high capacity of 139.4 mAh g^(-1) at 0.1 C and shows prolonged cycling life at high rates,with capacity retention of 81.6%at 5 C over 500 cycles.This work establishes a solid relationship between the thermodynamic structure evolution and electrochemistry of layered cathode materials,contributing to the development of long-life sodium-ion batteries.

Effect of Sc on Al_(3)Fe phase and mechanical properties of as-cast AA5052 aluminum alloy

The AA5052 aluminum alloy is widely used in automobile and aerospace manufacturing,and with the development of light-weight alloys,it is required that these materials exhibit better mechanical properties.Previous studies have demonstrated that the addition of Sc to aluminum alloys can improve both the microstructure and properties of the alloys.In this study,the effect of Sc on the Fe-rich phase and properties of the AA5052 aluminum alloy was studied by adding 0%,0.05%,0.2%,and 0.3%Sc.The results show that with the increase of Sc,the coarse needle-like Fe-rich phase gradually transforms into Chinese-script and then nearly spherical particles,reduce the size of Fe-rich phase,and refine the grain with increase of high angle grain boundaries(HAGBs).These microstructure changes enhance the strength of the AA5052 alloy through Sc addition.The ductility of the alloy is obviously improved because the addition of a lower amount of Sc changes the morphology of Fe-rich phase from needle-like into a Chinese-script,and it is subsequently reduced as a result of significant increase in HAGBs with increasing Sc content.

Ultrasonic solidification mechanism and optimized application performances of ternary Mg_(71.5)Zn_(26.1)Y_(2.4) alloy

One dimensional(1D) and three dimensional(3D) ultrasound sources were applied to the solidification process of Mg_(71.5)Zn_(26.1)Y_(2.4) alloy.The acoustic spectra were in-situ measured, based on which the cavitation intensities and dynamic solidification mechanism were further investigated. With the increase of ultrasonic dimension and amplitude, the primary Mg_(3)Zn_(6)Y phase was significantly refined from petals to nearly pentagonal shape. The sound field measurements showed that the transient cavitation played a decisive role in generating a high local undercooling, which facilitated the formation of icosahedral clusters and promoted the nucleation of primary Mg_(3)Zn_(6)Y phase. The morphological transition of(α-Mg+Mg_(3)Zn_(6)Y) eutectic from lamellar to anomalous structure occurred under 3D ultrasonic condition. The stable cavitation took the main responsibility because the high pressure excited by nonlinearly oscillating bubbles induced the preferential nucleation of α-Mg phase rather than Mg_(3)Zn_(6)Y phase. As compared with its static values, the tensile strength and compression plasticity of this alloy were increased by the factors of 1.9 and 2.1, and its corrosion resistance was also improved with the corrosion current density decreased by one order of magnitude.

Microstructures of TC21 alloys after hydrogenation and dehydrogenation

Microstructural evolution and phase transformation of hydrogenated and dehydrogenated TC21 alloys were investigated by optical microscopy （OM）, X-ray diffraction （XRD） and transmission electron microscopy （TEM）. XRD peaks ofαandβphases after hydrogenation shifted to low angle because of lattice expansion with the solution of hydrogen atoms. Microstructure of TC21 alloy after hydrogenation changed apparently. Compared to the as-received one, the contrasts of equiaxedαphase and transformedβphase under optical microscope were reversed. In addition, XRD and TEM analyses revealed that hydrides and α′ martensite precipitated fromαandβphases. Bulk of twins and some Ti3Al particles were observed in hydrogenated TC21 alloy, which means that hydrogen led to the redistribution of alloying elements inαandβphase. After dehydrogenation, the microstructure of TC21 alloy was similar to that of the as-received one, which consisted ofαandβphases.

Complementary Pass-Transistor Adiabatic Logic Circuit Using Three-Phase Power Supply

A new low power quasi adiabatic logic,complementary pass transistor adiabatic logic (CPAL),is presented.The CPAL circuit is driven by a new three phase power clock,and its non adiabatic loss on output loads can be effectively reduced by using complementary pass transistor logic and transmission gates.Furthermore,the minimization of the energy consumption can be obtained by choosing the optimal size of bootstrapped nMOS transistors,thus it has more efficient energy transfer and recovery.A three phase power supply generator with a small control logic circuit and a single inductor is proposed.An 8 bit adder based on CPAL is designed and verified.With MOSIS 0 25μm CMOS technology,the CPAL adder consumes only 35% of the dissipated energy of a 2N 2N2P adder and is about 50% of the dissipated energy of a PFAL adder for clock rates ranging from 50 to 200MHz.

Magnetostriction and microstructure of melt-spun Fe_(77)Ga_(23) ribbons prepared with different wheel velocities

A set of stacked ribbons with the composition of Fe77Ga23 were prepared with different wheel velocities of 7 m/s, 12.5 m/s and 25 m/s（named as S7, S12.5 and S25, respectively）. High resolution X-ray diffraction patterns of these ribbons show that all the ribbons present the disordered A2 structure, whereas an additional modified-DO3 phase is detected in S12.5 and S25. S25 has stronger（100） texture than other two samples. Ga K-edge extended X-ray absorption fine structure results indicate that both bond distance and the number of Ga atoms in the second neighbor shell around Ga decrease with increasing wheel velocity. No Ga cluster is detected in the studied ribbons. A short-range ordering Ga-rich phase and large local strain have no obvious influence on magnetostriction of S7. It is believed that both the（100） texture and the additional modified-DO3 phase play a positive role in magnetostrictive properties of Fe77Ga23 ribbons.

Formation mechanism and growth kinetics of TiAl_(3) phase in cold-rolled Ti/Al laminated composites during annealing

Cold-rolled Ti/Al laminated composites were annealed at 525−625℃for 0−128 h,and the interfacial microstructure evolution was investigated.The results indicate that only the TiAl_(3) phase was formed at the Ti/Al interface;most of TiAl_(3) grains were fine equiaxed with average sizes ranging from hundreds of nanometers to several microns and the TiAl_(3) grain size increased with increasing annealing time and/or temperature,but the effect of annealing temperature on the TiAl_(3) grain size was far greater than that of annealing time.The growth of the TiAl_(3) phase consisted of two stages.The initial stage was governed by chemical reaction with a reaction activation energy of 195.75 kJ/mol,and the reaction rate constant of the TiAl_(3) phase was larger as the Ti/Al interface was bonded with fresh surfaces.At the second stage,the growth was governed by diffusion,the diffusion activation energy was 33.69 kJ/mol,and the diffusion growth rate constant of the TiAl_(3) phase was mainly determined by the grain boundary diffusion owing to the smaller TiAl_(3) grain size.

Effect of Pr addition on microstructure and mechanical properties of AZ61 magnesium alloy

To improve the strength, hardness and heat resistance of Mg-6Al-lZn （AZ61） alloy, the effects of Pr addition on the as-cast microstructure and mechanical properties of AZ61 alloy were investigated at room and elevated temperatures by means of Brinell hardness measurement, optical microscope （OM）, scanning electron microscope （SEM）, energy dispersive spectroscopy （EDS）, X-ray diffractometer （XRD） and DNS100 electronic universal testing machine. The results show that the microstructures of Pr-containing AZ61 alloys were refined, with primary,β-MglTAI12 phase distributed homogeneously. When the addition of Pr is up to 1.2wt.%, theβ phase becomes finer, and new needle-like or short-rod shaped AI11Pr3 phase and blocky AIPr phase appear. As a result, optimal tensile properties are obtained. However, greater than 1.2wt.% Pr addition leads to poorer mechanical properties due to the aggregation of the needle-like phase and large size of grains. The present research findings provide a new way for strengthening of magnesium alloys at room and elevated temperatures, and a method of producing thermally-stable AZ61 magnesium alloy.

Effects of rare earth Ce addition on microstructure and mechanical properties of impure copper containing Pb

The effects of rare earth Ce on the microstructure and mechanical properties of impure copper containing Pb were investigated using OM,SEM,EPMA,TEM and tensile testing.TEM and EDS analysis reveal that spherical CePb3 particles form after Ce addition.CePb3 particles,with average size of^3.6μm,homogenously distribute in the Cu matrix.Due to small lattice misfit(~4.62%)with Cu matrix,CePb3 particles can act as effective nucleation sites beneficial to the grain refinement.Pb at grain boundaries seriously deteriorates the mechanical properties of Cu.The tensile strength and the elongation of Cu-0.1 Pb are decreased by 43.1%and 56.7%compared with those of pure copper,respectively.Ce can purify grain boundaries,cause the precipitation of CePb3 particles and refine grain sizes,which contribute to significant improvement of the mechanical properties of Cu.Compared with Cu-0.1Pb,the tensile strength(179 MPa)and the elongation(38.5%)of Cu-0.1Pb-0.3Ce are increased by 117.6%and 151.6%,respectively.

Effect of Ti/B Additions on the Formation of Al_3 Ti of in situ TiB_2/Al Composites

A novel technique for fabricating TiB_2/Al composites in molten aluminum was introduced. The formation mechanism of brittleAl,Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The resultsshow that (l) the brittle Al,Ti particulates are always present in the composites when the molar ratio of Ti to B 'T,:nB is l:2; and (2) theformation of the brittle Al,Ti phase can be avoided entirely from the final product by using a proper 'T,:nB of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the latercase, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot ofAl,Ti (4%), whereas the ultimatetensile stfength of the former is nearly that of the later.

A case study of multi-seam coal mine entry stability analysis with strength reduction method

In this paper,the advantage of using numerical models with the strength reduction method(SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated.A coal mine under variable topography from the Central Appalachian region is used as a case study.At this mine,unexpected roof conditions were encountered during development below previously mined panels.Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-and-pillar panels.Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries.The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations.The SRM-calculated stability factors were compared with observations made during the site visits,and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case.It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.

Mssbauer Effect in Ultrafine Particles with Fe-C Solid Solution,γ-Fe and Fe_3C Phases

Ultrafine particles prepared by evaporating pure Fe in CH4 atmosphere using arc-dischargeheating method, were found to consist of Fe-C solid solution, γ-Fe and Fe3C phases. EfFect of annealing temperature on phase transformation and hyperfine interactions has been investigated by Mossbauer spectroscopy, X-ray diffraction (XRD), differential thermal analysis and thermogravimetry (DTA-TG), transmission electron microscopy (TEM), oxygen determination and vibrating sample magnetometer (VSM) measurements. It was observed that phase transformation of γ-Fe to α-Fe occurs during annealing in vacuum. The mechanism causing the change of hyperfine interactions with annealing temperature differs for Fe-C solution and interstitial compounds. DifFerence of hyperfine interactions of Fe-C solid solution in the starting sample and its annealed samples is ascribed to the improvement of activation of interstitial carbon atoms. Stress-relieving in structure of annealed Fe3C particle can result in a weak influence on hyperfine interactions. Parameters fitted to the Mossbauer spectra show the existence of superparamagnetism in all the samples. Absorbed and combined oxygen on particle surface of the starting sample were determined.

Evolution of TiNi precipitates in TiNi alloy during equal channel angular pressing

The evolution of Ti3Ni4 precipitates in Ti49.2Ni50.8 alloy during equal channel angular pressing(ECAP) and intermediate annealing was investigated by transmission electron microscopy. The solution-treated Ti49.2Ni50.8 alloy was aged at 450 ℃ for 10 to 60 min to obtain Ti3Ni4 precipitates ranging from 37 to 75 nm. After ECAP at 450 ℃ for one pass, Ti3Ni4 precipitates introduced by aging for 10 and 30 min totally dissolve into the matrix;however, those produced by aging for 60 min become smaller. The critical size of Ti3Ni4 precipitates to totally dissolve into matrix is determined to be in the range of 37-68 nm. The dislocation density of ECAP-processed samples depends on the initial size of Ti3Ni4 precipitates after aging. With increasing the duration of initial aging from 10 to 60 min, the dislocation density firstly increases and then decreases.

Dynamic phase transition of ferroelectric nanotube described by a spin-1/2 transverse Ising model

The dynamic phase transition properties for ferroelectric nanotube under a spin-1/2 transverse Ising model are studied under the effective field theory(EFT)with correlations.The temperature effects on the pseudo-spin systems are unveiled in three-dimensional(3-D)and two-dimensional(2-D)phase diagrams.Moreover,the dynamic behaviors of exchange interactions on the 3-D and 2-D phase transitions under high temperature are exhibited.The results present that it is hard to obtain pure ferroelectric phase under high temperature;that is,the vibration of orderly pseudo-spins cannot be eliminated completely.

Thermal Behavior and Lithium Ion Conductivity of L_2O-Al_2O_3-TiO_2-SiO_2-P_2O_5 Glass-ceramics

A lithium ion conductive solid electrolyte, L20-AI203-TiO2-SiO2-P20s glass with NASICON- type structure have been synthesized and transformed into glass-ceramic through thermal-treatment at various temperatures from 700 to 1 000 ~C for 12 h. The differential scanning calorimetry （DSC）, X-ray diffraction （XRD）, scanning electron microscopy （SEM） and complex impedance techniques were employed to characterize the samples. The experimental results indicated that the capability of glass forming in this system is superior to that of L20-A1203-TiO2-PzO~. The glass has an amorphous structure and resultant glass-ceramic mainly consisting of LiTi2（PO4）3 phases. Impurity phases AIPO4, TiO2, TiP207 and unidentified phase were observed. With the enhanced heat-treatment temperature, grain grew gradually and lithium ion conductivity of glass-ceramics increased accordingly, the related impedance semicircles were depressed gradually and even disappeared, which could be analytically explained by the coordinate action of the ＇Constant phase element＇ （CPE） model and the ＇Concept of Mismatch and Relaxation＇ model （CMR）. When the sample is devitrified at 1 000 ~C, the maximum room temperature lithium ion conductivity comes up to 4.1 x 10-4 S/cm, which is suitable for the application as an electrolyte of all-solid-state lithium batteries.

Effect of Sc and Zr on recrystallization behavior of 7075 aluminum alloy

The static recrystallization behavior of 7075 aluminum alloy containing Al_(3)(Sc,Zr)phase prepared by casting and the relationship between recrystallization behavior and mechanical properties were studied.The addition of Sc and Zr made the Sc−Zr−7075 aluminum alloy remain the most of fibrous structure and high-density dislocations formed in the extrusion process,resulting in the recrystallization fraction of the alloy decreasing from 35%to 22%,and the corresponding fraction of substructure increasing from 59%to 67%.The Sc and Zr effectively inhibited the recrystallization behavior of 7075 aluminum alloy mainly,which was attributed to the fact that the existence of fine and coherent Al_(3)(Sc,Zr)phase(r=35 nm,f=1.8×10^(−3))strongly pined the dislocations and grain boundaries,preventing the dislocations from rearranging into sub-grain boundaries and from developing into high angle grain boundaries,and further hindering the formation and growth of recrystallized core of the alloy.

Effects of Ag contents in Sn-xAg lead-free solders on microstructure,corrosion behavior and interfacial reaction with Cu substrate

The effects of Ag on the microstructure and corrosion behavior of pre-soldering Sn-xAg lead-free solders,and on the formation of intermetallic layer of the solders with Cu substrate were investigated.The Ag contents(x)were 0,3.0,3.5,4.0,and5.0 wt.%.The Ag content played a role in the morphology of Ag3 Sn phase in the solders.The microstructure analysis showed that theβ-Sn phase was surrounded by eutectic networks in the 3.0 Ag and 3.5 Ag solders and large plate-like Ag3 Sn formed in the 4.0 Ag and5.0 Ag solders.Nonetheless,the Ag content slightly impacted the corrosion behavior of the as-cast solders as characterized using potentiodynamic polarization test.After soldering,only a single layer of a Cu6 Sn5 intermetallic compound formed at the Sn-xAg/Cu interface.By comparison,the Cu6 Sn5 intermetallic layer of the Ag-doped solders was thinner than that of the 0Ag solder.The fine Ag3 Sn particles in the eutectic networks precipitating in the 3.0 Ag and 3.5 Ag solders effectively hindered the growth of Cu6 Sn5 grains compared to large plate-like Ag3 Sn in the 4.0 and 5.0Ag solders.

New Phase Ti_3Co_2Si in the Ti-Co-Si Ternary System at 1100℃

A new phase with the appropriate composition of Ti_3Co_2Si is found to exist at 1100℃. The X-ray diffraction of this phase can not be indexed by any other phase in the Ti-Co-Si ternary system and show this phase to be hexagonal with the lattice parameter of α=0.676 nm, c=0.732 nm, c/α=1.0825.