IMPROVEMENT OF MECHANICAL PROPERTIES OF MARTENSITIC STAINLESS STEEL BY PLASMA NITRIDING AT LOW TEMPERATURE

A series of experiments were carried out to study the influence of low temperature plasma nitriding on the mechanical properties of AISI 420 martensitic stainless steel. Plasma nitriding experiments were carried out for 15 h at 350℃ by means of DC- pulsed plasma in 25%N2＋ 75%H2 atmosphere. The microstructure, phase composition, and residual stresses profiles of the nitrided layers were determined by optical microscopy and X-ray diffraction. The microhardness profiles of the nitridied surfaces were also studied. The fatigue life, sliding wear, and erosion wear loss of the untreated specimens and plasma nitriding specimens were determined on the basis of a rotating bending fatigue tester, a ball-on-disc wear tester, and a solid particle erosion tester. The results show that the 350℃ nitrided surface is dominated by c-Fe3N and ON, which is supersaturated nitrogen solid solution. They have high hardness and chemical stabilities. So the low temperature plasma nitriding not only increases the surface hardness values but also improves the wear and erosion resistance. In addition, the fatigue limit of AISI 420 steel can also be improved by plasma nitriding at 350℃ because plasma nitriding produces residual compressive stress inside the modified layer.

Recent advances in non-thermal plasma(NTP)catalysis towards C1 chemistry

C1 chemistrymainly involves the catalytic transformation of C1molecules(i.e.,CO,CO2,CH4 and CH3OH),which usually encounters thermodynamic and/or kinetic limitations.To address these limitations,non-thermal plasma(NTP)activated heterogeneous catalysis offers a number of advantages,such as relatively mild reaction conditions and energy efficiency,in comparison to the conventional thermal catalysis.This review presents the state-of-the-art for the application of NTP-catalysis towards C1 chemistry,including the CO2 hydrogenation,reforming of CH4 and CH3OH,and water-gas shift(WGS)reaction.In the hybrid NTP-catalyst system,the plasma-catalyst interactions aremultifaceted.Accordingly,this reviewalso includes a brief discussion on the fundamental research into themechanisms of NTP activated catalytic C1 chemistry,such as the advanced characterisation methods(e.g.,in situ diffuse reflectance infrared Fourier transform spectroscopy,DRIFTS),temperatureprogrammed plasma surface reaction(TPPSR),kinetic studies.Finally,prospects for the future research on the development of tailor-made catalysts for NTP-catalysis systems(which will enable the further understanding of its mechanism)and the translation of the hybrid technique to practical applications of catalytic C1 chemistry are discussed.

Experimental Research of Inactivation Effect of Low-Temperature Plasma on Bacteria

The killing logarithms index in killing a vegetative form in an explosure of about 90s and a spore in an explosure of about 120s, by using a low-temperature plasma produced by dielectric barrier discharge （DBD）, reached 5. The speed in killing the strains tested, by using a low-temperature plasma, was the highest with E. Coli, then S. Aureus and B. Subtilis var niger spore. The results of the scanning electron microscope showed that the low-temperature plasma destroyed the outer structure of the bacteria and that the vegetative form was more susceptible to the inactivation effect of the low-temperature plasma than was the spore. This indicated that the effects of the high voltage and high velocity particle flow, in plasma, penetrating through the outer structure of the bacteria might play a dominant role during the inactivation of the bacteria.

Applications and challenges of low temperature plasma in pharmaceutical field

Low temperature plasma(LTP)technology has shown an outstanding application value in the pharmaceutical filed in recent ten years.This paper reviews the research advances in LTP,including its effects on enhancing or inhibiting drug activity,its combined use with drugs to treat cancers,its effects on the improvement of drug delivery system,its use in preparation of new inactivated virus vaccines,its use with mass spectrometry for rapid detection of drug quality,and the anti-tumor and sterilization effects of plasma-activated liquids.The paper also analyzes the challenges of LTP in the pharmaceutical filed,hoping to promote related research.

Surface Modification of Polyvinylidene Fluoride (PVDF) Membranes by Low-Temperature Plasma with Grafting Styrene

In order to control the surface pore sizes of polyvinylidene fluoride membranes and their distribution, low temperature plasma-induced grafting modifications of PVDF were studied to prepare hydrophobe membranes. By argon （Ar） treating and subsequent grafting reaction, a hydrophobe monomer, styrene, was introduced into the PVDF membrane. Fourier transform infrared attenuated total reflection （FTIR-ATR） was utilized to characterize the chemical and physical changes in the Ar plasma modified membrane. The surface modifications of PVDF membranes were investigated by using scanning electron microscopy （SEM）, atomic force microscopy （AFM） and differential scanning calorimeter （DSC）. The water permeability and the solute rejection were measured by PVDF membrane modified in different graft conditions. Results demonstrated that the pores in the modified membranes get smaller and the distribution of pores gets narrowed with the increase in grafting reaction duration. Longer graft time caused the water flux of PVDF membrane to decrease from 578 kg/（m^2· h） to 23 kg/（m^2· h） and the solute rejection to increase from 73% to 92%.

Low-Temperature Plasma Induced Grafting of 2-Methacryloyloxyethyl Phosphorylcholine onto Poly(tetrafluoroethylene) Films

Modification of poly(tetrafluoroethylene)(PTFE) films with 2-methacryloyloxyethyl phosphorylcholine(MPC) was performed by low-temperature plasma treatment and grafting polymerization.Surface properties of PTFE were characterized by attenuated total reflectance Fourier transform infrared(ATR-FTIR) spectra,X-ray photoelectron spectroscopy(XPS) ,and static contact angle.The results show that MPC has been grafted onto PTFE film surface successfully.Contact angle for the modified PTFE films in the water decreased from 108°to 58.25°,while surface energy increased from 17.52 mN/m to 45.47 mN/m.The effects of plasma treatment time,monomer concentration and grafting time on degree of grafting were determined.In the meanwhile,blood compatibility of the PTFE films was studied by checking thrombogenic time of blood plasma.

Low-temperature Plasma Promotes Fibroblast Proliferation in Wound Healing by ROS-activated NF-κB Signaling Pathway

Low-temperature plasma（LTP） has shown great promise in wound healing,although the underlying mechanism remains poorly understood.In the present study,an argon atmospheric pressure plasma jet was employed to treat L929 murine fibroblasts cultured in vitro and skin wounds in BALB/c mice.The in vitro analysis revealed that treatment of fibroblasts with LTP for 15 s resulted in a significant increase in cell proliferation,secretion of epidermal growth factor（EGF） and transforming growth factor-β1（TGF-β1）,production of intracellular reactive oxygen species（ROS）,and the percentage of cells in S phase,protein expression of phosphorylated p65（P-p65） and cyclin D1,but a noted decrease in the protein expression of inhibitor kappa B（IκB）.The in vivo experiments demonstrated that 30-s LTP treatment enhanced the number of fibroblasts and the ability of collagen synthesis,while 50-s treatment led to the opposite outcomes.These results suggested that LTP treatment promotes the fibroblast proliferation in wound healing by inducing the generation of ROS,upregulating the expression of P-p65,downregulating the expression of IκB,and activating the NF-κB signaling pathway and consequently altering cell cycle progression（increased DNA synthesis in S phage）.

Dyeing Behavior of Yak Hair Fiber Treated with Microwave Low Temperature Plasma

The scales on the surface of yak hair fiber act as barriers during the dyeing process. In order to solve the scale problem and to improve the dyeability of yak hair, yak hair fiber was treated by microwave low temperature plasma (MLTP) in this study. The weight loss and the dyeing properties of the yak hair fiber modified by MLTP were investigated. Scanning Electron Microscopy (SEM) photographs were taken to observe the changes in the surface shape of yak hair fiber before and after treatment. Results showed that after MLTP treatment, the scale structure of yak hair was weakened and damaged greatly and the noticeable changes on the surface shape took place. At the same time, a significant improvement in dyeing properties of yak hair fiber was exhibited.

Surface XPS-investigations of tobacco leaves treated with low-temperature plasma

The tobacco leaves were treated with low-temperature plasma in Ar, N2, O2, and air atmospheres at different powers (60―130 W). The surface-elemental components, their relative contents, and the functional groups of the surface components of the tobacco leaves were determined using XPS (X-ray photoelectron spectroscopy). The ex- perimental results showed that the percentage of the elements C, N, and O had changed considerably and a large number of polar functional groups containing oxygen atoms were incorporated into the components on the tobacco surfaces. The measurements of the surface contact angle showed that the surface contact angle of the modified tobacco leaves was 0 degree, whereas it was 110 degrees before the plasma treatment. These results indicate that the wettability of the modified tobacco leaves improved dramatically. This work may be significant for future researches on the surface modification of the tobacco leaves.

Destruction of Gaseous Styrene with a Low-Temperature Plasma Induced by a Tubular Multilayer Dielectric Barrier Discharge

The destruction of gaseous styrene was studied using a low-temperature plasma induced by tubular multilayer dielectric barrier discharge（DBD）.The results indicate that the applied voltage,gas flow rate,inlet styrene concentration and reactor configuration play important roles in styrene removal efficiency （ηstyrene） and energy yield（EY）.Values of ηstyrene and EY reached 96%and 15567 mg/kWh when the applied voltage,gas flow rate,inlet styrene concentration and layers of quartz tubes were set at 10.8 kV,5.0 m/s,229 mg/m^3 and 5 layers,respectively.A qualitative analysis of the byproducts and a detailed discussion of the reaction mechanism are also presented.The results could facilitate industrial applications of the new DBD reactor for waste gas treatment.

Study on Free Surface and Channel Flow Induced by Low Temperature Plasma via Lattice Boltzmann Method

Active boundary layer flow control and boundary layer manipulation in the channel flow that was based on low temperature plasma were studied by means of a lattice Boltzmann method. Two plasma actuators were placed in a row to obtain the influence rule of their separation distance on the velocity profile at three locations and maximum velocity in the flow field. Two plasma actuators were placed symmetrically inside a channel to examine the effect of channel height and voltage on the velocity profile and flow rate. It was found that the channel height controls the distribution of flow velocity, which affected the flow rate and its direction. Increasing plasma voltage had a negative effect on the flow rate due to the generation of a larger and stronger flow vortex.

BEHAVIOR OF CHO CELLS ON MODIFIED POLYPROPYLENE BY LOW TEMPERATURE AMMONIA PLASMA

The surface of polypropylene (PP) membrane was modified by low temperature plasma with ammonia. The effect of exposure time was investigated by means of contact angle measurement. The results show that low temperature ammonia plasma treatment can enhance its hydrophilicity. Chinese hamster ovary (CHO) cells attachment on the modified membrane was enhanced and the growth rate on the membrane was faster than unmodified one.

Remove of Phenolic Compounds in Water by Low-Temperature Plasma: A Review of Current Research

Phenolic compounds have very strong toxicity, so it has been paid sharply attention to find an effective way of controlling the wastewater containing phenolic compounds. The work on this subject done by domestic and overseas scholars is studied in this paper, and the progress of researches on low-temperature plasma treatment is summarized through the electrical discharge types, mechanism, kinetics of phenolic compounds decomposition and combination of several methods with low-temperature plasma treatment. In addition, the crucial problem and the developing tendency on low-temperature plasma treatment for phenol-bearing wastewater are briefly discussed.

Effect of processing temperatures on characteristics of surface layers of low temperature plasma nitrocarburized AISI 204Cu austenitic stainless steel

The influence of processing temperatures on the surface characteristics of AISI 204Cu austenitic stainless steel was investigated during a low temperature plasma nitrocarburizing.The resultant layer was a dual-layer structure,which comprises a N-enriched layer on the top of C-enriched layer.The surface hardness and the layer thickness increase up to about HV 0.05 1000 and 20μm with increasing temperature.The specimen treated at 400°C shows a much enhanced corrosion resistance compared to the untreated steel.A loss in corrosion resistance was observed for specimens treated at temperatures above 430°C due to the formation of Cr2N.

AN FTIR SPECTROSCOPIC STUDY OF LOW TEMPERATURE PLASMA TREATED WOOL FABRIC

FTIR-ATR technique with second-order derivative measurement was used for assessing the amount of oxidation products of cystine present on the plasma-treated wool fabric surface. In this paper, three non-polymerising gases namely oxygen, nitrogen and 25% hydrogen/75% nitrogen gas mixture were used for the plasma treatment of wool fabric. The oxidation products of cystine studied included S-sulphonate, cysteic acid, cystine monoxide and cystine dioxide. The variations of the amount of these products as a function of treatment time were studied. Experimental results showed that the oxygen plasma could produce a large amount of oxidation products of cystine on the wool fabric surface followed by nitrogen plasma and gas mixture plasma.

Improvement of Linen Fabric Wickability by Low Temperature Plasma Treatment

Low temperature plasma treatments were applied to linen with oxygen and argon, various level of discharge power and exposure time. Tbe fabric weight loss increased with the exposure time. Their effects on surface chemical properties and morphology of flax fiber, and fabric wickability were investigated. X - ray photoelec-tron spectroscopy discovered that the surface oxygen content of the plasma treated sample was increased. Formation of voids and cracks on the fiber surface was revealed by the scanning electron microscopy. Fabric wickability first was increased and then decreased with the prolonged exposure.

Oxidation Degradation of Aqueous Carbofuran Induced by Low Temperature Plasma

The oxidative degradation of aqueous carbofuran, a heavily used toxic carbamate insecticide by low temperature plasma, was investigated. The results show that the treatment efficiency increases with the increase in initial concentration. Raising the treatment temperature and changing the pH value can result in enhanced degradation of carbofuran in solution. The results also show that low temperature plasma treatment can effectively remove chemical oxygen demand （COD） of carbofuran in the solution.

Effects of Low Temperature Plasma on the Forms of Heavy Metals in Sludge

Low temperature plasma was used to treat sludge,and the effects of discharge time on the content of different forms of heavy metals in the sludge were studied. The results showed that Cu and Zn content in the domestic sludge could basically meet the requirements of GB 4284-2018,GB/T 23486-2009,CJ/T 362-2011 and CJ/T 309-2009. There were big differences between different forms of the heavy metals. According to the proportions of different forms of Cu in the sludge,different forms of Cu are arranged as follows: organic state > carbonate bound state> residual state > exchangeable state > iron-manganese oxidation state,and Cu mainly existed in an organic state. Various forms of Zn are arranged in order of the proportion as follows: iron-manganese oxidation state > residual state > carbonate bound state > exchangeable state > organic state,and Zn mainly existed in an iron-manganese oxidation state. After the treatment of sludge by low temperature plasma,the content of exchangeable Cu and Zn in the sludge increased,while the content and proportion of residual Cu and Zn all reduced.

A STUDY ON THE STRUCTURE AND PROPERTIES OF POLYBUTYLALDEHYDE FORMED IN LOW TEMPERATURE PLASMA

The polybutylaldehyde obtained by plasma polymerization was investigated by means of IR, X-ray diffraction, GC-MS, elementary analysis, TEM, electron diffraction and contact angle measurements etc. The results showed that the polymer formed in plasma is amorphous crosslinked polymer, and its backbone is made of carbon atoms. The surface energy of the polymer film is independent of the polymerization conditions. No addition reaction has taken place in the carbonyl group of butylaldehyde in the plasma condition. The result of the wettability measurements showed that the polymer film is generally hydrophobic and the surface energy of the film is about 41 dyn/cm, in which the dispersion force contribution is the majority. The electron diffraction proved that some crystal substance, even the single crystals were present in the polymer. X-ray diffraction also proved the presence of crystal and showed about 15% crystaUinity fraction.

Design and characteristics investigation of a miniature low-temperature plasma spark discharge device

Atmospheric pressure low-temperature plasma is a promising tool in biomedicine applications including blood coagulation,bacterial inactivation,sterilization,and cancer treatment,due to its high chemical activity and limited thermal damage.It is of great importance to develop portable plasma sources that are safe to human touch and suitable for outdoor and household operation.In this work,a portable and rechargeable low-temperature plasma spark discharge device(130 mm×80 mm×35 mm,300 g)was designed.The discharge frequency and plume length were optimized by the selection of resistance,capacitance,electrode gap,and ground electrode aperture.Results show that the spark plasma plume is generated with a length of 12 mm and a frequency of 10 Hz at a capacitance of 0.33μF.resistance of 1 MΩ,electrode gap of 2 mm,and ground electrode aperture of 1.5 mm.Biological tests indicate that the plasma produced by this device contains abundant reactive species,which can be applied in plasma biomedicine,including daily sterilization and wound healing.