In vitro corrosion and biocompatibility of phosphating modified WE43 magnesium alloy

Phospahting coated WE43 magnesium alloy was prepared by an immersion method. The microstructure, corrosion resistance and biocompatibility of the coated alloy were investigated. Scanning electron microscopy （SEM） and X-ray diffraction （XRD） were used to examine the microstructure and the composition of the coated alloy. The corrosion resistance was studied by means of potentiodynamic polarization method and the biocompatibility of the surface modified WE43 alloy was evaluated by （3-（4,5）-Dimethylthiazol-2, yl）-2,5-diphenyltetrazolium bromide （MTT） and hemolysis test. The results show that the phosphating coating can enhance the corrosion resistance of WE43 alloy and can be a good candidate to increase the biocompatibility of WE43 alloy.

Self-healing mechanism of composite coatings obtained by phosphating and silicate sol post-sealing

Silicate sol post-treatment was applied to form a complete composite coating on the phosphated zinc layer. The chemical compositions of the coatings were investigated using XPS. The coated samples were firstly scratched and then exposed to the neutral salt spray(NSS) chamber for different time. The microstructure and chemical compositions of the scratches were studied using SEM and EDS. And the non-scratched coated samples were compared. The self-healing mechanism of the composite coatings was discussed. The results show that during corrosion, the self-healing ions in composite coatings dissolve, diffuse and transfer to the scratches or the defects, and then recombine with Zn2+ to form insoluble compound, which deposits and covers the exposed zinc. The corrosion products on the scratches contain silicon, phosphorous, oxygen, chloride and zinc, and they are compact, fine, needle and flake, effectively inhibiting the corrosion formation and expansion of the exposed zinc layer. The composite coatings have good self-healing ability.

Effects of Hydroxylamine Sulfate and Sodium Nitrite on Microstructure and Friction Behavior of Zinc Phosphating Coating on High Carbon Steel

Hydroxylamine sulfate （HAS） and sodium nitrite are used as the accelerators for zinc phos- phate coating on high carbon steel. Phase evolution of phosphate coating was investigated by X-ray diffraction. It is found that the phosphating coatings are mainly composed of hopeite Zn3Fe（PO4）2.4H2O and phosphophyllite Zn2Fe（PO4）2.4H2O. The microstructural changes of the phosphate coating, as a function of phosphating time, were evaluated by scanning elec- tron microscopy. Four-ball friction experiments reveal that hydroxylamine sulfate instead of sodium nitrite can effectively reduce the friction coefficient of lubricated phosphating coat- ing. Therefore, it may be expected that HAS will be widely used as a fast and ECO-friendly accelerator in phosphate industry.

Zinc phosphating of 6061-Al alloy using REN as additive

Zinc phosphate coating formed on 6061-A1 alloy was studied with the help of electrochemical measurements, Fourier Transform Infrared （FTIR）, and Scanning Electron Microscopy （SEM）, after dipping it in phosphating solutions containing different concentrations of Rare Earth Nitrate （REN）. REN, which acted as an accelerator in the phosphating solution, could catalyze the surface reaction and accelerate the phosphating process. REN mainly enabled the P in the phosphate coating to exist in the form of PO4^3- and promoted the hydrolysis of phosphatic acid in a liquid layer at the cathodes. This resulted in the evolution of H2 at the cathodes, which increased the local pH value and in turn drove the precipitation of the phosphate coating. Additionally, REN was adsorbed on the surface of the aluminum substrates to form a gel during the phosphating process. These gel particles were good crystal seeds, which helped to form phosphate crystal nuclei and possess the function of a nucleation agent that could decrease the phosphate crystal size. The corrosion resistance of the formed zinc phosphate coatings was improved.

Composition and Performance of the Composite Coatings Obtained by Phosphating and Cerium Nitrate Post-Sealing on Galvanized Steel

To improve the corrosion resistance of phosphate coatings, the phosphated hot-dip galvanized (HDG) steel was post-sealed with cerium nitrate solution. The morphology, composition, corrosion resistance of the coatings was investigated by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and neutral salt spray (NSS) tests. The results show that after post-sealing the phosphated HDG samples with cerium nitrate solution, the pores among the zinc phosphate crystals are sealed by the compounds containing phosphorus, oxygen and cerium; the zinc phosphate crystals are covered by the flocculent cerium compounds; and the continuous composite coatings are formed on HDG steel. The corrosion resistance of the composite coatings, which increases with the increase in phosphating time and cerium nitrate post-sealing time, is far higher than that of the single phosphate coatings. The composite coatings with the optimal corrosion resistance are obtained for phosphating 300 s and post-sealing 300 s; and the corrosion resistance is more outstanding than that of the chromate coatings.

Self-healing Performance of Composite Coatings Prepared by Phosphating and Cerium Nitrate Post-sealing

The phosphated and cerium nitrate post-sealed galvanized steel was firstly scratched to expose zinc layer and then placed in neutral salt spray （NSS） chamber for different durations. The microstructure and compositions of the scratches were investigated using SEM and EDS. The phases of the corrosion products were examined through XRD. The self-healing mechanism of the composite coatings was discussed. The experimental results show that the composite coatings have an excellent corrosion resistance. The corrosion products increase with corrosion time and finally cover the whole scratch. They contain phosphorous, cerium, oxygen, chloride and zinc, and are fine needle and exceedingly compact. The composite coatings are favorable self-healing. During corrosion, the self-healing ions such as Ce3＋, Ce4＋, PO43-, Zn2＋ in the composite coatings were dissolved, migrated, recombined, and covered the exposed zinc, impeding zinc corrosion. The self-healing process of the scratches on the composite coatings can be divided into three stages, about 2 h, 4 h, and 24 h, respectively.

Study on phosphating treatment of aluminum alloy:role of yttrium oxide

Zinc phosphate coatings formed on 6061-Al alloy, after dipping in phosphating solutions containing different amounts of Y2O3（yttrium oxide）, were studied by scanning electron microscopy （SEM）, X-ray diffraction （XRD） and electrochemical measurements. Significant variations in the morphology and corrosion resistance afforded by zinc phosphate coating were especially observed as Y2O3 in phosphating solution varied from 0 to 40 mg/L. The addition of Y2O3 changed the initial potential of the interface between aluminum alloy substrate and phosphating solution and increased the number of nucleation sites. The phosphate coating thereby was less porous structure and covered the surface of aluminum alloy completely within short phosphating time. Phosphate coating was mainly composed of Zn3（PO4）2·4H2O （hopeite） and AlPO4（aluminum phosphate）. Y2O3, as an additive of phosphatization, accelerated precipitation and refined the gain size of phosphate coating. The corrosion resistance of zinc phosphate coating in 3% NaCl solution was improved as shown by polarization measurement. In the present research, the optimal amount of Y2O3 was 10-20 mg/L, and the optimal phosphating time was 600 s.

Novel interface engineering of LDH-based materials on Mg alloy for efficient photocatalytic systems considering the geometrical linearity of condensed phosphates

This study presents a facile and rapid method for synthesizing novel Layered Double Hydroxide(LDH)nanoflakes,exploring their application as a photocatalyst,and investigating the influence of condensed phosphates'geometric linearity on their photocatalytic properties.Herein,the Mg O film,obtained by plasma electrolysis of AZ31 Mg alloys,was modified by growing an LDH film,which was further functionalized using cyclic sodium hexametaphosphate(CP)and linear sodium tripolyphosphate(LP).CP acted as an enhancer for flake spacing within the LDH structure,while LP changed flake dispersion and orientation.Consequently,CP@LDH demonstrated exceptional efficiency in heterogeneous photocatalysis,effectively degrading organic dyes like Methylene blue(MB),Congo red(CR),and Methyl orange(MO).The unique cyclic structure of CP likely enhances surface reactions and improves the catalyst's interaction with dye molecules.Furthermore,the condensed phosphate structure contributes to a higher surface area and reactivity in CP@LDH,leading to its superior photocatalytic performance compared to LP@LDH.Specifically,LP@LDH demonstrated notable degradation efficiencies of 93.02%,92.89%,and 88.81%for MB,MO,and CR respectively,over a 40 min duration.The highest degradation efficiencies were observed in the case of the CP@LDH sample,reporting 99.99%for MB,98.88%for CR,and 99.70%for MO.This underscores the potential of CP@LDH as a highly effective photocatalyst for organic dye degradation,offering promising prospects for environmental remediation and water detoxification applications.

Study on Phosphating by Ultrasonic Wave at Room Temperature for Sintered NdFeB Magnet

The corrosion behavior of a NdFeB magnet obtained at room temperature,with and without ultrasonic were investigated.The corrosion resistance was investigated by corrosion immersion tests in 3 wt%neutral NaCl solutions,potentiodynamic polarization tests and electrochemical impedance spectroscopy(EIS).The morphology of the conversion coatings on NdFeB surface were analyzed by scanning electron microscopy(SEM).And the forming mechanism of coatings was studied by potential-time curves.The tests of corrosion resistances show that the combination of phosphating treatment with ultrasonic will further improve the corrosion resistance of the NdFeB.The SEM also confirms that phosphating coating under ultrasonic is more homogeneous and compact.

Phosphating-induced charge transfer on CoO/CoP interface for alkaline H_(2)evolution

Designing non-noble metal electrocatalysts toward alkaline hydrogen evolution reaction(HER)with high performance at a large current density is urgent.Herein,a CoO/CoP heterostructure catalyst(termed POZ)was designed by a phosphating strategy.The strong electron transfer on the interface of CoO/CoP was experimentally and theoretically proven.POZ showed a low overpotential of 236 mV at 400 mA/cm^(2),which was 249 mV lower than non-phosphated sample.It also exhibited a remarkable solar-to-hydrogen conversion efficiency of 10.5%.In this work,the construction of CoO/CoP interface realized by a simple phosphating strategy could provide an important reference to boost the HER performance on those materials not merely metal oxides.

Predicting the Degradability of Bioceramics through a DFT-based Descriptor

Bioceramics have attracted extensive attention for bone defect repair due to their excellent bioactivity and degradability.However,challenges remain in matching the rate between bioceramic degradation and new bone formation,necessitating a deeper understanding of their degradation properties.In this study,density functional theory(DFT)calculations was employed to explore the structural and electronic characteristics of silicate bioceramics.These findings reveal a linear correlation between the maximum isosurface value of the valence band maximum(VBMFmax)and the degradability of silicate bioceramics.This correlation was subsequently validated through degradation experiments.Furthermore,the investigation on phosphate bioceramics demonstrates the potential of this descriptor in predicting the degradability of a broader range of bioceramics.This discovery offers valuable insights into the degradation mechanism of bioceramics and holds promise for accelerating the design and development of bioceramics with controllable degradation.

Efficient Removal of Phosphate from Aqueous Solutions Using Corundum-hollow-spheres Supported Caclined Hydrotalcite Porous Thin Films

Phosphate was removed from aqueous environment by corundum-hollow-spheres supported caclined hydrotalcite (cHT) thin films. Mg-Al-CO3 hydrotalcite (HT) thin films were deposited on corundumhollow-sphere substrates by hydrothermal homogeneous precipitation at 120℃for 30-240 min and cHT thin films were obtained by annealing of the HT thin films at 500℃for 180 min. Their crystal phase, morphology and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM).The results show that homogeneous, well-crystallized and hierarchical flower-like thin films were deposited firmly on the surface of the corundum. The mechanism of nucleation and growth of the HT thin films was fitted well with the anion coordination polyhedron growth unit model. To determine the absorption of phosphate by this adsorbent, different bed depth (10-30 cm) and flow rate (1.0-3.0 m L/min) were examined by column experiments. The highest removal efficiency of phosphate amounted to 98.5%under optimum condition (pH=7.2). The adsorption capacity increased as the bed depth increased and decreased as the flow rate increased.

Effect of Fluoride on the Ion-association of Calcium Phosphate and Crystallization of Hydroxyapatite

Using a titration setup to accurately control the reaction conditions and in situ monitor the reaction,we showed that fluoride exhibited negligible effects on the ion association process of calcium and phosphate and the formation of ACP nanospheres in a buffer solution with constant ionic strength.However,the stability of ACP increased with increasing fluoride concentration,which was ascribed to the inhibitory effect of fluoride on the aggregation of ACP nanospheres and the nucleation of nanocrystals on the surface of ACP nanospheres.Furthermore,fluoride could inhibit the lateral growth of HAP nanosheets and promote the formation of rod-like crystals.These results further improve our understanding of the crystallization pathway of HAP crystals and the regulatory effects of fluoride.

Surface-neutralization engineered NiCo-LDH/phosphate hetero-sheets toward robust oxygen evolution reaction

Developing highly active oxygen evolution reaction(OER)electrocatalysts with robust durability is essential in producing high-purity hydrogen through water electrolysis.Layered double hydroxide(LDH)based catalysts have demonstrated efficient catalytic performance toward the relatively sluggish OER.By considering the promotion effect of phosphate(Pi)on proton transfer,herein,a facile phosphate acid(PA)surface-neutralization strategy is developed to in-situ construct NiCo-LDH/NiCoPi hetero-sheets toward OER catalysis.OER activity of NiCoLDH is significantly boosted due to the proton promotion effect and the electronic modulation effect of NiCoPi.As a result,the facilely prepared NiCo-LDH/NiCoPi catalyst displays superior OER catalytic activity with a low overpotential of 300 mV to deliver 100 mA cm^(-2)OER and a Tafel slope of 73 mV dec^(-1).Furthermore,no visible activity decay is detected after a 200-h continuous OER operation.The present work,therefore,provides a promising strategy to exploit robust OER electrocatalysts for commercial water electrolysers.

Enhancing sustainability in phosphate ore processing:Performance of frying oil as alternative flotation collector for carbonate removal

Recycling waste frying oils for the synthesis of flotation reagents presents a promising avenue for sustainable waste management.Moreover,it offers a cost-effective solution for crafting a specialized collector designed to efficiently remove carbonates and enhance phosphate enrichment in froth flotation processes.This study focuses on the synthesis of an anionic collector using the saponification reaction of a frying oil sample,subsequently applied to the flotation of calcite and dolomite.To elucidate the adsorption mechanisms of the frying oil collector(FrOC)and sodium oleate,a reference collector,on fluorapatite,calcite,dolomite,and quartz surfaces,comprehensive experiments were conducted,including zeta potential measurements and Fourier transform infrared spectroscopy.Results revealed diverse adsorption affinities of the molecules towards these minerals.To assess the practical performance of the collector,flotation tests were conducted using a natural phosphate ore mixture,employing a BoxBehnken experimental design.Notably,under optimized conditions(pH 9,1000 g/t of FrOC,3.5 min of conditioning,and 6 min of flotation),FrOC exhibited excellent performance,with calcite and dolomite recoveries exceeding 80%,while apatite recovery in the concentrate fraction remained below 10%.This work exemplifies both circular economy practices and the distinctive approach to sustainable mineral processing.

In-situ construction of abundant active centers on hierarchically porous carbon electrode toward high-performance phosphate electrosorption: Synergistic effect of electric field and capture sites

Phosphate removal is crucial for eutrophication control and water quality improvement.Electro-assisted adsorption,an eco-friendly elec-trosorption process,exhibited a promising potential for wastewater treatment.However,there are few works focused on phosphate electro-sorption,and reported electrodes cannot attach satisfactory removal capacities and rates.Herein,electro-assisted adsorption of phosphate via in-situ construction of La active centers on hierarchically porous carbon(LaPC)has been originally demonstrated.The resulted LaPC composite not only possessed a hierarchically porous structure with uniformly dispersed La active sites,but also provided good conductivity for interfacial electron transfer.The LaPC electrode achieved an ultrahigh phosphate electrosorption capability of 462.01 mg g^(-1) at 1 V,outperforming most existing electrodes.The superior phosphate removal performance originates from abundant active centers formed by the coupling of electricfield and capture sites.Besides,the stability and selectivity toward phosphate capture were maintained well even under comprehensive conditions.Moreover,a series of kinetics and isotherms models were employed to validate the electrosorption process.This work demonstrates a deep understanding and promotes a new level of phosphate electrosorption.

Preparation and interface state of phosphate tailing-based geopolymers

The long-term storage of phosphate tailings will occupy a large amount of land,pollute soil and groundwater,thus,it is crucial to achieve the harmless disposal of phosphate tailings.In this study,high-performance geopolymers with compressive strength of 38.8 MPa were prepared by using phosphate tailings as the main raw material,fly ash as the active silicon-aluminum material,and water glass as the alkaline activator.The solid content of phosphate tailings and fly ash was 60% and 40%,respectively,and the water-cement ratio was 0.22.The results of XRD,FTIR,SEM-EDS and XPS show that the reactivity of phosphate tailings with alkaline activator is weak,and the silicon-aluminum material can react with alkaline activator to form zeolite and gel,and encapsulate/cover the phosphate tailings to form a dense phosphate tailings-based geopolymer.During the formation of geopolymers,part of the aluminum-oxygen tetrahedron replaced the silicon-oxygen tetrahedron,causing the polycondensation reaction between geopolymers and increasing the strength of geopolymers.The leaching toxicity test results show that the geopolymer has a good solid sealing effect on heavy metal ions.The preparation of geopolymer from phosphate tailings is an important way to alleviate the storage pressure and realize the resource utilization of phosphate tailings.

Differential roles of C-3 and C-6 phosphate monoesters in affecting potato starch properties

The effects of starch phosphate monoester content(SPC),namely C-3(C3P)and C-6 phosphate monoesters(C6P),on the starch properties were investigated using four potato starches with varied SPC/C3P/C6P and two nonphosphorylated maize starches with a similar range of amylose content(AC)as controls.The starch property results showed that a higher SPC is associated with lower turbidity,storage and loss modulus after storage,and water solubility,but higher swelling power(SP)and pasting viscosities.These findings suggested that SPC inhibited molecular rearrangement during storage and starch leaching during heating,and enhanced swelling and viscosities due to increased hydration and water uptake caused by the repulsion effect of phosphate groups and a less ordered crystalline structure.Increased SPC also resulted in lower resistant starch(RS)content in a native granular state but higher RS after retrogradation.Pearson correlations further indicated that SPC/C3P/C6P were positively correlated with peak(r^(2)=0.925,0.873 and 0.930,respectively),trough(r^(2)=0.994,0.968 and 0.988,respectively),and final viscosities(r^(2)=0.981,0.968 and 0.971,respectively).Notably,SPC,mainly C3P,exhibited a significantly positive correlation with SP(r^(2)=0.859)and setback viscosity(r^(2)=0.867),whereas SPC,mainly C6P,showed a weak positive correlation with RS after retrogradation(r^(2)=0.746).However,SPC had no significant correlations with water solubility,turbidity and rheology properties,which were more correlated with AC.These findings are helpful for the food industry to select potato starches with desired properties based on their contents of SPC,C3P,or C6P.

Immunomodulatory activity of polycaprolactone nanoparticles with calcium phosphate salts against Leishmania infantum infection

Objective:To prepare and characterize polycaprolactone(PCL)nanoparticles loaded with sonicator fragmented(SLA)and freeze-thaw Leishmania antigens(FTLA)and to investigate the in vitro immunogenicity of antigen-encapsulated nanoparticles with calcium phosphate adjuvant.Methods:The water/oil/water binary emulsion solvent evaporation method was used to synthesize antigen-loaded PCL nanoparticles.Particles were characterized by scanning electron microscopy and zeta potential measurements.Their cytotoxicity in J774 macrophages in vitro was determined by MTT analysis.In addition,the amount of nitric oxide and the level of cytokines produced by macrophages were determined by Griess reaction and ELISA method,respectively.The protective effect of the developed formulations was evaluated by determining the infection index percentage in macrophages infected with Leishmania infantum.Results:Compared to the control group,SLA PCL and FTLA PCL nanoparticles with calcium phosphate adjuvant induced a 6-and 7-fold increase in nitric oxide,respectively.Additionally,the vaccine formulations promoted the production of IFN-γand IL-12.SLA PCL and FTLA PCL nanoparticles combined with calcium phosphate adjuvant caused an approximately 13-and 11-fold reduction in infection index,respectively,compared to the control group.Conclusions:The encapsulation of antigens obtained by both sonication and freeze-thawing into PCL nanoparticles and the formulations with calcium phosphate adjuvant show strong in vitro immune stimulating properties.Therefore,PCL-based antigen delivery systems and calcium phosphate adjuvant are recommended as a potential vaccine candidate against leishmaniasis.

Research,application and development of inorganic binder for casting process

Inorganic binder used in casting process has the advantages of low odor,labor-friendly conditions,and relatively low cost,which is one of the main development directions for casting molding materials in the future.However,compared to organic binders(such as resin binders),inorganic binders exhibit lower bonding strength and are more sensitive to environmental humidity.This sensitivity poses challenges,particularly in the reclamation of used sand,thus limiting their broader application.In this paper,the research and application status of inorganic binders(mainly silicate inorganic binders)and their curing methods are summarized.In addition,the research and application of phosphate inorganic binders and 3D printing inorganic binders that are being developed are introduced.Meanwhile,a detailed comparative analysis is conducted on the challenging issue of“reclamation for used sand”in the application of inorganic binders.Finally,the development direction of inorganic binders is clarified.