Performance Analysis of Compound Parabolic Concentration Photothermal and Photoelectricity Device for Soil Heating in Facility Agriculture

It is difficult for solanum crops to grow continuously during winter in severe cold regions. Thus, a soil heating system for facility agriculture based on solar concentration technology was proposed, and a novel compound parabolic concentration photothermal and photoelectricity device(CTPV) equipped in the system was designed to address this problem. In accordance with the structure of the device, LightTools optical software was selected to analyze the variation trend of the light escape rate of the device with the diff erent incident angles. On the basis of the calculation results, an experimental test system was used to investigate the relationship of the air temperature of the inlet and the outlet, total output power of the solar cells, and photothermal and photoelectricity efficiency of the device with the operation time during a sunny day. Research results reveal that the light escape rate of the device is 5.36% at an incidence angle of 12°. At a velocity of 1.5 m/s, the maximum air temperature of the outlet can reach 55.6 ℃, and the total output power of the solar cells is 474.4 W. The variation of the total power of the solar cells is consistent with the simulation results. The maximum instantaneous heat collection and the maximum photothermal and photoelectricity efficiency of the device are 306 W and 60.4%, respectively, and the average efficiency is 44.9%. This study can serve as a reference for compound parabolic concentration technology applied for soil heating in facility agricultural soil heating systems.

Mn^(4+) activated phosphors in photoelectric and energy conversion devices

Owing to their high luminous efficiency and tunable emission in both red light and far-red light regions,Mn^(4+)ion-activated phosphors have appealed significant interest in photoelectric and energy conversion devices such as white light emitting diode(W-LED),plant cultivation LED,and temperature thermometer.Up to now,Mn^(4+)has been widely introduced into the lattices of various inorganic hosts for brightly redemitting phosphors.However,how to correlate the structure-activity relationship between host framework,luminescence property,and photoelectric device is urgently demanded.In this review,we thoroughly summarize the recent advances of Mn^(4+)doped phosphors.Meanwhile,several strategies like co-doping and defect passivation for improving Mn^(4+)emission are also discussed.Most importantly,the relationship between the protocols for tailoring the structures of Mn^(4+)doped phosphors,increased luminescence performance,and the targeted devices with efficient photoelectric and energy conversion efficiency is deeply correlated.Finally,the challenges and perspectives of Mn^(4+)doped phosphors for practical applications are anticipated.We cordially anticipate that this review can deliver a deep comprehension of not only Mn^(4+)luminescence mechanism but also the crystal structure tailoring strategy of phosphors,so as to spur innovative thoughts in designing advanced phosphors and deepening the applications.

Thickness effect on solar-blind photoelectric properties of ultrathinβ-Ga_(2)O_(3)films prepared by atomic layer deposition

Theβ-Ga_(2)O_(3)films with different thicknesses are prepared by an atomic layer deposition system.The influence of film thickness on the crystal quality is obvious,indicating that the thicker films perform better crystal quality,which is verified from x-ray diffraction(XRD)and scanning electron microscope(SEM)results.The Ga_(2)O_(3)-based solar blind photodetectors with different thicknesses are fabricated and studied.The experimental results show that the responsivity of the photodetectors increases exponentially with the increase of the film thickness.The photodetectors with inter-fingered structure based on 900 growth cyclesβ-Ga_(2)O_(3)active layers(corresponding film thickness of 58 nm)exhibit the best performances including a low dark current of 134 fA,photo-to-dark current ratio of 1.5×10^(7),photoresponsivity of 1.56 A/W,detectivity of 2.77×10^(14)Jones,and external quantum efficiency of 764.49%at a bias voltage of 10 V under 254-nm DUV illumination.The photoresponse rejection ratio(R_(254)/R_(365))is up to 1.86×10^(5).In addition,we find that the photoelectric characteristics also depend on the finger spacing of the MSM structure.As the finger spacing decreases from 50μm to10μW,the photoresponsivity,detectivity,and external quantum efficiency increase significantly.

Effect of thickness of antimony selenide film on its photoelectric properties and microstructure

Antimony selenide(Sb2Se3) films are widely used in phase change memory and solar cells due to their stable switching effect and excellent photovoltaic properties. These properties of the films are affected by the film thickness. A method combining the advantages of Levenberg–Marquardt method and spectral fitting method(LM–SFM) is presented to study the dependence of refractive index(RI), absorption coefficient, optical band gap, Wemple–Di Domenico parameters, dielectric constant and optical electronegativity of the Sb2Se3films on their thickness. The results show that the RI and absorption coefficient of the Sb2Se3films increase with the increase of film thickness, while the optical band gap decreases with the increase of film thickness. Finally, the reasons why the optical and electrical properties of the film change with its thickness are explained by x-ray diffractometer(XRD), energy dispersive x-ray spectrometer(EDS), Mott–Davis state density model and Raman microstructure analysis.

In-fiber photoelectric device based on graphene-coated tilted fiber grating

Graphene and related two-dimensional materials have attracted great research interests due to prominently optical and electrical properties and flexibility in integration with versatile photonic structures.Here,we report an in-fiber photoelec-tric device by wrapping a few-layer graphene and bonding a pair of electrodes onto a tilted fiber Bragg grating(TFBG)for photoelectric and electric-induced thermo-optic conversions.The transmitted spectrum from this device consists of a dense comb of narrowband resonances that provides an observable window to sense the photocurrent and the electrical injection in the graphene layer.The device has a wavelength-sensitive photoresponse with responsivity up to 11.4 A/W,allowing the spectrum analysis by real-time monitoring of photocurrent evolution.Based on the thermal-optic effect of electrical injection,the graphene layer is energized to produce a global red-shift of the transmission spectrum of the TF-BG,with a high sensitivity approaching 2.167×10^(4)nm/A^(2).The in-fiber photoelectric device,therefore as a powerful tool,could be widely available as off-the-shelf product for photodetection,spectrometer and current sensor.

On the Physical Process and Essence of the Photoelectric Effect

A hundred years ago, Planck and Einstein and others created quantum theories or quantum mechanics while they explained the photoelectric effect. Planck and Einstein empirically obtained a statistical relationship between the energy of light quantum and the frequency of light but have not studied the physical process and essence of the photoelectric effect, so some photoelectric phenomena are difficult to be explained by existing quantum mechanics currently. In this paper, a dynamical process of orthogonal interaction between a photon and an electron to form a new state of matter in photoelectric effect experiments is studied so finding that the Planck constant is a product value of the mass, length, and velocity of a high-energy particle. The dynamics of the orthogonal collision of matter (particles) can not only give the physical process and essence of the photoelectric effect, but also have great significance for the further development of quantum mechanics. It can physically explain phenomena such as wave-particle duality and quantum entanglement in the motion of high-energy particles. Its prospects can be widely used in cosmic physics, macro physics, and micro physics.

Study on the Reparative Effect of Peptide RW3 Binding Active Collagen after Photoelectric Skincare

The photoelectric microneedle treatment instrument is also widely used due to the rapid development of medical cosmetology in China in recent years. It also causes a lot of skin discomfort after the consumers carry out such projects. This study, which combines small molecule active peptides (RW3) and active collagens and imitates the photoelectric treatment through in vitro and in vivo experiment, finds that small molecule active peptides (RW3) and active collagens have different improvement effects on cell proliferation, migration, anti-UV damage, inhibition of ear swelling and inflammation in mice, repair of UV damage and skin damage caused by microneedles. .

Performance evaluation and optimization design of photoelectric pyrometer detection optical system

The measurement and control of high temperature play very important roles in national defense,military,scientific experiments,industrial and agricultural production.Photoelectric pyrometer is one of the important radiation thermometers for non-contact temperature measurement.It has an important application in the field of high temperature measurement,and its performance directly affects the accuracy of temperature measurement.By improving the design of the detection optical system of the photoelectric pyrometer,the imaging performance of the photoelectric pyrometer can be improved effectively,and the temperature measurement accuracy can be improved.In this paper,the temperature measurement principle of photoelectric pyrometer,the wo rking principle of the detection optical system and the composition of the system are introduced.The optical components that affect the imaging of the optical system of the photoelectric pyrometer are analyzed.The optical pyrometer detection optical system is simulated by ZEMAX software,based on the analysis results,the Modulation Transfer Function(MTF)and the spot Diagram are used as the main evaluation criteria to optimize the design of the objective lens of the photoelectric pyrometer detection optical system.The imaging performance of the photoelectric pyrometer detection optical system and the accuracy of temperature measurement of the photoelectric pyrometer are improved by optimization design of the detection optical system.

Memristive Artificial Synapses for Neuromorphic Computing

Neuromorphic computing simulates the operation of biological brain function for information processing and can potentially solve the bottleneck of the von Neumann architecture.This computing is realized based on memristive hardware neural networks in which synaptic devices that mimic biological synapses of the brain are the primary units.Mimicking synaptic functions with these devices is critical in neuromorphic systems.In the last decade,electrical and optical signals have been incorporated into the synaptic devices and promoted the simulation of various synaptic functions.In this review,these devices are discussed by categorizing them into electrically stimulated,optically stimulated,and photoelectric synergetic synaptic devices based on stimulation of electrical and optical signals.The working mechanisms of the devices are analyzed in detail.This is followed by a discussion of the progress in mimicking synaptic functions.In addition,existing application scenarios of various synaptic devices are outlined.Furthermore,the performances and future development of the synaptic devices that could be significant for building efficient neuromorphic systems are prospected.

Photoelectric detection technology of laser seeker signals

The measurement of the rolling angle of the projectile is one of the key technologies for the terminal correction projectile.To improve the resolution accuracy of the rolling angle in the laser seeker weapon system, the imaging model of the detector, calculation model of the position and the signal-to-noise ratio(SNR) model of the circuit are built to derive both the correlation between the resolution error of the rolling angle and the spot position, and the relation between the position resolution error and the SNR. Then the influence of each parameter on the SNR is analyzed at large,and the parameters of the circuit are determined. Meanwhile, the SNR and noise voltage of the circuit are calculated according to the SNR model and the decay model of the laser energy. Finally,the actual photoelectric detection circuit is built, whose SNR is measured to be up to 53 d B. It can fully meet the requirement of0.5° for the resolution error of the rolling angle, thereby realizing the analysis of critical technology for photoelectric detection of laser seeker signals.

Performance of a plastic scintillation fiber dosimeter based on different photoelectric devices

The photoelectric device of a scintillation dosimeter converts photons produced by radiation into an electrical signal.Its features directly determine the overall performance of the dosimeter.For a plastic scintillation fiber dosimeter(PSFD)with a current readout mode,systematic studies of the stability and light-dose response were performed for the photomultiplier tube(PMT),silicon photomultiplier(SiPM),avalanche photodiode(APD),and photodiode(PD).The temperature stability,long-term stability,repeatability,signal-to-noise ratio(SNR),and current dose response of the PSFD with the abovementioned photoelectric devices were studied using a pulsed LED light source and the Small Animal Radiation Therapy platform.An exponential relationship between the dark/ne current and temperature was obtained for all the devices.I is shown that the APD is the most sensitive device to temperature,with a current dependence on temperature reaching 6.5%C^(-1)at room temperature,whereas for the other devices this dependence is always<0:6%C^(-1).In terms of long-term stability,the net current of PD can change by up to 4%when working continuously for 8 h and 2%when working intermittently for 32 h,whereas for the other devices,the changes are all<1%.For the dose response,the PMT and SiPM exhibit excellent linear responses and SNRs within the range of 0.1-60 Gy/min For the PSFD with a current readout mode,the performance of the PMT and SiPM is concluded to be better than that of the other devices in the study.In particular,the SiPM,which has a compact size,low bias voltage,and antimagnetic interference,has great advantages for further applications.

Research progress in terahertz quantum-cascade lasers and quantum-well photodetectors

As semiconductor devices,the terahertz quantum-cascade laser is a coherent source based on intersubband transitions of unipolar carriers while the terahertz quantum-well photodetector is a kind of detector which matches the laser frequency.They are solid-state,electrically operated,and can be easily integrated with other components.This paper reviews the state of the art for the design,working performance,and future directions of the two devices.Their applications in photoelectric characterization and imaging are also discussed.

Experimental Investigation of Solar Panel Cooling by a Novel Micro Heat Pipe Array

A novel micro heat pipe array was used in solar panel cooling. Both of air-cooling and water-cooling conditions under nature convection condition were investigated in this paper. Compared with the ordinary solar panel, the maximum difference of the photoelectric conversion efficiency is 2.6%, the temperature reduces maximally by 4.7℃, the output power increases maximally by 8.4% for the solar panel with heat pipe using air-cooling, when the daily radiation value is 26.3 MJ. Compared with the solar panel with heat pipe using air-cooling, the maximum difference of the photoelectric conversion efficiency is 3%, the temperature reduces maximally by 8℃, the output power increases maximally by 13.9% for the solar panel with heat pipe using water-cooling, when the daily radiation value is 21.9 MJ.

An optical glass plane angle measuring system with photoelectric autocollimator

Optical glass is the most widely used optical material.It is necessary to measure its geometric characteristic quickly and reliably to meet the quality of optical glass.A vision measuring system combining photoelectric autocollimation system with high-precision rotary stage is designed to measure the parallelismand angle of optical glass plane.A novel method is proposed to overcome the difficulty ofmeasuring parallelismof optical glass.The model of parallelism and angle measurement is established and the feasibility is analyzed.The image processing algorithm combining Steger algorithm with the least square method is selected.The uncertainty of angle measurement system for angle measurement is 3.0″.The system can solve the problem of measuring the angle of optical glass with high precision and has important significance for optical system.

Preparation and photoelectric properties of cadmium sulfide quantum dots

Cadmium sulfide quantum dots(CdS QDs) are widely used in solar cells, light emitting diodes, photocatalysis, and biological imaging because of their unique optical and electrical properties. However, there are some drawbacks in existing preparation techniques for CdS QDs, such as protection of inert gas, lengthy reaction time, high reaction temperature, poor crystallinity, and non-uniform particle size distribution. In this study, we prepared CdS QDs by liquid phase synthesis under ambient room temperature and atmospheric pressure using sodium alkyl sulfonate, CdCl_2, and Na_2S as capping agent, cadmium, and sulfur sources respectively. This technique offers facile preparation, efficient reaction, low-cost, and controllable particle size. The as-prepared CdS QDs exhibited good crystallinity, excellent monodispersity, and uniform particle size. The responsivity of CdS QDs-based photodetector is greater than 0.3 μA/W, which makes them suitable for use as ultra-violet(UV) detectors.

Multi-area detection sensitivity calculation model and detection blind areas influence analysis of photoelectric detection target

Multi-element array photoelectric detector is the core devices to form a photoelectric detection target with a large field of view.This photoelectric detection target brings about the problem of uneven detection sensitivity distribution in the detection screen.To improve the uneven detection sensitivity of this photoelectric detection target,this paper analyzes the distribution law of the uneven detection sensitivity of the photoelectric detection target using the multi-element array photoelectric detector,dissects the main factors affecting the detection sensitivity according to the photoelectric detection principle,establishes the calculation model of detection sensitivity of the photoelectric detection target in the different detection areas and proposes a method to improve the detection sensitivity by compensating the gain of each unit photoelectric detector.The analysis of simulation and experimental results show that the proposed method of photoelectric detection target can effectively improve the output signal amplitude of the projectile under the certain detection distance,in particular,the output signal amplitude of the projectile is significantly increased when the projectile passes through the detection blind area.The experimental results are consistent with the simulation results,which verify the effectiveness of the proposed improvement method.

Application of BAIRD Photoelectric Spectrometer in Quantitative Analysis of Iron and Steel

ＡｐｐｌｉｃａｔｉｏｎｏｆＢＡＩＲＤＰｈｏｔｏｅｌｅｃｔｒｉｃＳｐｅｃｔｒｏｍｅｔｅｒｉｎＱｕａｎｔｉｔａｔｉｖｅＡｎａｌｙｓｉｓｏｆＩｒｏｎａｎｄＳｔｅｅｌＳｕＺｈｉ①ＡＢＳＴＲＡＣＴＢＡＩＲＤＳＰＥＣＴＲＯＶＡＣ２０００（ＤＶ５）ｃｏｎｓｉｓｔｉ...

Photoelectric properties of thin Eu^(3+)-doped TiO_2 films sensitized by cis-RuL_2(SCN)_2·2H_2O

Thin nanocrystalline TiO2 films doped by europium ions (Eu3+) were obtained by the sol-gel method. The photoelectric properties of Eu3+-doped TiO2 film electrode sensitized by cis-RuL2(SCN)2·2H2O (L=cis-2,2′-bipyridine-4,4′-dicarboxlic acid) ruthenium complex were studied. The thin films were characterized by X-ray diffraction, atomic force microscopy and X-ray photoelectron spectroscopy. Effect of doping Eu3+ on microscopic structure and photoelectrical properties were discussed. The result shows that doping europium ions makes specific surface area of these films larger, which contributes to improving the photoelectric properties. It is found that an optimal composition doped with 0.2 mol.% Eu3+ exhibits the highest photoelectric properties. Isc is 0.37 mA·cm-2, which is 0.17 mA·cm-2 bigger than that of un-doped films; Voc is 405 mV, which is 50 mV bigger than that of un-doped films.

SnS_2 quantum dots: Facile synthesis, properties,and applications in ultraviolet photodetector

Tin sulfide quantum dots(SnS_2 QDs) are n-type wide band gap semiconductor. They exhibit a high optical absorption coefficient and strong photoconductive property in the ultraviolet and visible regions. Therefore, they have been found to have many potential applications, such as gas sensors, resistors, photodetectors, photocatalysts, and solar cells. However, the existing preparation methods for SnS_2 QDs are complicated and require a high temperature and high pressure environments; hence they are unsuitable for large-scale industrial production. An effective method for the preparation of monodispersed SnS_2 QDs at normal temperature and pressure will be discussed in this paper. The method is facile, green,and low-cost. In this work, the structure, morphology, optical, electrical, and photoelectric properties of SnS_2 QDs are studied. The synthesized SnS_2 QDs are homogeneous in size and exhibit good photoelectric performance. A photoelectric detector based on the SnS_2 QDs is fabricated and its J–V and C–V characteristics are also studied. The detector responds under λ = 365 nm light irradiation and reverse bias voltage. Its detectivity approximately stabilizes at 1011 Jones at room temperature. These results show the possible use of SnS_2 QDs in photodetectors.

Technology of signal de-noising and singularity elimination based on wavelet transform

Based on wavelet transform theory,a method for signal de-noising and singularity detection and elimination is proposed,which can reduce the noises and express local singularity.Each singularity can also be detected and located through the local modulus maxima of wavelet transform.Simulation experiments are conducted with MATLAB software.The experimental results demonstrate that the method proposed in this paper is effective and feasible.