Effects of Ce in novel bronze and its plasma sprayed coating

A novel aluminum bronze over the Cu-Al binary alloy eutectoid Cu-14Al-4.5Fe was prepared by a jointly-charging one-melting technique and conventional sand casting. The bronze coatings were atmospherically plasma sprayed on the 45# medium carbon steel substrate. The effect of rare earth Ce on the microstructures and Vickers hardness of the cast alloy and coatings were characterized by scanning electron microscopy, X-ray diffraction, electronic probe microanalysis, transmission electron microscopy and microhardness measurements. The results indicate that the hardness of both as-cast alloy and coating are enhanced by the addition of 0.6% Ce due to the refinement of κ phases which are well distributed in the matrix. The rapid solidification in the plasma spray processing retains Fe-supersaturated in the Al-bronze alloy coatings, which avoids the formation of eutectoid （α＋γ2） phase and stacking faults are found in the coatings with Ce added, accordingly improves the mechanical properties.

The Study of the Grit-blasting Parameters and Their Effects on the Adhesive Strength of the Plasma Sprayed Coatings

Surface Preparation is very important in adhesive b on ding of spray coatings to the surface of a work piece. The common practice is gr it-blasting of the surface before subjecting it to the spray coating process. In this study, grit-blasting of an AISI 4130 steel (of different heat treatmen ts) with Al 2O 3 particles was studied. Various grit-blasting parameters such as blasting particle size, the distance between blasting nozzle and the work pi ece (25, 30 and 40 cm.), blasting pressure (3,4,5,6 and 7 bars), blasting time ( 3, 6 and 10 seconds), and the blasting angle (45° and 90°) were examined in or der to find the optimum roughness. The mean roughness (Ra) of the grit-blasted surfaces were measured and the vari ations of the roughness with respect to the above mentioned variables were studi ed. The results show that by increasing blasting time, surface roughness increas es up to a maximum and then slightly decreases it with further duration of t he process. On the other hand a lengthy blasting causes some undesirable results such as an increase in residual particles between surface irregularities. There fore an optimum blasting time is of great importance. Increasing the blasting pr essure also provides a rougher surface, but in grit blasting of harder specimens the surface roughness decreases when the pressure reaches a certain limit. About the blasting angle, it was noticed that an angle of 45° results in less r esidual particles between the surface irregularities, in comparison to the angle of 90°. After grit-blasting, the specimens were plasma spray coated with 80% ZrO 2-20 % Y 2O 3 powder. The adhesive strength of the coating to the substrate was the n measured according to the DIN 50160 standard. The results show that for a certain base metal, the adhesive strength is directl y related to the surface roughness of the base material. Residual particles afte r grit-blasting the surface of the specimens can also have a strong deteriorati ng effect on adhesive strength. Finally, it was shown that the hardness of the b ase material had a direct effect on the adhesive strength of the sprayed coating s.

Protection Performance of Plasma Sprayed Al_(2)O_(3)-13 wt%TiO_(2) Coating Sealed with an Organic-inorganic Hybrid Agent

An organic-inorganic hybrid sealing agent was fabricated and used in the plasma sprayed Al_(2)O_(3)-13 wt%TiO_(2)coating,and conventional silicone agent was also used for comparison.Protection performance of the coatings was comprehensively evaluated based on both anti-corrosion and anti-biofouling properties.The results reveal that the sealing treatment is remarkably useful to decrease the porosity of the coating,and the porosity of the coating sealed with the hybrid agent is only 0.035%.Immersion corrosion test and Tafel polarization test reveal that the sealed coating with the hybrid agent exhibits a better corrosion resistance by compared with the coating sealed with silicone agent.The corrosion current density i_(corr) of the hybrid agent sealed coating is only 0.7×10^(-6)A·cm^(-2).Moreover,anti-biofouling tests both in the outdoor analogue hydraulic environment and in the natural marine environment prove that the mentioned novel coating presents a better combination of corrosion resistance and anti-biofouling property by compared with the other coatings,and it could be used as a protection of metal components in the marine environment.

HOT CORROSION OF A PLASMA SPRAYED CoNiCrAlTaSiY COATING

Hot corrosion(HC) of the APS(atomospheric plasma spraying)CoNiCrAlTaSiY coating on a nickel-base superalloy GH864 has been studied. The effect of laser-treatment on hot corrosion resistance was also examined.It was shown that CoNiCrAlTaSiY coating had superior properties in resistance to hot corrosion due to the readiness of the formation of a protective Cr2O3 scale on the coating surface.A model for the mechanism of hot corrosion of this coating has been suggested. Hot corrosion resistance of this coating was significantly increased by the laser treatment simply because the surface of the as sprayed coating was densified by the high power laser beam.

Laser Remelting of Plasma Sprayed NiCrAlY and NiCrAlY-Al_2O_3 Coatings

Two types of plasma sprayed coatings (NiCrAlY and NiCrAlY-A12O3) were remelted by a 5 kW cw CO2 laser. With increasing laser power and decreasing traverse speed in the ranges of 200-700 W and 5-30 mm/s respectively, the melted track grew in width and depth. In the optimum range of laser parameters, a homogeneous remelted layer without voids, cavities, unmelted particles and microcracks was formed. On the surface of remelted layers, Al203 and YAIO3 were detected. As a result of isothermal oxidation tests, weight gains of laser remelted coatings were obviously lower than that only plasma sprayed, especially laser remelted NiCrAlY-Al2O3 coatings. The effects of laser remelting and incorporation of A12O3 second phase in N1CrAlY matrix on high temperature oxidation resistance were discussed.

Microstructure studies of air-plasma-spray-deposited CoNiCrAlY coatings before and after thermal cyclic loading for high-temperature application

In the present study, bond-coats for thermal barrier coatings were deposited via air plasma spraying（APS） techniques onto Inconel 800 and Hastelloy C-276 alloy substrates. Scanning electron microscopy（SEM）, transmission electron microscopy（TEM）, X-ray diffraction（XRD）, and atomic force microscopy（AFM） were used to investigate the phases and microstructure of the as-sprayed, APS-deposited Co Ni Cr Al Y bond-coatings. The aim of this work was to study the suitability of the bond-coat materials for high temperature applications. Confirmation of nanoscale grains of the γ/γ′-phase was obtained by TEM, high-resolution TEM, and AFM. We concluded that these changes result from the plastic deformation of the bond-coat during the deposition, resulting in Co Ni Cr Al Y bond-coatings with excellent thermal cyclic resistance suitable for use in high-temperature applications. Cyclic oxidative stability was observed to also depend on the underlying metallic alloy substrate.

Microstructure and Properties of Plasma Spraying Boron Carbide Coating

Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical, mechanical and electrical properties were measured. The results showed that high microhardness, modulus and low porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young's modulus, comparing with that of the bulk materials, is explained by porosity . The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.

PLASMA SPRAYING TECHNOLOGY AND ITS APPLICATION

The development of plasma spraying technology since the ITSC' 95 conference is briefly summarized. Emphasis is placed on the new achievements of plasma spraying materials, processing, coating properties , facilities and application. The state of the plasma spraying technology in China is also introduced in the paper.

Effect of Ni content on high power laser ablation behavior of coatings sprayed by Ni covering graphite/SiO2 powders

Faced with the challenge of high energy ablation problems, especially for laser ablation, effective energy dissipation protective materials fabricate by efficient preparation method is a feasible solution. The Ni-graphite/Si O2 coatings with different Ni content were prepared by plasma spraying method with optimized plasma spraying parameters. All coatings are pure without oxidation and dense. Their ablation behaviors were investigated by high power continuous wave laser. The results indicate that the Ni-graphite/Si O2 coating with appropriate Ni content could realize the purpose of energy consumption by endothermal reaction of graphite/Si O2 and reflection improvement. High Ni content will block the occurrence of endothermal reaction of graphite/Si O2 and increase the heat diffusion to interior part of coating, which can make the ablation situation of coating more serious.