Research on the variable speed system of large power alternating current motor

The development status of the variable speed system of large power AC(alternating current)motor drive in China is introduced.The large power AC drive fed by AC-AC converters(cycloconverters)has developed greatly,and some innovations on the theory and engineering technique have been realized.They have been applied to rolling mills,mine hoists,and so on,and remarkable economic and social benefit has been achieved.The development of AC drive fed by large power IGCT(integrated gate commutated thyristors)AC-DC-AC converter is also introduced.It has excellent performance and reliable operation,and has been used in traction.

STUDY ON POWER SPARE COEFFICIENT OF ELECTRICAL MOTOR IN LARGE PUMP STATION BASED ON RELIABILITY

Characters of head of low head pump station and the pump shaft power areanalyzed. Influence of each single factor on pump shaft power is expressed as change of specificshaft power. (non-dimensional) and the probability density function is determined. Influences ofmultiple factors on pump shaft power are analyzed. Method of calculating none over-loadedprobability of motor by integration by successive reductions is put forward and then relationbetween power spare coefficient and none over-loaded reliability of electric motor is established.Influences of all factors on pump shaft power being considered completely; power spare coefficientsof motor are calculated in three kinds of heads (changing and unchanging), two kinds of dirty-outconditions. Electrical motor power spare coefficients should be chosen as 1.20 approx 1.44, 1.11approx 1.19, 1.09 approx.14 respectively when pump heads are 4, 7, 9.5 m. The results mean much toreasonable choose of electrical motors in large pump stations, increasing reliability of pump unitsand saving equipment investment.

An Investigation of Power Converters Fed BLDC Motor for Adjustable Speed

This paper reports the converter topologies which are employed for better Power Factor Correction at the input side. The Power Factor Correction is an important factor when considering the Power Quality. Based on the converter topologies, the Bridgeless converters are preferred in order to reduce the number of switching devices, losses associated with it and improve the Power Quality further more. This paper investigates about the Power Factor performances and conduction losses of the Bridgeless Power Factor Corrector Converters which see through the benefits and limitations by analyzing the Bridgeless Buck-Boost Converter, Bridgeless SEPIC converter and Bridgeless CUK converter. The resultant voltage is fed to the BLDC motor which is rapidly replacing the Induction motor for its better operating characteristics. These strategies are being analyzed using the MATLAB/Simulink software and the results are verified through the experimental analysis. The converter choice is preferred through the performance characteristics and Power Factor Correction at the supply. The Power Factor obtained should be within the acceptable limits under IEC 61000-3-2 standards.

Study on Matching a 300 MVA Motor Generator with an Ohmic Heating Power Supply in HL-2M

A new 300 MVA/1350 MJ motor generator （MG） will be built to feed all of the poloidal field power supplies （PFPS） and auxiliary heating power supplies of the HL-2M tokamak. The MG has a vertical-shaft salient pole 6-phase synchronous generator and a coaxial 8500 kW induction motor. The Ohmic heating power supply （OHPS） consisting of 4-quadrant DC pulsed convertor is the one with the highest parameters among the PFPS. Therefore, the match between the generator and the OHPS is very important. The matching study with Matlab/Simulink is described in this paper. The simulation results show that the subtransient reactance of the generator is closely related to the inversion operation of the OHPS. By setting various subtransient reactance in the simulation generator model and considering the cost reduction, the optimized parameters are obtained as xd＂ = 0.405 p.u. at 100 Hz for the generator. The models built in the simulation can be used as an important tool for studying the dynamic characteristics and the control strategy of other HL-2M PFPSes.

Frequency control system based on power factor control of asynchronous motor

Deduced the relationship between the power factor (PF) and the angular fre-quency according to the simplified equivalent circuit of asynchronous motor, forming a power factor auto-control system. An anti-interference circuit was also introduced in the middle voltage link of inverter to avoid the shift of the optimum PF point caused by the change of the load and the reliable run of the control system was assured. The experi-ment results show that it has a good self-adaptation in the whole scope of speed ad-justment and an obvious economization on energy while it runs under load.

Efficiency of collective myosin Ⅱ motors studied with an elastic coupling power-stroke ratchet model

We proposed a modified ratchet model including power-stroke and elastic coupling to study the efficiency of collective non-processive motors such as myosin Ⅱ in muscle. Our theoretical results are in good agreement with the experimental data. Our study not only reveals that the maximum efficiency depends on elasticity and is independent of transition rates but also indicates that the parameters fitted to fast muscle are different from those fitted to a slow one. The latter may imply that the structure of the fast muscle is different from that of the slow one. The main reason that our model succeeds is that velocity in this model is an independent variable.

Dynamic Equivalent Method of Motor Loads for Power Systems Based on the Weighted

Dynamic equivalence can not only largely reduce the system size and the computation time but also stress the dominant features of the system [1]-[3]. This paper firstly recommends the basic concept of dynamic equivalent and the status of both domestic and abroad development in this area. The most existing equivalent methods usually only deal with static load models and neglect the dynamic characteristics of loads such as induction motors. In addition, the existing polymerization method which is based on the frequency domain algorithm of induction electric machines parameters takes a long time to equivalent for the large system, then the new method based on the weighted is proposed. Then, the basic steps for dynamic equivalence with the weighted method are introduced as follows. At first, the clustering criterion of motor loads based on time domain simulation is given. The motors with similar dynamic characteristics are classified into one group. Then, the simplication of the buses of motors in same group and network is carried out. Finally, parameters of the equivalent motor are calculated and the equivalent system is thus obtained based on the weighted. This aggregation method is applied to the simple distribution system of 4 generators. Simulation results show that the method can quickly obtain polymerization parameters of generator groups and the aggregation model retains the dynamic performance of the original model with good accuracy, the active and reactive power fitting error is smaller as well.

航空电推进电机多层波浪形拓扑及散热设计方法

针对航空电推进电机的散热问题,提出一种基于多层波浪形散热拓扑的航空电推进电机高效散热设计方法。航空电推进电机采用多层波浪形散热拓扑,建立电机等效热网络模型,确定等效热阻、对流换热系数等重要参数,完成电机温度精确计算,并通过CFD仿真验证所建立电机等效热网络模型的准确性和有效性。以此为基础,对比分析传统散热翅和多层波浪形散热拓扑对电机功率密度的影响。基于多层波浪形散热拓扑的等效热网络模型,采用遗传学习粒子群优化(GL-PSO)算法,完成航空电推进电机高效散热优化设计。优化结果表明:相比于原始方案,优化方案的机壳质量减轻15.1%,整个电机的功率密度提升0.06 kW/kg。

飞机电推进系统高效能电机及其驱动控制技术

飞机动力系统的电气化是继机载二次能源逐步统一为电能之后航空电气化发展的重要方向和高级阶段,能够大幅提升飞机动力系统能量利用效率,是航空业绿色发展的重要途径。电机系统是飞机电推进系统的核心机电能量变换环节,高效能电机、电力电子变换及其驱动控制技术是电推进飞机发展的基础支撑。该文从电推进飞机动力系统架构出发,分析电推进飞机电机系统的特征与要求。总结永磁同步电机、异步电机、电励磁无刷同步电机和超导电机4种类型电机在电推进飞机上的研究和应用现状,系统讨论电推进系统中不同类型电机和电机驱动器的关键技术。最后,展望新材料、新器件、新工艺、人工智能和综合热管理等技术对电推进飞机电机及其驱动控制技术发展的推动作用。

New Approach to the Power Selection for Asynchronous Motor

The heating calculation of three-phase squirrel- cage asynchronous motor on the condition of starting for a prescribed rotary angle is firstly studied with time dissection method and its corresponding algorithm is provided. Then based upon the algorithm, a new method for motor power selection is established. Motor initial power determined by load power ischecked and modified in terms of time crit erion, heating criterion,and starting torque criterion.An appropriate motor power which meets three criterions is obtained at last, in the meantime, working displacement matrix andfrequency matrix used for control are acquired. Lifting motor of MDJ1800 low-level high- speed palletizer is taken as a reaI case in the paper.

双轮毂电机驱动力矩在线分配控制方法研究

针对双轮毂电机驱动汽车的高效低耗能问题,提出一种考虑双轮毂电机驱动力矩在线实时反馈的优化方法。首先,建立轮毂电机能耗模型、动力学模型以及转矩分配控制模型;其次,以轮毂电机驱动效率为目标,以轮毂电机转矩、转速和能耗为不等式约束,建立基于加入异变序列的QPSO-LSTM算法的优化模型;最后,搭建Lab-VIEW软件实验平台,使轮毂电机在716 N·m转矩峰值和1000 r/min转速峰值的约束条件下稳定输出。结果表明,软件平台可实时监测并调整驱动车辆系统数据,在FTP-75工况下,加入异变序列的QPSO-LSTM算法比量子遗传算法和粒子群算法的单循环能耗分别降低了2.98%和4.64%;在CLTC-P工况下,单循环能耗分别降低了3.06%和4.81%。

Power Factor Improvement of AC-DC Converter Based on Separately Excited DC Motor Using Passive Filter

In industries DC motor drives are very essential due to their high performance applications such as its reliability, ease of control, low cost and simplicity. And speed control of these motors is very easy due to power electronic AC-DC converters. These power electronic converters are with prominent low power factor and higher Total Harmonic Distortion (THD). These converters operate only for short time resulting non-sinusoidal waveform. This problem of harmonic distortion can be mitigated by reshaping the non-sinusoidal waveform to pure sine wave. Different wave shaping techniques have been developed by using different filters among which one is tuned passive filter. This paper proposed power factor improvement and harmonic mitigation of AC-DC converters based on separately excited DC motor using tuned passive filter. In this context experimental model is designed and results are analyzed by power quality analyzer.

乘用车双电机冗余电动助力转向系统研究

为了提高电动助力转向系统的安全性以及可靠性,基于乘用车提出一种双电机冗余电动助力转向技术,采用转向执行双助力电机,可以从硬件上实现冗余,避免任意单电机发生故障时导致转向系统的失效,不仅可以满足转向系统对于轻便型、助力跟随性的要求,还可以减轻单个助力电机的负载提高电机的使用寿命。针对提出的问题,介绍了对双电机阻力转向系统整体结构及工作原理,并对其关键零部件进行分析论述。搭建双电机冗余系统仿真模型,双电机电流分配采用“一主一辅”的控制方式,并进行方向盘多种工况仿真验证。针对助力转向出现抖动问题,结合“扫频试验”,设计输出转矩超前滞后补偿方式进行相位校正补偿。通过实车试验验证了该算法的准确性和有效性。实验结果表明双冗余电动助力转向系统极大提高了转向力矩的稳定性,抑制其扰动性,有较好的助力效果,极大提高系统的可靠性和安全性。

高温快速地层压力测试仪研制与应用

随着勘探井向深井领域发展,高温深地深海小直径井眼油气的开发成为必然。快速地层压力测试仪是通过对地层压力测量来分析计算地层渗透率及储层有效性的仪器,但现有仪器不能满足4.5in*小直径井眼及耐温205℃的作业要求,测压时抽吸速度不可控,无法实现恒流抽吸,导致测压精确度低。高温快速地层压力测试仪各功能短节模块化设计,其液压动力与精密抽吸短节高度集成、推靠坐封短节结构紧凑,这使仪器的长度和直径得以减小;采用耐高温电子元器件和高温厚膜封装技术,实现仪器耐温205℃的技术指标;采用直流无刷电机精密控制技术实现对超低渗透率等复杂地层流体的恒流抽吸、精准测压。高温快速地层压力测试仪经过高温和可靠性测试及实井作业验证,该仪器具有尺寸小、集成度高、可靠性好、耐高温的优点,解决了高温复杂井况测压问题,具有较好的应用前景。

基于磁耦合谐振的多自由度电机无线电能传输

针对多自由度电机无线电能传输中传输效率较低的问题,提出基于磁耦合谐振的多自由度电机无线电能传输方法。该方法根据共振原理构建磁耦合谐振式无线电能传输模型,通过反射系数描述阻抗匹配状态,获取最佳负载阻抗;采用混沌优化算法优化电机线圈损耗率,实现多自由度电机无线电能传输优化。实验结果表明,应用该方法后,多自由度电机的电能输出功率达到了893 W,传输效率提升了0.10以上,提高了电能输出功率和传输效率,方法有效,具备可行性。

计及低电压穿越影响的感应电动机动态分群

随着新能源的大规模广泛并网,其对感应电动机动态等值建模的影响值得关注。该文提出了新能源电力系统中感应电动机动态分群新方法。分析了感应电动机与电网的交互作用,提出在现有基于感应电动机动态相似性分群的基础上,同时考虑机端电压动态相似性的分群可提高感应电动机动态等值精度。针对高比例新能源电力系统,研究发现感应电动机附近有新能源机组,且部分新能源机组在故障期间进入低电压穿越(LVRT)时,这些感应电动机动态特性具有显著差异。为此提出新能源电力系统中考虑感应电动机端口电压跌落深度的动态分群方法。算例分析表明,该文提出的兼顾感应电动机端口电压动态相似性以及端口电压跌落深度的分群方法具有较高的等值精度,且适应性强。

计及总损耗功率的电动汽车母线电容主动快速放电方法

针对电动汽车遇到碰撞等紧急情况时,高压驱动系统母线电容电压需迅速降到安全电压(60 V),而传统基于PI控制的母线电容主动放电方法存在鲁棒性差、放电时间长和安全性低的问题,提出一种计及总损耗功率的电动汽车母线电容快速放电方法。首先,建立以永磁同步电机绕组作为泄放电阻的母线电容能量流动模型,将逆变器损耗、电机绕组铜耗、电机电感储能等损耗作为总损耗,利用扩展滑模观测器(ESMO)对总损耗功率进行估算,并通过Lyapunov稳定性理论对ESMO的稳定性进行了证明。然后,将观测的总损耗功进行前馈补偿,从而使母线电压快速降低并稳定在安全电压。仿真和实验结果表明,与现有主动放电方法相比,所提放电方法不仅显著减小了放电时间,而且提高了快速放电的鲁棒性和安全性。

EXL-50U磁体线圈电源系统研制

新奥科技发展有限公司(新奥能源研究院)将原有紧凑型聚变研究装置EXL-50升级为EXL-50U,装置仍然是常温托卡马克,其磁场电源系统包括环向场TF(Toroidal Field)电源、中心螺线管CS(Center Solenoid)电源、PF1-10(Poloidal Field)极向场电源,共12套电源,所有电源均由交流脉冲发电机供电,使用相控整流方案。本文主要设计满足EXL-50U高参数需求的磁场电源,设计重点是提升电源能力,制定高参数工况下的保护策略,内容包括控制与保护系统、交流脉冲发电机的供电方案,变压器与变流器设计,最后给出了实际测试获得的各电源实际波形图,展示在中心螺线管击穿的条件下形成等离子体电流的电源工作波形,以验证设计电源的可靠性与可控性。

深海载人潜水器直流无刷电机驱动控制研究

为提高深海载人潜水器电机工作效率和故障诊断能力,并降低系统工作噪声,对直流无刷电机的高效低噪驱动控制技术进行研究。采用具有智能相位控制功能的三相全波正弦波控制芯片TB6605结合智能功率模块(IPM)设计直流无刷电机驱动器。采用单片机对系统的电压、电流、温度、转速、位置信息进行检测,为控制系统提供必要的信息反馈,对应用直流无刷电机的系统状态起到实时信息监测的功能。实验结果表明,研制的直流无刷电机驱动器在电机全转速范围内具有较高的工作效率,额定工况点效率高达90%以上,且在全转速范围内,提高了电机运转的平稳度,降低了系统噪声。研究成果对提高深海载人潜水器电机的工作效率和故障诊断能力,并降低系统工作噪声具有很好的支撑作用。

数据驱动与机理耦合的冷轧电机功率智能预测方法

电机功率计算在保证生产安全、制定轧制规程以及发挥设备能力等方面起到了重要作用。为提高计算精度,本文提出一种机理模型与数据驱动方法相结合的电机功率预测模型。首先,机理模型部分采用上界法得到解析解,然后将部分功率解析解(塑性变形功率、张力功率和剪切功率)与相关变量输入长短时记忆(long short-term memory,LSTM)网络中训练,以提取变量数据之间的深度特征和时序相关性。结果表明:本文提出的时序耦合预测模型相对误差不超过±3.9%,且在相邻卷带钢轧制规程变化较大时,预测效果明显优于上界法和人工神经网络(artificial neural networks,ANN);从残差分布直方图中可以看到,上界法由于遗漏了摩擦系数和损失功率与其他参数间的强耦合关系,导致残差集中在±50 kW附近且不符合正态分布,而ANN和本模型均基本遵循正态分布,但本模型拟合精度更高;对比更广泛的模型评估指标,本模型具有更好的综合预测性能。此外,通过模型输出结果分析了电机功率与轧制长度、轧制速度之间的关系,表明本模型除具有高预测精度外,还与已知的参数间物理规律有较强一致性。