Evolution of the porous structure for phosphoric acid etching carbon as cathodes in Li–O_(2) batteries:Pyrolysis temperature-induced characteristics changes

Although biomass-derived carbon(biochar)has been widely used in the energy field,the relation between the carbonization condition and the physical/chemical property of the product remains elusive.Here,we revealed the carbonization condition's effect on the morphology,surface property,and electrochemical performance of the obtained carbon.An open slit pore structure with shower-puff-like nanoparticles can be obtained by finely tuning the carbonization temperature,and its unique pore structure and surface properties enable the Li–O_(2) battery with cycling longevity(221 cycles with 99.8%Coulombic efficiency at 0.2 mA cm^(−2) and controlled discharge–charge depths of 500 mAh g^(−1))and high capacity(16,334 mAh g^(−1) at 0.02 mA cm^(−2)).This work provides a greater understanding of the mechanism of the biochar carbonization procedure under various pyrolysis conditions,paving the way for future study of energy storage devices.

A study on the temperature sensitivity of NMR porosity in porous media based on the intensity of magnetization Dedicated to the special issue “Magnetic Resonance in Porous Media”

The measurement of nuclear magnetic resonance(NMR)porosity is affected by temperature.Without considering the impact of NMR logging tools,this phenomenon is mainly caused by variations in magnetization intensity of the measured system due to temperature fluctuations and difference between the temperature of the porous medium and calibration sample.In this study,the effect of temperature was explained based on the thermodynamic theory,and the rules of NMR porosity responses to temperature changes were identified through core physics experiments.In addition,a method for correcting the influence of temperature on NMR porosity measurement was proposed,and the possible factors that may affect its application were also discussed.

Three-Dimensional Convection in an Inclined Porous Layer Subjected to a Vertical Temperature Gradient

In this paper,we study the onset and development of three-dimensional convection in a tilted porous layer saturated with a liquid.The layer is subjected to a gravitational field and a strictly vertical temperature gradient.Typically,problems of thermal convection in tilted porous media saturated with a liquid are studied by assuming constant different temperatures at the boundaries of the layer,which prevent these systems from supporting conductive(non-convective)states.The boundary conditions considered in the present work allow a conductive state and are representative of typical geological applications.In an earlier work,we carried out a linear stability analysis of the conductive state.It was shown that at any layer tilt angles,the most dangerous type of disturbances are longitudinal rolls.Moreover,a non-zero velocity component exists in z-direction.In the present work,threedimensional non-linear convection regimes are studied.The original three-dimensional problem is reduced to two-dimensional one with an analytical expression for the velocity z-component v_(z)=v_(z)(x,y).It is shown that the critical Rayleigh number values obtained through numerical solutions of the obtained 2D problem by a finite difference method for different layer inclination angles,are in a good agreement with those predicted by the linear theory.The number of convective rolls realized in nonlinear calculations also fits the linear theory predictions for a given cavity geometry.Calculations carried out at low supercriticalities show that a direct bifurcation takes place.With increasing supercriticality,no transitions to other convective regimes are detected.The situation studied in this problem can be observed in oil-bearing rock formations under the influence of a geothermal temperature gradient,where the ensuing fluid convection can affect the distribution of oil throughout the layer.

Preparation of porous semi-IPN temperature-sensitive hydrogel-supported nZVI and its application in the reduction of nitrophenol

Nanoscale zero-valent iron(n ZVI) particles supported on a porous, semi-interpenetrating(semi-IPN), temperature-sensitive composite hydrogel(PNIPAm-PHEMA). n ZVI@PNIPAmPHEMA, was successfully synthesized and characterized by FT-IR, SEM, EDS, XRD and the weighing method. The loading of nZVI was 0.1548 ± 0.0015 g/g and the particle size was30–100 nm. NZVI was uniformly dispersed on the pore walls inside the PNIPAm-PHEMA.Because of the well-dispersed n ZVI, the highly porous structure, and the synergistic effect of PNIPAm-PHEMA, nZVI@PNIPAm-PHEMA showed excellent reductive activity and wide p H applicability. 95% of 4-NP in 100 m L of 400 mg/L 4-NP solution with initial p H 3.0–9.0 could be completely reduced into 4-AP by about 0.0548 g of fresh supported n ZVI at 18–25 °C under stirring(110 r/min) within 45 min reaction time. A greater than 99% 4-NP degradation ratio was obtained when the initial p H was 5.0–9.0. The reduction of 4-NP by nZVI@PNIPAm-PHEMA was in agreement with the pseudo-first-order kinetics model with Kobsvalues of 0.0885–0.101 min-1.NZVI@PNIPAm-PHEMA was able to be recycled, and about 85% degradation ratio of 4-NP was obtained after its sixth reuse cycle. According to the temperature sensitivity of PNIPAmPHEMA, n ZVI@PNIPAm-PHEMA exhibited very good storage stability, and about 88.9%degradation ratio of 4-NP was obtained after its storage for 30 days. The hybrid reducer was highly efficient for the reduction of 2-NP, 3-NP, 2-chloro-4-nitrophenol and 2-chloro-4-nitrophenol. Our results suggest that PNIPAm-PHEMA could be a good potential carrier, with n ZVI@PNIPAm-PHEMA having potential value in the application of reductive degradation of nitrophenol pollutants.

Low temperature molten salt synthesis of porous La_(1-x)Sr_xMn_(0.8)Fe_(0.2)O_3(0≤x≤0.6) microspheres with high catalytic activity for CO oxidation

A molten salt method was developed to prepare porous La1‐xSrxMn0.8Fe0.2O3 （0≤ x ≤ 0.6） micro‐spheres using hierarchical porous δ‐MnO2 microspheres as a template in eutectic NaNO3‐KNO3. X‐ray diffraction patterns showed that single phase LaMn0.8Fe0.2O3 with good crystallinity was syn‐thesized at 450℃ after 4 h. Transmission electron microscope images exhibited that the LaMn0.8Fe0.2O3 sample obtained at 450？？ after 4 h possessed a porous spherical morphology com‐posed of aggregated nanocrystallites. Field emission scanning electron microscope images indicated that the growth of the porous LaMn0.8Fe0.2O3 microspheres has two stages. SEM pictures showed that a higher calcination temperature than 450？？ had an adverse effect on the formation of a po‐rous spherical structure. The LaMn0.8Fe0.2O3 sample obtained at 450？？ after 4 h displayed a high BET surface area of 55.73 m2/g with a pore size of 9.38 nm. Fourier transform infrared spectra suggested that Sr2＋ions entered the A sites and induced a decrease of the binding energy between Mn and O. The CO conversion with the La1‐xSrxMn0.8Fe0.2O3 （0≤x≤0.6） samples indicated that the La0.4Sr0.6Mn0.8Fe0.2O3 sample had the best catalytic activity and stability. Further analysis by X‐ray photoelectron spectroscopy demonstrated that Sr2＋doping altered the content of Mn4＋ions, oxygen vacancies and adsorbed oxygen species on the surface, which affected the catalytic performance for CO oxidation.

Radiation Effect on Natural Convection Near a Vertical Plate Embedded in Porous Medium with Ramped Wall Temperature

Radiation effect on the natural convection flow of an optically thin viscous incompressible fluid near a vertical plate with ramped wall temperature in a porous medium has been studied. The exact solution of momentum and energy equations is obtained by the use of Laplace transform technique. The variations in fluid velocity and temperature are shown graphically whereas the numerical values of shear stress and the rate of heat transfer at the wall are presented in tabular form for various values of flow parameters. The results show that the fluid velocity increases with increase in Grashof number, Darcy number and time parameters whereas the fluid velocity decreases with increase in the radiation parameter and Prandtl number for ramped temperature as well as isothermal wall temperature. It is found that an increase in radiation parameter leads to rise the temperature for both ramped wall temperature as well as isothermal wall temperature. Further, it is found that an increase in Prandtl number leads to fall the temperature for both ramped wall temperature as well as isothermal wall temperature. The shear stress at the wall decreases with increases in either Prandtl number or porosity parameter while the result shows reverse in the case of radiation parameter. Finally, the rate of heat transfer is increased with increases in the radiation parameter for both ramped wall temperature as well as isothermal wall temperature.

Regulating adsorption ability toward polysulfides in a porous carbon/Cu_(3)P hybrid for an ultrastable high-temperature lithium-sulfur battery

Lithium-sulfur batteries(LSBs)can work at high temperatures,but they suffer from poor cycle life stability due to the“shuttle effect”of polysulfides.In this study,pollen-derived porous carbon/cuprous phosphide(PC/Cu_(3)P)hybrids were rationally synthesized using a one-step carbonization method using pollen as the source material,acting as the sulfur host for LSBs.In the hybrid,polar Cu_(3)P can markedly inhibit the“shuttle effect”by regulating the adsorption ability toward polysulfides,as confirmed by theoretical calculations and experimental tests.As an example,the camellia pollen porous carbon(CPC)/Cu_(3)P/S electrode shows a high capacity of 1205.6 mAh g^(−1) at 0.1 C,an ultralow capacity decay rate of 0.038%per cycle after 1000 cycles at 1 C,and a rather high initial Coulombic efficiency of 98.5%.The CPC/Cu_(3)P LSBs can work well at high temperatures,having a high capacity of 545.9 mAh g^(−1) at 1 C even at 150℃.The strategy of the PC/Cu_(3)P hybrid proposed in this study is expected to be an ideal cathode for ultrastable high-temperature LSBs.We believe that this strategy is universal and worthy of in-depth development for the next generation energy storage devices.

Migration Effect of Temperature on Formaldehyde in Porous Building Materials

A coupled heat and formaldehyde migration model based on the non-equilibrium thermodynamic theory and molecule movement theory was developed.The effect of temperature on the transport coefficients was simulated,and the simulation results were validated with experimental data from the literatures.The calculation shows that air exchange rate larger than 2 h-1 should be prevented,if the purpose is only for formaldehyde emissions control.The effects of temperature on formaldehyde migration are obvious.

CONJUGATE MODEL FOR HEAT AND MASS TRANSFER OF POROUS WALL IN THE HIGH TEMPERATURE GAS FLOW

Heat and mass transfer of a porous permeable wall in a high temperature gas dynamical flow is considered. Numerical simulation is conducted on the ground of the conjugate mathematical model which includes filtration and heat transfer equations in a porous body and boundary layer equations on its surface. Such an approach enables one to take into account complex interaction between heat and mass transfer in the gasdynamical flow and in the structure subjected to this flow. The main attention is given to the impact of the intraporous heat transfer intensity on the transpiration cooling efficiency.

Quasi-static and low-velocity impact mechanical behaviors of entangled porous metallic wire material under different temperatures

To improve the defense capability of military equipment under extreme conditions,impact-resistant and high-energy-consuming materials have to be developed.The damping characteristic of entangled porous metallic wire materials(EPMWM)for vibration isolation was previously investigated.In this paper,a study focusing on the impact-resistance of EPMWM with the consideration of ambient temperature is presented.The quasi-static and low-velocity impact mechanical behavior of EPMWM under different temperatures(25℃-300℃)are systematically studied.The results of the static compression test show that the damping energy dissipation of EPMWM increases with temperature while the nonlinear damping characteristics are gradually enhanced.During the impact experiments,the impact energy loss rate of EPMWM was between 65%and 85%,while the temperatures increased from 25℃to 300℃.Moreover,under the same drop impact conditions,the overall deformation of EPMWM decreases in the temperature range of 100℃-200℃.On the other hand,the impact stiffness,energy dissipation,and impact loss factor of EPMWM significantly increase with temperature.This can be attributed to an increase in temperature,which changes the thermal expansion coefficient and contact state of the internal wire helixes.Consequently,the energy dissipation mode(dry friction,air damping,and plastic deformation)of EPMWM is also altered.Therefore,the EPMWM may act as a potential candidate material for superior energy absorption applications.

An experimental study of temperature and moisture content of wet porous materials under short-pulsed laser heating

The measurements of temperature and moisture content of a wet porous material were accomplished on the micro-seconds scale. The temperature wave was observed when the wet porous material was heated by short-pulsed laser with high power. It firstly revealed that the moisture content of wet porous material rapidly rises twice in one laser irradiation. The influences of laser parameters, the thickness and initial moisture content of the wet porous material on its temperature and moisture content were investigated.

Porous Ultra-high Temperature Ceramics for Ultra-high Temperature Thermal Protection System

Ultra-high temperature ceramics(UHTCs)are a family of borides,carbides and nitrides of transition elements such as hafnium,zirconium,tantalum and niobium.They exhibit the highest known melting points,good mechanical strength,good chemical and thermal stability under certain conditions.In last decade,researchers dedicated to characterize porous UHTCs aiming to develop novel thermal insulating materials that could withstand temperatures over 2000℃.In this article,the preparation and characteristics of porous UHTCs were reviewed.Dry processing,colloidal processing and solution processing routes have been used to prepare porous UHTCs with porosities ranging from 5%to 97%and pore sizes ranging from hundreds of nanometers to hundreds of micrometers.The obtained porous UHTCs are chemically and dimensionally stable at temperatures up to 2000℃ during static state high-temperature thermal aging.

Temperature Effects on Photoluminescence Properties of Porous Silicon

The temperature effects on the photoluminescence(PL) properties of porous silicon(PS) have been observed in the early stage. However, the obtained results are different. Through repeated experiments, some different and useful information are got, which benefits us in that PL properties of porous silicon can be fully made use of. Firstly, samples with porosity of 76% and 49% were chosen to study the exciting temperature effects on the PL spectrum. For the samples with low porosity, the decreasing temperature causes the peak wavelength to be red-shifting and that of the samples with high porosity to present the blue-shifting trend. The light intensity of both reaches the maximum at -10℃. These experimental results can be well explained with the synthesized center PL model based on the quantum confinement model, other than the PL efficiency function σ(λ). Thereafter, PL properties of PS samples fabricated separately under the temperature of -10℃, 0℃, 10℃, 20℃ and 30℃ were studied. The results indicate that with the decrease of the etching temperature, the PL intensity increases from 406.7 to 716.6 and the peak wavelength blue-shifts from 698.9nm to 671.8nm. The WHFM of the PL spectrum dramatically narrows. At the same time, the images observed by AFM show that with the decreasing temperature, the holes are becoming deeper and the porosity is higher, which suggests that the decreasing temperature accelerates the etching rate.

Numerical Study of Natural Convection in a Porous Square Enclosure with Sinusoidally Varying Temperature Profile on the Bottom Wall

This current study focuses on the simulation of natural convection in square cavity filled with a porous medium considered homogenous, isotropic and saturated by a Newtonian fluid obeying the law of Darcy and the hypothesis of Boussinesq. The lower horizontal wall of the enclosure is subjected to a temperature varying sinusoidally with the space while the upper horizontal wall is maintained adiabatic. The vertical walls are kept cold isotherm. In order to generalize the results, all governing equations are put into dimensionless form, discretized by the Finite Difference Method and solved by the relaxed Gauss Seidel (SUR) Algorithm. A code has been proposed in Fortran 95, in order to solve numerically the equations of the problem. The study parameters are the Rayleigh-Darcy number (Ra) and the amplitude (Ar) of the hot wall temperature. The effects of the Rayleigh-Darcy number and amplitude on the dynamic and thermal field, the horizontal velocity distribution and the mean horizontal temperature distribution (y = 0.5) were presented and discussed. It emerges from this study that the increases of the amplitude and Rayleigh-Darcy number intensify the flow and the global transfer of heat in our physical domain.

Progress in Preparation Technology of Porous Ceramics for High Temperature Dust Filtration

With the rapid industrialization and urbanization,the demand for air quality management is more and more urgent.High temperature dust filtration is one important environmental management technology.Porous ceramics are used as filter materials in the field of high-temperature dust filtration because of their unique advantages such as high filtration efficiency,as well as high temperature stability,particle loss resistance,corrosion resistance and durability.This paper mainly introduced several common preparation techniques of porous ceramics,including the traditional organic foam impregnation method,foaming method,in-situ combustion method,pore-forming method and other new methods such as the template method,gel injection molding method,freeze-drying method,multi-component co-precipitation method and hydrogel method.The principle,advantages and disadvantages of these preparation technologies and their research status were described.The application of these technologies in the field of high temperature dust filtration was briefly reviewed.Finally,the application prospect of the porous ceramics in the field of high temperature dust filtration was prospected.

Si nanopillar arrays with nanocrystals produced by template-induced growth at room temperature

Well-aligned and closely-packed silicon nanopillar （SNP） arrays are fabricated by using a simple method with magnetron sputtering of Si on a porous anodic alumina （PAA） template at room temperature. The SNPs are formed by selective growth on the top of the PAA pore walls. The growth mechanism analysis indicates that the structure of the SNPs can be modulated by the pore spacing of the PAA and the sputtering process and is independent of the wall width of the PAA. Moreover, nanocrystals are identified by using transmission electron microscopy in the as-deposited SNP samples, which are related to the heat isolation structure of the SNPs. The Raman focus depth profile reveals a high crystallization ratio on the surface.

High-Performance and Flexible Co-Planar Integrated Microsystem of Carbon-Based All-Solid-State Micro-Supercapacitor and Real-Time Temperature Sensor

With the rapid development of flexible and portable microelectronics,the extreme demand for miniaturized,mechanically flexible,and integrated microsystems are strongly stimulated.Here,biomass-derived carbons(BDCs)are prepared by KOH activation using Qamgur precursor,exhibiting three-dimensional(3D)hierarchical porous structure.Benefiting from unobstructed 3D hierarchical porous structure,BDCs provide an excellent specific capacitance of 433 F g^(-1)and prominent cyclability without capacitance degradation after 50000 cycles at 50 A g^(-1).Furthermore,BDC-based planar micro-supercapacitors(MSCs)without metal collector,prepared by mask-assisted coating,exhibit outstanding areal-specific capacitance of 84 mF cm^(-2)and areal energy density of 10.6μWh cm^(-2),exceeding most of the previous carbon-based MSCs.Impressively,the MSCs disclose extraordinary flexibility with capacitance retention of almost 100%under extreme bending state.More importantly,a flexible planar integrated system composed of the MSC and temperature sensor is assembled to efficiently monitor the temperature variation,providing a feasible route for flexible MSC-based functional micro-devices.

Water-induced electrode poisoning and the mitigation strategy for high temperature polymer electrolyte membrane fuel cells

Engineering failure of membrane electrode assembly caused by increasingly fuel poisoning in the high temperature polymer electrolyte membrane fuel cells fed with humidified reformate gases is firstly demonstrated herein this work. Based on the results of the in-situ environmental scanning electron microscope, electrochemical analyses, and limiting current method, a water-induced phosphoric acid invasion model is constructed in the porous electrode to elucidate the failure causations of the hindered hydrogen mass transport and the enhanced carbon monoxide poisoning. To optimize the phosphoric acid distribution under the inevitably humidified circumstance, a facile and effective strategy of constructing acid-proofed electrode is proposed and demonstrates outstanding stability with highly humidified reformate gases as anode fuel. This work discusses a potential defect that was rarely studied previously under practical working circumstance for high temperature polymer electrolyte membrane fuel cells, providing an alternative opinion of electrode design based on the fundamental aspects towards the engineering problems.

Constructal design of a rectangular porous fin considering minimization of maximum temperature difference and pumping power consumption

A heat dissipation model of a rectangular porous fin is established based on constructal theory. First, the constructal design of rectangular porous fin is conducted by selecting a complex function minimization, which composed of linear weighting sum of maximum temperature difference and pumping power consumption, as optimization objective. Effects of gap height, air inlet velocity, total porous fin volume and porosity on the optimal constructs are investigated, respectively. The findings show that the complex function can attain its double minimum at a value of 0.802 when the fin length and number are optimized, and the corresponding optimal fin length and number are 8.01 mm and 10, respectively. In comparison to original design, the complex function and maximum temperature difference after twice optimization are decreased by 19.80% and 66.31%, respectively.Second, the comprehensive performance of porous fin is improved by simultaneously optimizing the fin length and number. The artificial neural network is applied to predict the fin performances, which is used to conduct multi-objective optimization based on NSGA-II algorithm. Optimal structure of porous fin for multiple requirements is gained by LINMAP and TOPSIS decisionmaking strategies. The findings in this study can serve as theoretical guides for fin thermal designs of electronic devices.

Porous Flame-retarded Asphalt Pavement for Highway Tunnel

A new way to improve the tunnel fire protection by using flame-retarded porous asphalt pavement containing ATH powders was introduced. Based on the miniature burning test designed and conducted, the burning time and temperature of porous asphalt （PA） and flame-retarded porous asphalt （FRPA） were studied comparing with cement concrete pavement, dense-graded lIMA and SMA. Results of burning test and pavement performance test indicate that FRPA is appropriate and suitable as the pavement material of highway tunnel.