Teaching Status and Teaching Reform Ideas of Physical Chemistry Experiments for Food Quality and Safety Major

Physical chemistry experiments are an important branch of chemical experiments.In view of problems and shortcomings in physical chemistry experiment teaching of food quality and safety major in Chengdu University,the teaching methods of physical chemistry experiment course of food quality and safety major were explored and practiced,aiming to arouse students enthusiasm for experiments and cultivate their ability of independent learning,comprehensive thinking and independent problem solving.

Experimental Study on Hydrodynamic Load Characteristics for A Typical Cross-Section of A Submerged Floating Tunnel

The typical cross-sectional form of a submerged floating tunnel plays a significant role in the dynamic response of the tunnel itself,which directly affects the overall design.In this work,a series of experiments involving wave action on a submerged floating tube cross section is reported to study its hydrodynamic load characteristics.Two typical cross section tube cylinders,circular and rectangular,are chosen.Experiments are carried out in a wave flume with waves of relatively low Keulegan-Carpenter(KC)numbers.Three relative depths of submergence of 0,0.25 and 0.5 are chosen.The measured wave forces in regular waves are used to analyze the horizontal force,vertical force and torque,and then the drag coefficient(Cd)and inertia coefficient(Cm)are derived.The results show that the drag coefficients at low KC numbers are large and decrease sharply with increasing KC number.The inertial coefficient Cm values in the vertical direction are about 70%larger than those in the horizontal direction.With an increase in aspect ratio(the ratio of the height to width of the structure),the ratio of inertia coefficient in the horizontal direction to that in the vertical direction increases remarkably.The inertia force coefficient is very sensitive to the submerged water depth and aspect ratio.The existing results may overestimate the actual force value.

The influence of inter-band rock on rib spalling in longwall panel with large mining height

In order to improve rib stability,failure criteria and instability mode of a thick coal seam with inter-band rock layer are analysed in this study.A three-dimensional mechanical model is established for the rib by considering the rock layer.A safety factor is defined foy the rib,and it is observed that the safety factor exhibits a positive correlation with the thickness and strength of the inter-band rock.A calculation method for determining critical parameters of the rock layer is presented to ensure the rib stability.It is revealed that incomplete propagation of the fracture at the hard rock constitutes a fundamental prerequisite for ensuring the rib stability.The influence of the position of the inter-band rock in the coal seam on failure mechanism of the rib was thoroughly investigated by developing a series of physical models for the rib at the face area.The best position for the inter-band rock in the coal seam is at a height of 1.5 m away from the roof line,which tends to provide a good stability state for the rib.For different inter-band rock positions,two ways of controlling rib by increasing supports stiffness and flexible grouting reinforcement are proposed.

Sliding and damming properties of granular debris with different geometric configurations and grain size distributions

Granular debris plays a significant role in determining damming deposit characteristics. An indepth understanding of how variations in grain size distribution(GSD) and geometric configurations impact the behavior of granular debris during the occurrence of granular debris is essential for precise assessment and effective mitigation of landslide hazards in mountainous terrains. This research aims to investigate the impact of GSD and geometric configurations on sliding and damming properties through laboratory experiments. The geometric configurations were categorized into three categories based on the spatial distribution of maximum volume: located at the front(Type Ⅰ), middle(Type Ⅱ), and rear(Type Ⅲ) of the granular debris. Our experimental findings highlight that the sliding and damming processes primarily depend on the interaction among the geometric configuration, grain size, and GSD in granular debris. Different sliding and damming mechanisms across various geometric configurations induce variability in motion parameters and deposition patterns. For Type Ⅰ configurations, the front debris functions as the critical and primary driving component, with energy dissipation primarily occurring through inter-grain interactions. In contrast, Type Ⅱ configurations feature the middle debris as the dominant driving component, experiencing hindrance from the front debris and propulsion from the rear, leading to complex alterations in sliding motion. Here, energy dissipation arises from a combination of inter-grain and grain-substrate interactions. Lastly, in Type Ⅲ configurations, both the middle and rear debris serve as the main driving components, with the rear sliding debris impeded by the front. In this case, energy dissipation predominantly results from grainsubstrate interaction. Moreover, we have quantitatively demonstrated that the inverse grading in damming deposits, where coarse grain moves upward and fine grain moves downward, is primarily caused by grain sorting due to collisions among the grains and between the grain and the base. The impact of grain on the horizontal channel further aids grain sorting and contributes to inverse grading. The proposed classification of three geometric configurations in our study enhances the understanding of damming properties from the view of mechanism, which provides valuable insights for related study about damming granular debris.

Permeability Estimation of Shale Oil Reservoir with Laboratory-derived Data: A Case Study of the Chang 7 Member in Ordos Basin

The shale oil reservoir within the Yanchang Formations of Ordos Basin harbors substantial oil and gas resources and has recently emerged as the primary focus of unconventional oil and gas exploration and development.Due to its complex pore and throat structure,pronounced heterogeneity,and tight reservoir characteristics,the techniques for conventional oil and gas exploration and production face challenges in comprehensive implementation,also indicating that as a vital parameter for evaluating the physical properties of a reservoir,permeability cannot be effectively estimated.This study selects 21 tight sandstone samples from the Q area within the shale oil formations of Ordos Basin.We systematically conduct the experiments to measure porosity,permeability,ultrasonic wave velocities,and resistivity at varying confining pressures.Results reveal that these measurements exhibit nonlinear changes in response to effective pressure.By using these experimental data and effective medium model,empirical relationships between P-and S-wave velocities,permeability and resistivity and effective pressure are established at logging and seismic scales.Furthermore,relationships between P-wave impedance and permeability,and resistivity and permeability are determined.A comparison between the predicted permeability and logging data demonstrates that the impedance–permeability relationship yields better results in contrast to those of resistivity–permeability relationship.These relationships are further applied to the seismic interpretation of shale oil reservoir in the target layer,enabling the permeability profile predictions based on inverse P-wave impedance.The predicted results are evaluated with actual production data,revealing a better agreement between predicted results and logging data and productivity.

Formation mechanism of fault accommodation zones under combined stress in graben basin:Implications from geomechanical modeling

A fault accommodation zone is a type of structure that is defined as regulating displacement and strain between faults structure.Increasing numbers of fault accommodation zones are being identified in graben basins,indicating the potential exploration target and petroleum accumulation areas.This study aims to analyze the formation mechanism and development of fault accommodation zones under combined stress by a numerical simulation method considering geomechanical modeling.Using three-dimensional(3-D)seismic interpretation and fractal dimension method,exampled with the Dongxin fault zone,the fault activity and fault combination pattern were conducted to quantitatively characterize the activity difference in fault accommodation zones.Combined with mechanical experiment test,a geomehcanical model was established for fault accommodation zones in a graben basin.Integrating the paleostress numerical simulations and structural physical simulation experiment,the developmental characteristics and genetic mechanism of fault accommodation zones were summarized.Influenced by multi movements and combined stresses,three significant tectonic evolution stages of the Dongxing Fault Zone(DXFZ)were distinguished:During the E_(s)^(3)sedimentary period,the large difference in the stress,strain,and rupture distribution in various faults were significant,and this stage was the key generation period for the prototype of the DXFZ,including the FAZ between large-scale faults.During the E_(s)^(2)sedimentary period,the EW-trending symmetric with opposite dipping normal faults and the NE-SW trending faults with large scale were furtherly developed.The junction area of two secondary normal faults were prone to be ruptured,performing significant period for inheriting and developing characteristics of fault accommodation zones.During the Es1 sedimentary period,the high-order faults in the DXFZ exhibited the obvious fault depressions and strike-slip activity,and the fault accommodation zones were furtherly inherited and developed.This stage was the molded and formative period of the FAZ,the low-order faults,and the depression in the DXFZ.

Maximum initial primary wave model for low-Froude-number reservoir landslides based on wave theory

The impulse waves induced by large-reservoir landslides can be characterized by a low Froude number.However,systematic research on predictive models specifically targeting the initial primary wave is lacking.Taking the Shuipingzi 1#landslide that occurred in the Baihetan Reservoir area of the Jinsha River in China as an engineering example,this study established a large-scale physical model(with dimensions of 30 m×29 m×3.5 m at a scale of 1:150)and conducted scaled experiments on 3D landslide-induced impulse waves.During the process in which a sliding mass displaced and compressed a body of water to generate waves,the maximum initial wave amplitude was found to be positively correlated with the sliding velocity and the volume of the landslide.With the increase in the water depth,the wave amplitude initially increased and then decreased.The duration of pressure exertion by the sliding mass at its maximum velocity directly correlated with an elevated wave amplitude.Based on the theories of low-amplitude waves and energy conservation,while considering the energy conversion efficiency,a predictive model for the initial wave amplitude was derived.This model could fit and validate the functions of wavelength and wave velocity.The accuracy of the initial wave amplitude was verified using physical experiment data,with a prediction accuracy for the maximum initial wave amplitude reaching 90%.The conversion efficiency(η)directly determined the accuracy of the estimation formula.Under clear conditions for landslide-induced impulse wave generation,estimating the value ofηthrough analogy cases was feasible.This study has derived the landslide-induced impulse waves amplitude prediction formula from the standpoints of wave theory and energy conservation,with greater consideration given to the intrinsic characteristics in the formation process of landslide-induced impulse waves,thereby enhancing the applicability and extensibility of the formula.This can facilitate the development of empirical estimation methods for landslide-induced impulse waves toward universality.

Calculating the number of radial cracks around a wellbore fractured by liquid CO2 phase transition blasting technology

Integrating liquid CO_(2)phase transition blasting(LCPTB)technology with hydraulic fracturing(HF)methods can help reduce wellbore damage,create multiple radial fractures,and establish a complex fracture network.This approach significantly increases the recovery efficiency of low-permeability oil and gas fields.Accurately calculating the number of fractures caused by LCPTB is necessary to predict production enhancement effects and optimize subsequent HF designs.However,few studies are reported on large-scale physical model experiments in terms of a method for calculating the fracture number.This study analyzed the initiation and propagation of cracks under LCPTB,derived a calculation formula for crack propagation radius under stress waves,and then proposed a new,fast,and accurate method for calculating the fracture number using the principle of mass conservation.Through ten rock-breaking tests using LCPTB,the study confirmed the effectiveness of the proposed calculation approach and elucidated the variation rule of explosion pressure,rock-breaking scenario,and the impact of varying parameters on fracture number.The results show that the new calculation method is suitable for fracturing technologies with high pressure rates.Recommendations include enlarging the diameter of the fracturing tube and increasing the liquid CO2 mass in the tube to enhance fracture effectiveness.Moreover,the method can be applied to other fracturing technologies,such as explosive fracturing(EF)within HF formations,indicating its broader applicability and potential impact on optimizing unconventional resource extraction technologies.

Experiments on Channel Evolution due to Dam Removal in Taiwan

Due to safety concerns and habitat restoration for landlocked salmon,a 13-m high check dam on Chijiawan Creek was removed in late May 2011 in Taiwan.We conducted experiments to understand channel evolution of different scenarios.We further compared our experimental results of riverbed elevation changes with the analytical solutions derived from the diffusion equation and field dynamics as well after the creek experienced the first flood event.The results indicated that magnitude of discharges and notch size are dominant factors in resulting channel evolution.While the largest differences between grain size distribution are associated with discharge,the largest differences in net change in upstream volume are associated with notch size.While the theoretical equation could help understand the channel change after dam removal,it only explained the evolution closer to the dam.The physical experiments,on the other hand,provided insights especially with regard to comparing alternative proposed management actions.The discrepancies between predicted and actual outcome highlight more needed inputs for future dam-removal assessments.

Reform and Practice of University Physics Experimental Teaching Based on OBE Concept

Aiming at the problems of unclear teaching objectives,obsolete content,and single method in the experimental teaching of university physics at our university,we have implemented a series of reform initiatives.It mainly includes clarifying the student-centered teaching objectives,optimizing the experimental content,innovating the teaching methods,improving the assessment and evaluation system,and improving the experimental conditions[1,2].After the implementation of the reform,the learning effectiveness of students has been significantly improved,the teaching level of teachers has been significantly enhanced,the curriculum system has been optimized,the efficiency of teaching management has been enhanced,and social recognition has been strengthened.Practice shows that the teaching reform based on the outcome-based education concept effectively improves the quality of university physics experimental teaching and lays the foundation for cultivating innovative talents.

Three-Dimensional Finite Element Numerical Simulation and Physical Experiment for Magnetism-Stress Detecting in Oil Casing

The casing damage has been a big problem in oilfield production. The current detection methods mostly are used after casing damage, which is not very effective. With the rapid development of China's offshore oil industry, the number of offshore oil wells is becoming larger and larger. Because the cost of offshore oil well is very high, the casing damage will cause huge economic losses. What's more, it can also bring serious pollution to marine environment. So the effective methods of detecting casing damage are required badly. The accumulation of stress is the main reason for the casing damage. Magnetic anisotropy technique based on counter magnetostriction effect can detect the stress of casing in real time and help us to find out the hidden dangers in time. It is essential for us to prevent the casing damage from occurring. However, such technique is still in the development stage. Previous studies mostly got the relationship between stress and magnetic signals by physical experiment, and the study of physical mechanism in relative magnetic permeability connecting the stress and magnetic signals is rarely reported. The present paper uses the ANSYS to do the three-dimensional finite element numerical simulation to study how the relative magnetic permeability works for the oil casing model. We find that the quantitative relationship between the stress' s variation and magnetic induction intensity's variation is: Δδ =K* ΔB, K = 8.04×109, which is proved correct by physical experiment.

Numerical simulation of non-Archie electrophysical property of saturated rock with lattice Boltzmann method

The electrophysical property of saturated rocks is very important for reservoir identification and evaluation. In this paper, the lattice Boltzmann method （LBM） was used to study the electrophysical property of rock saturated with fluid because of its advantages over conventional numerical approaches in handling complex pore geometry and boundary conditions. The digital core model was constructed through the accumulation of matrix grains based on their radius distribution obtained by the measurements of core samples. The flow of electrical current through the core model saturated with oil and water was simulated on the mesoscopic scale to reveal the non-Archie relationship between resistivity index and water saturation （I-Sw）. The results from LBM simulation and laboratory measurements demonstrated that the I-Sw relation in the range of low water saturation was generally not a straight line in the log-log coordinates as described by the Archie equation. We thus developed a new equation based on numerical simulation and physical experiments. This new equation was used to fit the data from laboratory core measurements and previously published data. Determination of fluid saturation and reservoir evaluation could be significantly improved by using the new equation.

Western fault zone of South China Sea and its physical simulation evidences

The western fault zone of the South China Sea is a strike-slip fault system and consists of four typical strike-slip faults. It is the western border of the South China Sea. The formation of the system is due to the extrusion of Indo - China Peninsula caused by the collision of India with Tibet and the spreading of the South China Sea in Cenozoic. There are five episodes of tectonic movement along this fault zone, which plays an important role in the Cenozoic evolution of the South China Sea. By the physical modeling experiments, it can be seen the strike-slip fault undergoes the sinistral and dextral movement due to the relative movement velocity change between the South China Sea block and the Indo - China block. The fault zone controls the evolution of the pull basins locating in the west of the South China Sea.

Overlying strata movement of recovering standing pillars with solid backfilling by physical simulation

To analyze the overlying strata movement law of recovering room mining standing pillars with solid backfilling.Physical simulation experiments with sponge and wood as the backfilling simulation material were tested.The results show that:(i) The covering-rock mechanics of the overly strata comes from "two-arch structures + hinged girder + bend beam" to "backfilling material + hinged girder + bent beam" by increasing the fill ratio from 0%to 85%,the beginning of overlying strata movement appears later and the total duration of subsidence velocity increased from zero to the highest value increases.The trend of "single polarization" of the subsidence velocity curves becomes noticeable and the velocity variation trend becomes stable,(ii) The equiponderate aeolian sand was added to improve the anti-pressure ability of the loess,and the corresponding ground processing & transportation system was designed.

Designing physical experiment about characters of fuel cells

Currently, proton exchange membrane fuel cells are the most widely used fuel cell technology, In this article the function of fuel cells is briefly introduced. Certain characters of fuel cells are investigated through measuring the relation between electric current, voltage and product. A series of physics experiments using fuel cells is designed.

Tight sandstone gas accumulation mechanisms and sweet spot prediction, Triassic Xujiahe Formation, Sichuan Basin, China

The prediction of continental tight sandstone gas sweet spots is an obstacle during tight sandstone gas exploration. In this work, the classic physical fluid charging experimental equipment is improved, the combination of the gas migration and accumulation process with the pore network numerical simulation method is investigated, and application of the permeability/porosity ratio is proposed to predict the gas saturation and sweet spots of continental formations. The results show that (1) as the charging pressure increases, the permeability of the reservoir increases because more narrow pore throats are displaced in the percolation process;and (2) based on pore network numerical simulation and theoretical analysis, the natural gas migration and accumulation mechanisms are revealed. The gas saturation of tight sandstone rock is controlled by the gas charging pressure and dynamic percolation characteristics. (3) The ratio of permeability/porosity and fluid charging pressure is proposed to predict the gas saturation of the formation. The ratio is verified in a pilot and proven to be applicable and practical. This work highlights the tight sandstone gas migration and accumulation mechanisms and narrows the gap among microscale physical experiments, numerical simulation research, and field applications.

Real-time localization for underwater equipment using an extremely low frequency electric field

A new real-time underwater equipment location method adopting an electric field induced by a standard current source is proposed.Our goals were real-time tracking and location of stationary or moving underwater equipment both in shallow and deep seas,under noisy conditions.The main features of this method are as follows:(1)a standard current source on the water surface,which can be towed by a vehicle,consisting of two electrodes,a signal generator,and a GPS unit;(2)measurement of the extremely low frequency(ELF)electric field emitted by the current source,made possible by electric field sensors on the underwater equipment;(3)position of the underwater equipment is estimated in real time based on a progressive update extended Kalman filter(PUEKF),which is carried out using the propagation model of an ELF electric field because the electric field at the position of the underwater equipment and the current source position are known.We verified the accuracy of our method and confirmed real-time location feasibility through numerical,physical scale,and real-time sea experiments.Through numerical experiments,we verified that our method works for underwater equipment location in real-world conditions,and the location error can be less than 0.2 m.Next,real-time location experiments for stationary underwater measuring equipment in water tank were conducted.The result shows that the location error can be less than 0.1 m.We also confirmed real-time location feasibility through the use of offshore experiment.We expect that our method will complement conventional underwater acoustic location methods for underwater equipment in acoustically noisy environments.

Experimental observation on water entry of a sphere in regular wave

This paper presents a novel experiment to observe the whole water entry process of a free-falling sphere into a regular wave.A time-accurate synchronizing system modulates the moment elaborately to ensure the sphere impacting onto the water surface at the desirable wave phase.Four high-speed cameras focus locally to measure the high-precision size of the cavity evolution.Meanwhile,the aggregated field view of the camera array covers both the splash above the free surface and the entire cavity in the wave.The detailed methodologies are described and verified for the hardware set-up and the image post-processing.The theoretical maximum deviation is 1.7%on the space scale.The integral morphology of the cavity is captured precisely in the coordinate system during the sphere penetrates through the water at four representative wave phases and the still water.The result shows that the horizontal velocity of the fluid particle in the wave impels the cavity and changes the shape distinctly.Notably,the wave motion causes the cavity to pinch offearlier at the wave trough phase and later at the wave crest phase than in the still water.The wave motion influences the falling process of the sphere slightly in the present parameters.

Hydrodynamic Performance and Power Absorption of A Coaxial DoubleBuoy Wave Energy Converter

As an important wave energy converter(WEC),the double-buoy device has advantages of wider energy absorption band and deeper water adaptability,which attract an increasing number of attentions from researchers.This paper makes an in-depth study on double-buoy WEC,by means of the combination of model experiment and numerical simulation.The Response Amplitude Operator(RAO)and energy capture of the double-buoy under constant power take-off(PTO)damping are investigated in the model test,while the average power output and capture width ratio(CWR)are calculated by the numerical simulation to analyze the influence of the wave condition,PTO,and the geometry parameters of the device.The AQWA-Fortran united simulation sy stem,including the secondary developme nt of AQWA software coupled with the flowchart of the Fortran code,models a new dynamic system.Various viscous damping and hydraulic friction from WEC system are measured from the experimental results,and these values are added to the equation of motion.As a result,the energy loss is contained in the final numerical model the by united simulation system.Using the developed numerical model,the optimal period of energy capture is identified.The power capture reaches the maximum value under the outer buoy's natural period.The paper gives the peak value of the energy capture under the linear PTO damping force,and calculates the optimal mass ratio of the device.

Research on the mechanical properties of the reinforced materials of retaining wall

The main research purpose of this paper is to study the mechanical properties of the sand gravel packing of the retaining wall under the creep condition of reinforced materials, in order to figure it out, Indoor physical experiments were carried out.