Research on the Drawing-up of the Pole Figure for Orientation Analysis of Directional Si Steel Sheet

The magnetic property of soft magnetic metals and alloys depends strongly on the crystallo-graphic orientation. In automated equipment for orientation research, the intensity for drawing up the pole figure is measured in detail. The present research shows that the accurate pole figure can be drawn up without measuring concretely the intensity. For directional Si steel sheet the measuring step may be 4～5 degrees. In this paper the experimental equation for defo-cusing correction was derived from the experimental data in different specimens with random orientation.

CONSTRUCTING COMPLETE POLE FIGURE FROM AN INCOMPLETE ONE

An analytical procedure for rapidly and quantitatively constructing complete pole figures of cubic materials,based on the fundamental equations of the vector method.has been presented. Here.an incompletely measured pole figure can be completed by using its measured data as constraint conditions.It also allows the derivation of any other pole figures.

Effect of Sc and Zr on the in-plane anisotropy of Al-Mg-Mn alloy sheets

The Al-Mg-Mn alloy sheets with and without trace Sc and Zr were investigated by means of tensile test,X-ray diffraction,optical microscope,and transmission electron microscope.The indexes of in-plane anisotropy(IIPA)of their tensile mechanical properties were calculated and their inverse pole figures were obtained by Harris method.The two alloy sheets have the same law of in-plane anisotropy and remarkable in-plane anisotropy of mechanical properties,and the IIPA of the alloy sheet with Sc and Zr is bigger than that of the alloy sheet without Sc and Zr.The relationships of the in-plane anisotropy and the anisotropy of the crystallographic texture were analyzed based on the model of monocrystal.It is the common action of the anisotropy of crystallography and microstructures that causes the in-plane anisotropy of their mechanical properties,but the major cause is the{110}〈112〉crystallographic texture.The trace Sc and Zr can promote the formation and stabilization of the{110}〈112〉texture,inhibit the formation of the{100}〈001〉texture,and increase the in-plane anisotropy of the alloy sheet containing trace Sc and Zr.

Textures of high-strength and low-expansion Fe-Ni alloy wires during cold-drawing processes

Textures of high-strength and low-expansion Fe-Ni alloy wires during cold-drawing processes were investigated using X-ray diffraction （XRD） and electron back scatter diffraction （EBSD） techniques. The experimental results show that the 〈111〉 and 〈100〉 fibre textures are the main texture components, and crystalline grains in the surface are more fine and uniform than those in the center of Fe-Ni alloy wires during cold-drawing processes. It is found that the volume fraction of the 〈111〉 fibre texture component determined by quantitative regression calculation of the Gaussian distribution function reaches more than 60% and the strong 〈111〉 fibre texture component favors the torsional property of Fe-Ni alloy wires.

Effect of rolling temperature on microstructure and texture of twin roll cast ZK60 magnesium alloy

Twin roll cast ZK60 alloy strip/sheet with final thickness of 0.5 mm was prepared, and effect of rolling temperature on microstructure and texture development was investigated using OM and XRD technique, microstructure and texture were measured on specimens subjected to rolling experiment at different rolling temperature, and macrotexture was also evaluated by X-ray diffraction method. In addition, the （1010）and （0002） pole figures were measured, and the tensile test was performed to reveal the influence of rolling temperature on mechanical properties. The results show that the microstrucmre of ZK60 alloy sheet consisted of fibrous structure with elongated grains, and shear bands along the rolling direction after warm rolling. Dynamic recrystallization could be found during the warm rolling process at rolling temperature 350℃ and above. And many fine recrystallized grain could be observed in the shear bands area. It is a little difficult to see the recrystallized grain in the sheet warm rolled at 300℃ because of higher density of shear bands. The warm rolled ZK60 alloy sheet exhibited strong （0002） pole texture, the intensity of （0002） pole figure decreases with the increasing of rolling temperature and the basal pole tilted slightly to the transverse direction after warm rolling.

TEXTURAL REPRESENTATION FOR DEEP DRAWING STEEL SHEETS

Based on the crystallographic nature,two major characteristic textures of the deep drawing automobile body steel sheet are represented with inverse pole figures,The correlation between the textures of the deep drawing steel sheets and its deep drawing properties may be simply and directly analysed by the quantitative texture technique.The results obtained by this tech- nique is in agreement with that of ODF quantitative analysis.

Texture Analysis of Superconducting Films Based on YBCO System

Textures in different layers of superconductors based on YBCO system are analyzed using the methods of pole figure and con-ventional φ scans. It is shown that the φ scanning technology has only 1-dimensional description and could omit some information of3-dimensional orientaion distribution, which will influence the superconductor quality The pole figure method, in contrast, demonstra-tes the orientation distribution 2-dimensionally and gives a comprehensive view of thin filIn textUr, which is a much bettCr method fortexture analysis in superconducting films, in which there is commonly an unique high sharpness textur component.

Rolling Texture in Ti_3Al

The orientation changes and deformation behaviours of a Ti_3Al-based alloy was investigated by using micro-structure obervalion, pole figure and ODF analysis, as well as Chemical micro-analysis. A {0001} fibretexture an0d a weak {1210} <1010> texture were found after 35% cold rolling at room temlierature. The activation process of slip systems was discussed concerning formation of the rolling texture. Because of the low ductility of the material it is believed that the grains were deformed by simple glide suggested by Sachs.

The X-ray diffraction study of epitaxial La_(0.67)Sr_(0.33)MnO_(3）single crystal thin film

THE colossal magnetoresistance (CMR) effects in doped perovskite-like oxide have stimulatedconsiderable attention to the study of fundamental physics and the application of new type ma-terials. It was reported that a large CMR effect and a high critical temperature T_c shown