Microstructure and corrosion resistance of Fe/Mo composite amorphous coatings prepared by air plasma spraying

Fe/Mo composite coatings were prepared by air plasma spraying （APS） using Fe-based and Mo-based amorphous and nanocrys- talline mixed powders. Microstructural studies show that the composite coatings present a layered structure with low porosity due to adding the self-bonded Mo-based alloy. Corrosion behaviors of the composite coatings, the Fe-based coatings and the Mo-based coatings were in- vestigated by electrochemical measurements and salt spray tests. Electrochemical results show that the composite coatings exhibit a lower polarization current density and higher corrosion potentials than the Fe-based coating when tested in 3.5wt% NaC1 solutions, indicating supe- rior corrosion resistance compared with the Fe-based coating. Also with the increase in addition of the Mo-based alloy, a raised corrosion re- sistance, inferred by an increase in corrosion potential and a decrease in polarization current density, can be found. The results of salt spray tests again show that the corrosion resistance is enhanced by adding the Mo-based alloy, which helps to reduce the porosity of the composite coatings and enhance the stability of the passive films.

Effect of Thermal Treatment on the Grain Growth of Nanostructured YSZ Thermal Barrier Coating Prepared by Air Plasma Spraying

A nanostructured thermal barrier coating is prepared by air plasma spraying using the 8wt% Y_2O_3 partially stabilized zirconia nano-powder with an average grain size of 40 nm. The microstructure and phase composition of feedstock nano-powder and coating are investigated using SEM, TEM and XRD. It is found that the as-sprayed zirconia coating has an average grain size of 67 nm and mainly consistes of metastable tetragonal phase, together with some monoclinic phase and tetragonal phase. Thermal treatment results show that the grains of the nanostructured coating grow slightly below 900℃, whereas over 1000℃ the gains grow rapidly and monoclinic phase noticeably appeares.

Preparation of Ni60-WC Coating by Plasma Spraying, Plasma Re-melting and Plasma Spray Welding on Surface of Hot Forging Die

In order to produce the hear-resistant inner layer of hot-forging die, the plasma spraying and plasma re-melting and plasma spray welding were adopted. Substrate material was W6Mo5Cr4V2, including 10%, 20%, 30% tungsten carbide （WC） ceramic powder used as coating material to obtain different Nickel-based WC alloys coating. Micro-structure and micro-hardness analysis of the coating layer are conducted, as well as thermophysical properties for the coating layer were measured. The experimental results show that the coating prepared with 70%Ni60, 30%WC powder has the best properties with plasma spray welding, in which the micro-hardness can achieve 900HV, meanwhile it can improve the thermal property of hot-forging die dramatically.

Preparation and characterization of nanostructured Al_2O_3-13wt.%TiO_2 ceramic coatings by plasma spraying

Nanostructured and conventional Al2O3-13wt.%TiO2 ceramic coatings were prepared by plasma spraying with nanostructured agglomerated and conventional powders, respectively. The microstructure and microhardness of the coatings were investigated using scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and microhardness measurement. Meanwhile, the friction and wear behaviors were analyzed and compared using a ball-on-disk tribometer. The results show that the conventional coating has lamellar stacking characteristic and has some pores. However, the nanostructured coating shows a bimodal microstructure, which is composed of both fully melted regions and partially melted regions. According to the microstructural difference, the partially melted regions can be divided into liquid-phase sintered regions （a three-dimensional net or skeleton-like structure： Al2O3-rich submicron particles embedded in the TiO2-rich matrix） and solid-phase sintered regions （remained nanoparticles）. The microstructural characteristics of the liquid-phase sintered region are formed due to the selective melting of TiO2 nanoparticles during plasma spraying. On the other hand, the TiO2 and Al2O3 nanoparticles of the solid-phase sintered regions are all unmelted during plasma spraying. Due to the existence of nanostructured microstructures, the nanostructured coating has a higher microhardness, a lower friction coefficient, and a better wear resistance than the conventional coating.

High-temperature frictional wear behavior of MCrAlY-based coatings deposited by atmosphere plasma spraying

Al2O3-r2O03/NiCoCrAIYTa coatings were prepared via atmosphere plasma spraying （APS）. The microstructure and phase com- position of the coatings were analyzed by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, laser confocal scanning microsco- py （LSCM）, and transmission electron microscopy （TEM）. The dry frictional wear behavior of the coatings at 500℃ in static air was inves- tigated and compared with that of 0Cr25Ni20 steel. The results show that the coatings comprise the slatted layers of oxide phases, unmelted particles, and pores. The hot abrasive resistance of the coatings is enhanced compared to that of 0Cr25Ni20, and their mass loss is approxi- mately one-fifteenth that of 0Cr25Ni20 steel. The main wear failure mechanisms of the coatings are abrasive wear, fatigue wear, and adhe- sive wear.

Ni60-SiC Coating Prepared by Plasma Spraying, Plasma Re-melting and Plasma Spray Welding on Surface of Hot Forging Die

In order to produce the hear-resistant inner layer of hot-forging die, plasma spraying and plasma re-melting and plasma spray welding were adopted. Substrate material was W6Mo5Cr4V2, including 10%, 20%, 30% SiC ceramic powder used as coating material to obtain different Ni-based SiC alloys coating. Micro-structure and micro-hardness analysis of the coating layer were followed, as well as thermophysical properties for the coating layer were measured. The experimental results show that the coating prepared with 70% Ni60, 30% SiC powder has best properties with plasma spray welding, in which the micro-hardness can achieve 1100 HV, meanwhile can improve the thermal property of hot-forging die dramatically.

Investigation on in-flight particle velocity in supersonic plasma spraying

In-flight particle velocity and flux distribution were measured using CCD thermal spray monitor system during supersonic plasma spray processing with nano-structured Al_2O_3-TiO_2 feed stocks. According to the results of particle flux measurement, the largest radian of the divergent particle stream is about 0.2. Within the measuring range, top speed of in-flight particles reached 800m/s. Particle acceleration was accomplished within 4cm down stream of the nozzle. Average particle velocity (about 450m/s) exceeded local sound speed (340m/s) even at a mean standoff distance of 17cm. With increasing mean standoff distance, average velocity of in-flight particle decreased according to a parabolic rule approximately. Image diagnosis showed that the result of in-flight particle velocity measurement is credible.

Synthesis of NiCr_2O_4 spinel coatings with high emissivity by plasma spraying

Air plasma spraying （APS） was used to produce high emissivity coatings with a NiCr204 spinel structure. The relationship between the emissivity and the crystal structure was investigated. X-ray diffraction （XRD） analyses show that NiCr204 spinel has been fabri- cated with the space group Fd3m. Scanning electron microscope （SEM） photographs show that the coating consists of a laminated structure with homogeneous grains and high porosity because of the unique feature of plasma spraying. The emissivity measurement and Fourier transformation infrared radiation （FT-IR） spectra show that NiCr204 has a high emissivity of about 0.91 because of its special spinel structure APS is a suitable method to produce high emissivity coatings.

Characterization of NbSi_2–Al_2O_3 nanocomposite coatings prepared with plasma spraying mechanically alloyed powders

The present study characterized NbSi2-Al2O3 nanocomposite powders plasma-sprayed on Ti-6Al-4Vsubstrates. The powders were agglomerated to obtain suitable particle sizes for spraying. The agglomerated powders were then plasma-sprayed using atmospheric plasma spraying. The structural transformations of the powders along with the morphological and mechanical changes of the coatings were examined by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, and hard- ness testing. The results showed that after plasma spraying, the grain size increased, and the lattice strain decreased. However, the grain size of this compound after spraying was still in the nanometer range. The coating was uniform and exhibited good adhesion to the substrate. The microhardness and fracture toughness of the nanocomposite coating were higher than those of a nanostructured NbSi2 coating.

Effect of Auxiliary Gas Flow Parameters on Microstructure and Properties of Ta Coatings Prepared by Three-Cathode Atmosphere Plasma Spraying

Based on the three-cathode plasma spraying system,tantalum(Ta)coatings were pre-pared on the substrate of CuCrZr alloy.The effects of different auxiliary gas(helium)flow rates on the microstructure,phase composition,mechanical and wear resistance properties of Ta coatings were studied.The results showed that the oxidation degree of the coatings decreases first and then increases with the increase of the auxiliary gas flow.When the auxiliary gas flow rate is 70 L·min-1,the oxidation degree of the coating is the lowest,minimum value of the porosity is 0.21%,and the bonding strength reaches the maximum,59.3 MPa.At this time,the coating wear rate is 0.0012 mm^(3)·N^(-1)·m^(-1)with the best wear resistance.This indicates that the auxiliary gas flow has an important influence on the quality and surface mechanical properties of tantalum coating.

Microstructure and Properties of Plasma Spraying Boron Carbide Coating

Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young's modulus, comparing with that of the bulk materials, is explained by porosity . The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.

Preparation of Ni60-Cr_3C_2 Coating by Plasma Spraying,Plasma Re-melting and Plasma Spray Welding on W6Mo5Cr4V2

In order to prepare heatresistant inner layer of hot-forging die, plasma spraying, plasma re- melting and plasma spray welding were adopted. Cr3C2 coatings of Ni-Based were prepared respectively with 10%, 20% and 30% Cr3C2 powder and W6Mo5Cr4V2 substrate. The coating microstructure analysis, the micro-hardness test, and the measurement of thermal parameters of coating were conducted. The experimental results show that the coating has the better thermo-physical property by using plasma spray welding method with the powder ratio of 90% Ni60 and 10% Cr3C2, and by this way the micro-hardness of coating can achieve 1100 HV.

Plasma spraying system with distributed controlling

A distributed control system is designed for plasma spraying equipment and the configurations of system software and hardware is discussed. Through founding an expert database, the spraying process parameters are worked out and the initialization and control of spraying process are realized. The plasma spraying system with this control configuration can simplify the spraying operation, improve automation level of spray process, and approach the experience criterion as soon as possible.

PLASMA SPRAYING TECHNOLOGY AND ITS APPLICATION

The development of plasma spraying technology since the ITSC' 95 conference is briefly summarized. Emphasis is placed on the new achievements of plasma spraying materials, processing, coating properties , facilities and application. The state of the plasma spraying technology in China is also introduced in the paper.

Oxidation Performance of Ytterbium Disilicate/Silicon Environmental Barrier Coating via Optimized Air Plasma Spraying

Environmental barrier coatings (EBCs) play a critical role in mitigating the degradation of SiCf/SiC ceramic matrix composites (CMCs) in complex combustion environment, and improve the service life of thermal engine components. In this paper, by adjusting the parameters of atmospheric plasma spraying (APS), the spraying process of ytterbium disilicate (Yb2Si2O7) under a lower power has been optimized. A two-layer EBC system consisting of ytterbium disilicate and silicon is prepared on the SiCf/SiC composite substrate by using optimized technological parameters. The thermal resistance and water oxygen corrosion resistance of such two-layer EBC system are investigated. The results indicate that the current ytterbium disilicate/silicon EBC system exhibits good phase stability, excellent water vapor and oxygen corrosion resistance. However, the exposed silicon bonding layer tends to generate an excessive thermal growth oxide (TGO) layer known as SiO2, leading to an early spallation of the coating.

Characteristics of Plasma Spraying Torch with a Hollow Cathode

A kind of plasma spraying torch with a hollow cathode is described in this paper. The plasma torch can be used for axial powder injection in plasma spray studies. The arc characteristics of the plasma torch with vacuous gas flowrates, different gas media, are presented. The mathematical modeling and computational method are developed for predicting the temperature and velocity field inside the plasma torch.

Micro-nano structured functional coatings deposited by liquid plasma spraying

Inspired by the micro-nano structure on the surface of biological materials or living organisms,micro-nano structure has been widely investigated in the field of functional coatings.Due to its large specific surface area,porosity,and dual-scale structure,it has recently attracted special attention.The typical fabrication processes of micro-nano structured coatings include sol-gel,hydrothermal synthesis,chemical vapor deposition,etc.This paper presents the main features of a recent deposition and synthesis technique,liquid plasma spraying(LPS).LPS is an important technical improvement of atmospheric plasma spraying.Compared with atmospheric plasma spraying,LPS is more suitable for preparing functional coatings with micro-nano structure.Micro-nano structured coatings are mainly classified into hierarchical-structure and binary-structure.The present study reviews the preparation technology,structural characteristics,functional properties,and potential applications of LPS coatings with a micro-nano structure.The micro-nano structured coatings obtained through tailoring the structure will present excellent performances.

Influence of Silver Contents on the Tribological Properties of Ni-Based Self-Lubricating Coatings by Atmospheric Plasma Spraying

The NiCrAlY-Mo-Ag composite coatings were prepared by atmospheric plasma spraying. The tribological properties of the composite coatings were investigated from 25 to 900 ℃ in details. The tribo-layer formed on the worn surface of the composite coatings and influenced the tribological properties at different temperatures. The addition of silver could effectively decrease the friction coefficient and wear rate of the coatings at the wide range of temperature. The rubbing process could form the nickel molybdate and promote the formation of silver molybdate within the worn surfaces at high temperature. The synergistic lubricating effects of nickel molybdate and silver molybdate are attributed to the improvement of the tribological properties of coatings at high temperature.

Mullite Oxidation Resistant Coating for SiC-coated Carbon/Carbon Composites by Supersonic Plasma Spraying

To improve the oxidation resistance of carbon/carbon （C/C） composites, mullite coating was prepared on the surface of SiC-coated C/C composites by supersonic plasma spraying. Phases and microstructures of mullite coating were characterized by X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The coating primarily consists of a single phase of mullite （3AI203-2SIO2）. The SEM results show that mullite coating was continuous and well bonded with the SiC inner layer without penetrating crack. Mullite coating exhibited good oxidation resistance, After 98.5 h oxidation at 1773 K and 9 thermal shock cycles between 1773 K and room temperature, the weight loss of the coated C/C composites was only 2.57%.

Influence of Surface Change of Substrate Due to Impacting Behavior of Plasma Spraying Particles

In this paper,the process of many particles hitting the same point of the substrate has been studied and an approximated formula to estimate maximum number of impact on the same point has been obtained through analytical analysis.Particles number of impacting on the same point of substrate;ust be small than this critical number to prevent substrate failure.The calculation results shows that for 45 steel,it is 21 when initial velocity is 40m/s,15 when initial velocity is 60 m/s,12 when initial velocity is 80 m/s and 4 when initial velocity is 240 m/s.With the increase of the particles initial velocity,the maximum number of speculation by the analytical model becomes linear.Accordingly we can deduce that this treatment does not cause the damage of substrate material.