SYNTHESIS AND CHARACTERIZATION OF POLYROTAXANES MADE FROM α-CDs THREADED ONTO TRIBLOCK COPOLYMERS WITH PEG AS A CENTRAL AXLE AND FLANKED BY TWO LOW MOLECULAR WEIGHT POLYSTYRENES AS OUTER STOPPERS

A study has been conducted on the synthesis and characterization of a kind of novel polyrotaxanes comprisingα- cyclodextrins (α-CDs) threaded on triblock eopolymers with poly(ethylene glycol) (PEG) as a central axle and flanked by two low molecular weight polystyrenes as outer stoppers.Styrene was allowed to telomerize with polypseudorotaxanes as chain transfer agents made from the self-assembly of a distal thiol-capped PEG with a varying amount ofα-CDs in the presence of a redox initiation system at 40~C i...

Lateral earth pressure of granular backfills on retaining walls with expanded polystyrene geofoam inclusions under limited surcharge loading

Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.

Recent progress and future directions of the research on nanoplastic-induced neurotoxicity

Many types of plastic products,including polystyrene,have long been used in commercial and industrial applications.Microplastics and nanoplastics,plastic particles derived from these plastic products,are emerging as environmental pollutants that can pose health risks to a wide variety of living organisms,including humans.However,it is not well understood how microplastics and nanoplastics affect cellular functions and induce stress responses.Humans can be exposed to polystyrene-microplastics and polystyrene-nanoplastics through ingestion,inhalation,or skin contact.Most ingested plastics are excreted from the body,but inhaled plastics may accumulate in the lungs and can even reach the brain via the nose-to-brain route.Small-sized polystyrene-nanoplastics can enter cells by endocytosis,accumulate in the cytoplasm,and cause various cellular stresses,such as inflammation with increased pro-inflammatory cytokine production,oxidative stress with generation of reactive oxygen species,and mitochondrial dysfunction.They induce autophagy activation and autophagosome formation,but autophagic flux may be impaired due to lysosomal dysfunction.Unless permanently exposed to polystyrene-nanoplastics,they can be removed from cells by exocytosis and subsequently restore cellular function.However,neurons are very susceptible to this type of stress,thus even acute exposure can lead to neurodegeneration without recovery.This review focuses specifically on recent advances in research on polystyrene-nanoplastic-induced cytotoxicity and neurotoxicity.Furthermore,in this review,based on mechanistic studies of polystyrene-nanoplastics at the cellular level other than neurons,future directions for overcoming the negative effects of polystyrene-nanoplastics on neurons were suggested.

Performance Evaluation of Novel Eco-Materials Composed of Millet Husks, Rice Husks, and Polystyrene

Managing agricultural waste and expanded polystyrene (EPS) poses significant environmental and economic challenges. This study aims to create composites from millet husks, rice husks, and recycled EPS, using a manufacturing method that involves dissolving the polystyrene in a solvent followed by cold pressing. Various particle sizes and two binder dosages were investigated to assess their influence on the physico-mechanical properties of the composites. The mechanical properties obtained range from 2.54 to 4.47 MPa for the Modulus of Rupture (MOR) and from 686 to 1400 MPa for the Modulus of Elasticity in Bending (MOE). The results indicate that these composites have potential for applications in the construction sector, particularly for wood structures and interior decoration. Moreover, surface treatments could enhance their durability and mechanical properties. This research contributes to the valorization of agricultural and plastic waste as eco-friendly and economical construction materials.

Study of the Conversion of Postconsumer Polystyrene on CeO2/HZSM-5 Type Materials

The catalytic conversion of polystyrene (PS) was studied in the presence of the materials type HZSM-5, CeO2, 10% CeO2/HZSM-5 and 20% CeO2/HZSM-5, which were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and nitrogen adsorption at 77K. The catalytic tests were performed via thermogravimetric analysis (TG) at heating rates of 5, 10 and 20˚C min−1 in a temperature range from 30˚C to 900˚C. For the tests, a ratio of 30% by mass of each catalytic material mixed with PS was used and the activation energy of the degradation process was determined by the Vyazovkin method. The obtained results showed that the addition of the catalyst to the PS in general reduced its degradation temperature. The 10% CeO2/HZSM-5 catalyst showed greater efficiency, as it resulted in lower activation energy for PS degradation. Thus, the combination of CeO2 with HZSM-5 resulted in materials with potential for application in the catalytic degradation of polystyrene and the results indicate that the production of a composite material can be a good strategy to generate an increase in catalytic activity and a decrease in energy process activation.

Fabrication of fire-retardant building materials via a hyper-crosslinking chemical conversion process from waste polystyrenes

Polystyrene(PS)is rich in plastic materials,but it produces a large amount of waste every year,causing a huge burden on the environment.Although PS plastic is the source of a common"white pollution"in daily life,it still has a high utilization value.At the same time,the flammability of PS material determines that it cannot be applicated in places where fire accidents occur frequently.As a result,its application has been greatly limited.In order to realize the efficient utilization of waste PS and broaden its scope of application,PS was modified by hyper-crosslinking in order to improve its fire-retardant performance.In this method,the PS solution with high purity was obtained by dissolving waste PS foam with 1,2-dichloroethane(DCE),and then the hyper-crosslinked polymer with high specific surface area was prepared by adding cross-linking agent formaldehyde dimethyl acetal(FDA)and a Lewis-acid catalyst ferric chloride(FeCl_(3)).Further studies showed that the effects of the amount of cross-linking agent FDA,catalyst FeCl_(3) and PS on the reaction products were different.In addition,compared the as-prepared fire-retardant materials with PS foam from the aspects of flame retardancy and thermal insulation,it can be concluded that the fire-retardant performance of the materials prepared by this method has been significantly enhanced.And it is proved that this method is feasible towards the preparation of a large number of fire-retardant composite materials by using a scale-up experiment.

An energetic nano-fiber composite based on polystyrene and 1,3,5-trinitro-1,3,5-triazinane fabricated via electrospinning technique

Electrospinning is a simple technique used to fabricate polymeric nano-fibrous membranes.These nano-fibers have found a wide range of valuable applications in the biomedical field.However,it has not been utilized with solid high explosives yet.Herein,the electrospinning technique has been used to fabricate polystyrene(PS)/1,3,5-trinitro-1,3,5-triazinane(RDX)composite nanofibers.The governed electrospinning parameters,voltage,distance from the collector,flow rate,mandrel rotating speed,time,and solution concentration,that greatly affect the morphology of the obtained nanofibers were optimized.The fabricated PS/RDX nano-fibers were characterized using scanning electron microscopy(SEM),X-ray diffractometer(XRD),and Fourier Transform Infrared(FTIR)spectroscopy.The impact and friction sensitivities of PS/RDX were also measured.The thermal behavior of the prepared composite and the pure materials were studied by the thermal gravimetric analysis technique(TGA).SEM results proved the fabrication of PS/RDX fibers in the nano-size via electrospinning.FTIR spectroscopy confirmed the existence of the characteristic functional groups of both PS and RDX in the composite nano-fibers.XRD sharp peaks showed the conversion of amorphous PS into crystalline shape via electrospinning and also confirmed the formation of PS/RDX composite.The PS fibers absorbed the heat and increased the onset decomposition of the pure RDX from 181.5 to 200.7℃in the case of PS/RDX fibers.Interestingly,PS/RDX nano-fibers showed the relatively low impact and friction sensitivities of 100 J and 360 N respectively.These results could introduce PS/RDX nanofibrous composite in the field of explosives detection with high levels of safety.

Comprehensive analysis of sodium polystyrene sulfonate-induced colitis:A systematic review

BACKGROUND Sodium polystyrene sulfonate(SPS)is commonly prescribed for the management of hyperkalemia,a critical electrolyte imbalance contributing to over 800000 annual visits to emergency departments.AIM To conduct a systematic review of documented cases of SPS-induced colitis and assess its associated prognosis.METHODS Following the PRISMA-P guidelines,our study employed Medical Subject Headings and Health Sciences Descriptors,skillfully combined using Boolean operators,to conduct comprehensive searches across various electronic databases,including Scopus,Web of Science,MEDLINE(PubMed),BIREME(Biblioteca Regional de Medicina),LILACS(Latin American and Caribbean Health Sciences Literature),SciELO(Scientific Electronic Library Online),Embase,and Opengray.eu.Language criteria were confined to English,Spanish,and Portuguese,with no limitations on the publication date.Additionally,we manually scrutinized the reference lists of retrieved studies.To present our findings,we utilized simple descriptive analysis.RESULTS Our search strategy yielded a total of 442 references.After rigorous evaluation,we included 51 references,encompassing 59 documented cases of colitis.Predominant clinical presentations included abdominal pain,observed in 35(60.3%)cases,and bloating,reported in 18(31%)cases.The most frequently affected sites of inflammation were the cecum,rectum,and small intestine,accounting for 31%,25.8%,and 22.4%of cases,respectively.Colonoscopy findings were described in 28(48.2%)cases,and 29(50%)of patients required surgical intervention.Among the subset of patients for whom outcome data was available,39(67.2%)experienced favorable outcomes,while 12(20.6%)unfortunately succumbed to the condition.The mean time required for resolution was 36.7 d,with a range spanning from 1 to 120 d.CONCLUSION SPS demonstrates the capacity to effectively lower serum potassium levels within 24 h.However,this benefit is not without the risk of bowel injury.Our study highlights the absence of high-quality data pertaining to the incidence of adverse events associated with SPS usage,making it challenging to determine whether the potential risks outweigh the benefits.However,a significant mortality rate related to SPS-induced colitis was noted.Future investigations should prioritize randomized controlled trials with a sufficiently large patient cohort to ascertain the true utility and safety profile of this medication.

Thermal Decomposition and a Kinetic Study of Poly(Para-Substituted Styrene)s

The thermal decompositions of polystyrene (PS), poly(p-methyl styrene) (PMS), poly(p-bromo styrene) (PBrS), and poly(p-chloro styrene) (PClS) were investigated through thermogravimetric analysis (TGA). For this aim, Flynn-Wall-Ozawa method was applied to derivative thermogravimetric (DTG) curves. Continuous distribution kinetics was employed with a stoichiometric kernel to determine the rate coefficients for decomposition reactions. TGA data for the polymers were investigated by nonlinear fitting procedures that yielded activation energies and frequency factors for the combined chemical reactions. The reaction order values of PS derivatives are just about 1 in the nonisothermal decomposition process. Ea values for PS, PMS, and PClS increase with % conversion individually as they decrease in the order of PS/PMS/PClS which is consistent with the molecular weight increase. On the other hand, PBrS has the highest activation energy. Also its activation energy decreases with the % conversion. Thus it is suggested that PBrS degrades with somehow different mechanism.

Leaching of styrene and other aromatic compounds in drinking water from PS bottles

Bottled water may not be safer, or healthier, than tap water. The present studies have proved that styrene and some other aromatic compounds leach continuously from polystyrene （PS） bottles used locally for packaging. Water sapmles in contact with PS were extracted by a preconcentration technique called as ＂purge and trap＂ and analysed by gas chromatograph-mass spectrometer （GC/MS）. Eleven aromatic compounds were identified in these studies. Maximum concentration of styrene in PS bottles was 29.5 μg/L. Apart from styrene, ethyl benzene, toluene and benzene were also quantified but their concentrations were much less than WHO guide line values. All other compounds were in traces. Quality of plastic and storage time were the major factor in leaching of styrene. Concentration of styrene was increased to 69.53 μg/L after one-year storage. In Styrofoam and PS cups studies, hot water was found to be contaminated with styrene and other aromatic compounds. It was observed that temperature played a major role in the leaching of styrene monomer from Styrofoam cups. Paper cups were found to be safe for hot drinks.

Anti Cervix Cancer Activity of Co-immobilized Tumor Necrosis Factor-α and Interferon-γ

Tumor necrosis factor α （TNF-α） and interferon-γ （IFN-γ） are cytokines with strong antitumor activities. They were reacted with a photoactive arylazide-4-azidobenzoic acid, resulting in photoactive TNF-α and IFN-γ. The infrared （IR） spectra of these products showed the characteristic absorption of an azido group at 2127 cm^-1. By photo-immobilization, this modified TNF-α and IFN-γ were immobilized on polystyrene membranes for cell culture to prepare biomaterials. The micro-morphology of photoactive cytokines was observed with a scanning electron microscope （SEM）. The inhibitory effect on growth of Hela cells and inducing apoptosis activity of these two cytokines were analyzed by growth curve, transmission electron microscope （TEM） and fluorescence active cell sorter （FACS）. The results showed that co-immobilization of IFN-γ and TNF-α had significant inhibitory effect on growth of Hela cells, inhibitory rate up to 82%, and IFN-γ had obviously synergistic action.

Effects of process parameters on dimensional precision and tensile strength of wax patterns for investment casting by selective laser sintering

Turbine blades, produced by the directional solidification(DS) process, often require high dimensional accuracy and excellent mechanical properties. A critical step in their production is the fabrication of wax patterns. However, the traditional manufacturing process has many disadvantages, such as long-term production, low material utilization rate, and the high cost of producing a complex-shaped wax pattern. Selective laser sintering(SLS) is one of the most extensively used additive manufacturing techniques that substantially shortens the production cycle. In this study, SLS was adopted to fabricate the wax pattern instead of the traditional manufacturing process. The orthogonal experiment method was carried out to investigate the effects of laser power, scanning speed, scanning space, and layer thickness on the dimensional precision and morphologies of the SLS parts. The SLS parts showed a minimum dimensional deviation when laser power, scanning speed, scanning space, and layer thickness were 10 W, 3000 mm·s-1, 0.18 mm, and 0.25 mm, respectively. In addition, the tensile strength and fracture morphologies were closely associated with the laser volumetric energy density(VED). The tensile strength reached a maximum when the VED was 0.0762 J·mm-3, with an evident brittle fracture morphology. The wax pattern manufactured in this way meets the accuracy and strength requirements for investment casting. This research offers a novel path for the production of wax patterns for complex-shaped turbine blades by SLS.

HALOMETHYLATION OF POLYSTYRENE AND SUBSEQUENT PYRIDINATION VIA A HOMOLYTIC PATHWAY

Chloromethylation of polystyrene （PS） with two different chloromethylating systems methylal/thionyl chloride and paraformaldehyde/trimethylchlorosilane was studied. Soluble chloromethylated polystyrene with a degree of substitution of 89% was obtained. The Conant-Finkelstein reaction on the chloromethylated PS afforded soluble iodomethylated polystyrene with a degree of substitution as high as 96%. The reaction conditions of Minisci were employed to radically pyridinate PS via its iodomethylated derivative. Polyelectrolytes were formed which could be converted to normal polymers by treatment with a 20% aqueous solution of NaOH.

Weatherability Studies on External Insulation Thermal System of Expanded Polystyrene Board,Polystyrene Granule and Polyurethane Foam

Atmospheric exposure tests including two experimental stages of high temperature-spraying water cycle and heating-refrigeration cycle were carried out on three currently used ETIS of expanded polystyrene（EPS） board,polystyrene granule mortar and polyurethane foam in order to study the weatherablility of external thermal insulation system（ETIS）.The change rules of adhesive strength were hereby studied at different time period of atmospheric exposure tests.The experimental results show that the adhesive strength of three kinds of ETIS changes a little during high temperature-spraying water cycle,but the adhesive strength of ETIS with EPS board decreases significantly after heating-refrigeration cycle.The lowering rate of adhesive strength with painting finishes is obviously faster than that of tile finishes for ETIS of EPS board during heating-refrigeration cycle.The weatherability of ETIS with EPS board is worse than the other two,and ETIS of polystyrene granule mortar and polyurethane foam are more suitable than ETIS of EPS board in cold area.

Morphology and Mechanical Properties of PS/Al_2O_3 Nanocomposites Based on Selective Laser Sintering

Selective laser sintering （SLS） is a new process to prepare the polystyrene （PS）/Al2O3 nanocomposites. In this paper, with different laser power and other processing parameters unchanged, the morphology, density and mechanical properties of the sintered specimens were investigated. It was found that nano-sized inorganic particles are uniformly located in the PS matrix and the maximum density of the sintered specimens with pure PS powder reaches 1.07 g/cm^3, higher than 1.04 g/cm^3 that of the sintered specimens with mixture powder. Due to strengthening and toughness of the nano-sized Al2O3 inorganic particles, the maximum notched impact strength and tensile strength of the sintered part mixed with nano-sized inorganic particles are improved greatly from 7.5 to 12.1 kJ/m^2 and from 6.5 to 31.2 MPa, respectively, under the same sintering condition.

A review of recent progress in preparation of hollow polymer microspheres

The preparation methods of hollow polymer microspheres both at home and abroad are summarized, and their preparation mechanisms and developmental states are presented. These methods include the liquid droplet method, dried-gel droplet method, self-assembly method, microencapsulation method, emulsion polymerization method and the template method. Hollow polystyrene microspheres are the most extensively studied in the research of hollow polymer microspheres. Through comparison of the advantages and disadvantages of different preparation methods, it is concluded that microencapsulation method is most suitable for preparing polystyrene hollow microspheres.

VAPOR-LIQUID EQUILIBRIA FOR MIXTURES OF TOLUENE AND POLYSTYRENE WITH DIFFERENT MOLECULAR WEIGHTS

An experimental system for measuring the VLE of polymer solutions based on the staticvapor-pressure method has been established,VLE data for mixtures of toluene and polystyrene withdifferent molecular weight covering a wide range from 2.98×10~3 to 3.84×10~6 were obtained at 35℃.The reduced pressure p/p°versus weight fraction W plot is found to be independent on the molecularweight of the polymer within the experimental error.Calculated activity coefficients are also independenton the molecular weight.However,for the Flory-Huggins interaction parameter x,not only a strongconcentration dependence is observed,but also the molecular weight of the polymer exerts definiteinfluence.Generally,the parameter x slightly increases as the molecular weight of the polymer decreasesespecially when the molecular weight is low.The dependence of the parameter x on the molecularweight can be neglected when the molecular weight of polymer is greater than 1.00×10~4.

Fabrication of Large-area 3-D Ordered Silvercoated Colloidal Crystals and Macroporous Silver Films Using Polystyrene Templates

The highly ordered silver-coated colloidal crystals arrays and macroporous silver films were derived through an electrostatics-induced adsorption effect using polystyrene(PS) as templates. Carboxyl-modified PS microspheres were prepared by emulsifier-free emulsion polymerization using methacrylic acid(MAA) as the functional monomer. PS microspheres were self-assembled into close packing colloidal crystals of facecentered cubic arrays to the substrate with vertical deposition method. These colloidal crystals were modified using dopamine(DA) to form poly-dopamine(PDA) during its oxidative polymerization. Through electrostatic interaction, the silver nanoparticles were deposited and adsorbed onto the surfaces of colloidal crystals templates by exposing [Ag(NH_3)_2]^+solution to infrared irradiation. Removal of the polymeric template by etching with methylbenzene solvent resulted in 3D ordered macroporous silver films. The structural and properties of the ordered silver-coated arrays and macroporous silver films were characterized by field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), UV-vis spectroscopy and surface-enhanced Raman spectroscopy(SERS). The results indicate that the prepared silver-coated arrays and macroporous silver films possess the features of ordered multilayer arrangement, uniformity and repeatability as well as an ideal SERS effect.

Fabrication of Fluorescent Porphyrin/Polystyrene Composite Nanospheres by Electrospinning

Fluorescent polystyrene（PS）/porphyrin（TPPA） composite nanospheres were successfully fabricated by electrospinning. The SEM images clearly show that owing to adding TPPA in PS, the averaged diameter of the composite nanospheres became smaller, from 1500 to 580 nm. Fourier-transform infrared（FTIR） spectra determined the chemical composition of the resulting PS/TPPA composite nanospheres. The photoluminescent（PL） spectral analysis indicates that the peak position of the composite nanospheres in either solid state or water is identical to that of pure TPPA, at about 652 nm, and is still unchangeable when they are left for at least 20 d, indicating the stable photoluminescent property of the fluorescent composite nanospheres.

Adsorption mechanism of phenolic compounds from aqueous solution on hypercrosslinked polymeric adsorbent

The adsorption of two phenols, namely, phenol and salicylic acid(SA) onto a water-compatible hypercrosslinked polymeric resin(NJ-8) were studied in terms of pseudo-second-order and first order mechanisms for chemical sorption as well as an intraparticle diffusion mechanism process. Kinetic analysis showed that the intraparticle diffusion process was the essential rate-controlling step. The activation energies of sorption have also been evaluated with the pseudo-second-order and intraparticle diffusion constants, respectively. Adsorption equilibrium data were well fitted by the Langmuir, Freundlich and Redlich-Peterson isotherms. Adsorption was exothermic and basically of a type of transition between physical and chemical character. The sorption capacity was higher for SA due to its more hydrophobic. Phenol has a higher adsorption enthalpy since it could form stronger hydrogen bonding on NJ-8.