Irregular phase-space orbits of the electrons are harmful to the electron-beam transport quality and hence deteriorate the performance of a free-electron laser (FEL). In previous literature, it was demonstrated that...Irregular phase-space orbits of the electrons are harmful to the electron-beam transport quality and hence deteriorate the performance of a free-electron laser (FEL). In previous literature, it was demonstrated that the irregularity of the electron phase-space orbits could be caused in several ways, such as varying the wiggler amplitude and inducing sidebands. Based on a Hamiltonian model with a set of self-consistent differential equations, it is shown in this paper that the electron- beam normalized plasma frequency functions not only couple the electron motion with the FEL wave, which results in the evolution of the FEL wave field and a possible power saturation at a large beam current, but also cause the irregularity of the electron phase-space orbits when the normalized plasma frequency has a sufficiently large value, even if the initial energy of the electron is equal to the synchronous energy or the FEL wave does not reach power saturation.展开更多
Deep sub-wavelength metamaterials are the key to the further development of practical metamaterials with small volumes and broadband properties. We propose to reduce the electrical sizes of metamaterials down to more ...Deep sub-wavelength metamaterials are the key to the further development of practical metamaterials with small volumes and broadband properties. We propose to reduce the electrical sizes of metamaterials down to more sub-wavelength scales by lowering the plasma frequencies of metallic wires. The theoretical model is firstly established by analyzing the plasma frequency of continuous thin wires. By introducing more inductance elements, the effective electron mass can be enhanced drastically, leading to significantly lowered plasma frequencies. Based on this theory, we demonstrate that both the electric and the magnetic plasma frequencies of metamaterials can be lowered significantly and thus the electrical sizes of metamaterials can be reduced to more sub-wavelength scales. This provides an efficient route to deep sub-wavelength metamaterials and will give rigorous impetus for the further development of practical metamaterials.展开更多
We report an optical spectroscopy study on LaSb, a compound recently identified to exhibit extremely large magnetoresistance. Our optieal measurement indicates that the material has a low carrier density. More inter- ...We report an optical spectroscopy study on LaSb, a compound recently identified to exhibit extremely large magnetoresistance. Our optieal measurement indicates that the material has a low carrier density. More inter- estingly, the study reveals that the plasma frequency increases with decreasing temperature. This phenomenon suggests either an increase of the conducting carrier density or/and a decrease of the effective mass of carriers with decreasing temperature. We attribute it primarily to the latter effect. Two possible scenarios on its physical origin are examined and discussed. The study offers new insight into the electronic structure of this compound.展开更多
The present study aims at the numerical simulations of the melting process of cerium oxide particles in RF thermal plasma.The physical model and the calculating method were described firstly;the interaction between ce...The present study aims at the numerical simulations of the melting process of cerium oxide particles in RF thermal plasma.The physical model and the calculating method were described firstly;the interaction between cerium oxide particles and plasma was analyzed;specific attention was given to the effects of particle initial size,injection velocity on the particle melting and trajectory in plasma.The influence of the temperature field and velocity field distribution of the plasma around the particle trajectory on the melting effect is analyzed,and the relationship between the heat absorption efficiency of the particles and the particle size reduction process is further determined.It is also found that there exists an optimal particle initial injection velocity which led to a more concentrated final particle size distribution and a more significant reduction of particle size.The results could provide effective guidance for understanding the plasma spheroidization process of uranium dioxide and cerium dioxide powder particles.展开更多
This paper deals with wave propagation and power coupling in blue-core helicon plasma driven by various antennas and frequencies.It is found that compared to non-blue-core mode,for blue-core mode,the wave can propagat...This paper deals with wave propagation and power coupling in blue-core helicon plasma driven by various antennas and frequencies.It is found that compared to non-blue-core mode,for blue-core mode,the wave can propagate in the core region,and it decays sharply outside the core.The power absorption is lower and steeper in radius for blue-core mode.Regarding the effects of antenna geometry for blue-core mode,it shows that half helix antenna yields the strongest wave field and power absorption,while loop antenna yields the lowest.Moreover,near axis,for antennas with m=+1,the wave field increases with axial distance.In the core region,the wave number approaches to a saturation value at much lower frequency for non-blue-core mode compared to blue-core mode.The total loading resistance is much lower for blue-core mode.These findings are valuable to understanding the physics of blue-core helicon discharge and optimizing the experimental performance of blue-core helicon plasma sources for applications such as space propulsion and material treatment.展开更多
To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency(RF) plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in th...To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency(RF) plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m^3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 μm, and the tap density is increased from 2.7 to 6.2 g/cm^3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.展开更多
Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon (mc-Si) surface texturing. In this paper,...Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon (mc-Si) surface texturing. In this paper, capacitively coupled plasma (CCP) driven by a dual frequency (DF) of 40.68 MHz and 13.56 MHz is first used for plasma texturing of mc-Si with SF6/O2 gas mixture. Using a hairpin resonant probe and optical emission techniques, DF-CCP characteristics and their influence on mc-silicon surface plasma texturing are investigated at different flow rate ratios, pressures, and radio-frequency (RF) input powers. Experimental results show that suitable plasma texturing of mc-silicon occurs only in a narrow range of plasma parameters, where electron density ne must be larger than 6.3 x 109 cm-3 and the spectral intensity ratio of the F atom to that of the O atom ([F]/[O]) in the plasma must be between 0.8 and 0.3. Out of this range, no cone-like structure is formed on the mc-silicon surface. In our experiments, the lowest reflectance of about 7.3% for mc-silicon surface texturing is obtained at an [F]/[O] of 0.5 and ne of 6.9 × 109 cm-3.展开更多
Methane conversion in the presence of oxygen under low-temperature radio frequency (RF) plasma was investigated.The experiment results indicated that the following four factors,i.e.,discharge voltage,discharge area,...Methane conversion in the presence of oxygen under low-temperature radio frequency (RF) plasma was investigated.The experiment results indicated that the following four factors,i.e.,discharge voltage,discharge area,O2/CH4 molar ratio and total gas flowrate,affected remarkably the reaction performance.The optimum reaction conditions of methane conversion in the presence of O2 under RF plasma are as follows:discharge voltage 1050 V,discharge area 989.1mm 2,O2/CH4 molar ratio 1/10 and total gas flowrate 200 ml/min.A methane conversion of 91% could be reached under the optimum conditions.Oxygen is good for the breaking of C-H bonds and also acts as a sort of thinner.According to the low-temperature plasma characteristics,the macroscopic kinetics model of methane conversion in the presence of O2 under radio frequency plasma was studied.展开更多
This paper reports on an experiment designed to test electromagnetic(EM)attenuation by radio-frequency(RF)plasma for cavity structures.A plasma reactor,in the shape of a hollow cylinder,filled with argon gas at lo...This paper reports on an experiment designed to test electromagnetic(EM)attenuation by radio-frequency(RF)plasma for cavity structures.A plasma reactor,in the shape of a hollow cylinder,filled with argon gas at low pressure,driven by a RF power source,was produced by wave-transmitting material.The detailed attenuations of EM waves were investigated under different conditions:the incident frequency is 1-4 GHz,the RF power supply is 13.56 MHz and1.6(-3) k W,and the argon pressure is 75-200 Pa.The experimental results indicate that 5-15 d B return loss can be obtained.From a first estimation,the electron density in the experiment is approximately(1.5-2.2)×1016m(-3)and the collision frequency is about 11(-3)0 GHz.The return loss of EM waves was calculated using a finite-difference time-domain(FDTD)method and it was found that it has a similar development with measurement.It can be confirmed that RF plasma is useful in the stealth of cavity structures such as jet-engine inlet.展开更多
The flashover performance of insulating materials plays an important role in the development of high-voltage insulation systems.In this paper,silicone rubber(SIR)is modified by CF4 radio frequency capacitively coupled...The flashover performance of insulating materials plays an important role in the development of high-voltage insulation systems.In this paper,silicone rubber(SIR)is modified by CF4 radio frequency capacitively coupled plasma(CCP)for the improvement of surface insulation performance.The discharge mode and active particles of CCP are diagnosed by the digital single-lens reflex and the spectrometer.Scanning electron microscopy and x-ray photoelectron spectroscopy are used for the surface physicochemical properties of samples,while the surface charge dissipation,charge accumulation measurement,and flashover test are applied for the surface electrical characteristics.Experimental results show that the fluorocarbon groups can be grafted and the surface roughness increases after plasma treatment.Besides,the surface charge dissipation is decelerated and the positive charge accumulation is inhibited obviously for the treated samples.Furthermore,the surface flashover voltage can be increased by 26.67%after 10 min of treatment.It is considered that strong electron affinity of C–F and increased surface roughness can contribute to deepening surface traps,which not only inhibits the development of secondary electron emission avalanche but also alleviates the surface charge accumulation and finally improves the surface flashover voltage of SIR.展开更多
The objectives of this research were to understand the process of converting toluene into phenol in a one-step process directly from a water–toluene mixture using the plasma in-liquid method.Experiments were conducte...The objectives of this research were to understand the process of converting toluene into phenol in a one-step process directly from a water–toluene mixture using the plasma in-liquid method.Experiments were conducted using 27.12 MHz radio frequency(RF) in-liquid plasma to decompose a solution of 30% toluene. Based on the experimental results as evaluated using gas chromatography–mass spectrometry(GC–MS), along with additional analysis by the Gaussian calculation, density functional theory(DFT) hybrid exchange–correlational functional(B3LYP)and 6-311 G basis, the phenol generated from toluene was quantified including any by-products.In the experiment, it was found that OH radicals from water molecules produced using RF inliquid plasma play a significant role in the chemical reaction with toluene. The experimental results suggest that phenol can be directly produced from a water–toluene mixture. The maximum phenol yields were 0.0013% and 0.0038% for irradiation times of 30s and 60s,respectively, at 120 W.展开更多
In order to improve the surface hydrophobicity, silicone rubber (SIR) samples were exposed to CF4 radio frequency (RF) capacitively coupled plasma (CCP). Attenuated total reflection Fourier transform infrared (...In order to improve the surface hydrophobicity, silicone rubber (SIR) samples were exposed to CF4 radio frequency (RF) capacitively coupled plasma (CCP). Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectrum and X-ray photoelectron spectroscopy (XPS) were used to observe the variation of the functional groups of the modified SIR. Static contact angle (SCA) was employed to estimate the change of hydrophobicity of the modified SIR. The surface energy of SIR is reduced largely from 27.37 mJ/m^2 of original SIR sample to 2.94 mJ/m^2 of SIR sample treated by CF4 CCP modification at RF power of 200 W for a treatment time of 5 rnin. According to the XPS, ATR-FTIR and surface energy analysis, it is suggested that the improvement of hydrophobicity on the modified SIR surface is mainly ascribed to the decrease of surface energy, which is caused by the cooperation of the fluosilicic structure of Si--F or Si--F2 and the fluoric groups of C--CFn induced by the methyl replacement reaction and residual methyl groups of SIR surface.展开更多
This paper presents the evolution of the electronegativity with the applied power during the E to H mode transition in a radio frequency(rf)inductively coupled plasma(ICP)in a mixture of Ar and O2.The densities of the...This paper presents the evolution of the electronegativity with the applied power during the E to H mode transition in a radio frequency(rf)inductively coupled plasma(ICP)in a mixture of Ar and O2.The densities of the negative ion and the electron,as well as their ratio,i.e.,the electronegativity,are measured as a function of the applied power by laser photo-detachment combined with a microwave resonance probe,under different pressures and O2 contents.Meanwhile,the optical emission intensities at Ar 750.4 nm and O 844.6 nm are monitored via a spectrograph.It was found that by increasing the applied power,the electron density and the optical emission intensity show a similar trench,i.e.,they increase abruptly at a threshold power,suggesting that the E to H mode transition occurs.With the increase of the pressure,the negative ion density presents opposite trends in the E-mode and the H-mode,which is related to the difference of the electron density and energy for the two modes.The emission intensities of Ar 750.4 nm and O 844.6 nm monotonously decrease with increasing the pressure or the O2 content,indicating that the density of high-energy electrons,which can excite atoms,is monotonically decreased.This leads to an increase of the negative ion density in the H-mode with increasing the pressure.Besides,as the applied power is increased,the electronegativity shows an abrupt drop during the E-to H-mode transition.展开更多
The properties of a helium atmospheric-pressure plasma jet(APPJ)are diagnosed with a dual assisted grounded electrode dielectric barrier discharge device.In the glow discharge,we captured the current waveforms at th...The properties of a helium atmospheric-pressure plasma jet(APPJ)are diagnosed with a dual assisted grounded electrode dielectric barrier discharge device.In the glow discharge,we captured the current waveforms at the positions of the three grounded rings.From the current waveforms,the time delay between the adjacent positions of the rings is employed to calculate the plasma bullet velocity of the helium APPJ.Moreover,the electron density is deduced from a model combining with the time delay and current intensity,which is about 10^(11)cm^(-3).In addition,The ion-neutral particles collision frequency in the radial direction is calculated from the current phase difference between two rings,which is on the order of 10~7 Hz.The results are helpful for understanding the basic properties of APPJs.展开更多
Aiming at studying the influence of actuating frequency on plasma assisted detonation initiation by alternating current dielectric barrier discharge, a loosely coupled method is used to simulate the detonation initiat...Aiming at studying the influence of actuating frequency on plasma assisted detonation initiation by alternating current dielectric barrier discharge, a loosely coupled method is used to simulate the detonation initiation process of a hydrogenoxygen mixture in a detonation tube at different actuating frequencies. Both the discharge products and the detonation forming process which is assisted by the plasma are analyzed. It is found that the patterns of the temporal and spatial distributions of discharge products in one cycle are not changed by the actuating frequency. However, the concentration of every species decreases as the actuating frequency rises, and atom O is the most sensitive to this variation, which is related to the decrease of discharge power. With respect to the reaction flow of the detonation tube, the deflagration-todetonation transition(DDT) time and distance both increase as the actuating frequency rises, but the degree of effect on DDT development during flow field evolution is erratic. Generally, the actuating frequency affects none of the amplitude value of the pressure, temperature, species concentration of the flow field, and the combustion degree within the reaction zone.展开更多
Plasma photonic crystals composed of periodic plasma and dielectric materials have attracted considerable attention because of their tunable photonic band gaps,but only their band structures or negative refractive ind...Plasma photonic crystals composed of periodic plasma and dielectric materials have attracted considerable attention because of their tunable photonic band gaps,but only their band structures or negative refractive index properties have been addressed in previous works.In this paper,through studying the transmission and reflection characteristics of two types of twodimensional plasma photonic crystals,it is found that plasma photonic crystals play an important role in absorbing waves,and they show broader band and higher amplitude absorption characteristics than bulk plasmas.Also,the absorption of plasma photonic crystals can be tuned via plasma parameters;varying the collision frequency can make the bandwidth and amplitude tunable,but cannot change the central frequency,whereas varying the plasma frequency would control both the location and the amplitude of the absorbers.These features of plasma photonic crystals have potential for terahertz tunable absorber applications.展开更多
During the plasma spheroidization process powders undergo different changes in their microstructures and crystal phases. In this paper, simple calculation of heat transfer between the plasma and a suspended particle w...During the plasma spheroidization process powders undergo different changes in their microstructures and crystal phases. In this paper, simple calculation of heat transfer between the plasma and a suspended particle was performed based on three hypotheses for the purpose of guiding experiments. Experimental investigation of the crystal phases and microstructural changes during the plasma processing was made using silica, alumina and nickel powders as starting materials. It has been revealed from the experimental results that these materials undergo different changes in crystal phases and microstructures, and these changes are essentially determined by the structures, properties and aggregate states of the starting materials.展开更多
A spherical Fe matrix composite powder containing a high volume fraction (82vo1%) of fine TiC reinforcement was produced using a novel process combining in situ synthesis and plasma techniques. The composite powder ...A spherical Fe matrix composite powder containing a high volume fraction (82vo1%) of fine TiC reinforcement was produced using a novel process combining in situ synthesis and plasma techniques. The composite powder exhibited good sphericity and a dense structure, and the fine sub-micron TiC particles were homogeneously distributed in the α-Fe matrix. A TiC-Fe cermet was prepared from the as-prepared spherical composite powder using powder metallurgy at a low sintering temperature; the product exhibited a hardness of HRA 88.5 and a flexural strength of 1360 MPa. The grain size of the fine-grained TiC and special surface structure of the spherical powder played the key roles in the fabrication process.展开更多
The growing interest in additive manufacturing of GH4169 alloy was accompanied by the demand on spherical GH4169 powders with high performance.The powder particles were treated by radio frequency plasma with the diffe...The growing interest in additive manufacturing of GH4169 alloy was accompanied by the demand on spherical GH4169 powders with high performance.The powder particles were treated by radio frequency plasma with the different feeding rates.The microstructure and morphology,the particle size distribution of as-treated powders were studied by scanning electron microscopy and laser particle size analysis.It was demonstrated that GH4169 powders with extremely fine followability were obtained by radio frequency plasma spheroidization technology.With the same plasma parameters,the spheroidization efficiency of the particles varied with the feeding rates.When the rate of the powder feeding rates was too small,the excessive absorption of the heating by the powders caused vaporization,then the collection decreased.When the feeding rates was too large,the powder particles were insufficiently absorbed,resulting in defects in the powders.The microstructure of the as-treated spherical particles was mainly cell crystals,columnar crystals,and even microcrystals.Under the suitable plasma parameters,the resulting powders haved a slightly increased average particle size,excellent spheroidization,surface smoothness,followability,and bulk ratio.展开更多
Radio frequency (RF) underwater discharge operation was performed for different liquid conductivities driven by different frequencies ranging from 13.56 MHz to 60 MHz, and its application to organic degradation was ...Radio frequency (RF) underwater discharge operation was performed for different liquid conductivities driven by different frequencies ranging from 13.56 MHz to 60 MHz, and its application to organic degradation was investigated. The RF underwater discharge was observed to be generated within the bubble at electrode surface formed by RF and plasma heating. It was shown that the sizes of the bubbles and plasmas increased as the driving frequency and the input power went up. The breakdown voltage decreased rapidly with the increase of the water conductivity and driving frequency. Comparative experiments of the UV-VIS absorbance spectra of Congo Red solution before and after discharge suggested effective degradation of the organic dye due to the active species generated during the discharge, such as .OH, .O, .H, etc. revealed by optical emission spectroscopy. The results show that higher exciting frequency and lower conduc- tivity of the solution are more effective for organic degradation. With the combination of Fourier Transform Infrared Spectroscopy (FT-IR) and Liquid Chromatography-Mass Spectrometry (LC- MS) data, one possible degradation process was proposed and the main conceivable components and structures of the products were also presented.展开更多
基金Project supported by the Science Foundation of Department of Education of Sichuan Province,China (Grant No.12233454)the Youth Foundation of Department of Education of Sichuan Province,China (Grant No.10ZB080)the Xihua University Foundation,China (Grant No.Z0913306)
文摘Irregular phase-space orbits of the electrons are harmful to the electron-beam transport quality and hence deteriorate the performance of a free-electron laser (FEL). In previous literature, it was demonstrated that the irregularity of the electron phase-space orbits could be caused in several ways, such as varying the wiggler amplitude and inducing sidebands. Based on a Hamiltonian model with a set of self-consistent differential equations, it is shown in this paper that the electron- beam normalized plasma frequency functions not only couple the electron motion with the FEL wave, which results in the evolution of the FEL wave field and a possible power saturation at a large beam current, but also cause the irregularity of the electron phase-space orbits when the normalized plasma frequency has a sufficiently large value, even if the initial energy of the electron is equal to the synchronous energy or the FEL wave does not reach power saturation.
基金supported by the National Natural Science Foundation of China(Grants Nos.11204378 and 11274389)the Natural Science Foundation of Shaanxi Province,China(Grant No.2011JQ8031)
文摘Deep sub-wavelength metamaterials are the key to the further development of practical metamaterials with small volumes and broadband properties. We propose to reduce the electrical sizes of metamaterials down to more sub-wavelength scales by lowering the plasma frequencies of metallic wires. The theoretical model is firstly established by analyzing the plasma frequency of continuous thin wires. By introducing more inductance elements, the effective electron mass can be enhanced drastically, leading to significantly lowered plasma frequencies. Based on this theory, we demonstrate that both the electric and the magnetic plasma frequencies of metamaterials can be lowered significantly and thus the electrical sizes of metamaterials can be reduced to more sub-wavelength scales. This provides an efficient route to deep sub-wavelength metamaterials and will give rigorous impetus for the further development of practical metamaterials.
基金Supported by the National Natural Science Foundation of China under Grant Nos 11327806 and GZ1123the National Key Research and Development Program of China under Grant No 2016YFA0300902
文摘We report an optical spectroscopy study on LaSb, a compound recently identified to exhibit extremely large magnetoresistance. Our optieal measurement indicates that the material has a low carrier density. More inter- estingly, the study reveals that the plasma frequency increases with decreasing temperature. This phenomenon suggests either an increase of the conducting carrier density or/and a decrease of the effective mass of carriers with decreasing temperature. We attribute it primarily to the latter effect. Two possible scenarios on its physical origin are examined and discussed. The study offers new insight into the electronic structure of this compound.
基金supported by National Natural Science Foundation of China(No.11875039)。
文摘The present study aims at the numerical simulations of the melting process of cerium oxide particles in RF thermal plasma.The physical model and the calculating method were described firstly;the interaction between cerium oxide particles and plasma was analyzed;specific attention was given to the effects of particle initial size,injection velocity on the particle melting and trajectory in plasma.The influence of the temperature field and velocity field distribution of the plasma around the particle trajectory on the melting effect is analyzed,and the relationship between the heat absorption efficiency of the particles and the particle size reduction process is further determined.It is also found that there exists an optimal particle initial injection velocity which led to a more concentrated final particle size distribution and a more significant reduction of particle size.The results could provide effective guidance for understanding the plasma spheroidization process of uranium dioxide and cerium dioxide powder particles.
基金Project supported by the National Natural Science Foundation of China(Grant No.92271113)the Fundamental Research Funds for the Central Universities(Grant No.2022CDJQY-003)+1 种基金Chongqing Entrepreneurship and Innovation Support Program for Overseas Returnees(Grant No.CX2022004)the Fund from Shanghai Engineering Research Center of Space Engine(Grant No.17DZ2280800).
文摘This paper deals with wave propagation and power coupling in blue-core helicon plasma driven by various antennas and frequencies.It is found that compared to non-blue-core mode,for blue-core mode,the wave can propagate in the core region,and it decays sharply outside the core.The power absorption is lower and steeper in radius for blue-core mode.Regarding the effects of antenna geometry for blue-core mode,it shows that half helix antenna yields the strongest wave field and power absorption,while loop antenna yields the lowest.Moreover,near axis,for antennas with m=+1,the wave field increases with axial distance.In the core region,the wave number approaches to a saturation value at much lower frequency for non-blue-core mode compared to blue-core mode.The total loading resistance is much lower for blue-core mode.These findings are valuable to understanding the physics of blue-core helicon discharge and optimizing the experimental performance of blue-core helicon plasma sources for applications such as space propulsion and material treatment.
基金financially supported by the 2012 Western Materials Innovation Foundation of China (No. XBCL-1-06)the Science and Technology Coordinating Innovative Engineering Project of Shaanxi Province of China (No. 2014KTCQ01-35)+1 种基金the Natural Science Foundation of Shaanxi Province of China (No. 2014JM6226)the Specialized Research Fund of Education Commission of Shaanxi Province of China (No. 2013JK0905)
文摘To control the morphology and particle size of dense spherical molybdenum powder prepared by radio frequency(RF) plasma from irregular molybdenum powder as a precursor, plasma process parameters were optimized in this paper. The effects of the carrier gas flow rate and molybdenum powder feeding rate on the shape and size of the final products were studied. The molybdenum powder morphology was examined using high-resolution scanning electron microscopy. The powder phases were analyzed by X-ray diffraction. The tap density and apparent density of the molybdenum powder were investigated using a Hall flow meter and a Scott volumeter. The optimal process parameters for the spherical molybdenum powder preparation are 50 g/min powder feeding rate and 0.6 m^3/h carrier gas rate. In addition, pure spherical molybdenum powder can be obtained from irregular powder, and the tap density is enhanced after plasma processing. The average size is reduced from 72 to 62 μm, and the tap density is increased from 2.7 to 6.2 g/cm^3. Therefore, RF plasma is a promising method for the preparation of high-density and high-purity spherical powders.
基金supported by the Prospective Project of Industry–University–Research Institution of Jiangsu Province,China(Grant No.BY2010125)the National Natural Science Foundation of China(Grant No.11175127)
文摘Due to it being environmentally friendly, much attention has been paid to the dry plasma texturing technique serving as an alternative candidate for multicrystalline silicon (mc-Si) surface texturing. In this paper, capacitively coupled plasma (CCP) driven by a dual frequency (DF) of 40.68 MHz and 13.56 MHz is first used for plasma texturing of mc-Si with SF6/O2 gas mixture. Using a hairpin resonant probe and optical emission techniques, DF-CCP characteristics and their influence on mc-silicon surface plasma texturing are investigated at different flow rate ratios, pressures, and radio-frequency (RF) input powers. Experimental results show that suitable plasma texturing of mc-silicon occurs only in a narrow range of plasma parameters, where electron density ne must be larger than 6.3 x 109 cm-3 and the spectral intensity ratio of the F atom to that of the O atom ([F]/[O]) in the plasma must be between 0.8 and 0.3. Out of this range, no cone-like structure is formed on the mc-silicon surface. In our experiments, the lowest reflectance of about 7.3% for mc-silicon surface texturing is obtained at an [F]/[O] of 0.5 and ne of 6.9 × 109 cm-3.
文摘Methane conversion in the presence of oxygen under low-temperature radio frequency (RF) plasma was investigated.The experiment results indicated that the following four factors,i.e.,discharge voltage,discharge area,O2/CH4 molar ratio and total gas flowrate,affected remarkably the reaction performance.The optimum reaction conditions of methane conversion in the presence of O2 under RF plasma are as follows:discharge voltage 1050 V,discharge area 989.1mm 2,O2/CH4 molar ratio 1/10 and total gas flowrate 200 ml/min.A methane conversion of 91% could be reached under the optimum conditions.Oxygen is good for the breaking of C-H bonds and also acts as a sort of thinner.According to the low-temperature plasma characteristics,the macroscopic kinetics model of methane conversion in the presence of O2 under radio frequency plasma was studied.
基金supported by National Natural Science Foundation of China(No.51107033)the Fundamental Research Funds for the Central Universities of China(No.2013B33614)
文摘This paper reports on an experiment designed to test electromagnetic(EM)attenuation by radio-frequency(RF)plasma for cavity structures.A plasma reactor,in the shape of a hollow cylinder,filled with argon gas at low pressure,driven by a RF power source,was produced by wave-transmitting material.The detailed attenuations of EM waves were investigated under different conditions:the incident frequency is 1-4 GHz,the RF power supply is 13.56 MHz and1.6(-3) k W,and the argon pressure is 75-200 Pa.The experimental results indicate that 5-15 d B return loss can be obtained.From a first estimation,the electron density in the experiment is approximately(1.5-2.2)×1016m(-3)and the collision frequency is about 11(-3)0 GHz.The return loss of EM waves was calculated using a finite-difference time-domain(FDTD)method and it was found that it has a similar development with measurement.It can be confirmed that RF plasma is useful in the stealth of cavity structures such as jet-engine inlet.
基金supported by National Natural Science Foundation of China(Nos.11775175,U1766218,51827809)Natural Science Research Fund of Higher Education of Anhui Province(No.KJ2020A0246)。
文摘The flashover performance of insulating materials plays an important role in the development of high-voltage insulation systems.In this paper,silicone rubber(SIR)is modified by CF4 radio frequency capacitively coupled plasma(CCP)for the improvement of surface insulation performance.The discharge mode and active particles of CCP are diagnosed by the digital single-lens reflex and the spectrometer.Scanning electron microscopy and x-ray photoelectron spectroscopy are used for the surface physicochemical properties of samples,while the surface charge dissipation,charge accumulation measurement,and flashover test are applied for the surface electrical characteristics.Experimental results show that the fluorocarbon groups can be grafted and the surface roughness increases after plasma treatment.Besides,the surface charge dissipation is decelerated and the positive charge accumulation is inhibited obviously for the treated samples.Furthermore,the surface flashover voltage can be increased by 26.67%after 10 min of treatment.It is considered that strong electron affinity of C–F and increased surface roughness can contribute to deepening surface traps,which not only inhibits the development of secondary electron emission avalanche but also alleviates the surface charge accumulation and finally improves the surface flashover voltage of SIR.
基金partially supported by JSPS KAKENHI Grant Number 15K05833
文摘The objectives of this research were to understand the process of converting toluene into phenol in a one-step process directly from a water–toluene mixture using the plasma in-liquid method.Experiments were conducted using 27.12 MHz radio frequency(RF) in-liquid plasma to decompose a solution of 30% toluene. Based on the experimental results as evaluated using gas chromatography–mass spectrometry(GC–MS), along with additional analysis by the Gaussian calculation, density functional theory(DFT) hybrid exchange–correlational functional(B3LYP)and 6-311 G basis, the phenol generated from toluene was quantified including any by-products.In the experiment, it was found that OH radicals from water molecules produced using RF inliquid plasma play a significant role in the chemical reaction with toluene. The experimental results suggest that phenol can be directly produced from a water–toluene mixture. The maximum phenol yields were 0.0013% and 0.0038% for irradiation times of 30s and 60s,respectively, at 120 W.
基金Project(05JT1034) supported by the Plan of Science and Technology Bureau of Hunan Province,China
文摘In order to improve the surface hydrophobicity, silicone rubber (SIR) samples were exposed to CF4 radio frequency (RF) capacitively coupled plasma (CCP). Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectrum and X-ray photoelectron spectroscopy (XPS) were used to observe the variation of the functional groups of the modified SIR. Static contact angle (SCA) was employed to estimate the change of hydrophobicity of the modified SIR. The surface energy of SIR is reduced largely from 27.37 mJ/m^2 of original SIR sample to 2.94 mJ/m^2 of SIR sample treated by CF4 CCP modification at RF power of 200 W for a treatment time of 5 rnin. According to the XPS, ATR-FTIR and surface energy analysis, it is suggested that the improvement of hydrophobicity on the modified SIR surface is mainly ascribed to the decrease of surface energy, which is caused by the cooperation of the fluosilicic structure of Si--F or Si--F2 and the fluoric groups of C--CFn induced by the methyl replacement reaction and residual methyl groups of SIR surface.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.11675039,11875101,and 11935005)the Fundamental Research Founds for the Central Universities,China(Grant Nos.DUT18TD06 and DUT20LAB201).
文摘This paper presents the evolution of the electronegativity with the applied power during the E to H mode transition in a radio frequency(rf)inductively coupled plasma(ICP)in a mixture of Ar and O2.The densities of the negative ion and the electron,as well as their ratio,i.e.,the electronegativity,are measured as a function of the applied power by laser photo-detachment combined with a microwave resonance probe,under different pressures and O2 contents.Meanwhile,the optical emission intensities at Ar 750.4 nm and O 844.6 nm are monitored via a spectrograph.It was found that by increasing the applied power,the electron density and the optical emission intensity show a similar trench,i.e.,they increase abruptly at a threshold power,suggesting that the E to H mode transition occurs.With the increase of the pressure,the negative ion density presents opposite trends in the E-mode and the H-mode,which is related to the difference of the electron density and energy for the two modes.The emission intensities of Ar 750.4 nm and O 844.6 nm monotonously decrease with increasing the pressure or the O2 content,indicating that the density of high-energy electrons,which can excite atoms,is monotonically decreased.This leads to an increase of the negative ion density in the H-mode with increasing the pressure.Besides,as the applied power is increased,the electronegativity shows an abrupt drop during the E-to H-mode transition.
基金supported by National Natural Science Foundation of China(No.11105093)the Technological Project of Shenzhen,China(No.JC201005280485A)the Planned S&T Program of Shenzhen,China(No.JC201105170703A)
文摘The properties of a helium atmospheric-pressure plasma jet(APPJ)are diagnosed with a dual assisted grounded electrode dielectric barrier discharge device.In the glow discharge,we captured the current waveforms at the positions of the three grounded rings.From the current waveforms,the time delay between the adjacent positions of the rings is employed to calculate the plasma bullet velocity of the helium APPJ.Moreover,the electron density is deduced from a model combining with the time delay and current intensity,which is about 10^(11)cm^(-3).In addition,The ion-neutral particles collision frequency in the radial direction is calculated from the current phase difference between two rings,which is on the order of 10~7 Hz.The results are helpful for understanding the basic properties of APPJs.
基金Project supported by the Open Project of Science and Technology on Scramjet Laboratory,China(Grant No.CG-2014-05-118)the National Natural Science Foundation of China(Grant No.91441123)
文摘Aiming at studying the influence of actuating frequency on plasma assisted detonation initiation by alternating current dielectric barrier discharge, a loosely coupled method is used to simulate the detonation initiation process of a hydrogenoxygen mixture in a detonation tube at different actuating frequencies. Both the discharge products and the detonation forming process which is assisted by the plasma are analyzed. It is found that the patterns of the temporal and spatial distributions of discharge products in one cycle are not changed by the actuating frequency. However, the concentration of every species decreases as the actuating frequency rises, and atom O is the most sensitive to this variation, which is related to the decrease of discharge power. With respect to the reaction flow of the detonation tube, the deflagration-todetonation transition(DDT) time and distance both increase as the actuating frequency rises, but the degree of effect on DDT development during flow field evolution is erratic. Generally, the actuating frequency affects none of the amplitude value of the pressure, temperature, species concentration of the flow field, and the combustion degree within the reaction zone.
基金supported by National Natural Science Foundation of China(Nos.61107030,11174280,60990323 and 60990320)the Promotive Research Fund for Excellent Young and Middle-aged Scientists of Shandong Province(No.BS2010CL025)the China Postdoctoral Science Foundation
文摘Plasma photonic crystals composed of periodic plasma and dielectric materials have attracted considerable attention because of their tunable photonic band gaps,but only their band structures or negative refractive index properties have been addressed in previous works.In this paper,through studying the transmission and reflection characteristics of two types of twodimensional plasma photonic crystals,it is found that plasma photonic crystals play an important role in absorbing waves,and they show broader band and higher amplitude absorption characteristics than bulk plasmas.Also,the absorption of plasma photonic crystals can be tuned via plasma parameters;varying the collision frequency can make the bandwidth and amplitude tunable,but cannot change the central frequency,whereas varying the plasma frequency would control both the location and the amplitude of the absorbers.These features of plasma photonic crystals have potential for terahertz tunable absorber applications.
基金supported by National Natural Science Foundation of China (No.50574083)
文摘During the plasma spheroidization process powders undergo different changes in their microstructures and crystal phases. In this paper, simple calculation of heat transfer between the plasma and a suspended particle was performed based on three hypotheses for the purpose of guiding experiments. Experimental investigation of the crystal phases and microstructural changes during the plasma processing was made using silica, alumina and nickel powders as starting materials. It has been revealed from the experimental results that these materials undergo different changes in crystal phases and microstructures, and these changes are essentially determined by the structures, properties and aggregate states of the starting materials.
基金financially supported by the National Natural Science Foundation of China (No. 51274039)the Research Fund for the Doctoral Program of Higher Education of China (No. 20120006110007)
文摘A spherical Fe matrix composite powder containing a high volume fraction (82vo1%) of fine TiC reinforcement was produced using a novel process combining in situ synthesis and plasma techniques. The composite powder exhibited good sphericity and a dense structure, and the fine sub-micron TiC particles were homogeneously distributed in the α-Fe matrix. A TiC-Fe cermet was prepared from the as-prepared spherical composite powder using powder metallurgy at a low sintering temperature; the product exhibited a hardness of HRA 88.5 and a flexural strength of 1360 MPa. The grain size of the fine-grained TiC and special surface structure of the spherical powder played the key roles in the fabrication process.
基金supported financially by Yangjiang City Hardware Knives and Scissors and Nickel Alloy Industry Additive Manufacturing Technology Innovation Platform Construction(No.2015B020221002)Guangdong Province‘Sailing Plan’Introduces Special Funding for Innovation and Entrepreneurship Team(No.2015YT02G090)+1 种基金High-end Knives and Scissors Additive Manufacturing(3D Printing)of Engineering Technology Research Center in Guangdong Province(Grant No.509153168061)Initial Construction Subsidy for New Research and Development Institutions of Yangjiang City Hardware Knives and Scissors Industry and Technology Research(Grant No.611229498090)。
文摘The growing interest in additive manufacturing of GH4169 alloy was accompanied by the demand on spherical GH4169 powders with high performance.The powder particles were treated by radio frequency plasma with the different feeding rates.The microstructure and morphology,the particle size distribution of as-treated powders were studied by scanning electron microscopy and laser particle size analysis.It was demonstrated that GH4169 powders with extremely fine followability were obtained by radio frequency plasma spheroidization technology.With the same plasma parameters,the spheroidization efficiency of the particles varied with the feeding rates.When the rate of the powder feeding rates was too small,the excessive absorption of the heating by the powders caused vaporization,then the collection decreased.When the feeding rates was too large,the powder particles were insufficiently absorbed,resulting in defects in the powders.The microstructure of the as-treated spherical particles was mainly cell crystals,columnar crystals,and even microcrystals.Under the suitable plasma parameters,the resulting powders haved a slightly increased average particle size,excellent spheroidization,surface smoothness,followability,and bulk ratio.
基金supported by Natural Science Foundation of Jiangsu Education Committee of China (No.09KJA140005)
文摘Radio frequency (RF) underwater discharge operation was performed for different liquid conductivities driven by different frequencies ranging from 13.56 MHz to 60 MHz, and its application to organic degradation was investigated. The RF underwater discharge was observed to be generated within the bubble at electrode surface formed by RF and plasma heating. It was shown that the sizes of the bubbles and plasmas increased as the driving frequency and the input power went up. The breakdown voltage decreased rapidly with the increase of the water conductivity and driving frequency. Comparative experiments of the UV-VIS absorbance spectra of Congo Red solution before and after discharge suggested effective degradation of the organic dye due to the active species generated during the discharge, such as .OH, .O, .H, etc. revealed by optical emission spectroscopy. The results show that higher exciting frequency and lower conduc- tivity of the solution are more effective for organic degradation. With the combination of Fourier Transform Infrared Spectroscopy (FT-IR) and Liquid Chromatography-Mass Spectrometry (LC- MS) data, one possible degradation process was proposed and the main conceivable components and structures of the products were also presented.