Optimal Sizing and Power Losses Reduction of Photovoltaic Systems Using PVsyst Software

This paper presents a method for optimizing a grid-connected photovoltaic system through an LCL filter. An algorithm based on particle swarm optimization (PSO) is used to determine the number of batteries, the number of panels in series and in parallel, as well as to evaluate the joule losses due to cable heating and the switching losses of the multilevel inverters. This system is applied to a village named YAGOUA, located in the far north of Cameroon. The evaluation of the Joule effect and the switching losses as well as the regulation of the voltage level at the point of common coupling (PCC) are carried out in PVsyst and Matlab software, then at IEEE 33 bus. This algorithm reduced the Joule losses to 1.2% and the switching losses to 2.2%. A power of 210.4 MWh is produced, to be injected in the electrical network via an LCL filter. The THD calculation gave a rate of 3.015% in accordance with the 519 standards. Synchronization through the Phase Locked Loop (PLL) is performed. After the power was injected into the grid, the voltage and current remained in phase, showing the power factor correction and the efficiency of the filter. According to NASA meteorological data, the locality of YAGOUA gives the global solar irradiation forecast of 6.8 kW/m2.

Optimal Placement and Sizing of Distributed Generations for Power Losses Minimization Using PSO-Based Deep Learning Techniques

The integration of distributed generations (DGs) into distribution systems (DSs) is increasingly becoming a solution for compensating for isolated local energy systems (ILESs). Additionally, distributed generations are used for self-consumption with excess energy injected into centralized grids (CGs). However, the improper sizing of renewable energy systems (RESs) exposes the entire system to power losses. This work presents an optimization of a system consisting of distributed generations. Firstly, PSO algorithms evaluate the size of the entire system on the IEEE bus 14 test standard. Secondly, the size of the system is allocated using improved Particles Swarm Optimization (IPSO). The convergence speed of the objective function enables a conjecture to be made about the robustness of the proposed system. The power and voltage profile on the IEEE 14-bus standard displays a decrease in power losses and an appropriate response to energy demands (EDs), validating the proposed method.

Minimization of Electric Power Losses on 132 kV and 220 kV Uganda Electricity Transmission Lines

The classical minimization of power losses in transmission lines is dominated by artificial intelligence techniques, which do not guarantee global optimum amidst local minima. Revolutionary and evolutionary techniques are encumbered with sophisticated transformations, which weaken the techniques. Power loss minimization is crucial to the efficient design and operation of power transmission lines. Minimization of losses is one way to meet steady grid supply, especially at peak demand. Thus, this paper has presented a gradient technique to obtain optimal variables and values from the power loss model, which efficiently minimizes power losses by modifying the traditional power loss model that combines Ohm and Corona losses. Optimality tests showed that the unmodified model does not support the minimization of power losses on transmission lines as the Hessian matrix portrayed the maximization of power losses. However, the modified model is consistent with the gradient method of optimization, which yielded optimum variables and values from the power loss model developed in this study. The unmodified (modified) models for Bujagali-Kawanda 220 kV and Masaka West-Mbarara North 132 kV transmission lines in Uganda showed maximum power losses of 0.406 (0.391) and 0.452 (0.446) kW/km/phase respectively. These results indicate that the modified model is superior to the unmodified model in minimizing power losses in the transmission lines and should be implemented for the efficient design and operation of power transmission lines within and outside Uganda for the same transmission voltages.

General Properties of Low-frequency Power Losses in Fe-based Nanocrystalline Soft Magnetic Alloys

The dependences of the power loss per cycle on frequency f and amplitude flux density Bm have been investigated for the three main original magnetic states in five sorts of Fe-based nanocrystalline soft magnetic alloys in the ranges of 10 Hz<=f<=1000 Hz and 0.4 T<= Bm <=1.0 T. The total loss P is decomposed into the sum of the hysteresis loss Physt, the classical eddy current loss Pel and the excess loss Pexc. Physt has been found to be proportional to Bm^2 and f. The behavior of Pexc/f vs f being equivalent to P/f vs f clearly exhibits nonlinearity in the range not more than about 120 Hz, whereas the behavior of P/f vs f roughly shows linearity in the range far above 100 Hz and not more than 1000 Hz. In the range up to 1000 Hz, Physt is dominant in the original high permeability state and the state of low residual flux density, whereas Pexc in the state of high residual flux density is dominant in the wider range above about 100 Hz. The framework of the statistical theory of power loss has been used for representing the behavior of Pexc/f vs f. It has been found that the number n of the simultaneously active 'Magnetic Objects' linearly varies as n = n0 + Hexc/H0 as a function of the dynamic field Hexc in the range below about 120 Hz, whereas n approximately follows a law of the form n = n0 + (Hexc/H0)^m with 1 < m < 2 in the range far above 100 Hz and not more than 1000 Hz. The values of the field HO in principle related to the microstructure and the domain structure have been calculated for the three states.

Electrical Power Losses in a Photovoltaic Solar Cell Operating under Partial Shading Conditions

The aim of this paper is to determine the power losses recorded by a PV generator operating under partial shading conditions. These losses are evaluated through two distinct methods. The first method is based on mathematical modeling, while the second is based on Simulink’s physical model. The losses recorded are considerable and increase as a function of the increase in the percentage of shading up to a limit value where they become constant in the case where an ideal by-pass diode is connected in parallel with the modules. This limit value is non-existent in the case where the bypass diode is not ideal, which in fact corresponds to the real model. However, it emerges that the power losses are minimized in a PV system comprising bypass diodes, in particular in the case where the partial shading is considerable.

Deciphering the Origins of P1-Induced Power Losses in Cu(In_(x),Ga_(1–x))Se2(CIGS)Modules Through Hyperspectral Luminescence

In this report,we show that hyperspectral high-resolution photoluminescence mapping is a powerful tool for the selection and optimiz1ation of the laser ablation processes used for the patterning interconnections of subcells on Cu(Inx,Ga1-x)Se2(CIGS)modules.In this way,we show that in-depth monitoring of material degradation in the vicinity of the ablation region and the identification of the underlying mechanisms can be accomplished.Specifically,by analyzing the standard P1 patterning line ablated before the CIGS deposition,we reveal an anomalous emission-quenching effect that follows the edge of the molybdenum groove underneath.We further rationalize the origins of this effect by comparing the topography of the P1 edge through a scanning electron microscope(SEM)cross-section,where a reduction of the photoemission cannot be explained by a thickness variation.We also investigate the laser-induced damage on P1 patterning lines performed after the deposition of CIGS.We then document,for the first time,the existence of a short-range damaged area,which is independent of the application of an optical aperture on the laser path.Our findings pave the way for a better understanding of P1-induced power losses and introduce new insights into the improvement of current strategies for industry-relevant module interconnection schemes.

Optimal Placement of Reclosers to Minimize Power Losses during Non-Load Bearing Disturbances in a Power Distribution Using Firefly Algorithm

The research reported in this paper focuses on non-technical power loss reduction for power distribution systems. Such reduction of costs of energy not served (ENS.COST), is intelligently evaluated and optimized using a firefly algorithm, from where savings of 43.3% on energy not served are achieved.

Calculation of Skin Depths and Eddy-Current Power Losses for Magnetic Position Sensors

We present a theoretic model to calculate skin depths and eddy-current power losses for a magnetic position sensor. Eddy-current, arised from the operation of an alternating-current excitation, induces secondary currents and fields between magnetic material and magnetic position sensor. In this paper, a magnetic position sensor system is simplified to be an outer-winding coil along the axial direction of a low carbon steel bar. The analytical model is derived from basic field and circuit theory considering a linear approximation for a nonlinear permeability. Thus the skin depths and eddy-current power losses from the model in eddy-current modeling techniques at various frequencies of an excited current source can be calculated. The proposed configuration is capable of predicting the skin depths and eddy-current power losses for a magnetic position sensor and has a consistence with experiments.

Diagnosis of Thermal Overload and Power Losses in Boat Yang 1’s CAT 3408 Marine Diesel Engine from Used Oil and Coolant Analysis

In the design of the CAT 3408 engine, the Low Temperature (BT) circuits used to cool the engine lubricating oil and the charge air and the High Temperature (HT) circuits for cooling the cylinder liners, cylinder heads and body of turbofans are mainly used to cool the engine, so that it works properly. This work, based on the analysis carried out, to determine the lubrication compliance of the Yacco VX 100 - SAE 15 W-40 oil and that of the Camwater water used in the engine of the Boat Yang 1 by carrying out a series of conventional tests such as that: the density, the viscosity, the viscosity index, the flash point, the density, the sulphate center content, the water content, the total acidity index (TAN), total basic number (TBN) and pour point for the oil case and pH, hardness, sodium chloride content [NaCl], sodium sulphate content [NaSO4] for the water case which will be compared to the specified requirements to determine whether compliance is achieved for each of these characteristics. The results of the oil and water samples taken from the engine after use show that the used oil gives a specific gravity of 0.8822, a viscosity (at 40°C) of 92.29 mm2/s, a viscosity (at 100°C) of 13.99 mm2/s, a viscosity index (VI) of 155.39, a pour point -21°C, a Flash Point (VO) 215°C, a Sulfated ash content of 18%, a density 881.5 kg/m3, a total basic number (TBN) of 12.60 mgKOH/g, a Total Acid Index (TAN) of 3.096 mgKOH/g, a Water Content of 1.8 % and the water used gives a pH of 6.00, a hardness of 3.2 french degrees, a sodium chloride content [NaCl] of 0.468 mg/L, and a calcium sulphate content [CaSO4] of 2.38345 mg/L. the results of the water content and content of sulfated centers justify the thermal overload and power losses in the marine diesel engine CAT 3408 of the boat Yang 1 because of their values which are not in conformity with the standards.

Impact of the PV Location in Distribution Networks on Network Power Losses and Voltage Fluctuations with PSO Analysis

Increased grid integration of photovoltaic(PV)has aggravated the uncertainty of distribution network operations.For a distribution network with PV,the impact of the PV location on the network power losses and voltage fluctuations is investigated with analytical derivations reflected by the line impedance.Optimization approaches of the PV location with consideration of two aspects,i.e.,minimum network power losses and minimum voltage fluctuations,are analyzed.A particle swarm optimization(PSO)algorithm is used to synthesize an optimal compromised solution so as to determine the PV location.A 10 kV distribution network with one PV is established on the time-domain simulation environment PSCAD/EMTDC.The simulation results justify the theoretical analysis and indicate that when the active power of the PV is more/less than twice that of the overall loads/end loads,the network power losses and node voltage fluctuations are both minimum when the PV is integrated into the head/tail end of the network.When the active power of the PV is between the above two conditions,nodes t/f can be identified for the integration of the PV between the head/end nodes of the network to achieve the minimum network power losses/voltage fluctuations,respectively.The effectiveness of the proposed optimization approach is verified and can provide a reference for selecting the PV location in the distribution network.

Optimal PV Array Configuration for Extracting Maximum Power Under Partial Shading Conditions by Mitigating Mismatching Power Losses

The grid-connected or standalone PV central inverter architecture is comprised of several PV modules which are connected in different ways to form the PV array.The power generation capability of the PV array is primarily affected by partial shading conditions(PSC).Due to PSCs,the power output of the PV array is dramatically reduced,and mismatching losses are induced in the PV modules.Based on the extent of these problems,multiple peaks also appear in the power-voltage(P-V)curve,which makes it very difficult to track the global maximum power point(GMPP).The main objective of this research paper is to model and simulate the series(S),series-parallel(SP),bridge-link(BL),honey-comb(HC),total-cross-tied(TCT)and proposed triple-tied(TT)solar PV array configurations under various partial shading scenarios.The performance of all PV configurations is evaluated under a uniform approach,considering eight different shading scenarios.The performance of the considered PV configurations is analyzed in terms of their mismatching power losses,fill factors,efficiency,global maximum power points(GMPPs),local maximum power points(LMPPs),voltages and currents at GMPPs,open circuit voltage and short circuit currents.The above-mentioned PV configurations are modeled and simulated in a Matlab/Simulink environment by considering the KC-200GT module parameters.

Comparative study of semiconductor power losses between CSI-based STATCOM and VSI-based STATCOM,both used for unbalance compensation

In this paper,we present a detailed procedure to determine the semiconductor losses for both structures of a shunt STATCOM(Static Compensator),STATCOM based on Current Source Inverter(CSI)and STATCOM based on Voltage Source Inverter(VSI),both used for voltage unbalance compensation.As a first step,we study the VSI-based STATCOM and the CSI-based STATCOM used in high speed railway substations.Then we analyze the design and the sizing of the unbalance compensator in order to obtain an unbalance factor that does not exceed the limits imposed by the standards or by the energy provider.Following that,we compare the performances obtained with both structures VSI-STATCOM and CSI-STATCOM,after calculating the semiconductor power losses in the STATCOM converters.Finally,we validate our approach by simulation over real data of unbalance compensation caused by the new high-speed railway in Morocco.We use the tools MATLAB/Simulink/Simpowersys for performing our simulations.

Optimal integration of DGs into radial distribution network in the presence of plug-in electric vehicles to minimize daily active power losses and to improve the voltage profile of the system using bioinspired optimization algorithms

Purpose:The increase in plug-in electric vehicles(PEVs)is likely to see a noteworthy impact on the distribution system due to high electric power consumption during charging and uncertainty in charging behavior.To address this problem,the present work mainly focuses on optimal integration of distributed generators(DG)into radial distribution systems in the presence of PEV loads with their charging behavior under daily load pattern including load models by considering the daily(24 h)power loss and voltage improvement of the system as objectives for better system performance.Design/methodology/approach:To achieve the desired outcomes,an efficient weighted factor multi-objective function is modeled.Particle Swarm Optimization(PSO)and Butterfly Optimization(BO)algorithms are selected and implemented to minimize the objectives of the system.A repetitive backward-forward sweep-based load flow has been introduced to calculate the daily power loss and bus voltages of the radial distribution system.The simulations are carried out using MATLAB software.Findings:The simulation outcomes reveal that the proposed approach definitely improved the system performance in all aspects.Among PSO and BO,BO is comparatively successful in achieving the desired objectives.Originality/value:The main contribution of this paper is the formulation of the multi-objective function that can address daily active power loss and voltage deviation under 24-h load pattern including grouping of residential,industrial and commercial loads.Introduction of repetitive backward-forward sweep-based load flow and the modeling of PEV load with two different charging scenarios.

Voltage Profile Enhancement and Power Loss Reduction with Economic Feasibility Using Small Capacity Distribution Transformers

Usually,rural areas can be electrified via three-phase distribution transformers with relatively large capacities.In such areas,low voltage lines are used for long distances,which cause power losses and voltage drop for different types of consumers.Reducing losses and improving voltage profiles in rural distribution networks are significant challenges for electricity distribution companies.However different solutions were proposed in the literature to overcome these challenges,most of them face difficulties when applied in the conventional distribution network.To address the above issues,an applicable solution is proposed in this paper by installing a number of small-capacity distribution transformers instead of every single large-capacity transformer in rural areas.The proposed approach is implemented in the branch network of Al-Hoqool village,which belongs to the Nineveh distribution network.The network has been inspected on-site,drawn,and analyzed using the electrical systems analysis program(ETAP).The analysis showed that using the single-phase pole-mounted transformers can improve the voltage in the network’s end by 29%and enhance the voltage profile for all consumers.The analysis has also demonstrated that the modification can reduce the total power losses by 78%compared to the existing network.Concerning the economic aspect,the payback period for the proposed network is assigned to be 20 months.

Electric Power Quality Analysis 6-10/0.4 kV Distribution Networks

The paper reports quality analysis and evaluation at 6 - 10/0.4 kV low-voltage distribution grids in Uzbekistan. Power quality frequently does not correspond to the rated value which is largely due to unbalanced phase loading in grids and which also results in increased power loss. The study of the asymmetrical operating modes of the rural distribution networks of 0.4 kV was conducted in three steps: measurement, calculations and analysis of relevant data;providing practical guidelines and finally, implementing instruments to normalize grid operation. Measuring was conducted using certified instrumentation analyzer “MALIKA” designed by authors. The study and analysis of additional power losses as the function of indicators of asymmetrical features of voltage and current in operating 0.4 kV grids reveals that, quality of electric power at grids under investigation, merely does not meet the requirements of the Interstate Standard.

Effects of Dimensional Tolerances on the Friction Power Loss of Hydrodynamic Journal Bearing System

According to the dimensional tolerances on hydrodynamic journal bearing system, a nonlinear oil film force model was established,and the Reynolds' equation was solved by adopting finite difference method. In order to fulfill different dimensional tolerances in the system,adopting 2kfactor design and using the eccentricity ratio corresponding to the stability critical curve,the effects of the friction power loss brought by the dimensional tolerances of the dynamic viscosity,bearing width,bearing diameter and journal diameter were analyzed. The effect on dynamic characteristics of the hydrodynamic journal bearing system was quantitatively analyzed,and the nonlinear dynamic analysis, modeling and calculation methods were studied while considering the manufacturing tolerances. The results show that in contrast to the impacts of the tolerances in journal diameter,dynamic viscosity and bearing width,the bearing diameter tolerance would lead to the rise in the power loss, and the dimensional tolerances have different degrees of impacts on the journal bearing system. The friction power loss decreased as the eccentricity ratio increased, and when the eccentricity ratio was 0. 695 the power loss came to the minimum.The investigation would find the best solution and reduce energy consumption,then control varieties of nonlinear dynamical behavior effectively,and provide a theoretical basis for hydrodynamic journal bearing system in parameter design.

Loss of offsite power (LOOP) accident analysis by integration of deterministic and probabilistic approaches in Bushehr-1 VVER-1000/V446 nuclear power plant

The results of an accident analysis for the loss of offsite power(LOOP)scenario in a reference Bushehr-1 VVER-1000/V446 nuclear power plant(NPP)are presented in this paper.This study attempted to provide a better analysis of LOOP accident management by integrating deterministic and probabilistic approaches.The RELAP5 code was used to investigate the occurrence of specific thermal–hydraulic phenomena.The probabilistic safety assessment of the LOOP accident is presented using the SAPHIRE software.LOOP accident data were extracted from the Bushehr NPP final safety analysis reports and probabilistic safety analysis reports.A deterministic approach was used to reduce the core damage frequency in the probabilistic analysis of LOOP accidents.The probabilistic approach was used to better observe the philosophy of defense in depth and safety margins in the deterministic analysis of the LOOP accident.The results show that the integration of the two approaches in LOOP accident investigations improved accident control.

Effect of V2O5-CaCO3-Nb2O5 Contents on Properties of Low Power Loss Mn-Zn Ferrites

Effect of the content of dopants in the manganese-zinc ferrites on the low power loss is studied by measuring magnetic properties and observing the grain boundary structures. The Mn0.738Zn0.206Fe2.066O4 composition powders were prepared by using conventional ceramic powder processing technique. The microstructure of grain boundary was observed by scanning electron microscope （SEM）. It has been found that power loss is greatly dependent upon the content of the additives.

Lifetime estimation of IGBT module using square-wave loss discretization and power cycling test

The insulated gate bipolar transistor(IGBT)module is one of the most age-affected components in the switch power supply, and its reliability prediction is conducive to timely troubleshooting and reduction in safety risks and unnecessary costs. The pulsed current pattern of the accelerator power supply is different from other converter applications;therefore, this study proposed a lifetime estimation method for IGBT modules in pulsed power supplies for accelerator magnets. The proposed methodology was based on junction temperature calculations using square-wave loss discretization and thermal modeling.Comparison results showed that the junction temperature error between the simulation and IR measurements was less than 3%. An AC power cycling test under real pulsed power supply applications was performed via offline wearout monitoring of the tested power IGBT module. After combining the IGBT4 PC curve and fitting the test results,a simple corrected lifetime model was developed to quantitatively evaluate the lifetime of the IGBT module,which can be employed for the accelerator pulsed power supply in engineering. This method can be applied to other IGBT modules and pulsed power supplies.

Analysis of DC Power Transmission Using High T_c Superconducting Cables

A conceptual superconducting DC cable model is designed and its magnetic fields distribution is analyzed with Ansoft/Maxwell soft. A DC Power transmission system is also studied by using the Matlab/Simulink. With the DC Line and AC Ground Fault, the system losses analysis is introduced.The analysis results mainly include the magnetic fields distribution of the HTS cable model with Ansoft/Maxwell, the system loss, the DC Line and AC Ground Fault with Matlab/Simulation.