CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅰ.POLY(P-PHENYLENE TEREPHTHALATE)

The morphology and crytal structure of poly(p-phenylene terephthalate) (PPT), prepared by confined thin filmmelt (CTFMP) and solution (CTFSP) and bulk solution polymerization, were characterized by transmission electronmicroscopy, electron dimaction and molecular modeling. The unit cell is monoclinic (P2_1/a space group) with parameters a =7.89, b = 5.49, c = 12.65 A, α=γ= 90°, β=100.33°, density = 1.48 g/cm^3, the a, b and β values differing slightly from thosereported previously in the literature. A degree of variation in relative intensities of hk0 reflections in, apparently, untilted[001] ED patterns was observed from a given sample, suggesting some variation in molecular packing. ED evidence wasfound for a second phase, with [001] appearing the same as for phase Ⅱ of the related poly(p-oxybenzoate) (PpOBA)polymer. CTFMP crystals polymerized above 220℃ (up to 370℃) and CTFSP crystals polymerized at 300℃ consisted oflamellae 100-200 A thick.

CRYSTAL STRUCTURE AND MORPHOLOGY OF NASCENT SAMPLES OF SYMMETRIC AROMATIC POLYESTERS——Ⅱ. POLY(p-PHENYLENE 2,6-NAPHTHALATE)

Confined thin film melt polymerization (CTFMP) of naphthalene chloride/hydroquinone (NCMQ, 1/1, molar)mixtures at polymerization temperatures (T_p) below ca. 300℃ resulted in relatively thick, elongated crystals. Polymerizationof NC/HQ above 300℃ between glass yielded well-formed lamellar crystals ca. 100 A thick. Phase Ⅰ and Ⅱ [001] EDpatterns were obtained for all T_p, the relative amount of phase Ⅰ increasing with T_p. Polymerization of naphthalenedicarboxylic acid/hydroquinione diacetate 1/1 mixtures at high T_p also yielded lamellar crystals that "curled up" off of thesubstrate. When the high temperature CTFMP polymerization was conducted between mica, aggregates of lamellae on-edgedeveloped but epitaxial growth did not occur. Epitaxial growth of lamellae between mica could be obtained, however, byconfined thin film solution polymerization, with both of the latter samples yielding apparently related ED patterns from adifferent unit cell than phase Ⅰ or Ⅱ. Fiber patterns, obtained from sheared samples, indicated considerably greater crystaldisorder than in the nascent crystals. Refinement of the phase Ⅰ unit cell parameters, based on the [001] and [01 1] EDpatterns, with modeling based on Cerius^2, suggests a monoclinic phase Ⅰ unit cell with a = 7.76, b = 5.71, c = 14.99 A, α = γ= 90°, β= 99.7°, ρ = 1.47 g/cm^3, space group P12_1/al.

Mechanical Property and Crystal Structure of Poly(p-phenylene terephthalamide)(PPTA) Fibers during Heat Treatment under Tension

The relationship between property and structure of poly( p-phenylene terephthalamide)( PPTA) was investigated for the purpose of obtaining products with better performance. PPTA fiber subjected to heat treatment under different conditions was intensively studied. Simultaneous wide-angle X-ray diffraction( WAXD) technique was introduced to study the changes of crystal structure. It was found that the tensile modulus was strongly sensitive to the levels of temperature and tension. The structure parameters including crystal size and crystal orientation after heat treatment evolve similarly to the tensile modulus,indicating a direct structure-property relationship. The lattic c-dimension increases after heat treatment and is greatly affected by the tension. An optimal temperature can be found around 400 ℃,where big change can happen in the crystal structure due to α-relaxation in the crystal region as supported in dynamic mechanical analysis( DMA).

A STUDY OF PACKING STRUCTURE OF POLY(P-PHENYLENE BENZOBISTHIAZOLE)BY MOLECULAR SIMULATION

Molecular simulation technique was used in an examination of the possibilities of chain packing in the crystalline state for poly(ρ-phenylene benzobisthiazole).It has been found that one reason of hardly forming very ordered crystal of the polymer is the existence of so many stable positions of interchain interaction along chain axis.

The Synthesis and Electronic Characteristics of Poly(p-Phenylene Vinylene) Derivatives

A series of soluble poly(p-phenylene vinylene) (PPV) derivatives were synthesized through dehydrochlorination with the p-metaoxy phenol as starting materials. The electronic characteristics of PPV derivatives were studied.

Laser-induced Janus graphene/poly(p-phenylene benzobisoxazole)fabrics with intrinsic flame retardancy as flexible sensors and breathable electrodes for fire-fighting field

Conventional firefighting clothing and fire masks can protect firemen’s safety to a certain extent,whereas cannot perceive environmental hazards and monitor their physical status in real time.Herein,we fabricated two kinds of Janus graphene/poly(pphenylene benzobisoxazole)(PBO)fabrics by laser direct writing approach and evaluated their performance as intelligent firefighting clothes and fire masks.The results showed that the Janus graphene/PBO fabrics were virtually non-combustible and achieved the highest thermal protection time of 18.91 s ever reported in flame,which is due to the intrinsic flame-retardant nature of PBO fibers.The graphene/PBO woven fabrics-based sensor showed good repeatability and stability in human motion monitoring and NO_(2)gas detection.Furthermore,the piezoelectric fire mask was assembled with graphene/PBO nonwoven fabric as electrode layer and polyvinylidene fluoride(PVDF)electrostatic direct writing film as piezoelectric layer.The filtration efficiency of the fire mask reaches 95%for PM_(2.5)and 100%for PM_(3.0),indicating its effective filtration capability for smoke particles in fires.The respiratory resistance of the piezoelectric fire mask(46.8 Pa)was lower than that of commercial masks(49 Pa),showing that it has good wearing comfort.Besides,the piezoelectric fire mask can be sensitive to the speed and intensity of human breathing,which is essential for indirectly reflecting the health of the human body.Consequently,this work provides a facile approach to fabricate next-generation intrinsic flame-retardant smart textiles for smart firefighting.

Effect of Curing Poly(<i>p</i>-Phenylene Sulfide) on Thermal Properties and Crystalline Morphologies

Commercial poly(p-phenylene sulfide) (PPS) was thermally cured, which resulted in an increase of molecular weight due to cross-linking. Non-isothermal crystallization studies of samples cured for up to 7 days at 250?C showed a monotonous increase of crystallization temperature compared to pure PPS. However, a further increase of curing time decreased the crystallization temperature. The change in the half-crystallization time (t1/2) was similar to the crystallization temperature. Thus, the cross-linking of PPS affected crystallization behaviors significantly. To a certain extent, crosslinks acted as nucleation agents, but excessive cross-linking hindered the crystallization. Morphologies observed by polarized optical microscopy suggested that thermal curing for as little as 1 day contributed to the spherulitic structure having a smaller size, that was not observed with pure PPS.

STUDIES ON THE POLYPYRROLE/POLYELECTROLYTE MOLECULAR COMPOSITES

The potyelectrolyte of propane sulfonate(PS) grafted PPTA copolymers——PPTA-PS, PPTA[O]-PS, PPTA[C]-PS were prepared and used as electrolyte in the process of electrochemical polymerization of pyrrole to form the molecular composite polypyrrole (PPY)/Polyelectrolyte.The preparation and liquid crystalline property of three kinds of polyelectrolyte, the electrical conductivity, mechanical properties, SEM and thermoproperties of PPY/polyelectrolyte are presented in detail.

RAMAN SPECTROSCOPIC STUDY ON THE CHAIN CONFORMATION OF ELECTROSYNTHESIZED POLY(ρ-PHENYLENE)FILMS

Poly（p-phenylene） （PPP） films have been electrochemically deposited on mirrorlike stainless steel （SS） electrode surfaces by direct oxidation of benzene in boron trifluoride diethyl etherate （BFEE） solutions at a constant applied potential of 1.7 V （versus Ag/AgCl）. The chain conformations of as-grown PPP films have been studied by Raman spectroscopy. The results demonstrated that high synthesis temperature favors the formation of planar PPP, and the conformation of planar PPP can be changed into torsional PPP by cooling treatment.

CONFORMATION AND CHAIN PACKING STRUCTURES OF POLY (ρ-PHENYLEN BENZOBISTHIAZOLE) BY MOLECULAR SIMULATION

The conformation, the chain packing stabilization and the unit cell modeling of poly(p-phenylene benzobisthiazole) have been investigated by using molecular simulation techniquein the present work. A coupling behaviour of σ-bond rotations at either side of the pheny-lene ring or the heterocyclic ring was found surely to exceed a length of the repeat unit ofthe polymer chain. For a single chain model, the stable torsion angle of the repeat resultedat 14°. In the crystalline cell minimization, the dihedral angle along the polymer chaincould even be stabilized in various values. It therefore indicates that the intermolecularinteraction does play a considerable role for this polymer forming the conformation. Ac-cording to cohesive energies calculated for these unit cell models, the torsion angle in themost stable crystalline cell is 0°. When the chains packing together, there exist so manyenergy stable wells along the chain axis 0.35--0.36nm apart from neighbouring chains.Most of the unit cells have quite closed cohesive energies. These factors thus cause thedifficulty of forming an unique perfect crystalline structure of the polymer. The presentstudy suggested a number of reasonable unit cells, and the most stable crystalline structurefor this polymer that is monoclinic, non-primitive unit cell.

Non-aqueous Suspension Polycondensation in NMP-Ca Cl_2/Paraffin System―A New Approach for the Preparation of Poly(p-phenylene terephthalamide)

A non-aqueous suspension polycondensation method was proposed to proceed the reaction ofp-phenylenediamine and terephthaloyl chloride for the preparation of poly（p-phenylene terephthalamide） （PPTA）. The system was operated with NMP-CaCI2 solution as the dispersed phase and inert liquid paraffin as the continuous phase. Each of NMP-CaCl2 solution microdroplet suspended in paraffin served as a microreactor where the polycondensation took place. According to the results of TGA, XRD, IR, SEM and EA, PPTA with good quality was obtained through this novel method, and a number of main factors influencing this process were investigated to determine the optimum condition for the preparation of PPTA. Besides, this two-phase polycondensation system brings many unique advantages compared to the conventional solution polycondensation method, including a sealed reaction environment keeping the reactants away from oxygen and water, easy removal of HCI to promote the reaction, well-controlled temperature and low viscosity which means less energy cost.

High‑Temperature‑Tolerant Artificial Muscles Using Poly(p‑phenylene benzobisoxazole)Composite Yarns

Today the developed yarn muscles or actuators still cannot satisfy the requirements of working in high-temperature environ-ments.Thermal resistivity is highly needed in aerospace and industrial protection applications.Herein,an artificial muscle with high-temperature tolerance is prepared using carbon nanotube(CNT)wrapped poly(p-phenylene benzobisoxazole)(PBO)composite yarns.A thermal twisting method was utilized to reorientate the stiff PBO molecular chains into a uniform and twist-stable coiled structure.The CNT/PBO composite yarn muscle generates reversible contractile strokes up to 18.9%under 5.4 MPa tension and outputs 1.3 kJ kg^(-1) energy density.In contrast to previous actuators,which are normally oper-ated at room temperatures,the CNT/PBO composite yarn muscles can work at ambient temperatures up to 300℃ with high contractile stroke and long-term stability.A bionic inchworm robot,a deployable structure,and smart textiles driven by the high-temperature-tolerant yarn muscles were demonstrated,showing the promise as a soft actuator towards high-temperature environment applications.

Dispersion of multi-walled carbon nanotubes in poly(p-phenylene) thin films and their electrical characteristics

Dispersion of multi-walled carbon nanotubes in poly（p-phenylene） composite exposed to toluene was experimentally investigated. 3 mg of multi-walled carbon nanotubes with nominal size of 20 nm was compounded with 30 mg of poly（p-phenylene） with the presence of terpineol as binding initiator. To investigate an optimal condition for homogenizing all constituents, ultrasonication with an output power of 750W was employed with compounding time of 3, 10, 20 and 30 min. With FTIR analyses, it could be confirmed that homogeneous composite of multi-walled carbon nanotubes and poly（p-phenylene） could be prepared. SEM analyses were also conducted to examine the dispersion of multi-walled carbon nanotubes in the polymer matrix. Then intrinsic electrical resistance of the composites after being exposed to toluene was also investigated. It was found that the composite film prepared with ultrasonication for 20 min could provide sufficiently sensitive response with respect to varied concentration of toluene.

Kinetics Analysis on the Polycondensation Process of Poly(p-phenylene terephthalamide):Experimental Verification and Molecular Simulation

The conventional low-temperature method of solution polycondensation was developed to realize the reaction of p-phenylenediamin and terephthaloyl chloride for the preparation of poly（p-phenylene terephthalamide）（PPTA）. Some main factors influencing this process were investigated to determine the optimum condition for high molecular weight. Experiment showed significant slowing of the reaction and gradual deviation of second-order reaction kinetics due to diffusion control. These phenomena were studied theoretically via dynamic Monte Carlo simulation. A concise expression,n～c0^-0.88·t^0.37, was proposed to describe the diffusioncontrolled polycondensation process as a function of the monomer concentration and reaction time. The theoretical results provided a good description of diffusion-effected kinetics for the polycondensation process of PPTA, and demonstrated good agreement with the experimental data. Some differences of scaling relations between model and experiment results were also discussed.

PBO纤维的合成、纺制、微相结构与性能研究进展

PBO(聚对苯撑苯并双口恶唑)纤维是新一代超高性能纤维,文中对PBO纤维研制开发中关于合成、纺制、微相结构与性能方面的研究作一较详细的概述,特别阐述了其结构与性能关系研究的一些最新成果。

PBO纤维的性能及应用

介绍了聚对苯撑苯并双噁唑(PBO)纤维的结构特点、性能及应用。PBO纤维分子沿轴向高度取向,其强度和初始模量高,具有耐热、阻燃、耐冲击、耐弯曲疲劳和耐化学稳定性等优良性能。PBO纤维在耐热材料、增强材料、防弹抗冲击材料以及航空领域与军事领域广泛应用。

液晶高分子聚苯撑苯并二噁唑的合成、结构与性能

本文以间苯二酚为原料,合成了缩聚单体4,6-二胺基1,3-间苯二酚盐酸盐。在多聚磷酸介质中与对苯二甲酸经分段升温缩聚得聚苯撑苯并二噁唑(PBZO).用元素分析法,X-光衍射法、X-光平板照相、FTIR和C^(13)-NMR研究了PBZO的结构.测定了PBZO/MSA体系的特性粘数。测定了PBZO的力学性能和热稳定性。结果表明PBZO是继PBZT后又一种新型的高性能液晶高分子材料。

聚苯撑苯并二噁唑(PBO)的合成

分别由对苯二甲酸(TPA)、对苯二甲酰氯(TPC)和4,6-二氨基间苯二酚盐酸盐(DAR)聚合得到了[η]=15.2、10.4 dL/g的PBO聚合物,对聚合物进行了红外光谱及元素分析,用透射电镜观察了聚合物膜的形态,同时比较了两种聚合体系对聚合反应的影响。

超级纤维PBO的性能应用及研究进展

在系统介绍 2 1世纪超级纤维及工业新材料 PBO(聚对苯撑苯并二唑 )的优异性能与应用领域的基础上 ,重点叙述了经新单体 4,6-二氨基间苯二酚盐酸盐与对苯二甲酸及其衍生物进行缩合共聚制备 PBO基体 ,进而加工成纤维等技术研究的起源和发展 ,以及当今美国 Dow化学公司、日本 Toyobo公司和 Nissan化学公司等专利技术的进展 ,同时针对存在的问题预测了 PBO的发展趋势 ,建议性地提出了国内急需发展 PBO研究的目标、内容及今后的方向 :即提高新单体的纯度和稳定性、降低成本是 PBO技术研究中首要解决的实际问题 ,而不同的聚合方式、缩聚新技术及单体合成的新方法则是今后十年内 PBO材料进一步研究的新内容。